| Message ID | 1411976660-19329-1-git-send-email-olli.salonen@iki.fi (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hello, In hardware design, the CI host controller is wired with GPIO_0 of CX23885. The GPIO_0 can be configed as the interrupt source. Interrupt mode in PCIe driver is more faster than poll mode to detect CAM insert/remove operations etc. >Add CI support for DVBSky T980C. > >I used the new host device independent CIMaX SP2 I2C driver to implement it. > >cx23885_sp2_ci_ctrl function is borrowed entirely from cimax2.c. > >Signed-off-by: Olli Salonen <olli.salonen@iki.fi> >--- > drivers/media/pci/cx23885/cx23885-dvb.c | 105 +++++++++++++++++++++++++++++++- > 1 file changed, 103 insertions(+), 2 deletions(-) > >diff --git a/drivers/media/pci/cx23885/cx23885-dvb.c b/drivers/media/pci/cx23885/cx23885-dvb.c >index cc88997..70dbcd6 100644 >--- a/drivers/media/pci/cx23885/cx23885-dvb.c >+++ b/drivers/media/pci/cx23885/cx23885-dvb.c >@@ -71,6 +71,7 @@ > #include "si2165.h" > #include "si2168.h" > #include "si2157.h" >+#include "sp2.h" > #include "m88ds3103.h" > #include "m88ts2022.h" > >@@ -616,6 +617,76 @@ static int dvbsky_t9580_set_voltage(struct dvb_frontend *fe, > return 0; > } > >+static int cx23885_sp2_ci_ctrl(void *priv, u8 read, int addr, >+ u8 data, int *mem) >+{ >+ >+ /* MC417 */ >+ #define SP2_DATA 0x000000ff >+ #define SP2_WR 0x00008000 >+ #define SP2_RD 0x00004000 >+ #define SP2_ACK 0x00001000 >+ #define SP2_ADHI 0x00000800 >+ #define SP2_ADLO 0x00000400 >+ #define SP2_CS1 0x00000200 >+ #define SP2_CS0 0x00000100 >+ #define SP2_EN_ALL 0x00001000 >+ #define SP2_CTRL_OFF (SP2_CS1 | SP2_CS0 | SP2_WR | SP2_RD) >+ >+ struct cx23885_tsport *port = priv; >+ struct cx23885_dev *dev = port->dev; >+ int ret; >+ int tmp; >+ unsigned long timeout; >+ >+ mutex_lock(&dev->gpio_lock); >+ >+ /* write addr */ >+ cx_write(MC417_OEN, SP2_EN_ALL); >+ cx_write(MC417_RWD, SP2_CTRL_OFF | >+ SP2_ADLO | (0xff & addr)); >+ cx_clear(MC417_RWD, SP2_ADLO); >+ cx_write(MC417_RWD, SP2_CTRL_OFF | >+ SP2_ADHI | (0xff & (addr >> 8))); >+ cx_clear(MC417_RWD, SP2_ADHI); >+ >+ if (read) { /* data in */ >+ cx_write(MC417_OEN, SP2_EN_ALL | SP2_DATA); >+ } else /* data out */ >+ cx_write(MC417_RWD, SP2_CTRL_OFF | data); >+ >+ /* chip select 0 */ >+ cx_clear(MC417_RWD, SP2_CS0); >+ >+ /* read/write */ >+ cx_clear(MC417_RWD, (read) ? SP2_RD : SP2_WR); >+ >+ timeout = jiffies + msecs_to_jiffies(1); >+ for (;;) { >+ tmp = cx_read(MC417_RWD); >+ if ((tmp & SP2_ACK) == 0) >+ break; >+ if (time_after(jiffies, timeout)) >+ break; >+ udelay(1); >+ } >+ >+ cx_set(MC417_RWD, SP2_CTRL_OFF); >+ *mem = tmp & 0xff; >+ >+ mutex_unlock(&dev->gpio_lock); >+ >+ if (!read) >+ if (*mem < 0) { >+ ret = -EREMOTEIO; >+ goto err; >+ } >+ >+ return 0; >+err: >+ return ret; >+} >+ > static int cx23885_dvb_set_frontend(struct dvb_frontend *fe) > { > struct dtv_frontend_properties *p = &fe->dtv_property_cache; >@@ -944,11 +1015,11 @@ static int dvb_register(struct cx23885_tsport *port) > struct vb2_dvb_frontend *fe0, *fe1 = NULL; > struct si2168_config si2168_config; > struct si2157_config si2157_config; >+ struct sp2_config sp2_config; > struct m88ts2022_config m88ts2022_config; > struct i2c_board_info info; > struct i2c_adapter *adapter; >- struct i2c_client *client_demod; >- struct i2c_client *client_tuner; >+ struct i2c_client *client_demod, *client_tuner, *client_ci; > int mfe_shared = 0; /* bus not shared by default */ > int ret; > >@@ -1683,6 +1754,7 @@ static int dvb_register(struct cx23885_tsport *port) > break; > case CX23885_BOARD_DVBSKY_T980C: > i2c_bus = &dev->i2c_bus[1]; >+ i2c_bus2 = &dev->i2c_bus[0]; > > /* attach frontend */ > memset(&si2168_config, 0, sizeof(si2168_config)); >@@ -1820,6 +1892,35 @@ static int dvb_register(struct cx23885_tsport *port) > case CX23885_BOARD_DVBSKY_T980C: { > u8 eeprom[256]; /* 24C02 i2c eeprom */ > >+ /* attach CI */ >+ memset(&sp2_config, 0, sizeof(sp2_config)); >+ sp2_config.dvb_adap = &port->frontends.adapter; >+ sp2_config.priv = port; >+ sp2_config.ci_control = cx23885_sp2_ci_ctrl; >+ memset(&info, 0, sizeof(struct i2c_board_info)); >+ strlcpy(info.type, "sp2", I2C_NAME_SIZE); >+ info.addr = 0x40; >+ info.platform_data = &sp2_config; >+ request_module(info.type); >+ client_ci = i2c_new_device(&i2c_bus2->i2c_adap, &info); >+ if (client_ci == NULL || >+ client_ci->dev.driver == NULL) { >+ module_put(client_tuner->dev.driver->owner); >+ i2c_unregister_device(client_tuner); >+ module_put(client_demod->dev.driver->owner); >+ i2c_unregister_device(client_demod); >+ goto frontend_detach; >+ } >+ if (!try_module_get(client_ci->dev.driver->owner)) { >+ i2c_unregister_device(client_ci); >+ module_put(client_tuner->dev.driver->owner); >+ i2c_unregister_device(client_tuner); >+ module_put(client_demod->dev.driver->owner); >+ i2c_unregister_device(client_demod); >+ goto frontend_detach; >+ } >+ port->i2c_client_ci = client_ci; >+ > if (port->nr != 1) > break; > >-- >1.9.1 > >-- >To unsubscribe from this list: send the line "unsubscribe linux-media" in >the body of a message to majordomo@vger.kernel.org >More majordomo info at http://vger.kernel.org/majordomo-info.html >. -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Max, Thanks for the comments. I looked through the existing CIMaX driver and came to the conclusion that it can be implemented either with the IRQs or then just to rely on the polling like the USB devices have to do. I don't think it's that important, as the user probably will not add/remove the CAM that often. That being said, of course it would be nice if we had a config option to choose if IRQ is supported or not. If you have a patch for that, I'm happy to have it in. Cheers, -olli On 29 September 2014 15:05, Nibble Max <nibble.max@gmail.com> wrote: > Hello, > In hardware design, the CI host controller is wired with GPIO_0 of CX23885. > The GPIO_0 can be configed as the interrupt source. > Interrupt mode in PCIe driver is more faster than poll mode to detect CAM insert/remove operations etc. > >>Add CI support for DVBSky T980C. >> >>I used the new host device independent CIMaX SP2 I2C driver to implement it. >> >>cx23885_sp2_ci_ctrl function is borrowed entirely from cimax2.c. >> >>Signed-off-by: Olli Salonen <olli.salonen@iki.fi> >>--- >> drivers/media/pci/cx23885/cx23885-dvb.c | 105 +++++++++++++++++++++++++++++++- >> 1 file changed, 103 insertions(+), 2 deletions(-) >> >>diff --git a/drivers/media/pci/cx23885/cx23885-dvb.c b/drivers/media/pci/cx23885/cx23885-dvb.c >>index cc88997..70dbcd6 100644 >>--- a/drivers/media/pci/cx23885/cx23885-dvb.c >>+++ b/drivers/media/pci/cx23885/cx23885-dvb.c >>@@ -71,6 +71,7 @@ >> #include "si2165.h" >> #include "si2168.h" >> #include "si2157.h" >>+#include "sp2.h" >> #include "m88ds3103.h" >> #include "m88ts2022.h" >> >>@@ -616,6 +617,76 @@ static int dvbsky_t9580_set_voltage(struct dvb_frontend *fe, >> return 0; >> } >> >>+static int cx23885_sp2_ci_ctrl(void *priv, u8 read, int addr, >>+ u8 data, int *mem) >>+{ >>+ >>+ /* MC417 */ >>+ #define SP2_DATA 0x000000ff >>+ #define SP2_WR 0x00008000 >>+ #define SP2_RD 0x00004000 >>+ #define SP2_ACK 0x00001000 >>+ #define SP2_ADHI 0x00000800 >>+ #define SP2_ADLO 0x00000400 >>+ #define SP2_CS1 0x00000200 >>+ #define SP2_CS0 0x00000100 >>+ #define SP2_EN_ALL 0x00001000 >>+ #define SP2_CTRL_OFF (SP2_CS1 | SP2_CS0 | SP2_WR | SP2_RD) >>+ >>+ struct cx23885_tsport *port = priv; >>+ struct cx23885_dev *dev = port->dev; >>+ int ret; >>+ int tmp; >>+ unsigned long timeout; >>+ >>+ mutex_lock(&dev->gpio_lock); >>+ >>+ /* write addr */ >>+ cx_write(MC417_OEN, SP2_EN_ALL); >>+ cx_write(MC417_RWD, SP2_CTRL_OFF | >>+ SP2_ADLO | (0xff & addr)); >>+ cx_clear(MC417_RWD, SP2_ADLO); >>+ cx_write(MC417_RWD, SP2_CTRL_OFF | >>+ SP2_ADHI | (0xff & (addr >> 8))); >>+ cx_clear(MC417_RWD, SP2_ADHI); >>+ >>+ if (read) { /* data in */ >>+ cx_write(MC417_OEN, SP2_EN_ALL | SP2_DATA); >>+ } else /* data out */ >>+ cx_write(MC417_RWD, SP2_CTRL_OFF | data); >>+ >>+ /* chip select 0 */ >>+ cx_clear(MC417_RWD, SP2_CS0); >>+ >>+ /* read/write */ >>+ cx_clear(MC417_RWD, (read) ? SP2_RD : SP2_WR); >>+ >>+ timeout = jiffies + msecs_to_jiffies(1); >>+ for (;;) { >>+ tmp = cx_read(MC417_RWD); >>+ if ((tmp & SP2_ACK) == 0) >>+ break; >>+ if (time_after(jiffies, timeout)) >>+ break; >>+ udelay(1); >>+ } >>+ >>+ cx_set(MC417_RWD, SP2_CTRL_OFF); >>+ *mem = tmp & 0xff; >>+ >>+ mutex_unlock(&dev->gpio_lock); >>+ >>+ if (!read) >>+ if (*mem < 0) { >>+ ret = -EREMOTEIO; >>+ goto err; >>+ } >>+ >>+ return 0; >>+err: >>+ return ret; >>+} >>+ >> static int cx23885_dvb_set_frontend(struct dvb_frontend *fe) >> { >> struct dtv_frontend_properties *p = &fe->dtv_property_cache; >>@@ -944,11 +1015,11 @@ static int dvb_register(struct cx23885_tsport *port) >> struct vb2_dvb_frontend *fe0, *fe1 = NULL; >> struct si2168_config si2168_config; >> struct si2157_config si2157_config; >>+ struct sp2_config sp2_config; >> struct m88ts2022_config m88ts2022_config; >> struct i2c_board_info info; >> struct i2c_adapter *adapter; >>- struct i2c_client *client_demod; >>- struct i2c_client *client_tuner; >>+ struct i2c_client *client_demod, *client_tuner, *client_ci; >> int mfe_shared = 0; /* bus not shared by default */ >> int ret; >> >>@@ -1683,6 +1754,7 @@ static int dvb_register(struct cx23885_tsport *port) >> break; >> case CX23885_BOARD_DVBSKY_T980C: >> i2c_bus = &dev->i2c_bus[1]; >>+ i2c_bus2 = &dev->i2c_bus[0]; >> >> /* attach frontend */ >> memset(&si2168_config, 0, sizeof(si2168_config)); >>@@ -1820,6 +1892,35 @@ static int dvb_register(struct cx23885_tsport *port) >> case CX23885_BOARD_DVBSKY_T980C: { >> u8 eeprom[256]; /* 24C02 i2c eeprom */ >> >>+ /* attach CI */ >>+ memset(&sp2_config, 0, sizeof(sp2_config)); >>+ sp2_config.dvb_adap = &port->frontends.adapter; >>+ sp2_config.priv = port; >>+ sp2_config.ci_control = cx23885_sp2_ci_ctrl; >>+ memset(&info, 0, sizeof(struct i2c_board_info)); >>+ strlcpy(info.type, "sp2", I2C_NAME_SIZE); >>+ info.addr = 0x40; >>+ info.platform_data = &sp2_config; >>+ request_module(info.type); >>+ client_ci = i2c_new_device(&i2c_bus2->i2c_adap, &info); >>+ if (client_ci == NULL || >>+ client_ci->dev.driver == NULL) { >>+ module_put(client_tuner->dev.driver->owner); >>+ i2c_unregister_device(client_tuner); >>+ module_put(client_demod->dev.driver->owner); >>+ i2c_unregister_device(client_demod); >>+ goto frontend_detach; >>+ } >>+ if (!try_module_get(client_ci->dev.driver->owner)) { >>+ i2c_unregister_device(client_ci); >>+ module_put(client_tuner->dev.driver->owner); >>+ i2c_unregister_device(client_tuner); >>+ module_put(client_demod->dev.driver->owner); >>+ i2c_unregister_device(client_demod); >>+ goto frontend_detach; >>+ } >>+ port->i2c_client_ci = client_ci; >>+ >> if (port->nr != 1) >> break; >> >>-- >>1.9.1 >> >>-- >>To unsubscribe from this list: send the line "unsubscribe linux-media" in >>the body of a message to majordomo@vger.kernel.org >>More majordomo info at http://vger.kernel.org/majordomo-info.html >>. > > -- > To unsubscribe from this list: send the line "unsubscribe linux-media" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Reviewed-by: Antti Palosaari <crope@iki.fi> Antti On 09/29/2014 10:44 AM, Olli Salonen wrote: > This patch adds basic support for DVBSky T980C card. CI interface is not supported. > > DVBSky T980C is a PCIe card with the following components: > - CX23885 PCIe bridge > - Si2168-A20 demodulator > - Si2158-A20 tuner > - CIMaX SP2 CI chip > > The demodulator and tuner need firmware. They're the same as used with TT CT2-4650 CI: > https://www.mail-archive.com/linux-media@vger.kernel.org/msg78033.html > > Signed-off-by: Olli Salonen <olli.salonen@iki.fi> > --- > drivers/media/pci/cx23885/cx23885-cards.c | 40 ++++++++++++++++++++ > drivers/media/pci/cx23885/cx23885-dvb.c | 61 +++++++++++++++++++++++++++++++ > drivers/media/pci/cx23885/cx23885.h | 1 + > 3 files changed, 102 insertions(+) > > diff --git a/drivers/media/pci/cx23885/cx23885-cards.c b/drivers/media/pci/cx23885/cx23885-cards.c > index 88c257d..e8965e6 100644 > --- a/drivers/media/pci/cx23885/cx23885-cards.c > +++ b/drivers/media/pci/cx23885/cx23885-cards.c > @@ -680,6 +680,10 @@ struct cx23885_board cx23885_boards[] = { > .portb = CX23885_MPEG_DVB, > .portc = CX23885_MPEG_DVB, > }, > + [CX23885_BOARD_DVBSKY_T980C] = { > + .name = "DVBSky T980C", > + .portb = CX23885_MPEG_DVB, > + }, > }; > const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards); > > @@ -939,6 +943,10 @@ struct cx23885_subid cx23885_subids[] = { > .subvendor = 0x4254, > .subdevice = 0x9580, > .card = CX23885_BOARD_DVBSKY_T9580, > + }, { > + .subvendor = 0x4254, > + .subdevice = 0x980c, > + .card = CX23885_BOARD_DVBSKY_T980C, > }, > }; > const unsigned int cx23885_idcount = ARRAY_SIZE(cx23885_subids); > @@ -1541,6 +1549,36 @@ void cx23885_gpio_setup(struct cx23885_dev *dev) > mdelay(100); > cx23885_gpio_set(dev, GPIO_2 | GPIO_11); > break; > + case CX23885_BOARD_DVBSKY_T980C: > + /* > + * GPIO-0 INTA from CiMax, input > + * GPIO-1 reset CiMax, output, high active > + * GPIO-2 reset demod, output, low active > + * GPIO-3 to GPIO-10 data/addr for CAM > + * GPIO-11 ~CS0 to CiMax1 > + * GPIO-12 ~CS1 to CiMax2 > + * GPIO-13 ADL0 load LSB addr > + * GPIO-14 ADL1 load MSB addr > + * GPIO-15 ~RDY from CiMax > + * GPIO-17 ~RD to CiMax > + * GPIO-18 ~WR to CiMax > + */ > + > + cx_set(GP0_IO, 0x00060002); /* GPIO 1/2 as output */ > + cx_clear(GP0_IO, 0x00010004); /* GPIO 0 as input */ > + mdelay(100); /* reset delay */ > + cx_set(GP0_IO, 0x00060004); /* GPIO as out, reset high */ > + cx_clear(GP0_IO, 0x00010002); > + cx_write(MC417_CTL, 0x00000037); /* enable GPIO3-18 pins */ > + > + /* GPIO-15 IN as ~ACK, rest as OUT */ > + cx_write(MC417_OEN, 0x00001000); > + > + /* ~RD, ~WR high; ADL0, ADL1 low; ~CS0, ~CS1 high */ > + cx_write(MC417_RWD, 0x0000c300); > + > + /* enable irq */ > + cx_write(GPIO_ISM, 0x00000000); /* INTERRUPTS active low */ > } > } > > @@ -1817,6 +1855,7 @@ void cx23885_card_setup(struct cx23885_dev *dev) > case CX23885_BOARD_TEVII_S471: > case CX23885_BOARD_DVBWORLD_2005: > case CX23885_BOARD_PROF_8000: > + case CX23885_BOARD_DVBSKY_T980C: > ts1->gen_ctrl_val = 0x5; /* Parallel */ > ts1->ts_clk_en_val = 0x1; /* Enable TS_CLK */ > ts1->src_sel_val = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO; > @@ -1935,6 +1974,7 @@ void cx23885_card_setup(struct cx23885_dev *dev) > case CX23885_BOARD_TBS_6980: > case CX23885_BOARD_TBS_6981: > case CX23885_BOARD_DVBSKY_T9580: > + case CX23885_BOARD_DVBSKY_T980C: > dev->sd_cx25840 = v4l2_i2c_new_subdev(&dev->v4l2_dev, > &dev->i2c_bus[2].i2c_adap, > "cx25840", 0x88 >> 1, NULL); > diff --git a/drivers/media/pci/cx23885/cx23885-dvb.c b/drivers/media/pci/cx23885/cx23885-dvb.c > index 2f532c9..d327459 100644 > --- a/drivers/media/pci/cx23885/cx23885-dvb.c > +++ b/drivers/media/pci/cx23885/cx23885-dvb.c > @@ -1681,6 +1681,52 @@ static int dvb_register(struct cx23885_tsport *port) > break; > } > break; > + case CX23885_BOARD_DVBSKY_T980C: > + i2c_bus = &dev->i2c_bus[1]; > + > + /* attach frontend */ > + memset(&si2168_config, 0, sizeof(si2168_config)); > + si2168_config.i2c_adapter = &adapter; > + si2168_config.fe = &fe0->dvb.frontend; > + si2168_config.ts_mode = SI2168_TS_PARALLEL; > + memset(&info, 0, sizeof(struct i2c_board_info)); > + strlcpy(info.type, "si2168", I2C_NAME_SIZE); > + info.addr = 0x64; > + info.platform_data = &si2168_config; > + request_module(info.type); > + client_demod = i2c_new_device(&i2c_bus->i2c_adap, &info); > + if (client_demod == NULL || > + client_demod->dev.driver == NULL) > + goto frontend_detach; > + if (!try_module_get(client_demod->dev.driver->owner)) { > + i2c_unregister_device(client_demod); > + goto frontend_detach; > + } > + port->i2c_client_demod = client_demod; > + > + /* attach tuner */ > + memset(&si2157_config, 0, sizeof(si2157_config)); > + si2157_config.fe = fe0->dvb.frontend; > + memset(&info, 0, sizeof(struct i2c_board_info)); > + strlcpy(info.type, "si2157", I2C_NAME_SIZE); > + info.addr = 0x60; > + info.platform_data = &si2157_config; > + request_module(info.type); > + client_tuner = i2c_new_device(adapter, &info); > + if (client_tuner == NULL || > + client_tuner->dev.driver == NULL) { > + module_put(client_demod->dev.driver->owner); > + i2c_unregister_device(client_demod); > + goto frontend_detach; > + } > + if (!try_module_get(client_tuner->dev.driver->owner)) { > + i2c_unregister_device(client_tuner); > + module_put(client_demod->dev.driver->owner); > + i2c_unregister_device(client_demod); > + goto frontend_detach; > + } > + port->i2c_client_tuner = client_tuner; > + break; > default: > printk(KERN_INFO "%s: The frontend of your DVB/ATSC card " > " isn't supported yet\n", > @@ -1771,6 +1817,21 @@ static int dvb_register(struct cx23885_tsport *port) > (port->nr-1) * 8, 6); > break; > } > + case CX23885_BOARD_DVBSKY_T980C: { > + u8 eeprom[256]; /* 24C02 i2c eeprom */ > + > + if (port->nr != 1) > + break; > + > + /* Read entire EEPROM */ > + dev->i2c_bus[0].i2c_client.addr = 0xa0 >> 1; > + tveeprom_read(&dev->i2c_bus[0].i2c_client, eeprom, > + sizeof(eeprom)); > + printk(KERN_INFO "DVBSky T980C MAC address: %pM\n", > + eeprom + 0xc0); > + memcpy(port->frontends.adapter.proposed_mac, eeprom + 0xc0, 6); > + break; > + } > } > > return ret; > diff --git a/drivers/media/pci/cx23885/cx23885.h b/drivers/media/pci/cx23885/cx23885.h > index 06088a0..1792d1a 100644 > --- a/drivers/media/pci/cx23885/cx23885.h > +++ b/drivers/media/pci/cx23885/cx23885.h > @@ -93,6 +93,7 @@ > #define CX23885_BOARD_HAUPPAUGE_IMPACTVCBE 43 > #define CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2 44 > #define CX23885_BOARD_DVBSKY_T9580 45 > +#define CX23885_BOARD_DVBSKY_T980C 46 > > #define GPIO_0 0x00000001 > #define GPIO_1 0x00000002 >
diff --git a/drivers/media/pci/cx23885/cx23885-cards.c b/drivers/media/pci/cx23885/cx23885-cards.c index 88c257d..e8965e6 100644 --- a/drivers/media/pci/cx23885/cx23885-cards.c +++ b/drivers/media/pci/cx23885/cx23885-cards.c @@ -680,6 +680,10 @@ struct cx23885_board cx23885_boards[] = { .portb = CX23885_MPEG_DVB, .portc = CX23885_MPEG_DVB, }, + [CX23885_BOARD_DVBSKY_T980C] = { + .name = "DVBSky T980C", + .portb = CX23885_MPEG_DVB, + }, }; const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards); @@ -939,6 +943,10 @@ struct cx23885_subid cx23885_subids[] = { .subvendor = 0x4254, .subdevice = 0x9580, .card = CX23885_BOARD_DVBSKY_T9580, + }, { + .subvendor = 0x4254, + .subdevice = 0x980c, + .card = CX23885_BOARD_DVBSKY_T980C, }, }; const unsigned int cx23885_idcount = ARRAY_SIZE(cx23885_subids); @@ -1541,6 +1549,36 @@ void cx23885_gpio_setup(struct cx23885_dev *dev) mdelay(100); cx23885_gpio_set(dev, GPIO_2 | GPIO_11); break; + case CX23885_BOARD_DVBSKY_T980C: + /* + * GPIO-0 INTA from CiMax, input + * GPIO-1 reset CiMax, output, high active + * GPIO-2 reset demod, output, low active + * GPIO-3 to GPIO-10 data/addr for CAM + * GPIO-11 ~CS0 to CiMax1 + * GPIO-12 ~CS1 to CiMax2 + * GPIO-13 ADL0 load LSB addr + * GPIO-14 ADL1 load MSB addr + * GPIO-15 ~RDY from CiMax + * GPIO-17 ~RD to CiMax + * GPIO-18 ~WR to CiMax + */ + + cx_set(GP0_IO, 0x00060002); /* GPIO 1/2 as output */ + cx_clear(GP0_IO, 0x00010004); /* GPIO 0 as input */ + mdelay(100); /* reset delay */ + cx_set(GP0_IO, 0x00060004); /* GPIO as out, reset high */ + cx_clear(GP0_IO, 0x00010002); + cx_write(MC417_CTL, 0x00000037); /* enable GPIO3-18 pins */ + + /* GPIO-15 IN as ~ACK, rest as OUT */ + cx_write(MC417_OEN, 0x00001000); + + /* ~RD, ~WR high; ADL0, ADL1 low; ~CS0, ~CS1 high */ + cx_write(MC417_RWD, 0x0000c300); + + /* enable irq */ + cx_write(GPIO_ISM, 0x00000000); /* INTERRUPTS active low */ } } @@ -1817,6 +1855,7 @@ void cx23885_card_setup(struct cx23885_dev *dev) case CX23885_BOARD_TEVII_S471: case CX23885_BOARD_DVBWORLD_2005: case CX23885_BOARD_PROF_8000: + case CX23885_BOARD_DVBSKY_T980C: ts1->gen_ctrl_val = 0x5; /* Parallel */ ts1->ts_clk_en_val = 0x1; /* Enable TS_CLK */ ts1->src_sel_val = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO; @@ -1935,6 +1974,7 @@ void cx23885_card_setup(struct cx23885_dev *dev) case CX23885_BOARD_TBS_6980: case CX23885_BOARD_TBS_6981: case CX23885_BOARD_DVBSKY_T9580: + case CX23885_BOARD_DVBSKY_T980C: dev->sd_cx25840 = v4l2_i2c_new_subdev(&dev->v4l2_dev, &dev->i2c_bus[2].i2c_adap, "cx25840", 0x88 >> 1, NULL); diff --git a/drivers/media/pci/cx23885/cx23885-dvb.c b/drivers/media/pci/cx23885/cx23885-dvb.c index 2f532c9..d327459 100644 --- a/drivers/media/pci/cx23885/cx23885-dvb.c +++ b/drivers/media/pci/cx23885/cx23885-dvb.c @@ -1681,6 +1681,52 @@ static int dvb_register(struct cx23885_tsport *port) break; } break; + case CX23885_BOARD_DVBSKY_T980C: + i2c_bus = &dev->i2c_bus[1]; + + /* attach frontend */ + memset(&si2168_config, 0, sizeof(si2168_config)); + si2168_config.i2c_adapter = &adapter; + si2168_config.fe = &fe0->dvb.frontend; + si2168_config.ts_mode = SI2168_TS_PARALLEL; + memset(&info, 0, sizeof(struct i2c_board_info)); + strlcpy(info.type, "si2168", I2C_NAME_SIZE); + info.addr = 0x64; + info.platform_data = &si2168_config; + request_module(info.type); + client_demod = i2c_new_device(&i2c_bus->i2c_adap, &info); + if (client_demod == NULL || + client_demod->dev.driver == NULL) + goto frontend_detach; + if (!try_module_get(client_demod->dev.driver->owner)) { + i2c_unregister_device(client_demod); + goto frontend_detach; + } + port->i2c_client_demod = client_demod; + + /* attach tuner */ + memset(&si2157_config, 0, sizeof(si2157_config)); + si2157_config.fe = fe0->dvb.frontend; + memset(&info, 0, sizeof(struct i2c_board_info)); + strlcpy(info.type, "si2157", I2C_NAME_SIZE); + info.addr = 0x60; + info.platform_data = &si2157_config; + request_module(info.type); + client_tuner = i2c_new_device(adapter, &info); + if (client_tuner == NULL || + client_tuner->dev.driver == NULL) { + module_put(client_demod->dev.driver->owner); + i2c_unregister_device(client_demod); + goto frontend_detach; + } + if (!try_module_get(client_tuner->dev.driver->owner)) { + i2c_unregister_device(client_tuner); + module_put(client_demod->dev.driver->owner); + i2c_unregister_device(client_demod); + goto frontend_detach; + } + port->i2c_client_tuner = client_tuner; + break; default: printk(KERN_INFO "%s: The frontend of your DVB/ATSC card " " isn't supported yet\n", @@ -1771,6 +1817,21 @@ static int dvb_register(struct cx23885_tsport *port) (port->nr-1) * 8, 6); break; } + case CX23885_BOARD_DVBSKY_T980C: { + u8 eeprom[256]; /* 24C02 i2c eeprom */ + + if (port->nr != 1) + break; + + /* Read entire EEPROM */ + dev->i2c_bus[0].i2c_client.addr = 0xa0 >> 1; + tveeprom_read(&dev->i2c_bus[0].i2c_client, eeprom, + sizeof(eeprom)); + printk(KERN_INFO "DVBSky T980C MAC address: %pM\n", + eeprom + 0xc0); + memcpy(port->frontends.adapter.proposed_mac, eeprom + 0xc0, 6); + break; + } } return ret; diff --git a/drivers/media/pci/cx23885/cx23885.h b/drivers/media/pci/cx23885/cx23885.h index 06088a0..1792d1a 100644 --- a/drivers/media/pci/cx23885/cx23885.h +++ b/drivers/media/pci/cx23885/cx23885.h @@ -93,6 +93,7 @@ #define CX23885_BOARD_HAUPPAUGE_IMPACTVCBE 43 #define CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP2 44 #define CX23885_BOARD_DVBSKY_T9580 45 +#define CX23885_BOARD_DVBSKY_T980C 46 #define GPIO_0 0x00000001 #define GPIO_1 0x00000002
This patch adds basic support for DVBSky T980C card. CI interface is not supported. DVBSky T980C is a PCIe card with the following components: - CX23885 PCIe bridge - Si2168-A20 demodulator - Si2158-A20 tuner - CIMaX SP2 CI chip The demodulator and tuner need firmware. They're the same as used with TT CT2-4650 CI: https://www.mail-archive.com/linux-media@vger.kernel.org/msg78033.html Signed-off-by: Olli Salonen <olli.salonen@iki.fi> --- drivers/media/pci/cx23885/cx23885-cards.c | 40 ++++++++++++++++++++ drivers/media/pci/cx23885/cx23885-dvb.c | 61 +++++++++++++++++++++++++++++++ drivers/media/pci/cx23885/cx23885.h | 1 + 3 files changed, 102 insertions(+)