| Message ID | 1411937610-22125-2-git-send-email-suravee.suthikulpanit@amd.com (mailing list archive) |
|---|---|
| State | New, archived |
| Delegated to: | Bjorn Helgaas |
| Headers | show |
Hi Suravee, On Sun, Sep 28, 2014 at 09:53:27PM +0100, suravee.suthikulpanit@amd.com wrote: > From: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> > > Initial revision of device tree for AMD Seattle platform To check: how is it possible to make use of a DTB generated from this dts? Can a user update the DTB used by the Seattle firmware? > > Cc: Rob Herring <robh+dt@kernel.org> > Cc: Mark Rutland <mark.rutland@arm.com> > Cc: Will Deacon <will.deacon@arm.com> > Cc: Catalin Marinas <catalin.marinas@arm.com> > Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> > Signed-off-by: Thomas Lendacky <Thomas.Lendacky@amd.com> > Signed-off-by: Joel Schopp <Joel.Schopp@amd.com> > --- > arch/arm64/boot/dts/Makefile | 1 + > arch/arm64/boot/dts/amd-seattle-periph.dtsi | 175 ++++++++++++++++++++ > arch/arm64/boot/dts/amd-seattle.dts | 245 ++++++++++++++++++++++++++++ > 3 files changed, 421 insertions(+) > create mode 100644 arch/arm64/boot/dts/amd-seattle-periph.dtsi > create mode 100644 arch/arm64/boot/dts/amd-seattle.dts > > diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile > index c52bdb0..11cb2e3 100644 > --- a/arch/arm64/boot/dts/Makefile > +++ b/arch/arm64/boot/dts/Makefile > @@ -1,5 +1,6 @@ > dtb-$(CONFIG_ARCH_VEXPRESS) += rtsm_ve-aemv8a.dtb foundation-v8.dtb > dtb-$(CONFIG_ARCH_XGENE) += apm-mustang.dtb > +dtb-$(CONFIG_ARCH_SEATTLE) += amd-seattle.dtb > > targets += dtbs > targets += $(dtb-y) > diff --git a/arch/arm64/boot/dts/amd-seattle-periph.dtsi b/arch/arm64/boot/dts/amd-seattle-periph.dtsi > new file mode 100644 > index 0000000..e5bcf1c > --- /dev/null > +++ b/arch/arm64/boot/dts/amd-seattle-periph.dtsi > @@ -0,0 +1,175 @@ > +/* > + * DTS file for AMD Seattle Peripheral > + * > + * Copyright (C) 2014 Advanced Micro Devices, Inc. > + */ > + > +motherboard { > + arm,v2m-memory-map = "rs1"; > + compatible = "arm,vexpress,v2m-p1", "simple-bus"; The v2m stuff above can go. This isn't a versatile express, and we won't use those properties anyway. > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + adl3clk_100mhz: clk100mhz_0 { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <100000000>; > + clock-output-names = "adl3clk_100mhz"; > + }; > + > + ccpclk_375mhz: clk375mhz { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <375000000>; > + clock-output-names = "ccpclk_375mhz"; > + }; > + > + sataclk_333mhz: clk333mhz { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <333000000>; > + clock-output-names = "sataclk_333mhz"; > + }; > + > + pcieclk_500mhz: clk500mhz_0 { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <500000000>; > + clock-output-names = "pcieclk_500mhz"; > + }; > + > + dmaclk_500mhz: clk500mhz_1 { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <500000000>; > + clock-output-names = "dmaclk_500mhz"; > + }; > + > + miscclk_250mhz: clk250mhz_4 { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <250000000>; > + clock-output-names = "miscclk_250mhz"; > + }; > + > + uartspiclk_100mhz: clk100mhz_1 { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <100000000>; > + clock-output-names = "uartspiclk_100mhz"; > + }; > + > + dma0: dma@1,0500000 { > + compatible = "arm,pl330", "arm,primecell"; > + reg = <0 0x0500000 0 0x1000>; > + interrupts = > + <0 368 4>, > + <0 369 4>, > + <0 370 4>, > + <0 371 4>, > + <0 372 4>, > + <0 373 4>, > + <0 374 4>, > + <0 375 4>; > + clocks = <&dmaclk_500mhz>; > + clock-names = "apb_pclk"; > + #dma-cells = <1>; > + #stream-id-cells = <32>; I didn't spot an SMMU, so I think this should go. > + }; > + > + sata0: sata@1,00300000 { > + compatible = "snps,spear-ahci"; > + reg = <0 0x300000 0 0x800>; > + interrupts = <0 355 4>; > + clocks = <&sataclk_333mhz>; > + clock-names = "apb_pclk"; > + #stream-id-cells = <32>; Likewise. > + dma-coherent; > + }; > + > + i2c@1,1000000 { > + compatible = "snps,designware-i2c"; > + reg = <0 0x01000000 0 0x1000>; > + interrupts = <0 357 4>; > + clocks = <&uartspiclk_100mhz>; > + clock-names = "apb_pclk"; > + }; > + > + v2m_serial0: uart@1,1010000 { > + compatible = "arm,pl011", "arm,primecell"; > + reg = <0 0x1010000 0 0x1000>; > + interrupts = <0 328 4>; > + clocks = <&uartspiclk_100mhz>, <&uartspiclk_100mhz>; > + clock-names = "uartclk", "apb_pclk"; > + }; > + > + ssp@1,1020000 { > + #gpio-cells = <2>; > + compatible = "arm,pl022", "arm,primecell"; Please put the compatible property first in each node. > + reg = <0 0x1020000 0 0x1000>; > + spi-controller; > + interrupts = <0 330 4>; > + clocks = <&uartspiclk_100mhz>; > + clock-names = "apb_pclk"; > + }; > + > + ssp@1,1030000 { > + #gpio-cells = <2>; > + compatible = "arm,pl022", "arm,primecell"; > + reg = <0 0x1030000 0 0x1000>; > + spi-controller; > + interrupts = <0 329 4>; > + clocks = <&uartspiclk_100mhz>; > + clock-names = "apb_pclk"; > + num-cs = <1>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + sdcard@1 { > + compatible = "mmc-spi-slot"; > + reg = <0>; The unit-address should match the first reg entry. > + spi-max-frequency = <20000000>; > + pl022,hierarchy = <0>; > + pl022,interface = <0>; > + pl022,com-mode = <0x0>; > + pl022,rx-level-trig = <0>; > + pl022,tx-level-trig = <0>; > + }; > + }; > + > + gpio@1,1040000 { > + #gpio-cells = <2>; > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0x1040000 0 0x1000>; > + gpio-controller; > + interrupts = <0 359 4>; > + clocks = <&uartspiclk_100mhz>; > + clock-names = "apb_pclk"; > + }; > + > + gpio@1,1050000 { > + #gpio-cells = <2>; > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0x1050000 0 0x1000>; > + gpio-controller; > + interrupts = <0 358 4>; > + clocks = <&uartspiclk_100mhz>; > + clock-names = "apb_pclk"; > + }; > + > + timer@1,1060000 { > + compatible = "arm,standalone_a5_twd"; > + reg = <0 0x1060000 0 0x40>; > + interrupts = > + <0 378 4>, > + <0 379 4>; > + }; This binding does not exist in mainline. > + > + ccp: ccp@1,00100000 { > + compatible = "amd,ccp-seattle-v1a"; > + reg = <0 0x00100000 0 0x10000>; > + interrupts = <0 3 4>; > + dma-coherent; > + }; Nor does this. > +}; > diff --git a/arch/arm64/boot/dts/amd-seattle.dts b/arch/arm64/boot/dts/amd-seattle.dts > new file mode 100644 > index 0000000..3096d1a > --- /dev/null > +++ b/arch/arm64/boot/dts/amd-seattle.dts > @@ -0,0 +1,245 @@ > +/* > + * DTS file for AMD Seattle > + * > + * Copyright (C) 2014 Advanced Micro Devices, Inc. > + */ > + > +/dts-v1/; > + > +/ { > + compatible = "amd,seattle"; > + interrupt-parent = <&gic>; > + #address-cells = <2>; > + #size-cells = <2>; > + > + chosen { > + bootargs = "console=ttyAMA0,115200 earlycon=pl011,0xe1010000"; Please use stdout-path instead. > + linux,pci-probe-only; Why is this necessary? > + }; > + > + aliases { > + serial0 = &v2m_serial0; > + }; > + > + /* Note: This entry is modified by UEFI */ In what way is this modified? > + cpus { > + #address-cells = <2>; > + #size-cells = <0>; > + > + cpu-map { > + cluster0 { > + core0 { > + cpu = <&CPU0>; > + }; > + core1 { > + cpu = <&CPU1>; > + }; > + }; > + cluster1 { > + core0 { > + cpu = <&CPU2>; > + }; > + core1 { > + cpu = <&CPU3>; > + }; > + }; > + cluster2 { > + core0 { > + cpu = <&CPU4>; > + }; > + core1 { > + cpu = <&CPU5>; > + }; > + }; > + cluster3 { > + core0 { > + cpu = <&CPU6>; > + }; > + core1 { > + cpu = <&CPU7>; > + }; > + }; > + }; > + /* Cluster 0 Core 0 */ > + CPU0: cpu@0 { > + device_type = "cpu"; > + compatible = "arm,armv8"; Can we have the actual CPU name, please? > + reg = <0x0 0x0000>; > + enable-method = "spin-table"; > + cpu-release-addr = <0x80 0x30000050>; Not PSCI? > + }; > + > + /* Cluster 0 Core 1 */ > + CPU1: cpu@1 { > + device_type = "cpu"; > + compatible = "arm,armv8"; > + reg = <0x0 0x0001>; > + enable-method = "spin-table"; > + cpu-release-addr = <0x80 0x30000058>; At least the release addresses are unique... > + }; [...] > + > + /* Note: This entry is modified by UEFI */ > + memory@8000000000 { > + device_type = "memory"; > + reg = <0x00000080 0x00000000 0x1 0x00000000>; /* 4GB */ > + }; Why does UEFI modify this? When booted via UEFI we use the UEFI memory map. How exactly does UEFI modify this? > + > + gic: interrupt-controller@e1101000 { > + compatible = "arm,gic-400", "arm,cortex-a15-gic"; > + #interrupt-cells = <3>; > + #address-cells = <2>; > + #size-cells = <2>; > + interrupt-controller; > + ranges = <0 0 0 0xe1100000 0 0x100000>; Please keep this together with #address-cells and #size-cells. > + reg = <0x0 0xe1110000 0 0x1000>, /* gic dist */ > + <0x0 0xe112f000 0 0x2000>, /* gic cpu */ > + <0x0 0xe1140000 0 0x10000>, /* gic virtual ic*/ > + <0x0 0xe1160000 0 0x10000>; /* gic virtual cpu*/ The comments are confusing, because they don't match the architected names. I would drop them. > + interrupts = <1 8 0xf04>; > + v2m0: v2m@0x8000 { > + compatible = "arm,gic-v2m-frame"; > + msi-controller; > + arm,msi-base-spi = <64>; > + arm,msi-num-spis = <256>; > + reg = <0x0 0x80000 0 0x1000>; > + }; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <1 13 0xff01>, > + <1 14 0xff01>, > + <1 11 0xff01>, > + <1 10 0xff01>; > + }; > + > + pmu { > + compatible = "arm,armv8-pmuv3"; > + interrupts = <0 7 4>, > + <0 8 4>, > + <0 9 4>, > + <0 10 4>, > + <0 11 4>, > + <0 12 4>, > + <0 13 4>, > + <0 14 4>; > + }; > + > + /* This entry is modified by UEFI */ > + pcie0: pcie-controller{ > + compatible = "pci-host-ecam-generic"; I unfortunately don't know enough about this binding to comment. I'll leave that up to someone familiar with PCIe. > + #address-cells = <3>; > + #size-cells = <2>; > + device_type = "pci"; > + bus-range = <0 0xff>; > + reg = <0 0xf0000000 0 0x10000000>; > + dma-coherent; > + msi-parent = <&v2m0>; > + > + interrupts = > + <0 320 4>, /* ioc_soc_serr */ > + <0 321 4>; /* ioc_soc_sci */ > + > + ranges = < > + /* I/O Memory (size=64K) */ > + 0x01000000 0x00 0xefff0000 0x00 0xefff0000 0x00 0x00010000 However, please bracket list entries individually. Thanks, Mark. -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 10/10/2014 8:45 AM, Mark Rutland wrote: > Hi Suravee, > > On Sun, Sep 28, 2014 at 09:53:27PM +0100, suravee.suthikulpanit@amd.com wrote: >> From: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> >> >> Initial revision of device tree for AMD Seattle platform > > To check: how is it possible to make use of a DTB generated from this > dts? Can a user update the DTB used by the Seattle firmware? In the current FW, there is a mechanism that users can modify and provide UEFI with the updated device tree to override the one that comes with Seattle firmware. [...]; >> + >> + timer@1,1060000 { >> + compatible = "arm,standalone_a5_twd"; >> + reg = <0 0x1060000 0 0x40>; >> + interrupts = >> + <0 378 4>, >> + <0 379 4>; >> + }; > > This binding does not exist in mainline. I am removing this. > >> + >> + ccp: ccp@1,00100000 { >> + compatible = "amd,ccp-seattle-v1a"; >> + reg = <0 0x00100000 0 0x10000>; >> + interrupts = <0 3 4>; >> + dma-coherent; >> + }; > > Nor does this. The binding for this one is here (http://lxr.free-electrons.com/source/Documentation/devicetree/bindings/crypto/amd-ccp.txt). > [....] > >> + linux,pci-probe-only; > > Why is this necessary? This was defined in the PCI Generic Host Controller binding here (http://lxr.free-electrons.com/source/Documentation/devicetree/bindings/pci/host-generic-pci.txt). > >> + }; >> + >> + aliases { >> + serial0 = &v2m_serial0; >> + }; >> + >> + /* Note: This entry is modified by UEFI */ > > In what way is this modified? 1. UEFI would basically take out certain CPUs and modify the cpu-map accordingly. 2. Change method to psci-0.2 when support is in place. 3. Update release address. Actually, the "cpus" entry should/will be fully auto generated by UEFI in the future BIOS. I think I'll be taking this out completely for now. > [...] > >> + >> + /* Note: This entry is modified by UEFI */ >> + memory@8000000000 { >> + device_type = "memory"; >> + reg = <0x00000080 0x00000000 0x1 0x00000000>; /* 4GB */ >> + }; > > Why does UEFI modify this? When booted via UEFI we use the UEFI memory > map. True. But for non-EFI boot (as fallback), we still need this. UEFI will update the amount of detected memory. Actually, same here as the "cpus", this entry should/will go away completely from the static DT, and UEFI will auto-generate this in the future firmware. Thanks, Suravee -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile index c52bdb0..11cb2e3 100644 --- a/arch/arm64/boot/dts/Makefile +++ b/arch/arm64/boot/dts/Makefile @@ -1,5 +1,6 @@ dtb-$(CONFIG_ARCH_VEXPRESS) += rtsm_ve-aemv8a.dtb foundation-v8.dtb dtb-$(CONFIG_ARCH_XGENE) += apm-mustang.dtb +dtb-$(CONFIG_ARCH_SEATTLE) += amd-seattle.dtb targets += dtbs targets += $(dtb-y) diff --git a/arch/arm64/boot/dts/amd-seattle-periph.dtsi b/arch/arm64/boot/dts/amd-seattle-periph.dtsi new file mode 100644 index 0000000..e5bcf1c --- /dev/null +++ b/arch/arm64/boot/dts/amd-seattle-periph.dtsi @@ -0,0 +1,175 @@ +/* + * DTS file for AMD Seattle Peripheral + * + * Copyright (C) 2014 Advanced Micro Devices, Inc. + */ + +motherboard { + arm,v2m-memory-map = "rs1"; + compatible = "arm,vexpress,v2m-p1", "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + adl3clk_100mhz: clk100mhz_0 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "adl3clk_100mhz"; + }; + + ccpclk_375mhz: clk375mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <375000000>; + clock-output-names = "ccpclk_375mhz"; + }; + + sataclk_333mhz: clk333mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <333000000>; + clock-output-names = "sataclk_333mhz"; + }; + + pcieclk_500mhz: clk500mhz_0 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <500000000>; + clock-output-names = "pcieclk_500mhz"; + }; + + dmaclk_500mhz: clk500mhz_1 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <500000000>; + clock-output-names = "dmaclk_500mhz"; + }; + + miscclk_250mhz: clk250mhz_4 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <250000000>; + clock-output-names = "miscclk_250mhz"; + }; + + uartspiclk_100mhz: clk100mhz_1 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "uartspiclk_100mhz"; + }; + + dma0: dma@1,0500000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0 0x0500000 0 0x1000>; + interrupts = + <0 368 4>, + <0 369 4>, + <0 370 4>, + <0 371 4>, + <0 372 4>, + <0 373 4>, + <0 374 4>, + <0 375 4>; + clocks = <&dmaclk_500mhz>; + clock-names = "apb_pclk"; + #dma-cells = <1>; + #stream-id-cells = <32>; + }; + + sata0: sata@1,00300000 { + compatible = "snps,spear-ahci"; + reg = <0 0x300000 0 0x800>; + interrupts = <0 355 4>; + clocks = <&sataclk_333mhz>; + clock-names = "apb_pclk"; + #stream-id-cells = <32>; + dma-coherent; + }; + + i2c@1,1000000 { + compatible = "snps,designware-i2c"; + reg = <0 0x01000000 0 0x1000>; + interrupts = <0 357 4>; + clocks = <&uartspiclk_100mhz>; + clock-names = "apb_pclk"; + }; + + v2m_serial0: uart@1,1010000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0 0x1010000 0 0x1000>; + interrupts = <0 328 4>; + clocks = <&uartspiclk_100mhz>, <&uartspiclk_100mhz>; + clock-names = "uartclk", "apb_pclk"; + }; + + ssp@1,1020000 { + #gpio-cells = <2>; + compatible = "arm,pl022", "arm,primecell"; + reg = <0 0x1020000 0 0x1000>; + spi-controller; + interrupts = <0 330 4>; + clocks = <&uartspiclk_100mhz>; + clock-names = "apb_pclk"; + }; + + ssp@1,1030000 { + #gpio-cells = <2>; + compatible = "arm,pl022", "arm,primecell"; + reg = <0 0x1030000 0 0x1000>; + spi-controller; + interrupts = <0 329 4>; + clocks = <&uartspiclk_100mhz>; + clock-names = "apb_pclk"; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + + sdcard@1 { + compatible = "mmc-spi-slot"; + reg = <0>; + spi-max-frequency = <20000000>; + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,com-mode = <0x0>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + }; + }; + + gpio@1,1040000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0x1040000 0 0x1000>; + gpio-controller; + interrupts = <0 359 4>; + clocks = <&uartspiclk_100mhz>; + clock-names = "apb_pclk"; + }; + + gpio@1,1050000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0x1050000 0 0x1000>; + gpio-controller; + interrupts = <0 358 4>; + clocks = <&uartspiclk_100mhz>; + clock-names = "apb_pclk"; + }; + + timer@1,1060000 { + compatible = "arm,standalone_a5_twd"; + reg = <0 0x1060000 0 0x40>; + interrupts = + <0 378 4>, + <0 379 4>; + }; + + ccp: ccp@1,00100000 { + compatible = "amd,ccp-seattle-v1a"; + reg = <0 0x00100000 0 0x10000>; + interrupts = <0 3 4>; + dma-coherent; + }; +}; diff --git a/arch/arm64/boot/dts/amd-seattle.dts b/arch/arm64/boot/dts/amd-seattle.dts new file mode 100644 index 0000000..3096d1a --- /dev/null +++ b/arch/arm64/boot/dts/amd-seattle.dts @@ -0,0 +1,245 @@ +/* + * DTS file for AMD Seattle + * + * Copyright (C) 2014 Advanced Micro Devices, Inc. + */ + +/dts-v1/; + +/ { + compatible = "amd,seattle"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + chosen { + bootargs = "console=ttyAMA0,115200 earlycon=pl011,0xe1010000"; + linux,pci-probe-only; + }; + + aliases { + serial0 = &v2m_serial0; + }; + + /* Note: This entry is modified by UEFI */ + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + core1 { + cpu = <&CPU1>; + }; + }; + cluster1 { + core0 { + cpu = <&CPU2>; + }; + core1 { + cpu = <&CPU3>; + }; + }; + cluster2 { + core0 { + cpu = <&CPU4>; + }; + core1 { + cpu = <&CPU5>; + }; + }; + cluster3 { + core0 { + cpu = <&CPU6>; + }; + core1 { + cpu = <&CPU7>; + }; + }; + }; + /* Cluster 0 Core 0 */ + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x0000>; + enable-method = "spin-table"; + cpu-release-addr = <0x80 0x30000050>; + }; + + /* Cluster 0 Core 1 */ + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x0001>; + enable-method = "spin-table"; + cpu-release-addr = <0x80 0x30000058>; + }; + + /* Cluster 1 Core 0 */ + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x0100>; + enable-method = "spin-table"; + cpu-release-addr = <0x80 0x30000060>; + }; + + /* Cluster 1 Core 1 */ + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x0101>; + enable-method = "spin-table"; + cpu-release-addr = <0x80 0x30000068>; + }; + + /* Cluster 2 Core 0 */ + CPU4: cpu@4 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x0200>; + enable-method = "spin-table"; + cpu-release-addr = <0x80 0x30000070>; + }; + + /* Cluster 2 Core 1 */ + CPU5: cpu@5 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x0201>; + enable-method = "spin-table"; + cpu-release-addr = <0x80 0x30000078>; + }; + + /* Cluster 3 Core 0 */ + CPU6: cpu@6 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x0300>; + enable-method = "spin-table"; + cpu-release-addr = <0x80 0x30000080>; + }; + + /* Cluster 3 Core 1 */ + CPU7: cpu@7 { + device_type = "cpu"; + compatible = "arm,armv8"; + reg = <0x0 0x0301>; + enable-method = "spin-table"; + cpu-release-addr = <0x80 0x30000088>; + }; + }; + + /* Note: This entry is modified by UEFI */ + memory@8000000000 { + device_type = "memory"; + reg = <0x00000080 0x00000000 0x1 0x00000000>; /* 4GB */ + }; + + gic: interrupt-controller@e1101000 { + compatible = "arm,gic-400", "arm,cortex-a15-gic"; + #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + interrupt-controller; + ranges = <0 0 0 0xe1100000 0 0x100000>; + reg = <0x0 0xe1110000 0 0x1000>, /* gic dist */ + <0x0 0xe112f000 0 0x2000>, /* gic cpu */ + <0x0 0xe1140000 0 0x10000>, /* gic virtual ic*/ + <0x0 0xe1160000 0 0x10000>; /* gic virtual cpu*/ + interrupts = <1 8 0xf04>; + v2m0: v2m@0x8000 { + compatible = "arm,gic-v2m-frame"; + msi-controller; + arm,msi-base-spi = <64>; + arm,msi-num-spis = <256>; + reg = <0x0 0x80000 0 0x1000>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <1 13 0xff01>, + <1 14 0xff01>, + <1 11 0xff01>, + <1 10 0xff01>; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <0 7 4>, + <0 8 4>, + <0 9 4>, + <0 10 4>, + <0 11 4>, + <0 12 4>, + <0 13 4>, + <0 14 4>; + }; + + /* This entry is modified by UEFI */ + pcie0: pcie-controller{ + compatible = "pci-host-ecam-generic"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + bus-range = <0 0xff>; + reg = <0 0xf0000000 0 0x10000000>; + dma-coherent; + msi-parent = <&v2m0>; + + interrupts = + <0 320 4>, /* ioc_soc_serr */ + <0 321 4>; /* ioc_soc_sci */ + + ranges = < + /* I/O Memory (size=64K) */ + 0x01000000 0x00 0xefff0000 0x00 0xefff0000 0x00 0x00010000 + + /* Non-Pref 32-bit MMIO (size=512M) */ + 0x02000000 0x00 0x40000000 0x00 0x40000000 0x00 0x20000000 + + /* Non-Pref 32-bit MMIO (size=512M) */ + 0x02000000 0x00 0x60000000 0x00 0x60000000 0x00 0x20000000 + + /* Non-Pref 32-bit MMIO (size=512M) */ + 0x02000000 0x00 0x80000000 0x00 0x80000000 0x00 0x20000000 + + /* Non-Pref 32-bit MMIO (size=512M) */ + 0x02000000 0x00 0xa0000000 0x00 0xa0000000 0x00 0x20000000 + + /* Pref 64-bit MMIO (size= 4G) */ + 0x43000000 0x01 0x00000000 0x01 0x00000000 0x01 0x00000000 + + /* Pref 64-bit MMIO (size= 8G) */ + 0x43000000 0x02 0x00000000 0x02 0x00000000 0x02 0x00000000 + + /* Pref 64-bit MMIO (size=16G) */ + 0x43000000 0x04 0x00000000 0x04 0x00000000 0x04 0x00000000 + + /* Pref 64-bit MMIO (size=32G) */ + 0x43000000 0x08 0x00000000 0x08 0x00000000 0x08 0x00000000 + + /* Pref 64-bit MMIO (size=64G) */ + 0x43000000 0x10 0x00000000 0x10 0x00000000 0x10 0x00000000 + + /* Pref 64-bit MMIO (size=128G) */ + 0x43000000 0x20 0x00000000 0x20 0x00000000 0x20 0x00000000 + + /* Pref 64-bit MMIO (size=256G) */ + 0x43000000 0x40 0x00000000 0x40 0x00000000 0x40 0x00000000 + >; + }; + + smb { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0 0 0xE0000000 0 0x01300000>; + + /include/ "amd-seattle-periph.dtsi" + }; +};