| Message ID | 1415360662-30390-1-git-send-email-k.kozlowski@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Krzysztof, On 11/07/2014 08:44 PM, Krzysztof Kozlowski wrote: > The bootloader on market Rinato (Gear 2) device checks for revision in > compatible field of DTB. If it is not present or lower than required > then booting fails with: "Could not do normal boot. (no DTB found)". > > Log of bootloader in case of failure: > h/w: revision = 0x06 > h/w: schematic = SM-R380_Rev0.5_Final_0205 > date = 2000/01/01 12:00:21 (UTC) > cmu_div:4, div:5, src_clk:800000000, pixel_clk:31860720 > load_kernel: loading boot image from 57344.. (BOOT) > load_kernel: found zImage, size: 0x3267e8 > 0xbc Error! > Verify_Binary_Signature: failed. > pit_check_signature (BOOT) invalid. > load_kernel: found custom kernel (ret:-2147483647) > No need to update kernel type. > Detected board: samsung,rinato-rev06 > Could not do normal boot. (no DTB found) > : Entering usb mode for SM-R380_EUR_XX (65535).. > > Add a "rev06" suffix to compatible to satisfy the bootloader. > > Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> > --- > arch/arm/boot/dts/exynos3250-rinato.dts | 3 ++- > 1 file changed, 2 insertions(+), 1 deletion(-) > > diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts > index 84380fa13e37..f72ba0a1d915 100644 > --- a/arch/arm/boot/dts/exynos3250-rinato.dts > +++ b/arch/arm/boot/dts/exynos3250-rinato.dts > @@ -18,7 +18,8 @@ > > / { > model = "Samsung Rinato board"; > - compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3"; > + compatible = "samsung,rinato", "samsung,rinato-rev06", > + "samsung,exynos3250", "samsung,exynos3"; I think it is wrong. The released bootloader from Samsung is not u-boot. Instead, you have to update u-boot to support Exynos3250-basd Rinato board. Thanks, Chanwoo Choi -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On pi?, 2014-11-07 at 20:50 +0900, Chanwoo Choi wrote: > Hi Krzysztof, > > On 11/07/2014 08:44 PM, Krzysztof Kozlowski wrote: > > The bootloader on market Rinato (Gear 2) device checks for revision in > > compatible field of DTB. If it is not present or lower than required > > then booting fails with: "Could not do normal boot. (no DTB found)". > > > > Log of bootloader in case of failure: > > h/w: revision = 0x06 > > h/w: schematic = SM-R380_Rev0.5_Final_0205 > > date = 2000/01/01 12:00:21 (UTC) > > cmu_div:4, div:5, src_clk:800000000, pixel_clk:31860720 > > load_kernel: loading boot image from 57344.. (BOOT) > > load_kernel: found zImage, size: 0x3267e8 > > 0xbc Error! > > Verify_Binary_Signature: failed. > > pit_check_signature (BOOT) invalid. > > load_kernel: found custom kernel (ret:-2147483647) > > No need to update kernel type. > > Detected board: samsung,rinato-rev06 > > Could not do normal boot. (no DTB found) > > : Entering usb mode for SM-R380_EUR_XX (65535).. > > > > Add a "rev06" suffix to compatible to satisfy the bootloader. > > > > Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> > > --- > > arch/arm/boot/dts/exynos3250-rinato.dts | 3 ++- > > 1 file changed, 2 insertions(+), 1 deletion(-) > > > > diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts > > index 84380fa13e37..f72ba0a1d915 100644 > > --- a/arch/arm/boot/dts/exynos3250-rinato.dts > > +++ b/arch/arm/boot/dts/exynos3250-rinato.dts > > @@ -18,7 +18,8 @@ > > > > / { > > model = "Samsung Rinato board"; > > - compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3"; > > + compatible = "samsung,rinato", "samsung,rinato-rev06", > > + "samsung,exynos3250", "samsung,exynos3"; > > I think it is wrong. The released bootloader from Samsung is not u-boot. > Instead, you have to update u-boot to support Exynos3250-basd Rinato board. The bootloader on device also was not a u-boot. So the fix is for native bootloader delivered on device. I do not insist that this is proper fix. It was just needed to boot the device with custom kernel. Anyway, thanks for comments! Best regards, Krzysztof -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Krzysztof Kozlowski wrote: > > On pi?, 2014-11-07 at 20:50 +0900, Chanwoo Choi wrote: > > Hi Krzysztof, > > > > On 11/07/2014 08:44 PM, Krzysztof Kozlowski wrote: > > > The bootloader on market Rinato (Gear 2) device checks for revision in > > > compatible field of DTB. If it is not present or lower than required > > > then booting fails with: "Could not do normal boot. (no DTB found)". > > > > > > Log of bootloader in case of failure: > > > h/w: revision = 0x06 > > > h/w: schematic = SM-R380_Rev0.5_Final_0205 > > > date = 2000/01/01 12:00:21 (UTC) > > > cmu_div:4, div:5, src_clk:800000000, pixel_clk:31860720 > > > load_kernel: loading boot image from 57344.. (BOOT) > > > load_kernel: found zImage, size: 0x3267e8 > > > 0xbc Error! > > > Verify_Binary_Signature: failed. > > > pit_check_signature (BOOT) invalid. > > > load_kernel: found custom kernel (ret:-2147483647) > > > No need to update kernel type. > > > Detected board: samsung,rinato-rev06 > > > Could not do normal boot. (no DTB found) > > > : Entering usb mode for SM-R380_EUR_XX (65535).. > > > > > > Add a "rev06" suffix to compatible to satisfy the bootloader. > > > > > > Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> > > > --- > > > arch/arm/boot/dts/exynos3250-rinato.dts | 3 ++- > > > 1 file changed, 2 insertions(+), 1 deletion(-) > > > > > > diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts > > > index 84380fa13e37..f72ba0a1d915 100644 > > > --- a/arch/arm/boot/dts/exynos3250-rinato.dts > > > +++ b/arch/arm/boot/dts/exynos3250-rinato.dts > > > @@ -18,7 +18,8 @@ > > > > > > / { > > > model = "Samsung Rinato board"; > > > - compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3"; > > > + compatible = "samsung,rinato", "samsung,rinato-rev06", > > > + "samsung,exynos3250", "samsung,exynos3"; > > > > I think it is wrong. The released bootloader from Samsung is not u-boot. > > Instead, you have to update u-boot to support Exynos3250-basd Rinato board. > > The bootloader on device also was not a u-boot. So the fix is for native > bootloader delivered on device. > > I do not insist that this is proper fix. It was just needed to boot the > device with custom kernel. > > Anyway, thanks for comments! > Hi Krzysztof and Chanwoo, So, we don’t need this to fix the problem Krzysztof said? OK. - Kukjin -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Dear Kukjin, On 11/08/2014 07:16 PM, Kukjin Kim wrote: > Krzysztof Kozlowski wrote: >> >> On pi?, 2014-11-07 at 20:50 +0900, Chanwoo Choi wrote: >>> Hi Krzysztof, >>> >>> On 11/07/2014 08:44 PM, Krzysztof Kozlowski wrote: >>>> The bootloader on market Rinato (Gear 2) device checks for revision in >>>> compatible field of DTB. If it is not present or lower than required >>>> then booting fails with: "Could not do normal boot. (no DTB found)". >>>> >>>> Log of bootloader in case of failure: >>>> h/w: revision = 0x06 >>>> h/w: schematic = SM-R380_Rev0.5_Final_0205 >>>> date = 2000/01/01 12:00:21 (UTC) >>>> cmu_div:4, div:5, src_clk:800000000, pixel_clk:31860720 >>>> load_kernel: loading boot image from 57344.. (BOOT) >>>> load_kernel: found zImage, size: 0x3267e8 >>>> 0xbc Error! >>>> Verify_Binary_Signature: failed. >>>> pit_check_signature (BOOT) invalid. >>>> load_kernel: found custom kernel (ret:-2147483647) >>>> No need to update kernel type. >>>> Detected board: samsung,rinato-rev06 >>>> Could not do normal boot. (no DTB found) >>>> : Entering usb mode for SM-R380_EUR_XX (65535).. >>>> >>>> Add a "rev06" suffix to compatible to satisfy the bootloader. >>>> >>>> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> >>>> --- >>>> arch/arm/boot/dts/exynos3250-rinato.dts | 3 ++- >>>> 1 file changed, 2 insertions(+), 1 deletion(-) >>>> >>>> diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts >>>> index 84380fa13e37..f72ba0a1d915 100644 >>>> --- a/arch/arm/boot/dts/exynos3250-rinato.dts >>>> +++ b/arch/arm/boot/dts/exynos3250-rinato.dts >>>> @@ -18,7 +18,8 @@ >>>> >>>> / { >>>> model = "Samsung Rinato board"; >>>> - compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3"; >>>> + compatible = "samsung,rinato", "samsung,rinato-rev06", >>>> + "samsung,exynos3250", "samsung,exynos3"; >>> >>> I think it is wrong. The released bootloader from Samsung is not u-boot. >>> Instead, you have to update u-boot to support Exynos3250-basd Rinato board. >> >> The bootloader on device also was not a u-boot. So the fix is for native >> bootloader delivered on device. >> >> I do not insist that this is proper fix. It was just needed to boot the >> device with custom kernel. >> >> Anyway, thanks for comments! >> > Hi Krzysztof and Chanwoo, > > So, we don’t need this to fix the problem Krzysztof said? OK. Yes. The released bootloader from Samsung is not general and not opened. We have to support Exynos3250-based Rinato on general bootloader. Beset Regards, Chanwoo Choi -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts index 84380fa13e37..f72ba0a1d915 100644 --- a/arch/arm/boot/dts/exynos3250-rinato.dts +++ b/arch/arm/boot/dts/exynos3250-rinato.dts @@ -18,7 +18,8 @@ / { model = "Samsung Rinato board"; - compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3"; + compatible = "samsung,rinato", "samsung,rinato-rev06", + "samsung,exynos3250", "samsung,exynos3"; aliases { i2c7 = &i2c_max77836;
The bootloader on market Rinato (Gear 2) device checks for revision in compatible field of DTB. If it is not present or lower than required then booting fails with: "Could not do normal boot. (no DTB found)". Log of bootloader in case of failure: h/w: revision = 0x06 h/w: schematic = SM-R380_Rev0.5_Final_0205 date = 2000/01/01 12:00:21 (UTC) cmu_div:4, div:5, src_clk:800000000, pixel_clk:31860720 load_kernel: loading boot image from 57344.. (BOOT) load_kernel: found zImage, size: 0x3267e8 0xbc Error! Verify_Binary_Signature: failed. pit_check_signature (BOOT) invalid. load_kernel: found custom kernel (ret:-2147483647) No need to update kernel type. Detected board: samsung,rinato-rev06 Could not do normal boot. (no DTB found) : Entering usb mode for SM-R380_EUR_XX (65535).. Add a "rev06" suffix to compatible to satisfy the bootloader. Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> --- arch/arm/boot/dts/exynos3250-rinato.dts | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)