new file mode 100644
@@ -0,0 +1,97 @@
+== Amlogic Meson pinmux controller ==
+
+Required properties for the root node:
+ - compatible: "amlogic,meson8-pinctrl"
+ - reg: address and size of registers controlling irq functionality
+
+=== GPIO sub-nodes ===
+
+The 2 power domains of the controller (regular and always-on) are
+represented as sub-nodes and each of them acts as a GPIO controller.
+
+Required properties for sub-nodes are:
+ - reg: should contain address and size for mux, pull-enable, pull and
+ gpio register sets
+ - reg-names: an array of strings describing the "reg" entries. Must
+ contain "mux", "pull" and "gpio". "pull-enable" is optional and
+ when it is missing the "pull" registers are used instead
+ - gpio-controller: identifies the node as a gpio controller
+ - #gpio-cells: must be 2
+
+Valid sub-node names are:
+ - "banks" for the regular domain
+ - "ao-bank" for the always-on domain
+
+=== Other sub-nodes ===
+
+Child nodes without the "gpio-controller" represent some desired
+configuration for a pin or a group. Those nodes can be pinmux nodes or
+configuration nodes.
+
+Required properties for pinmux nodes are:
+ - groups: a list of pinmux groups. The list of all available groups
+ depends on the SoC and can be found in driver sources.
+ - function: the name of a function to activate for the specified set
+ of groups. The list of all available functions depends on the SoC
+ and can be found in driver sources.
+
+Required properties for configuration nodes:
+ - pins: a list of pin names
+
+Configuration nodes support the generic properties "bias-disable",
+"bias-pull-up" and "bias-pull-down", described in file
+pinctrl-bindings.txt
+
+=== Example ===
+
+ pinctrl: pinctrl@c1109880 {
+ compatible = "amlogic,meson8-pinctrl";
+ reg = <0xc1109880 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio: banks@c11080b0 {
+ reg = <0xc11080b0 0x28>,
+ <0xc11080e8 0x18>,
+ <0xc1108120 0x18>,
+ <0xc1108030 0x30>;
+ reg-names = "mux", "pull", "pull-enable", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpio_ao: ao-bank@c1108030 {
+ reg = <0xc8100014 0x4>,
+ <0xc810002c 0x4>,
+ <0xc8100024 0x8>;
+ reg-names = "mux", "pull", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ nand {
+ mux {
+ groups = "nand_io", "nand_io_ce0", "nand_io_ce1",
+ "nand_io_rb0", "nand_ale", "nand_cle",
+ "nand_wen_clk", "nand_ren_clk", "nand_dqs",
+ "nand_ce2", "nand_ce3";
+ function = "nand";
+ };
+ };
+
+ uart_ao_a {
+ mux {
+ groups = "uart_tx_ao_a", "uart_rx_ao_a",
+ "uart_cts_ao_a", "uart_rts_ao_a";
+ function = "uart_ao";
+ };
+
+ conf {
+ pins = "GPIOAO_0", "GPIOAO_1",
+ "GPIOAO_2", "GPIOAO_3";
+ bias-disable;
+ };
+ };
+ };
+
Add device tree bindings documentation for Amlogic Meson pin and GPIO controller. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> --- .../devicetree/bindings/pinctrl/meson,pinctrl.txt | 97 ++++++++++++++++++++++ 1 file changed, 97 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt