| Message ID | 1414588409-8065-1-git-send-email-m.szyprowski@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi, On Wed, Oct 29, 2014 at 02:13:28PM +0100, Marek Szyprowski wrote: > This patch adds a driver implementing correct reboot and poweroff > procedures for Exynos4412-based Hardkernel's Odroid X/X2/U2/U3/U3+ > boards. Sorry it took so long. I have a couple of small requests before applying this (comments inline). > Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> > --- > .../bindings/power/reset/odroid-reset.txt | 18 ++++ > drivers/power/reset/Kconfig | 6 ++ > drivers/power/reset/Makefile | 1 + > drivers/power/reset/odroid-reboot.c | 119 +++++++++++++++++++++ > 4 files changed, 144 insertions(+) > create mode 100644 Documentation/devicetree/bindings/power/reset/odroid-reset.txt > create mode 100644 drivers/power/reset/odroid-reboot.c > > diff --git a/Documentation/devicetree/bindings/power/reset/odroid-reset.txt b/Documentation/devicetree/bindings/power/reset/odroid-reset.txt > new file mode 100644 > index 000000000000..86471a463518 > --- /dev/null > +++ b/Documentation/devicetree/bindings/power/reset/odroid-reset.txt > @@ -0,0 +1,18 @@ > +* Device tree bindings for Hardkernel's Exynos4412 based Odroid boards > + > +This node is intended to allow proper system reboot and power off of > +Odroid X/X2/U2/U3/U3+ boards with eMMC storage. Without this node, board > +hangs during standard reset procedure. > + > +Required properties: > +- compatible: hardkernel,odroid-reboot > +- samsung,pmureg-phandle: phandle to Exynos PMU node > +- reset-gpios: phandle and gpio-specifier to the GPIO pin > + connected to the eMMC_nDET > + > +Example: > +odroid_reboot { > + compatible = "hardkernel,odroid-reboot"; > + samsung,pmureg-phandle = <&pmu_system_controller>; > + reset-gpio = <&gpk1 2 0>; > +}; > diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig > index f65ff49bb275..f02b13d5344f 100644 > --- a/drivers/power/reset/Kconfig > +++ b/drivers/power/reset/Kconfig > @@ -84,6 +84,12 @@ config POWER_RESET_LTC2952 > This driver supports an external powerdown trigger and board power > down via the LTC2952. Bindings are made in the device tree. > > +config POWER_RESET_ODROID > + bool "Hardkernel's Exynos4412 based Odroid reboot driver" > + depends on POWER_RESET && ARCH_EXYNOS once the arm specific restart handler is gone you can add || COMPILE_TEST > + help > + Power off and restart support for Odroid boards. > + > config POWER_RESET_QNAP > bool "QNAP power-off driver" > depends on OF_GPIO && PLAT_ORION > diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile > index 76ce1c59469b..178ee86eb813 100644 > --- a/drivers/power/reset/Makefile > +++ b/drivers/power/reset/Makefile > @@ -8,6 +8,7 @@ obj-$(CONFIG_POWER_RESET_GPIO_RESTART) += gpio-restart.o > obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o > obj-$(CONFIG_POWER_RESET_MSM) += msm-poweroff.o > obj-$(CONFIG_POWER_RESET_LTC2952) += ltc2952-poweroff.o > +obj-$(CONFIG_POWER_RESET_ODROID) += odroid-reboot.o > obj-$(CONFIG_POWER_RESET_QNAP) += qnap-poweroff.o > obj-$(CONFIG_POWER_RESET_RESTART) += restart-poweroff.o > obj-$(CONFIG_POWER_RESET_SUN6I) += sun6i-reboot.o > diff --git a/drivers/power/reset/odroid-reboot.c b/drivers/power/reset/odroid-reboot.c > new file mode 100644 > index 000000000000..823e93539220 > --- /dev/null > +++ b/drivers/power/reset/odroid-reboot.c > @@ -0,0 +1,119 @@ > +/* > + * Copyright (c) 2014 Samsung Electronics Co., Ltd. > + * http://www.samsung.com > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + */ > + > +#include <linux/delay.h> > +#include <linux/gpio.h> > +#include <linux/io.h> > +#include <linux/mfd/syscon.h> > +#include <linux/module.h> > +#include <linux/of_platform.h> > +#include <linux/of_gpio.h> > +#include <linux/reboot.h> > +#include <linux/regmap.h> > + > +#include <asm/system_misc.h> > + > +#define PS_HOLD_CONTROL 0x330C > + > +struct odroid_reboot_data { > + struct device *dev; > + int power_gpio; > + struct regmap *reg_pmu; > + void (*reboot_func)(enum reboot_mode mode, const char *cmd); > +}; > + > +static struct odroid_reboot_data *reboot_data; > + > +static void odroid_reboot(enum reboot_mode mode, const char *cmd) > +{ > + local_irq_disable(); > + > + gpio_set_value(reboot_data->power_gpio, 0); > + mdelay(150); > + gpio_set_value(reboot_data->power_gpio, 1); > + > + reboot_data->reboot_func(mode, cmd); > + > + pr_emerg("%s: waiting for reboot\n", __func__); > + while (1) > + ; > +} > + > +static void odroid_power_off(void) > +{ > + regmap_update_bits(reboot_data->reg_pmu, PS_HOLD_CONTROL, 0xffffffff, 0x5200); > + while (1) { > + pr_emerg("%s: should not reach here!\n", __func__); > + msleep(1000); > + } > +} > + > +static struct odroid_reboot_data *odroid_reboot_parse_dt(struct device *dev) > +{ > + struct device_node *np = dev->of_node; > + struct odroid_reboot_data *data; > + > + data = devm_kzalloc(dev, sizeof(struct odroid_reboot_data), GFP_KERNEL); > + if (!data) > + return NULL; > + > + data->power_gpio = of_get_named_gpio(np, "reset-gpios", 0); > + if (!gpio_is_valid(data->power_gpio)) { > + dev_err(dev, "invalid reset gpio pin\n"); > + return NULL; > + } > + devm_gpio_request(dev, data->power_gpio, "reset"); please use gpiod interface. > + > + data->reg_pmu = syscon_regmap_lookup_by_phandle(np, > + "samsung,pmureg-phandle"); > + if (IS_ERR(data->reg_pmu)) { > + dev_err(dev, "failed to map PMU registers\n"); > + return NULL; > + } > + > + return data; > +} > + > +static int odroid_reboot_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev; > + > + if (pdev->dev.of_node) > + reboot_data = odroid_reboot_parse_dt(dev); > + > + if (!reboot_data) > + return -EINVAL; > + > + reboot_data->dev = &pdev->dev; > + reboot_data->reboot_func = arm_pm_restart; > + > + /* grab reboot arm specific hook */ > + arm_pm_restart = odroid_reboot; please use register_restart_handler() and unregister_restart_handler() in remove function. > + /* register power off function */ > + pm_power_off = odroid_power_off; > + > + return 0; > +} > + > +static struct of_device_id odroid_reboot_of_match[] = { > + { .compatible = "hardkernel,odroid-reboot", }, > + { }, > +}; > + > +static struct platform_driver odroid_reboot_driver = { > + .probe = odroid_reboot_probe, > + .driver = { > + .name = "odroid-reboot", > + .owner = THIS_MODULE, Please remove .owner line (not needed, will trigger a coccinelle warning). > + .of_match_table = of_match_ptr(odroid_reboot_of_match), > + } > +}; > +module_platform_driver(odroid_reboot_driver); -- Sebastian
Hi, On 01/22/2015 10:06 AM, Sebastian Reichel wrote: > Hi, > > On Wed, Oct 29, 2014 at 02:13:28PM +0100, Marek Szyprowski wrote: >> This patch adds a driver implementing correct reboot and poweroff >> procedures for Exynos4412-based Hardkernel's Odroid X/X2/U2/U3/U3+ >> boards. > > Sorry it took so long. I have a couple of small requests before > applying this (comments inline). > >> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> >> --- >> .../bindings/power/reset/odroid-reset.txt | 18 ++++ >> drivers/power/reset/Kconfig | 6 ++ >> drivers/power/reset/Makefile | 1 + >> drivers/power/reset/odroid-reboot.c | 119 +++++++++++++++++++++ >> 4 files changed, 144 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/power/reset/odroid-reset.txt >> create mode 100644 drivers/power/reset/odroid-reboot.c >> >> diff --git a/Documentation/devicetree/bindings/power/reset/odroid-reset.txt b/Documentation/devicetree/bindings/power/reset/odroid-reset.txt >> new file mode 100644 >> index 000000000000..86471a463518 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/power/reset/odroid-reset.txt >> @@ -0,0 +1,18 @@ >> +* Device tree bindings for Hardkernel's Exynos4412 based Odroid boards >> + >> +This node is intended to allow proper system reboot and power off of >> +Odroid X/X2/U2/U3/U3+ boards with eMMC storage. Without this node, board >> +hangs during standard reset procedure. >> + >> +Required properties: >> +- compatible: hardkernel,odroid-reboot >> +- samsung,pmureg-phandle: phandle to Exynos PMU node >> +- reset-gpios: phandle and gpio-specifier to the GPIO pin >> + connected to the eMMC_nDET >> + >> +Example: >> +odroid_reboot { >> + compatible = "hardkernel,odroid-reboot"; >> + samsung,pmureg-phandle = <&pmu_system_controller>; >> + reset-gpio = <&gpk1 2 0>; >> +}; >> diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig >> index f65ff49bb275..f02b13d5344f 100644 >> --- a/drivers/power/reset/Kconfig >> +++ b/drivers/power/reset/Kconfig >> @@ -84,6 +84,12 @@ config POWER_RESET_LTC2952 >> This driver supports an external powerdown trigger and board power >> down via the LTC2952. Bindings are made in the device tree. >> >> +config POWER_RESET_ODROID >> + bool "Hardkernel's Exynos4412 based Odroid reboot driver" >> + depends on POWER_RESET && ARCH_EXYNOS > > once the arm specific restart handler is gone you can add || > COMPILE_TEST > >> + help >> + Power off and restart support for Odroid boards. >> + >> config POWER_RESET_QNAP >> bool "QNAP power-off driver" >> depends on OF_GPIO && PLAT_ORION >> diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile >> index 76ce1c59469b..178ee86eb813 100644 >> --- a/drivers/power/reset/Makefile >> +++ b/drivers/power/reset/Makefile >> @@ -8,6 +8,7 @@ obj-$(CONFIG_POWER_RESET_GPIO_RESTART) += gpio-restart.o >> obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o >> obj-$(CONFIG_POWER_RESET_MSM) += msm-poweroff.o >> obj-$(CONFIG_POWER_RESET_LTC2952) += ltc2952-poweroff.o >> +obj-$(CONFIG_POWER_RESET_ODROID) += odroid-reboot.o >> obj-$(CONFIG_POWER_RESET_QNAP) += qnap-poweroff.o >> obj-$(CONFIG_POWER_RESET_RESTART) += restart-poweroff.o >> obj-$(CONFIG_POWER_RESET_SUN6I) += sun6i-reboot.o >> diff --git a/drivers/power/reset/odroid-reboot.c b/drivers/power/reset/odroid-reboot.c >> new file mode 100644 >> index 000000000000..823e93539220 >> --- /dev/null >> +++ b/drivers/power/reset/odroid-reboot.c >> @@ -0,0 +1,119 @@ >> +/* >> + * Copyright (c) 2014 Samsung Electronics Co., Ltd. >> + * http://www.samsung.com >> + * >> + * This program is free software; you can redistribute it and/or modify >> + * it under the terms of the GNU General Public License as published by >> + * the Free Software Foundation; either version 2 of the License, or >> + * (at your option) any later version. >> + */ >> + >> +#include <linux/delay.h> >> +#include <linux/gpio.h> >> +#include <linux/io.h> >> +#include <linux/mfd/syscon.h> >> +#include <linux/module.h> >> +#include <linux/of_platform.h> >> +#include <linux/of_gpio.h> >> +#include <linux/reboot.h> >> +#include <linux/regmap.h> >> + >> +#include <asm/system_misc.h> >> + >> +#define PS_HOLD_CONTROL 0x330C >> + >> +struct odroid_reboot_data { >> + struct device *dev; >> + int power_gpio; >> + struct regmap *reg_pmu; >> + void (*reboot_func)(enum reboot_mode mode, const char *cmd); >> +}; >> + >> +static struct odroid_reboot_data *reboot_data; >> + >> +static void odroid_reboot(enum reboot_mode mode, const char *cmd) >> +{ >> + local_irq_disable(); >> + >> + gpio_set_value(reboot_data->power_gpio, 0); >> + mdelay(150); >> + gpio_set_value(reboot_data->power_gpio, 1); >> + >> + reboot_data->reboot_func(mode, cmd); >> + It is called do_kernel_restart() if arm_pm_restart is NULL from machine_restart of arch/arm/kernel/process.c How about this? if (reboot_data->reboot_func) reboot_data->reboot_func(mode, cmd); else do_kernel_restart(cmd); >> + pr_emerg("%s: waiting for reboot\n", __func__); >> + while (1) >> + ; Then this endless loop is also unnecessary. Thanks. >> +} >> + >> +static void odroid_power_off(void) >> +{ >> + regmap_update_bits(reboot_data->reg_pmu, PS_HOLD_CONTROL, 0xffffffff, 0x5200); >> + while (1) { >> + pr_emerg("%s: should not reach here!\n", __func__); >> + msleep(1000); >> + } >> +} >> + >> +static struct odroid_reboot_data *odroid_reboot_parse_dt(struct device *dev) >> +{ >> + struct device_node *np = dev->of_node; >> + struct odroid_reboot_data *data; >> + >> + data = devm_kzalloc(dev, sizeof(struct odroid_reboot_data), GFP_KERNEL); >> + if (!data) >> + return NULL; >> + >> + data->power_gpio = of_get_named_gpio(np, "reset-gpios", 0); >> + if (!gpio_is_valid(data->power_gpio)) { >> + dev_err(dev, "invalid reset gpio pin\n"); >> + return NULL; >> + } >> + devm_gpio_request(dev, data->power_gpio, "reset"); > > please use gpiod interface. > >> + >> + data->reg_pmu = syscon_regmap_lookup_by_phandle(np, >> + "samsung,pmureg-phandle"); >> + if (IS_ERR(data->reg_pmu)) { >> + dev_err(dev, "failed to map PMU registers\n"); >> + return NULL; >> + } >> + >> + return data; >> +} >> + >> +static int odroid_reboot_probe(struct platform_device *pdev) >> +{ >> + struct device *dev = &pdev->dev; >> + >> + if (pdev->dev.of_node) >> + reboot_data = odroid_reboot_parse_dt(dev); >> + >> + if (!reboot_data) >> + return -EINVAL; >> + >> + reboot_data->dev = &pdev->dev; >> + reboot_data->reboot_func = arm_pm_restart; >> + >> + /* grab reboot arm specific hook */ >> + arm_pm_restart = odroid_reboot; > > please use register_restart_handler() and > unregister_restart_handler() in remove function. > >> + /* register power off function */ >> + pm_power_off = odroid_power_off; >> + >> + return 0; >> +} >> + >> +static struct of_device_id odroid_reboot_of_match[] = { >> + { .compatible = "hardkernel,odroid-reboot", }, >> + { }, >> +}; >> + >> +static struct platform_driver odroid_reboot_driver = { >> + .probe = odroid_reboot_probe, >> + .driver = { >> + .name = "odroid-reboot", >> + .owner = THIS_MODULE, > > Please remove .owner line (not needed, will trigger a coccinelle > warning). > >> + .of_match_table = of_match_ptr(odroid_reboot_of_match), >> + } >> +}; >> +module_platform_driver(odroid_reboot_driver); > > -- Sebastian > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello, On 2015-01-22 02:33, Joonyoung Shim wrote: > On 01/22/2015 10:06 AM, Sebastian Reichel wrote: >> On Wed, Oct 29, 2014 at 02:13:28PM +0100, Marek Szyprowski wrote: >>> This patch adds a driver implementing correct reboot and poweroff >>> procedures for Exynos4412-based Hardkernel's Odroid X/X2/U2/U3/U3+ >>> boards. >> Sorry it took so long. I have a couple of small requests before >> applying this (comments inline). >> >>> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> >>> --- >>> .../bindings/power/reset/odroid-reset.txt | 18 ++++ >>> drivers/power/reset/Kconfig | 6 ++ >>> drivers/power/reset/Makefile | 1 + >>> drivers/power/reset/odroid-reboot.c | 119 +++++++++++++++++++++ >>> 4 files changed, 144 insertions(+) >>> create mode 100644 Documentation/devicetree/bindings/power/reset/odroid-reset.txt >>> create mode 100644 drivers/power/reset/odroid-reboot.c >>> >>> diff --git a/Documentation/devicetree/bindings/power/reset/odroid-reset.txt b/Documentation/devicetree/bindings/power/reset/odroid-reset.txt >>> new file mode 100644 >>> index 000000000000..86471a463518 >>> --- /dev/null >>> +++ b/Documentation/devicetree/bindings/power/reset/odroid-reset.txt >>> @@ -0,0 +1,18 @@ >>> +* Device tree bindings for Hardkernel's Exynos4412 based Odroid boards >>> + >>> +This node is intended to allow proper system reboot and power off of >>> +Odroid X/X2/U2/U3/U3+ boards with eMMC storage. Without this node, board >>> +hangs during standard reset procedure. >>> + >>> +Required properties: >>> +- compatible: hardkernel,odroid-reboot >>> +- samsung,pmureg-phandle: phandle to Exynos PMU node >>> +- reset-gpios: phandle and gpio-specifier to the GPIO pin >>> + connected to the eMMC_nDET >>> + >>> +Example: >>> +odroid_reboot { >>> + compatible = "hardkernel,odroid-reboot"; >>> + samsung,pmureg-phandle = <&pmu_system_controller>; >>> + reset-gpio = <&gpk1 2 0>; >>> +}; >>> diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig >>> index f65ff49bb275..f02b13d5344f 100644 >>> --- a/drivers/power/reset/Kconfig >>> +++ b/drivers/power/reset/Kconfig >>> @@ -84,6 +84,12 @@ config POWER_RESET_LTC2952 >>> This driver supports an external powerdown trigger and board power >>> down via the LTC2952. Bindings are made in the device tree. >>> >>> +config POWER_RESET_ODROID >>> + bool "Hardkernel's Exynos4412 based Odroid reboot driver" >>> + depends on POWER_RESET && ARCH_EXYNOS >> once the arm specific restart handler is gone you can add || >> COMPILE_TEST >> >>> + help >>> + Power off and restart support for Odroid boards. >>> + >>> config POWER_RESET_QNAP >>> bool "QNAP power-off driver" >>> depends on OF_GPIO && PLAT_ORION >>> diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile >>> index 76ce1c59469b..178ee86eb813 100644 >>> --- a/drivers/power/reset/Makefile >>> +++ b/drivers/power/reset/Makefile >>> @@ -8,6 +8,7 @@ obj-$(CONFIG_POWER_RESET_GPIO_RESTART) += gpio-restart.o >>> obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o >>> obj-$(CONFIG_POWER_RESET_MSM) += msm-poweroff.o >>> obj-$(CONFIG_POWER_RESET_LTC2952) += ltc2952-poweroff.o >>> +obj-$(CONFIG_POWER_RESET_ODROID) += odroid-reboot.o >>> obj-$(CONFIG_POWER_RESET_QNAP) += qnap-poweroff.o >>> obj-$(CONFIG_POWER_RESET_RESTART) += restart-poweroff.o >>> obj-$(CONFIG_POWER_RESET_SUN6I) += sun6i-reboot.o >>> diff --git a/drivers/power/reset/odroid-reboot.c b/drivers/power/reset/odroid-reboot.c >>> new file mode 100644 >>> index 000000000000..823e93539220 >>> --- /dev/null >>> +++ b/drivers/power/reset/odroid-reboot.c >>> @@ -0,0 +1,119 @@ >>> +/* >>> + * Copyright (c) 2014 Samsung Electronics Co., Ltd. >>> + * http://www.samsung.com >>> + * >>> + * This program is free software; you can redistribute it and/or modify >>> + * it under the terms of the GNU General Public License as published by >>> + * the Free Software Foundation; either version 2 of the License, or >>> + * (at your option) any later version. >>> + */ >>> + >>> +#include <linux/delay.h> >>> +#include <linux/gpio.h> >>> +#include <linux/io.h> >>> +#include <linux/mfd/syscon.h> >>> +#include <linux/module.h> >>> +#include <linux/of_platform.h> >>> +#include <linux/of_gpio.h> >>> +#include <linux/reboot.h> >>> +#include <linux/regmap.h> >>> + >>> +#include <asm/system_misc.h> >>> + >>> +#define PS_HOLD_CONTROL 0x330C >>> + >>> +struct odroid_reboot_data { >>> + struct device *dev; >>> + int power_gpio; >>> + struct regmap *reg_pmu; >>> + void (*reboot_func)(enum reboot_mode mode, const char *cmd); >>> +}; >>> + >>> +static struct odroid_reboot_data *reboot_data; >>> + >>> +static void odroid_reboot(enum reboot_mode mode, const char *cmd) >>> +{ >>> + local_irq_disable(); >>> + >>> + gpio_set_value(reboot_data->power_gpio, 0); >>> + mdelay(150); >>> + gpio_set_value(reboot_data->power_gpio, 1); >>> + >>> + reboot_data->reboot_func(mode, cmd); >>> + > It is called do_kernel_restart() if arm_pm_restart is NULL from > machine_restart of arch/arm/kernel/process.c > > How about this? > > if (reboot_data->reboot_func) > reboot_data->reboot_func(mode, cmd); > else > do_kernel_restart(cmd); Frankly, I analyzed this case once again and I came to conclusion that there is no need to make a separate reset driver for Odroid boards. There is nothing special, specific to whole board about this gpio. It is rather a property of MMC host controller and eMMC card that is connected to it. When only gpio toggling code is moved to reset handler registered from mmc controller, the board properly performs reboot with a generic exynos4 code. The poweroff code in above driver is just a generic Exynos4 code, so again there is no need to duplicate it. By moving the code to mmc driver, the same approach can be used for other Odroid boards (XU/XU3) and maybe even other boards which need manual resetting of eMMC cards to properly perform reboot procedure. Best regards
Hi, On Fri, Jan 23, 2015 at 12:11:22PM +0100, Marek Szyprowski wrote: > Frankly, I analyzed this case once again and I came to conclusion > that there is no need to make a separate reset driver for Odroid > boards. There is nothing special, specific to whole board about > this gpio. It is rather a property of MMC host controller and eMMC > card that is connected to it. When only gpio toggling code is > moved to reset handler registered from mmc controller, the board > properly performs reboot with a generic exynos4 code. OK, so I guess this will be fixed independently via mmc subsystem. > The poweroff code in above driver is just a generic Exynos4 code, > so again there is no need to duplicate it. OK. It seems there is a driver for that in arch/arm/mach-exynos. Otherwise I would have suggest to create something like syscon-reboot for shutdown. > By moving the code to mmc driver, the same approach can be used for other > Odroid boards (XU/XU3) and maybe even other boards which need manual > resetting of eMMC cards to properly perform reboot procedure. I suggest to start a new thread for discussing this, which includes linux-mmc. It might be interesting to provide some more details about eMMC_nDET, since MMC already contain a reset signal (which seems to be used according to the odroid schematics I found). -- Sebastian
Hello, On 2015-01-25 15:32, Sebastian Reichel wrote: > On Fri, Jan 23, 2015 at 12:11:22PM +0100, Marek Szyprowski wrote: >> Frankly, I analyzed this case once again and I came to conclusion >> that there is no need to make a separate reset driver for Odroid >> boards. There is nothing special, specific to whole board about >> this gpio. It is rather a property of MMC host controller and eMMC >> card that is connected to it. When only gpio toggling code is >> moved to reset handler registered from mmc controller, the board >> properly performs reboot with a generic exynos4 code. > OK, so I guess this will be fixed independently via mmc subsystem. I've posted an updated patch. > >> The poweroff code in above driver is just a generic Exynos4 code, >> so again there is no need to duplicate it. > OK. It seems there is a driver for that in arch/arm/mach-exynos. > Otherwise I would have suggest to create something like > syscon-reboot for shutdown. > >> By moving the code to mmc driver, the same approach can be used for other >> Odroid boards (XU/XU3) and maybe even other boards which need manual >> resetting of eMMC cards to properly perform reboot procedure. > I suggest to start a new thread for discussing this, which includes > linux-mmc. It might be interesting to provide some more details about > eMMC_nDET, since MMC already contain a reset signal (which seems to > be used according to the odroid schematics I found). My fault. The documentation for this initial driver was incorrect. The reboot fix has noting to eMMC_nDET signal. It should be eMMC nreset, which is routed directly to SoC GPIO line with external pull-up resistor. I really have no idea why I wrote eMMC_nDET instead of nreset. Best regards
diff --git a/Documentation/devicetree/bindings/power/reset/odroid-reset.txt b/Documentation/devicetree/bindings/power/reset/odroid-reset.txt new file mode 100644 index 000000000000..86471a463518 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/odroid-reset.txt @@ -0,0 +1,18 @@ +* Device tree bindings for Hardkernel's Exynos4412 based Odroid boards + +This node is intended to allow proper system reboot and power off of +Odroid X/X2/U2/U3/U3+ boards with eMMC storage. Without this node, board +hangs during standard reset procedure. + +Required properties: +- compatible: hardkernel,odroid-reboot +- samsung,pmureg-phandle: phandle to Exynos PMU node +- reset-gpios: phandle and gpio-specifier to the GPIO pin + connected to the eMMC_nDET + +Example: +odroid_reboot { + compatible = "hardkernel,odroid-reboot"; + samsung,pmureg-phandle = <&pmu_system_controller>; + reset-gpio = <&gpk1 2 0>; +}; diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig index f65ff49bb275..f02b13d5344f 100644 --- a/drivers/power/reset/Kconfig +++ b/drivers/power/reset/Kconfig @@ -84,6 +84,12 @@ config POWER_RESET_LTC2952 This driver supports an external powerdown trigger and board power down via the LTC2952. Bindings are made in the device tree. +config POWER_RESET_ODROID + bool "Hardkernel's Exynos4412 based Odroid reboot driver" + depends on POWER_RESET && ARCH_EXYNOS + help + Power off and restart support for Odroid boards. + config POWER_RESET_QNAP bool "QNAP power-off driver" depends on OF_GPIO && PLAT_ORION diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile index 76ce1c59469b..178ee86eb813 100644 --- a/drivers/power/reset/Makefile +++ b/drivers/power/reset/Makefile @@ -8,6 +8,7 @@ obj-$(CONFIG_POWER_RESET_GPIO_RESTART) += gpio-restart.o obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o obj-$(CONFIG_POWER_RESET_MSM) += msm-poweroff.o obj-$(CONFIG_POWER_RESET_LTC2952) += ltc2952-poweroff.o +obj-$(CONFIG_POWER_RESET_ODROID) += odroid-reboot.o obj-$(CONFIG_POWER_RESET_QNAP) += qnap-poweroff.o obj-$(CONFIG_POWER_RESET_RESTART) += restart-poweroff.o obj-$(CONFIG_POWER_RESET_SUN6I) += sun6i-reboot.o diff --git a/drivers/power/reset/odroid-reboot.c b/drivers/power/reset/odroid-reboot.c new file mode 100644 index 000000000000..823e93539220 --- /dev/null +++ b/drivers/power/reset/odroid-reboot.c @@ -0,0 +1,119 @@ +/* + * Copyright (c) 2014 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/io.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of_platform.h> +#include <linux/of_gpio.h> +#include <linux/reboot.h> +#include <linux/regmap.h> + +#include <asm/system_misc.h> + +#define PS_HOLD_CONTROL 0x330C + +struct odroid_reboot_data { + struct device *dev; + int power_gpio; + struct regmap *reg_pmu; + void (*reboot_func)(enum reboot_mode mode, const char *cmd); +}; + +static struct odroid_reboot_data *reboot_data; + +static void odroid_reboot(enum reboot_mode mode, const char *cmd) +{ + local_irq_disable(); + + gpio_set_value(reboot_data->power_gpio, 0); + mdelay(150); + gpio_set_value(reboot_data->power_gpio, 1); + + reboot_data->reboot_func(mode, cmd); + + pr_emerg("%s: waiting for reboot\n", __func__); + while (1) + ; +} + +static void odroid_power_off(void) +{ + regmap_update_bits(reboot_data->reg_pmu, PS_HOLD_CONTROL, 0xffffffff, 0x5200); + while (1) { + pr_emerg("%s: should not reach here!\n", __func__); + msleep(1000); + } +} + +static struct odroid_reboot_data *odroid_reboot_parse_dt(struct device *dev) +{ + struct device_node *np = dev->of_node; + struct odroid_reboot_data *data; + + data = devm_kzalloc(dev, sizeof(struct odroid_reboot_data), GFP_KERNEL); + if (!data) + return NULL; + + data->power_gpio = of_get_named_gpio(np, "reset-gpios", 0); + if (!gpio_is_valid(data->power_gpio)) { + dev_err(dev, "invalid reset gpio pin\n"); + return NULL; + } + devm_gpio_request(dev, data->power_gpio, "reset"); + + data->reg_pmu = syscon_regmap_lookup_by_phandle(np, + "samsung,pmureg-phandle"); + if (IS_ERR(data->reg_pmu)) { + dev_err(dev, "failed to map PMU registers\n"); + return NULL; + } + + return data; +} + +static int odroid_reboot_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + + if (pdev->dev.of_node) + reboot_data = odroid_reboot_parse_dt(dev); + + if (!reboot_data) + return -EINVAL; + + reboot_data->dev = &pdev->dev; + reboot_data->reboot_func = arm_pm_restart; + + /* grab reboot arm specific hook */ + arm_pm_restart = odroid_reboot; + + /* register power off function */ + pm_power_off = odroid_power_off; + + return 0; +} + +static struct of_device_id odroid_reboot_of_match[] = { + { .compatible = "hardkernel,odroid-reboot", }, + { }, +}; + +static struct platform_driver odroid_reboot_driver = { + .probe = odroid_reboot_probe, + .driver = { + .name = "odroid-reboot", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(odroid_reboot_of_match), + } +}; +module_platform_driver(odroid_reboot_driver);
This patch adds a driver implementing correct reboot and poweroff procedures for Exynos4412-based Hardkernel's Odroid X/X2/U2/U3/U3+ boards. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> --- .../bindings/power/reset/odroid-reset.txt | 18 ++++ drivers/power/reset/Kconfig | 6 ++ drivers/power/reset/Makefile | 1 + drivers/power/reset/odroid-reboot.c | 119 +++++++++++++++++++++ 4 files changed, 144 insertions(+) create mode 100644 Documentation/devicetree/bindings/power/reset/odroid-reset.txt create mode 100644 drivers/power/reset/odroid-reboot.c