diff mbox

[2/7] ARM: dts: qcom: Add PM8941 functions device nodes

Message ID 1427900715-26273-3-git-send-email-ivan.ivanov@linaro.org (mailing list archive)
State Superseded, archived
Headers show

Commit Message

Ivan T. Ivanov April 1, 2015, 3:05 p.m. UTC
Add configuration nodes for following devices:

* GPIO block, with 36 pins
* MPP block, with 8 pins
* Current ADC (IADC)
* Volatage ADC (VADC), with multiple inputs
* Thermal sensor device, which is using on chip VADC
  channel report PMIC die temperature
* Power key device, which is responsible for clean system
  reboot or shutdown
* White LED device
* RTC device

Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
---
 arch/arm/boot/dts/qcom-pm8941.dtsi | 98 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 98 insertions(+)

--
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Comments

Kumar Gala April 1, 2015, 7:58 p.m. UTC | #1
On Apr 1, 2015, at 10:05 AM, Ivan T. Ivanov <ivan.ivanov@linaro.org> wrote:

> Add configuration nodes for following devices:
> 
> * GPIO block, with 36 pins
> * MPP block, with 8 pins
> * Current ADC (IADC)
> * Volatage ADC (VADC), with multiple inputs
> * Thermal sensor device, which is using on chip VADC
>  channel report PMIC die temperature
> * Power key device, which is responsible for clean system
>  reboot or shutdown
> * White LED device
> * RTC device
> 
> Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
> ---
> arch/arm/boot/dts/qcom-pm8941.dtsi | 98 ++++++++++++++++++++++++++++++++++++++
> 1 file changed, 98 insertions(+)

please cleanup level/edge cell values to use defines

- k
diff mbox

Patch

diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
index 24c5088..23a9268 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -1,3 +1,5 @@ 
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>

 &spmi_bus {
@@ -7,6 +9,89 @@ 
 		reg = <0x0 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000 0x100>,
+			      <0x6100 0x100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		pwrkey@800 {
+			compatible = "qcom,pm8941-pwrkey";
+			reg = <0x800 0x100>;
+			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+			debounce = <15625>;
+			bias-pull-up;
+		};
+
+		pm8941_gpios: gpios@c000 {
+			compatible = "qcom,pm8941-gpio";
+			reg = <0xc000 0x2400>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <0 0xc0 0 0>, <0 0xc1 0 0>, <0 0xc2 0 0>, <0 0xc3 0 0>,
+				     <0 0xc4 0 0>, <0 0xc5 0 0>, <0 0xc6 0 0>, <0 0xc7 0 0>,
+				     <0 0xc8 0 0>, <0 0xc9 0 0>, <0 0xca 0 0>, <0 0xcb 0 0>,
+				     <0 0xcc 0 0>, <0 0xcd 0 0>, <0 0xce 0 0>, <0 0xcf 0 0>,
+				     <0 0xd0 0 0>, <0 0xd1 0 0>, <0 0xd2 0 0>, <0 0xd3 0 0>,
+				     <0 0xd4 0 0>, <0 0xd5 0 0>, <0 0xd6 0 0>, <0 0xd7 0 0>,
+				     <0 0xd8 0 0>, <0 0xd9 0 0>, <0 0xda 0 0>, <0 0xdb 0 0>,
+				     <0 0xdc 0 0>, <0 0xdd 0 0>, <0 0xde 0 0>, <0 0xdf 0 0>,
+				     <0 0xe0 0 0>, <0 0xe1 0 0>, <0 0xe2 0 0>, <0 0xe3 0 0>;
+		};
+
+		pm8941_mpps: mpps@a000 {
+			compatible = "qcom,pm8941-mpp";
+			reg = <0xa000 0x800>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <0 0xa0 0 0>, <0 0xa1 0 0>, <0 0xa2 0 0>, <0 0xa3 0 0>,
+				     <0 0xa4 0 0>, <0 0xa5 0 0>, <0 0xa6 0 0>, <0 0xa7 0 0>;
+		};
+
+		pm8941_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400 0x100>;
+			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8941_vadc: vadc@3100 {
+			compatible = "qcom,spmi-vadc";
+			reg = <0x3100 0x100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			die_temp {
+				reg = <VADC_DIE_TEMP>;
+			};
+			ref_625mv {
+				reg = <VADC_REF_625MV>;
+			};
+			ref_1250v {
+				reg = <VADC_REF_1250MV>;
+			};
+			ref_gnd {
+				reg = <VADC_GND_REF>;
+			};
+			ref_vdd {
+				reg = <VADC_VDD_VADC>;
+			};
+		};
+
+		pm8941_iadc: iadc@3600 {
+			compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
+			reg = <0x3600 0x100>,
+				  <0x12f1 0x1>;
+			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
+			qcom,external-resistor-micro-ohms = <10000>;
+		};
 	};

 	usid1: pm8941@1 {
@@ -14,5 +99,18 @@ 
 		reg = <0x1 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		wled@d800 {
+			compatible = "qcom,pm8941-wled";
+			reg = <0xd800 0x100>;
+			label = "backlight";
+
+			qcom,cs-out;
+			qcom,current-limit = <20>;
+			qcom,current-boost-limit = <805>;
+			qcom,switching-freq = <1600>;
+			qcom,ovp = <29>;
+			qcom,num-strings = <2>;
+		};
 	};
 };