| Message ID | 1428559958-1902-1-git-send-email-architt@codeaurora.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Thu, 09 Apr 2015, Archit Taneja <architt@codeaurora.org> wrote: > Allow drm_bridge objects to link to each other in order to form an encoder > chain. The requirement for creating a chain of bridges comes because the > MSM drm driver uses up its encoder and bridge objects for blocks within > the SoC itself. There isn't anything left to use if the SoC display output > is connected to an external encoder IC. Having an additional bridge > connected to the existing bridge helps here. In general, it is possible for > platforms to have multiple devices between the encoder and the > connector/panel that require some sort of configuration. > > We create drm bridge helper functions corresponding to each op in > 'drm_bridge_funcs'. These helpers call the corresponding 'drm_bridge_funcs' > op for the entire chain of bridges. These helpers are used internally by > drm_atomic_helper.c and drm_crtc_helper.c. > > The drm_bridge_enable/pre_enable helpers execute enable/pre_enable ops of the > bridge closet to the encoder, and proceed until the last bridge in the chain > is enabled. The same holds for drm_bridge_mode_set/mode_fixup helpers. The > drm_bridge_disable/post_disable helpers disable the last bridge in the chain > first, and proceed until the first bridge in the chain is disabled. > > drm_bridge_attach() remains the same. As before, the driver calling this > function should make sure it has set the links correctly. The order in which > the bridges are connected to each other determines the order in which the > calls are made. One requirement is that every bridge in the chain should point > the parent encoder object. This is required since bridge drivers expect a > valid encoder pointer in drm_bridge. For example, consider a chain where an > encoder's output is connected to bridge1, and bridge1's output is connected to > bridge2: > > /* Like before, attach bridge to an encoder */ > bridge1->encoder = encoder; > ret = drm_bridge_attach(dev, bridge1); > .. > > /* > * set the first bridge's 'next' bridge to bridge2, set its encoder > * as bridge1's encoder > */ > bridge1->next = bridge2 > bridge2->encoder = bridge1->encoder; > ret = drm_bridge_attach(dev, bridge2); > > ... > ... > > This method of bridge chaining isn't intrusive and existing drivers that use > drm_bridge will behave the same way as before. The bridge helpers also cleans > up the atomic and crtc helper files a bit. > > Signed-off-by: Archit Taneja <architt@codeaurora.org> > --- > drivers/gpu/drm/drm_atomic_helper.c | 29 ++++++---------- > drivers/gpu/drm/drm_bridge.c | 68 +++++++++++++++++++++++++++++++++++++ > drivers/gpu/drm/drm_crtc_helper.c | 54 +++++++++++------------------ > include/drm/drm_crtc.h | 14 ++++++++ > 4 files changed, 112 insertions(+), 53 deletions(-) > > diff --git a/drivers/gpu/drm/drm_atomic_helper.c b/drivers/gpu/drm/drm_atomic_helper.c > index 7e3a52b..0b4574e 100644 > --- a/drivers/gpu/drm/drm_atomic_helper.c > +++ b/drivers/gpu/drm/drm_atomic_helper.c > @@ -287,14 +287,11 @@ mode_fixup(struct drm_atomic_state *state) > encoder = conn_state->best_encoder; > funcs = encoder->helper_private; > > - if (encoder->bridge && encoder->bridge->funcs->mode_fixup) { > - ret = encoder->bridge->funcs->mode_fixup( > - encoder->bridge, &crtc_state->mode, > - &crtc_state->adjusted_mode); > - if (!ret) { > - DRM_DEBUG_KMS("Bridge fixup failed\n"); > - return -EINVAL; > - } > + ret = drm_bridge_mode_fixup(encoder->bridge, &crtc_state->mode, > + &crtc_state->adjusted_mode); > + if (!ret) { > + DRM_DEBUG_KMS("Bridge fixup failed\n"); > + return -EINVAL; > } > > if (funcs->atomic_check) { > @@ -607,8 +604,7 @@ disable_outputs(struct drm_device *dev, struct drm_atomic_state *old_state) > * Each encoder has at most one connector (since we always steal > * it away), so we won't call call disable hooks twice. > */ > - if (encoder->bridge) > - encoder->bridge->funcs->disable(encoder->bridge); > + drm_bridge_disable(encoder->bridge); > > /* Right function depends upon target state. */ > if (connector->state->crtc && funcs->prepare) > @@ -618,8 +614,7 @@ disable_outputs(struct drm_device *dev, struct drm_atomic_state *old_state) > else > funcs->dpms(encoder, DRM_MODE_DPMS_OFF); > > - if (encoder->bridge) > - encoder->bridge->funcs->post_disable(encoder->bridge); > + drm_bridge_post_disable(encoder->bridge); > } > > for (i = 0; i < ncrtcs; i++) { > @@ -761,9 +756,7 @@ crtc_set_mode(struct drm_device *dev, struct drm_atomic_state *old_state) > */ > funcs->mode_set(encoder, mode, adjusted_mode); > > - if (encoder->bridge && encoder->bridge->funcs->mode_set) > - encoder->bridge->funcs->mode_set(encoder->bridge, > - mode, adjusted_mode); > + drm_bridge_mode_set(encoder->bridge, mode, adjusted_mode); > } > } > > @@ -849,16 +842,14 @@ void drm_atomic_helper_commit_post_planes(struct drm_device *dev, > * Each encoder has at most one connector (since we always steal > * it away), so we won't call call enable hooks twice. > */ > - if (encoder->bridge) > - encoder->bridge->funcs->pre_enable(encoder->bridge); > + drm_bridge_pre_enable(encoder->bridge); > > if (funcs->enable) > funcs->enable(encoder); > else > funcs->commit(encoder); > > - if (encoder->bridge) > - encoder->bridge->funcs->enable(encoder->bridge); > + drm_bridge_enable(encoder->bridge); > } > } > EXPORT_SYMBOL(drm_atomic_helper_commit_post_planes); > diff --git a/drivers/gpu/drm/drm_bridge.c b/drivers/gpu/drm/drm_bridge.c > index d1187e5..b52c387 100644 > --- a/drivers/gpu/drm/drm_bridge.c > +++ b/drivers/gpu/drm/drm_bridge.c > @@ -66,6 +66,74 @@ extern int drm_bridge_attach(struct drm_device *dev, struct drm_bridge *bridge) > } > EXPORT_SYMBOL(drm_bridge_attach); > > +bool drm_bridge_mode_fixup(struct drm_bridge *bridge, > + const struct drm_display_mode *mode, > + struct drm_display_mode *adjusted_mode) > +{ > + bool ret = true; > + > + if (!bridge) > + return true; > + > + if (bridge->funcs->mode_fixup) > + ret = bridge->funcs->mode_fixup(bridge, mode, adjusted_mode); > + > + return ret & drm_bridge_mode_fixup(bridge->next, mode, adjusted_mode); Is that an intentional bitwise rather than logical AND? If it is, please don't combine this into the return statement. How about EXPORT_SYMBOLs for the new functions? Other than these, the patch LGTM. BR, Jani. > +} > + > +void drm_bridge_disable(struct drm_bridge *bridge) > +{ > + if (!bridge) > + return; > + > + drm_bridge_disable(bridge->next); > + > + bridge->funcs->disable(bridge); > +} > + > +void drm_bridge_post_disable(struct drm_bridge *bridge) > +{ > + if (!bridge) > + return; > + > + drm_bridge_post_disable(bridge->next); > + > + bridge->funcs->post_disable(bridge); > +} > + > +void drm_bridge_mode_set(struct drm_bridge *bridge, > + struct drm_display_mode *mode, > + struct drm_display_mode *adjusted_mode) > +{ > + if (!bridge) > + return; > + > + if (bridge->funcs->mode_set) > + bridge->funcs->mode_set(bridge, mode, adjusted_mode); > + > + drm_bridge_mode_set(bridge->next, mode, adjusted_mode); > +} > + > +void drm_bridge_pre_enable(struct drm_bridge *bridge) > +{ > + if (!bridge) > + return; > + > + bridge->funcs->pre_enable(bridge); > + > + drm_bridge_pre_enable(bridge->next); > +} > + > +void drm_bridge_enable(struct drm_bridge *bridge) > +{ > + if (!bridge) > + return; > + > + bridge->funcs->enable(bridge); > + > + drm_bridge_enable(bridge->next); > +} > + > #ifdef CONFIG_OF > struct drm_bridge *of_drm_find_bridge(struct device_node *np) > { > diff --git a/drivers/gpu/drm/drm_crtc_helper.c b/drivers/gpu/drm/drm_crtc_helper.c > index b1979e7..a199f49 100644 > --- a/drivers/gpu/drm/drm_crtc_helper.c > +++ b/drivers/gpu/drm/drm_crtc_helper.c > @@ -163,16 +163,14 @@ drm_encoder_disable(struct drm_encoder *encoder) > { > struct drm_encoder_helper_funcs *encoder_funcs = encoder->helper_private; > > - if (encoder->bridge) > - encoder->bridge->funcs->disable(encoder->bridge); > + drm_bridge_disable(encoder->bridge); > > if (encoder_funcs->disable) > (*encoder_funcs->disable)(encoder); > else > (*encoder_funcs->dpms)(encoder, DRM_MODE_DPMS_OFF); > > - if (encoder->bridge) > - encoder->bridge->funcs->post_disable(encoder->bridge); > + drm_bridge_post_disable(encoder->bridge); > } > > static void __drm_helper_disable_unused_functions(struct drm_device *dev) > @@ -311,13 +309,11 @@ bool drm_crtc_helper_set_mode(struct drm_crtc *crtc, > if (encoder->crtc != crtc) > continue; > > - if (encoder->bridge && encoder->bridge->funcs->mode_fixup) { > - ret = encoder->bridge->funcs->mode_fixup( > - encoder->bridge, mode, adjusted_mode); > - if (!ret) { > - DRM_DEBUG_KMS("Bridge fixup failed\n"); > - goto done; > - } > + ret = drm_bridge_mode_fixup(encoder->bridge, > + mode, adjusted_mode); > + if (!ret) { > + DRM_DEBUG_KMS("Bridge fixup failed\n"); > + goto done; > } > > encoder_funcs = encoder->helper_private; > @@ -340,15 +336,13 @@ bool drm_crtc_helper_set_mode(struct drm_crtc *crtc, > if (encoder->crtc != crtc) > continue; > > - if (encoder->bridge) > - encoder->bridge->funcs->disable(encoder->bridge); > + drm_bridge_disable(encoder->bridge); > > encoder_funcs = encoder->helper_private; > /* Disable the encoders as the first thing we do. */ > encoder_funcs->prepare(encoder); > > - if (encoder->bridge) > - encoder->bridge->funcs->post_disable(encoder->bridge); > + drm_bridge_post_disable(encoder->bridge); > } > > drm_crtc_prepare_encoders(dev); > @@ -373,9 +367,7 @@ bool drm_crtc_helper_set_mode(struct drm_crtc *crtc, > encoder_funcs = encoder->helper_private; > encoder_funcs->mode_set(encoder, mode, adjusted_mode); > > - if (encoder->bridge && encoder->bridge->funcs->mode_set) > - encoder->bridge->funcs->mode_set(encoder->bridge, mode, > - adjusted_mode); > + drm_bridge_mode_set(encoder->bridge, mode, adjusted_mode); > } > > /* Now enable the clocks, plane, pipe, and connectors that we set up. */ > @@ -386,14 +378,12 @@ bool drm_crtc_helper_set_mode(struct drm_crtc *crtc, > if (encoder->crtc != crtc) > continue; > > - if (encoder->bridge) > - encoder->bridge->funcs->pre_enable(encoder->bridge); > + drm_bridge_pre_enable(encoder->bridge); > > encoder_funcs = encoder->helper_private; > encoder_funcs->commit(encoder); > > - if (encoder->bridge) > - encoder->bridge->funcs->enable(encoder->bridge); > + drm_bridge_enable(encoder->bridge); > } > > /* Store real post-adjustment hardware mode. */ > @@ -734,23 +724,19 @@ static void drm_helper_encoder_dpms(struct drm_encoder *encoder, int mode) > struct drm_bridge *bridge = encoder->bridge; > struct drm_encoder_helper_funcs *encoder_funcs; > > - if (bridge) { > - if (mode == DRM_MODE_DPMS_ON) > - bridge->funcs->pre_enable(bridge); > - else > - bridge->funcs->disable(bridge); > - } > + if (mode == DRM_MODE_DPMS_ON) > + drm_bridge_pre_enable(bridge); > + else > + drm_bridge_disable(bridge); > > encoder_funcs = encoder->helper_private; > if (encoder_funcs->dpms) > encoder_funcs->dpms(encoder, mode); > > - if (bridge) { > - if (mode == DRM_MODE_DPMS_ON) > - bridge->funcs->enable(bridge); > - else > - bridge->funcs->post_disable(bridge); > - } > + if (mode == DRM_MODE_DPMS_ON) > + drm_bridge_enable(bridge); > + else > + drm_bridge_post_disable(bridge); > } > > static int drm_helper_choose_crtc_dpms(struct drm_crtc *crtc) > diff --git a/include/drm/drm_crtc.h b/include/drm/drm_crtc.h > index 920e21a..8fced1d 100644 > --- a/include/drm/drm_crtc.h > +++ b/include/drm/drm_crtc.h > @@ -893,6 +893,8 @@ struct drm_bridge_funcs { > /** > * struct drm_bridge - central DRM bridge control structure > * @dev: DRM device this bridge belongs to > + * @encoder: encoder to which this bridge is connected > + * @next: the next bridge in the encoder chain > * @of_node: device node pointer to the bridge > * @list: to keep track of all added bridges > * @base: base mode object > @@ -902,6 +904,7 @@ struct drm_bridge_funcs { > struct drm_bridge { > struct drm_device *dev; > struct drm_encoder *encoder; > + struct drm_bridge *next; > #ifdef CONFIG_OF > struct device_node *of_node; > #endif > @@ -1225,6 +1228,17 @@ extern void drm_bridge_remove(struct drm_bridge *bridge); > extern struct drm_bridge *of_drm_find_bridge(struct device_node *np); > extern int drm_bridge_attach(struct drm_device *dev, struct drm_bridge *bridge); > > +bool drm_bridge_mode_fixup(struct drm_bridge *bridge, > + const struct drm_display_mode *mode, > + struct drm_display_mode *adjusted_mode); > +void drm_bridge_disable(struct drm_bridge *bridge); > +void drm_bridge_post_disable(struct drm_bridge *bridge); > +void drm_bridge_mode_set(struct drm_bridge *bridge, > + struct drm_display_mode *mode, > + struct drm_display_mode *adjusted_mode); > +void drm_bridge_pre_enable(struct drm_bridge *bridge); > +void drm_bridge_enable(struct drm_bridge *bridge); > + > extern int drm_encoder_init(struct drm_device *dev, > struct drm_encoder *encoder, > const struct drm_encoder_funcs *funcs, > -- > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, > hosted by The Linux Foundation > > _______________________________________________ > dri-devel mailing list > dri-devel@lists.freedesktop.org > http://lists.freedesktop.org/mailman/listinfo/dri-devel
Hi, On 04/09/2015 12:54 PM, Jani Nikula wrote: > On Thu, 09 Apr 2015, Archit Taneja <architt@codeaurora.org> wrote: >> Allow drm_bridge objects to link to each other in order to form an encoder >> chain. The requirement for creating a chain of bridges comes because the >> MSM drm driver uses up its encoder and bridge objects for blocks within >> the SoC itself. There isn't anything left to use if the SoC display output >> is connected to an external encoder IC. Having an additional bridge >> connected to the existing bridge helps here. In general, it is possible for >> platforms to have multiple devices between the encoder and the >> connector/panel that require some sort of configuration. >> >> We create drm bridge helper functions corresponding to each op in >> 'drm_bridge_funcs'. These helpers call the corresponding 'drm_bridge_funcs' >> op for the entire chain of bridges. These helpers are used internally by >> drm_atomic_helper.c and drm_crtc_helper.c. >> >> The drm_bridge_enable/pre_enable helpers execute enable/pre_enable ops of the >> bridge closet to the encoder, and proceed until the last bridge in the chain >> is enabled. The same holds for drm_bridge_mode_set/mode_fixup helpers. The >> drm_bridge_disable/post_disable helpers disable the last bridge in the chain >> first, and proceed until the first bridge in the chain is disabled. >> >> drm_bridge_attach() remains the same. As before, the driver calling this >> function should make sure it has set the links correctly. The order in which >> the bridges are connected to each other determines the order in which the >> calls are made. One requirement is that every bridge in the chain should point >> the parent encoder object. This is required since bridge drivers expect a >> valid encoder pointer in drm_bridge. For example, consider a chain where an >> encoder's output is connected to bridge1, and bridge1's output is connected to >> bridge2: >> >> /* Like before, attach bridge to an encoder */ >> bridge1->encoder = encoder; >> ret = drm_bridge_attach(dev, bridge1); >> .. >> >> /* >> * set the first bridge's 'next' bridge to bridge2, set its encoder >> * as bridge1's encoder >> */ >> bridge1->next = bridge2 >> bridge2->encoder = bridge1->encoder; >> ret = drm_bridge_attach(dev, bridge2); >> >> ... >> ... >> >> This method of bridge chaining isn't intrusive and existing drivers that use >> drm_bridge will behave the same way as before. The bridge helpers also cleans >> up the atomic and crtc helper files a bit. >> >> Signed-off-by: Archit Taneja <architt@codeaurora.org> >> --- >> drivers/gpu/drm/drm_atomic_helper.c | 29 ++++++---------- >> drivers/gpu/drm/drm_bridge.c | 68 +++++++++++++++++++++++++++++++++++++ >> drivers/gpu/drm/drm_crtc_helper.c | 54 +++++++++++------------------ >> include/drm/drm_crtc.h | 14 ++++++++ >> 4 files changed, 112 insertions(+), 53 deletions(-) >> >> diff --git a/drivers/gpu/drm/drm_atomic_helper.c b/drivers/gpu/drm/drm_atomic_helper.c >> index 7e3a52b..0b4574e 100644 >> --- a/drivers/gpu/drm/drm_atomic_helper.c >> +++ b/drivers/gpu/drm/drm_atomic_helper.c >> @@ -287,14 +287,11 @@ mode_fixup(struct drm_atomic_state *state) >> encoder = conn_state->best_encoder; >> funcs = encoder->helper_private; >> >> - if (encoder->bridge && encoder->bridge->funcs->mode_fixup) { >> - ret = encoder->bridge->funcs->mode_fixup( >> - encoder->bridge, &crtc_state->mode, >> - &crtc_state->adjusted_mode); >> - if (!ret) { >> - DRM_DEBUG_KMS("Bridge fixup failed\n"); >> - return -EINVAL; >> - } >> + ret = drm_bridge_mode_fixup(encoder->bridge, &crtc_state->mode, >> + &crtc_state->adjusted_mode); >> + if (!ret) { >> + DRM_DEBUG_KMS("Bridge fixup failed\n"); >> + return -EINVAL; >> } >> >> if (funcs->atomic_check) { >> @@ -607,8 +604,7 @@ disable_outputs(struct drm_device *dev, struct drm_atomic_state *old_state) >> * Each encoder has at most one connector (since we always steal >> * it away), so we won't call call disable hooks twice. >> */ >> - if (encoder->bridge) >> - encoder->bridge->funcs->disable(encoder->bridge); >> + drm_bridge_disable(encoder->bridge); >> >> /* Right function depends upon target state. */ >> if (connector->state->crtc && funcs->prepare) >> @@ -618,8 +614,7 @@ disable_outputs(struct drm_device *dev, struct drm_atomic_state *old_state) >> else >> funcs->dpms(encoder, DRM_MODE_DPMS_OFF); >> >> - if (encoder->bridge) >> - encoder->bridge->funcs->post_disable(encoder->bridge); >> + drm_bridge_post_disable(encoder->bridge); >> } >> >> for (i = 0; i < ncrtcs; i++) { >> @@ -761,9 +756,7 @@ crtc_set_mode(struct drm_device *dev, struct drm_atomic_state *old_state) >> */ >> funcs->mode_set(encoder, mode, adjusted_mode); >> >> - if (encoder->bridge && encoder->bridge->funcs->mode_set) >> - encoder->bridge->funcs->mode_set(encoder->bridge, >> - mode, adjusted_mode); >> + drm_bridge_mode_set(encoder->bridge, mode, adjusted_mode); >> } >> } >> >> @@ -849,16 +842,14 @@ void drm_atomic_helper_commit_post_planes(struct drm_device *dev, >> * Each encoder has at most one connector (since we always steal >> * it away), so we won't call call enable hooks twice. >> */ >> - if (encoder->bridge) >> - encoder->bridge->funcs->pre_enable(encoder->bridge); >> + drm_bridge_pre_enable(encoder->bridge); >> >> if (funcs->enable) >> funcs->enable(encoder); >> else >> funcs->commit(encoder); >> >> - if (encoder->bridge) >> - encoder->bridge->funcs->enable(encoder->bridge); >> + drm_bridge_enable(encoder->bridge); >> } >> } >> EXPORT_SYMBOL(drm_atomic_helper_commit_post_planes); >> diff --git a/drivers/gpu/drm/drm_bridge.c b/drivers/gpu/drm/drm_bridge.c >> index d1187e5..b52c387 100644 >> --- a/drivers/gpu/drm/drm_bridge.c >> +++ b/drivers/gpu/drm/drm_bridge.c >> @@ -66,6 +66,74 @@ extern int drm_bridge_attach(struct drm_device *dev, struct drm_bridge *bridge) >> } >> EXPORT_SYMBOL(drm_bridge_attach); >> >> +bool drm_bridge_mode_fixup(struct drm_bridge *bridge, >> + const struct drm_display_mode *mode, >> + struct drm_display_mode *adjusted_mode) >> +{ >> + bool ret = true; >> + >> + if (!bridge) >> + return true; >> + >> + if (bridge->funcs->mode_fixup) >> + ret = bridge->funcs->mode_fixup(bridge, mode, adjusted_mode); >> + >> + return ret & drm_bridge_mode_fixup(bridge->next, mode, adjusted_mode); > > Is that an intentional bitwise rather than logical AND? If it is, please > don't combine this into the return statement. This looks like a mistake from my end. I'll fix this. > > How about EXPORT_SYMBOLs for the new functions? I'll add this. > > Other than these, the patch LGTM. Thanks for the review! Archit
diff --git a/drivers/gpu/drm/drm_atomic_helper.c b/drivers/gpu/drm/drm_atomic_helper.c index 7e3a52b..0b4574e 100644 --- a/drivers/gpu/drm/drm_atomic_helper.c +++ b/drivers/gpu/drm/drm_atomic_helper.c @@ -287,14 +287,11 @@ mode_fixup(struct drm_atomic_state *state) encoder = conn_state->best_encoder; funcs = encoder->helper_private; - if (encoder->bridge && encoder->bridge->funcs->mode_fixup) { - ret = encoder->bridge->funcs->mode_fixup( - encoder->bridge, &crtc_state->mode, - &crtc_state->adjusted_mode); - if (!ret) { - DRM_DEBUG_KMS("Bridge fixup failed\n"); - return -EINVAL; - } + ret = drm_bridge_mode_fixup(encoder->bridge, &crtc_state->mode, + &crtc_state->adjusted_mode); + if (!ret) { + DRM_DEBUG_KMS("Bridge fixup failed\n"); + return -EINVAL; } if (funcs->atomic_check) { @@ -607,8 +604,7 @@ disable_outputs(struct drm_device *dev, struct drm_atomic_state *old_state) * Each encoder has at most one connector (since we always steal * it away), so we won't call call disable hooks twice. */ - if (encoder->bridge) - encoder->bridge->funcs->disable(encoder->bridge); + drm_bridge_disable(encoder->bridge); /* Right function depends upon target state. */ if (connector->state->crtc && funcs->prepare) @@ -618,8 +614,7 @@ disable_outputs(struct drm_device *dev, struct drm_atomic_state *old_state) else funcs->dpms(encoder, DRM_MODE_DPMS_OFF); - if (encoder->bridge) - encoder->bridge->funcs->post_disable(encoder->bridge); + drm_bridge_post_disable(encoder->bridge); } for (i = 0; i < ncrtcs; i++) { @@ -761,9 +756,7 @@ crtc_set_mode(struct drm_device *dev, struct drm_atomic_state *old_state) */ funcs->mode_set(encoder, mode, adjusted_mode); - if (encoder->bridge && encoder->bridge->funcs->mode_set) - encoder->bridge->funcs->mode_set(encoder->bridge, - mode, adjusted_mode); + drm_bridge_mode_set(encoder->bridge, mode, adjusted_mode); } } @@ -849,16 +842,14 @@ void drm_atomic_helper_commit_post_planes(struct drm_device *dev, * Each encoder has at most one connector (since we always steal * it away), so we won't call call enable hooks twice. */ - if (encoder->bridge) - encoder->bridge->funcs->pre_enable(encoder->bridge); + drm_bridge_pre_enable(encoder->bridge); if (funcs->enable) funcs->enable(encoder); else funcs->commit(encoder); - if (encoder->bridge) - encoder->bridge->funcs->enable(encoder->bridge); + drm_bridge_enable(encoder->bridge); } } EXPORT_SYMBOL(drm_atomic_helper_commit_post_planes); diff --git a/drivers/gpu/drm/drm_bridge.c b/drivers/gpu/drm/drm_bridge.c index d1187e5..b52c387 100644 --- a/drivers/gpu/drm/drm_bridge.c +++ b/drivers/gpu/drm/drm_bridge.c @@ -66,6 +66,74 @@ extern int drm_bridge_attach(struct drm_device *dev, struct drm_bridge *bridge) } EXPORT_SYMBOL(drm_bridge_attach); +bool drm_bridge_mode_fixup(struct drm_bridge *bridge, + const struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) +{ + bool ret = true; + + if (!bridge) + return true; + + if (bridge->funcs->mode_fixup) + ret = bridge->funcs->mode_fixup(bridge, mode, adjusted_mode); + + return ret & drm_bridge_mode_fixup(bridge->next, mode, adjusted_mode); +} + +void drm_bridge_disable(struct drm_bridge *bridge) +{ + if (!bridge) + return; + + drm_bridge_disable(bridge->next); + + bridge->funcs->disable(bridge); +} + +void drm_bridge_post_disable(struct drm_bridge *bridge) +{ + if (!bridge) + return; + + drm_bridge_post_disable(bridge->next); + + bridge->funcs->post_disable(bridge); +} + +void drm_bridge_mode_set(struct drm_bridge *bridge, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode) +{ + if (!bridge) + return; + + if (bridge->funcs->mode_set) + bridge->funcs->mode_set(bridge, mode, adjusted_mode); + + drm_bridge_mode_set(bridge->next, mode, adjusted_mode); +} + +void drm_bridge_pre_enable(struct drm_bridge *bridge) +{ + if (!bridge) + return; + + bridge->funcs->pre_enable(bridge); + + drm_bridge_pre_enable(bridge->next); +} + +void drm_bridge_enable(struct drm_bridge *bridge) +{ + if (!bridge) + return; + + bridge->funcs->enable(bridge); + + drm_bridge_enable(bridge->next); +} + #ifdef CONFIG_OF struct drm_bridge *of_drm_find_bridge(struct device_node *np) { diff --git a/drivers/gpu/drm/drm_crtc_helper.c b/drivers/gpu/drm/drm_crtc_helper.c index b1979e7..a199f49 100644 --- a/drivers/gpu/drm/drm_crtc_helper.c +++ b/drivers/gpu/drm/drm_crtc_helper.c @@ -163,16 +163,14 @@ drm_encoder_disable(struct drm_encoder *encoder) { struct drm_encoder_helper_funcs *encoder_funcs = encoder->helper_private; - if (encoder->bridge) - encoder->bridge->funcs->disable(encoder->bridge); + drm_bridge_disable(encoder->bridge); if (encoder_funcs->disable) (*encoder_funcs->disable)(encoder); else (*encoder_funcs->dpms)(encoder, DRM_MODE_DPMS_OFF); - if (encoder->bridge) - encoder->bridge->funcs->post_disable(encoder->bridge); + drm_bridge_post_disable(encoder->bridge); } static void __drm_helper_disable_unused_functions(struct drm_device *dev) @@ -311,13 +309,11 @@ bool drm_crtc_helper_set_mode(struct drm_crtc *crtc, if (encoder->crtc != crtc) continue; - if (encoder->bridge && encoder->bridge->funcs->mode_fixup) { - ret = encoder->bridge->funcs->mode_fixup( - encoder->bridge, mode, adjusted_mode); - if (!ret) { - DRM_DEBUG_KMS("Bridge fixup failed\n"); - goto done; - } + ret = drm_bridge_mode_fixup(encoder->bridge, + mode, adjusted_mode); + if (!ret) { + DRM_DEBUG_KMS("Bridge fixup failed\n"); + goto done; } encoder_funcs = encoder->helper_private; @@ -340,15 +336,13 @@ bool drm_crtc_helper_set_mode(struct drm_crtc *crtc, if (encoder->crtc != crtc) continue; - if (encoder->bridge) - encoder->bridge->funcs->disable(encoder->bridge); + drm_bridge_disable(encoder->bridge); encoder_funcs = encoder->helper_private; /* Disable the encoders as the first thing we do. */ encoder_funcs->prepare(encoder); - if (encoder->bridge) - encoder->bridge->funcs->post_disable(encoder->bridge); + drm_bridge_post_disable(encoder->bridge); } drm_crtc_prepare_encoders(dev); @@ -373,9 +367,7 @@ bool drm_crtc_helper_set_mode(struct drm_crtc *crtc, encoder_funcs = encoder->helper_private; encoder_funcs->mode_set(encoder, mode, adjusted_mode); - if (encoder->bridge && encoder->bridge->funcs->mode_set) - encoder->bridge->funcs->mode_set(encoder->bridge, mode, - adjusted_mode); + drm_bridge_mode_set(encoder->bridge, mode, adjusted_mode); } /* Now enable the clocks, plane, pipe, and connectors that we set up. */ @@ -386,14 +378,12 @@ bool drm_crtc_helper_set_mode(struct drm_crtc *crtc, if (encoder->crtc != crtc) continue; - if (encoder->bridge) - encoder->bridge->funcs->pre_enable(encoder->bridge); + drm_bridge_pre_enable(encoder->bridge); encoder_funcs = encoder->helper_private; encoder_funcs->commit(encoder); - if (encoder->bridge) - encoder->bridge->funcs->enable(encoder->bridge); + drm_bridge_enable(encoder->bridge); } /* Store real post-adjustment hardware mode. */ @@ -734,23 +724,19 @@ static void drm_helper_encoder_dpms(struct drm_encoder *encoder, int mode) struct drm_bridge *bridge = encoder->bridge; struct drm_encoder_helper_funcs *encoder_funcs; - if (bridge) { - if (mode == DRM_MODE_DPMS_ON) - bridge->funcs->pre_enable(bridge); - else - bridge->funcs->disable(bridge); - } + if (mode == DRM_MODE_DPMS_ON) + drm_bridge_pre_enable(bridge); + else + drm_bridge_disable(bridge); encoder_funcs = encoder->helper_private; if (encoder_funcs->dpms) encoder_funcs->dpms(encoder, mode); - if (bridge) { - if (mode == DRM_MODE_DPMS_ON) - bridge->funcs->enable(bridge); - else - bridge->funcs->post_disable(bridge); - } + if (mode == DRM_MODE_DPMS_ON) + drm_bridge_enable(bridge); + else + drm_bridge_post_disable(bridge); } static int drm_helper_choose_crtc_dpms(struct drm_crtc *crtc) diff --git a/include/drm/drm_crtc.h b/include/drm/drm_crtc.h index 920e21a..8fced1d 100644 --- a/include/drm/drm_crtc.h +++ b/include/drm/drm_crtc.h @@ -893,6 +893,8 @@ struct drm_bridge_funcs { /** * struct drm_bridge - central DRM bridge control structure * @dev: DRM device this bridge belongs to + * @encoder: encoder to which this bridge is connected + * @next: the next bridge in the encoder chain * @of_node: device node pointer to the bridge * @list: to keep track of all added bridges * @base: base mode object @@ -902,6 +904,7 @@ struct drm_bridge_funcs { struct drm_bridge { struct drm_device *dev; struct drm_encoder *encoder; + struct drm_bridge *next; #ifdef CONFIG_OF struct device_node *of_node; #endif @@ -1225,6 +1228,17 @@ extern void drm_bridge_remove(struct drm_bridge *bridge); extern struct drm_bridge *of_drm_find_bridge(struct device_node *np); extern int drm_bridge_attach(struct drm_device *dev, struct drm_bridge *bridge); +bool drm_bridge_mode_fixup(struct drm_bridge *bridge, + const struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode); +void drm_bridge_disable(struct drm_bridge *bridge); +void drm_bridge_post_disable(struct drm_bridge *bridge); +void drm_bridge_mode_set(struct drm_bridge *bridge, + struct drm_display_mode *mode, + struct drm_display_mode *adjusted_mode); +void drm_bridge_pre_enable(struct drm_bridge *bridge); +void drm_bridge_enable(struct drm_bridge *bridge); + extern int drm_encoder_init(struct drm_device *dev, struct drm_encoder *encoder, const struct drm_encoder_funcs *funcs,
Allow drm_bridge objects to link to each other in order to form an encoder chain. The requirement for creating a chain of bridges comes because the MSM drm driver uses up its encoder and bridge objects for blocks within the SoC itself. There isn't anything left to use if the SoC display output is connected to an external encoder IC. Having an additional bridge connected to the existing bridge helps here. In general, it is possible for platforms to have multiple devices between the encoder and the connector/panel that require some sort of configuration. We create drm bridge helper functions corresponding to each op in 'drm_bridge_funcs'. These helpers call the corresponding 'drm_bridge_funcs' op for the entire chain of bridges. These helpers are used internally by drm_atomic_helper.c and drm_crtc_helper.c. The drm_bridge_enable/pre_enable helpers execute enable/pre_enable ops of the bridge closet to the encoder, and proceed until the last bridge in the chain is enabled. The same holds for drm_bridge_mode_set/mode_fixup helpers. The drm_bridge_disable/post_disable helpers disable the last bridge in the chain first, and proceed until the first bridge in the chain is disabled. drm_bridge_attach() remains the same. As before, the driver calling this function should make sure it has set the links correctly. The order in which the bridges are connected to each other determines the order in which the calls are made. One requirement is that every bridge in the chain should point the parent encoder object. This is required since bridge drivers expect a valid encoder pointer in drm_bridge. For example, consider a chain where an encoder's output is connected to bridge1, and bridge1's output is connected to bridge2: /* Like before, attach bridge to an encoder */ bridge1->encoder = encoder; ret = drm_bridge_attach(dev, bridge1); .. /* * set the first bridge's 'next' bridge to bridge2, set its encoder * as bridge1's encoder */ bridge1->next = bridge2 bridge2->encoder = bridge1->encoder; ret = drm_bridge_attach(dev, bridge2); ... ... This method of bridge chaining isn't intrusive and existing drivers that use drm_bridge will behave the same way as before. The bridge helpers also cleans up the atomic and crtc helper files a bit. Signed-off-by: Archit Taneja <architt@codeaurora.org> --- drivers/gpu/drm/drm_atomic_helper.c | 29 ++++++---------- drivers/gpu/drm/drm_bridge.c | 68 +++++++++++++++++++++++++++++++++++++ drivers/gpu/drm/drm_crtc_helper.c | 54 +++++++++++------------------ include/drm/drm_crtc.h | 14 ++++++++ 4 files changed, 112 insertions(+), 53 deletions(-)