| Message ID | CAFSKS=M8bODT8bLckwtGFziknPG=32Y1=8mz3Fq0H7JcA3GhjQ@mail.gmail.com (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
[+cc Rafael] On Wed, May 6, 2015 at 9:47 AM, George McCollister <george.mccollister@gmail.com> wrote: > We're using Versalogic Tiger (VL-EPM-24) SBCs in embedded systems > running linux 3.2.x without any problems. Recently, when testing the > latest mainline kernel I found the system hard locked during boot. > > After some investigation I noticed that the kernel print time stamps > were bogus after one of the pcieports was enabled: > [ 1.658879] io scheduler cfq registered (default) > [ 1.663905] pcieport 0000:00:1c.0: enabling device (0004 -> 0007) > [ 6.254134] Serial: 8250/16550 driver, 21 ports, IRQ sharing enabled > [ 6.254134] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) > is a 16550A > [ 6.254134] 00:04: ttyS1 at I/O 0x2f8 (irq = 0, base_baud = 115200) > is a 16550A > [ 6.254134] 00:05: ttyS2 at I/O 0x3e8 (irq = 0, base_baud = 115200) > is a 16550A > [ 6.254134] 00:06: ttyS4 at I/O 0x238 (irq = 0, base_baud = 115200) > is a 16550A > > I was surprised to find that the problem existed as far back as 3.11. > I checked to make sure we were using the latest BIOS and contacted the > vendor to see if they were aware of anyone else using recent versions > of the linux kernel. They stated that they were unaware of anyone > using recent kernel versions on this board and tired to convince me to > stick with an old version. > > I then git bisected to this commit: > ac212b6980d8d5eda705864fc5a8ecddc6d6eacc ACPI / processor: Use common > hotplug infrastructure > > After diffing the kernel output before and after this commit I noticed > that the I/O BAR assigned to the pcieport (same one as above) changed > from 0x1000 to 0x2000. > > @@ -191,13 +191,13 @@ > Switching to clocksource acpi_pm > pci 0000:00:1c.0: BAR 9: assigned [mem 0x80000000-0x801fffff pref] > pci 0000:00:1c.1: BAR 9: assigned [mem 0x80200000-0x803fffff pref] > -pci 0000:00:1c.0: BAR 7: assigned [io 0x1000-0x1fff] > +pci 0000:00:1c.0: BAR 7: assigned [io 0x2000-0x2fff] > pci 0000:02:01.0: PCI bridge to [bus 03] > pci 0000:02:01.0: bridge window [mem 0xdff00000-0xdfffffff] > pci 0000:01:00.0: PCI bridge to [bus 02-03] > pci 0000:01:00.0: bridge window [mem 0xdff00000-0xdfffffff] > pci 0000:00:1c.0: PCI bridge to [bus 01-03] > -pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff] > +pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff] > pci 0000:00:1c.0: bridge window [mem 0xdff00000-0xdfffffff] > pci 0000:00:1c.0: bridge window [mem 0x80000000-0x801fffff pref] > pci 0000:00:1c.1: PCI bridge to [bus 04] > > I also noticed the kernel output 'ACPI: PM-Timer IO Port: 0x2008' and > made the connection that since acpi_pm was being used as the > clocksource and since the problems started when the BAR switched from > 0x1000 to 0x2000 an I/O conflict must be the source of the problems. > > I did some reading into ACPI (since my understanding of it was novice > at the time) and dumped the DSDT. I found no reference to anything in > the 0x2xxx I/O range though I did find the following in the FADT: > PM1a_EVT_BLK at 0x2000-0x2003 > PM1a_CNT_BLK at 0x2004-0x2005 > PM_TMR at 0x2008-0x200b > > I dumped the DSDT on other systems and found that some used PNP0C02 to > reserve I/O ranges used by the ACPI PM registers. > > I added the following to the Versalogic Tiger dsdt.dsl under the PCI > bus, compiled it and and compiled into the linux kernel: > Device (PMIO) > { > Name (_HID, EisaId ("PNP0C02") /* PNP Motherboard > Resources */) // _HID: Hardware ID > Name (_UID, 0x09) // _UID: Unique ID > Method (_CRS, 0, NotSerialized) // _CRS: Current > Resource Settings > { > Name (BUF0, ResourceTemplate () > { > IO (Decode16, > 0x2000, // Range Minimum > 0x2000, // Range Maximum > 0x01, // Alignment > 0xC, // Length > ) > IO (Decode16, > 0x20C0, // Range Minimum > 0x20C0, // Range Maximum > 0x01, // Alignment > 0x8, // Length > ) > }) > Return (BUF0) > } > } > > It booted just fine! (comment welcome on whether or not this looks > like the correct fix) > > Unfortunately even if I get the vendor to release a new BIOS with the > DSDT modifications, rolling out BIOS updates to thousands of systems > in the field will be nearly impossible. When we roll out a new kernel > to the production systems we'll need it to work with the existing > BIOS. > > I've been searching around the linux kernel for a way to apply a quirk > specific to this board. > I've found I can do something like the following and match the Poulsbo > Host bridge and that it'll fix the problem but I don't see a decent > way of restricting it to this board. > > diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c > index 85f247e..1f16dbf 100644 > --- a/drivers/pci/quirks.c > +++ b/drivers/pci/quirks.c > @@ -413,6 +413,17 @@ static void quirk_ati_exploding_mce(struct pci_dev *dev) > DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, > PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce); > > /* > + * Versa Logic Tiger > + */ > +static void quirk_versa_logic_tiger(struct pci_dev *dev) > +{ > + dev_info(&dev->dev, "Versalogic Tiger, reserving I/O ports\n"); > + request_region(0x2000, 0x0C, "Versalogic Tiger"); > + request_region(0x20C0, 0x08, "Versalogic Tiger"); > +} > +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x8100, quirk_versa_logic_tiger); > + > +/* > > Any suggestions on what could be done to get a fix for this board > mainlined into the kernel? Should I give up hope and just apply a cute > embedded non-sense hack? I think your DSDT tweak is on the right track. We have some similar things in drivers/pnp/quirks.c. Possibly a new region could be added to an existing PNP0C02 device, maybe via dmi_check_system() to limit it to this platform. But I notice that board claims Windows compatibility, so I wonder if there's a smarter way. I doubt that Windows would have a quirk for this specific board, so we should be able to make Linux work without a quirk, too. Complete dmesg logs from pre- and post-ac212b6980d8 might have a clue about what changed. It looks like your FADT should be enough to reserve those regions via acpi_reserve_resources(). But maybe there's something wrong there, or maybe we incorrectly use that for PCI space. Does your post-ac212b6980d8 /proc/ioports show those regions? Bjorn -- To unsubscribe from this list: send the line "unsubscribe linux-acpi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wed, May 6, 2015 at 10:51 AM, Bjorn Helgaas <bhelgaas@google.com> wrote: > [+cc Rafael] > > On Wed, May 6, 2015 at 9:47 AM, George McCollister > <george.mccollister@gmail.com> wrote: >> We're using Versalogic Tiger (VL-EPM-24) SBCs in embedded systems >> running linux 3.2.x without any problems. Recently, when testing the >> latest mainline kernel I found the system hard locked during boot. >> >> After some investigation I noticed that the kernel print time stamps >> were bogus after one of the pcieports was enabled: >> [ 1.658879] io scheduler cfq registered (default) >> [ 1.663905] pcieport 0000:00:1c.0: enabling device (0004 -> 0007) >> [ 6.254134] Serial: 8250/16550 driver, 21 ports, IRQ sharing enabled >> [ 6.254134] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) >> is a 16550A >> [ 6.254134] 00:04: ttyS1 at I/O 0x2f8 (irq = 0, base_baud = 115200) >> is a 16550A >> [ 6.254134] 00:05: ttyS2 at I/O 0x3e8 (irq = 0, base_baud = 115200) >> is a 16550A >> [ 6.254134] 00:06: ttyS4 at I/O 0x238 (irq = 0, base_baud = 115200) >> is a 16550A >> >> I was surprised to find that the problem existed as far back as 3.11. >> I checked to make sure we were using the latest BIOS and contacted the >> vendor to see if they were aware of anyone else using recent versions >> of the linux kernel. They stated that they were unaware of anyone >> using recent kernel versions on this board and tired to convince me to >> stick with an old version. >> >> I then git bisected to this commit: >> ac212b6980d8d5eda705864fc5a8ecddc6d6eacc ACPI / processor: Use common >> hotplug infrastructure >> >> After diffing the kernel output before and after this commit I noticed >> that the I/O BAR assigned to the pcieport (same one as above) changed >> from 0x1000 to 0x2000. >> >> @@ -191,13 +191,13 @@ >> Switching to clocksource acpi_pm >> pci 0000:00:1c.0: BAR 9: assigned [mem 0x80000000-0x801fffff pref] >> pci 0000:00:1c.1: BAR 9: assigned [mem 0x80200000-0x803fffff pref] >> -pci 0000:00:1c.0: BAR 7: assigned [io 0x1000-0x1fff] >> +pci 0000:00:1c.0: BAR 7: assigned [io 0x2000-0x2fff] >> pci 0000:02:01.0: PCI bridge to [bus 03] >> pci 0000:02:01.0: bridge window [mem 0xdff00000-0xdfffffff] >> pci 0000:01:00.0: PCI bridge to [bus 02-03] >> pci 0000:01:00.0: bridge window [mem 0xdff00000-0xdfffffff] >> pci 0000:00:1c.0: PCI bridge to [bus 01-03] >> -pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff] >> +pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff] >> pci 0000:00:1c.0: bridge window [mem 0xdff00000-0xdfffffff] >> pci 0000:00:1c.0: bridge window [mem 0x80000000-0x801fffff pref] >> pci 0000:00:1c.1: PCI bridge to [bus 04] >> >> I also noticed the kernel output 'ACPI: PM-Timer IO Port: 0x2008' and >> made the connection that since acpi_pm was being used as the >> clocksource and since the problems started when the BAR switched from >> 0x1000 to 0x2000 an I/O conflict must be the source of the problems. >> >> I did some reading into ACPI (since my understanding of it was novice >> at the time) and dumped the DSDT. I found no reference to anything in >> the 0x2xxx I/O range though I did find the following in the FADT: >> PM1a_EVT_BLK at 0x2000-0x2003 >> PM1a_CNT_BLK at 0x2004-0x2005 >> PM_TMR at 0x2008-0x200b >> >> I dumped the DSDT on other systems and found that some used PNP0C02 to >> reserve I/O ranges used by the ACPI PM registers. >> >> I added the following to the Versalogic Tiger dsdt.dsl under the PCI >> bus, compiled it and and compiled into the linux kernel: >> Device (PMIO) >> { >> Name (_HID, EisaId ("PNP0C02") /* PNP Motherboard >> Resources */) // _HID: Hardware ID >> Name (_UID, 0x09) // _UID: Unique ID >> Method (_CRS, 0, NotSerialized) // _CRS: Current >> Resource Settings >> { >> Name (BUF0, ResourceTemplate () >> { >> IO (Decode16, >> 0x2000, // Range Minimum >> 0x2000, // Range Maximum >> 0x01, // Alignment >> 0xC, // Length >> ) >> IO (Decode16, >> 0x20C0, // Range Minimum >> 0x20C0, // Range Maximum >> 0x01, // Alignment >> 0x8, // Length >> ) >> }) >> Return (BUF0) >> } >> } >> >> It booted just fine! (comment welcome on whether or not this looks >> like the correct fix) >> >> Unfortunately even if I get the vendor to release a new BIOS with the >> DSDT modifications, rolling out BIOS updates to thousands of systems >> in the field will be nearly impossible. When we roll out a new kernel >> to the production systems we'll need it to work with the existing >> BIOS. >> >> I've been searching around the linux kernel for a way to apply a quirk >> specific to this board. >> I've found I can do something like the following and match the Poulsbo >> Host bridge and that it'll fix the problem but I don't see a decent >> way of restricting it to this board. >> >> diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c >> index 85f247e..1f16dbf 100644 >> --- a/drivers/pci/quirks.c >> +++ b/drivers/pci/quirks.c >> @@ -413,6 +413,17 @@ static void quirk_ati_exploding_mce(struct pci_dev *dev) >> DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, >> PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce); >> >> /* >> + * Versa Logic Tiger >> + */ >> +static void quirk_versa_logic_tiger(struct pci_dev *dev) >> +{ >> + dev_info(&dev->dev, "Versalogic Tiger, reserving I/O ports\n"); >> + request_region(0x2000, 0x0C, "Versalogic Tiger"); >> + request_region(0x20C0, 0x08, "Versalogic Tiger"); >> +} >> +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x8100, quirk_versa_logic_tiger); >> + >> +/* >> >> Any suggestions on what could be done to get a fix for this board >> mainlined into the kernel? Should I give up hope and just apply a cute >> embedded non-sense hack? > > I think your DSDT tweak is on the right track. We have some similar > things in drivers/pnp/quirks.c. Possibly a new region could be added > to an existing PNP0C02 device, maybe via dmi_check_system() to limit > it to this platform. > > But I notice that board claims Windows compatibility, so I wonder if > there's a smarter way. I doubt that Windows would have a quirk for > this specific board, so we should be able to make Linux work without a > quirk, too. Maybe it works by accident, linux worked too until 0x2000 started getting used for the I/O window. Though I'm not sure why it changed just by looking at the commit. > > Complete dmesg logs from pre- and post-ac212b6980d8 might have a clue > about what changed. It looks like your FADT should be enough to > reserve those regions via acpi_reserve_resources(). But maybe there's > something wrong there, or maybe we incorrectly use that for PCI space. > Does your post-ac212b6980d8 /proc/ioports show those regions? I've attached the the last good and first bad dmesg logs. acpi_reserve_resources() doesn't do any good (at least in 4.1rc2) because it's called after pcieport has already enabled the device and put the i/o window into use. I wasn't able to get ac212b6980d8 to boot without making DSDT or quirks.c changes but I was able to get 4.1rc2 to boot by disabling PCIEPORTBUS which keeps 0000:00:1c.0 from being enabled. I've attached the ioports information. It looks like ACPI PM1a_EVT_BLK, ACPI PM1a_CNT_BLK and ACPI PM_TMR show up at 2000-2003, 2004-2005 and 2008-200b respectively but instead of conflicting with the PCI-bridge window they show up underneath it. I think the key here is that the region needs to be requested before bridge window is assigned. > > Bjorn -- To unsubscribe from this list: send the line "unsubscribe linux-acpi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Looks like the attachments didn't go through. I'll try them again. On Wed, May 6, 2015 at 2:15 PM, George McCollister <george.mccollister@gmail.com> wrote: > On Wed, May 6, 2015 at 10:51 AM, Bjorn Helgaas <bhelgaas@google.com> wrote: >> [+cc Rafael] >> >> On Wed, May 6, 2015 at 9:47 AM, George McCollister >> <george.mccollister@gmail.com> wrote: >>> We're using Versalogic Tiger (VL-EPM-24) SBCs in embedded systems >>> running linux 3.2.x without any problems. Recently, when testing the >>> latest mainline kernel I found the system hard locked during boot. >>> >>> After some investigation I noticed that the kernel print time stamps >>> were bogus after one of the pcieports was enabled: >>> [ 1.658879] io scheduler cfq registered (default) >>> [ 1.663905] pcieport 0000:00:1c.0: enabling device (0004 -> 0007) >>> [ 6.254134] Serial: 8250/16550 driver, 21 ports, IRQ sharing enabled >>> [ 6.254134] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) >>> is a 16550A >>> [ 6.254134] 00:04: ttyS1 at I/O 0x2f8 (irq = 0, base_baud = 115200) >>> is a 16550A >>> [ 6.254134] 00:05: ttyS2 at I/O 0x3e8 (irq = 0, base_baud = 115200) >>> is a 16550A >>> [ 6.254134] 00:06: ttyS4 at I/O 0x238 (irq = 0, base_baud = 115200) >>> is a 16550A >>> >>> I was surprised to find that the problem existed as far back as 3.11. >>> I checked to make sure we were using the latest BIOS and contacted the >>> vendor to see if they were aware of anyone else using recent versions >>> of the linux kernel. They stated that they were unaware of anyone >>> using recent kernel versions on this board and tired to convince me to >>> stick with an old version. >>> >>> I then git bisected to this commit: >>> ac212b6980d8d5eda705864fc5a8ecddc6d6eacc ACPI / processor: Use common >>> hotplug infrastructure >>> >>> After diffing the kernel output before and after this commit I noticed >>> that the I/O BAR assigned to the pcieport (same one as above) changed >>> from 0x1000 to 0x2000. >>> >>> @@ -191,13 +191,13 @@ >>> Switching to clocksource acpi_pm >>> pci 0000:00:1c.0: BAR 9: assigned [mem 0x80000000-0x801fffff pref] >>> pci 0000:00:1c.1: BAR 9: assigned [mem 0x80200000-0x803fffff pref] >>> -pci 0000:00:1c.0: BAR 7: assigned [io 0x1000-0x1fff] >>> +pci 0000:00:1c.0: BAR 7: assigned [io 0x2000-0x2fff] >>> pci 0000:02:01.0: PCI bridge to [bus 03] >>> pci 0000:02:01.0: bridge window [mem 0xdff00000-0xdfffffff] >>> pci 0000:01:00.0: PCI bridge to [bus 02-03] >>> pci 0000:01:00.0: bridge window [mem 0xdff00000-0xdfffffff] >>> pci 0000:00:1c.0: PCI bridge to [bus 01-03] >>> -pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff] >>> +pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff] >>> pci 0000:00:1c.0: bridge window [mem 0xdff00000-0xdfffffff] >>> pci 0000:00:1c.0: bridge window [mem 0x80000000-0x801fffff pref] >>> pci 0000:00:1c.1: PCI bridge to [bus 04] >>> >>> I also noticed the kernel output 'ACPI: PM-Timer IO Port: 0x2008' and >>> made the connection that since acpi_pm was being used as the >>> clocksource and since the problems started when the BAR switched from >>> 0x1000 to 0x2000 an I/O conflict must be the source of the problems. >>> >>> I did some reading into ACPI (since my understanding of it was novice >>> at the time) and dumped the DSDT. I found no reference to anything in >>> the 0x2xxx I/O range though I did find the following in the FADT: >>> PM1a_EVT_BLK at 0x2000-0x2003 >>> PM1a_CNT_BLK at 0x2004-0x2005 >>> PM_TMR at 0x2008-0x200b >>> >>> I dumped the DSDT on other systems and found that some used PNP0C02 to >>> reserve I/O ranges used by the ACPI PM registers. >>> >>> I added the following to the Versalogic Tiger dsdt.dsl under the PCI >>> bus, compiled it and and compiled into the linux kernel: >>> Device (PMIO) >>> { >>> Name (_HID, EisaId ("PNP0C02") /* PNP Motherboard >>> Resources */) // _HID: Hardware ID >>> Name (_UID, 0x09) // _UID: Unique ID >>> Method (_CRS, 0, NotSerialized) // _CRS: Current >>> Resource Settings >>> { >>> Name (BUF0, ResourceTemplate () >>> { >>> IO (Decode16, >>> 0x2000, // Range Minimum >>> 0x2000, // Range Maximum >>> 0x01, // Alignment >>> 0xC, // Length >>> ) >>> IO (Decode16, >>> 0x20C0, // Range Minimum >>> 0x20C0, // Range Maximum >>> 0x01, // Alignment >>> 0x8, // Length >>> ) >>> }) >>> Return (BUF0) >>> } >>> } >>> >>> It booted just fine! (comment welcome on whether or not this looks >>> like the correct fix) >>> >>> Unfortunately even if I get the vendor to release a new BIOS with the >>> DSDT modifications, rolling out BIOS updates to thousands of systems >>> in the field will be nearly impossible. When we roll out a new kernel >>> to the production systems we'll need it to work with the existing >>> BIOS. >>> >>> I've been searching around the linux kernel for a way to apply a quirk >>> specific to this board. >>> I've found I can do something like the following and match the Poulsbo >>> Host bridge and that it'll fix the problem but I don't see a decent >>> way of restricting it to this board. >>> >>> diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c >>> index 85f247e..1f16dbf 100644 >>> --- a/drivers/pci/quirks.c >>> +++ b/drivers/pci/quirks.c >>> @@ -413,6 +413,17 @@ static void quirk_ati_exploding_mce(struct pci_dev *dev) >>> DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, >>> PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce); >>> >>> /* >>> + * Versa Logic Tiger >>> + */ >>> +static void quirk_versa_logic_tiger(struct pci_dev *dev) >>> +{ >>> + dev_info(&dev->dev, "Versalogic Tiger, reserving I/O ports\n"); >>> + request_region(0x2000, 0x0C, "Versalogic Tiger"); >>> + request_region(0x20C0, 0x08, "Versalogic Tiger"); >>> +} >>> +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x8100, quirk_versa_logic_tiger); >>> + >>> +/* >>> >>> Any suggestions on what could be done to get a fix for this board >>> mainlined into the kernel? Should I give up hope and just apply a cute >>> embedded non-sense hack? >> >> I think your DSDT tweak is on the right track. We have some similar >> things in drivers/pnp/quirks.c. Possibly a new region could be added >> to an existing PNP0C02 device, maybe via dmi_check_system() to limit >> it to this platform. >> >> But I notice that board claims Windows compatibility, so I wonder if >> there's a smarter way. I doubt that Windows would have a quirk for >> this specific board, so we should be able to make Linux work without a >> quirk, too. > Maybe it works by accident, linux worked too until 0x2000 started > getting used for the I/O window. Though I'm not sure why it changed > just by looking at the commit. >> >> Complete dmesg logs from pre- and post-ac212b6980d8 might have a clue >> about what changed. It looks like your FADT should be enough to >> reserve those regions via acpi_reserve_resources(). But maybe there's >> something wrong there, or maybe we incorrectly use that for PCI space. >> Does your post-ac212b6980d8 /proc/ioports show those regions? > I've attached the the last good and first bad dmesg logs. > acpi_reserve_resources() doesn't do any good (at least in 4.1rc2) > because it's called after pcieport has already enabled the device and > put the i/o window into use. > I wasn't able to get ac212b6980d8 to boot without making DSDT or > quirks.c changes but I was able to get 4.1rc2 to boot by disabling > PCIEPORTBUS which keeps 0000:00:1c.0 from being enabled. I've attached > the ioports information. It looks like ACPI PM1a_EVT_BLK, ACPI > PM1a_CNT_BLK and ACPI PM_TMR show up at 2000-2003, 2004-2005 and > 2008-200b respectively but instead of conflicting with the PCI-bridge > window they show up underneath it. > > I think the key here is that the region needs to be requested before > bridge window is assigned. >> >> Bjorn # cat /proc/ioports 0000-0cf7 : PCI Bus 0000:00 0000-001f : dma1 0020-0021 : pic1 0040-0043 : timer0 0050-0053 : timer1 0060-0060 : keyboard 0061-0061 : PNP0800:00 0064-0064 : keyboard 0070-0077 : rtc0 0080-008f : dma page reg 00a0-00a1 : pic2 00c0-00df : dma2 00f0-00ff : PNP0C04:00 00f0-00ff : fpu 0100-0107 : serial 0108-010f : serial 0110-0117 : serial 0118-011f : serial 0120-0127 : serial 0128-012f : serial 0130-0137 : serial 0138-013f : serial 0170-0177 : 0000:00:1f.1 0170-0177 : pata_sch 01f0-01f7 : 0000:00:1f.1 01f0-01f7 : pata_sch 02e8-02ef : serial 02f8-02ff : serial 0310-0317 : serial 0318-031f : serial 0320-0327 : serial 0328-032f : serial 0330-0337 : serial 0338-033f : serial 0340-0347 : serial 0348-034f : serial 0376-0376 : 0000:00:1f.1 0376-0376 : pata_sch 03c0-03df : vga+ 03e8-03ef : serial 03f6-03f6 : 0000:00:1f.1 03f6-03f6 : pata_sch 03f8-03ff : serial 0500-053f : sch_gpio.33049 0c00-0c7f : pnp 00:02 0c70-0c71 : dme1737 0c70-0c71 : dme1737 0cf8-0cff : PCI conf1 0d00-ffff : PCI Bus 0000:00 1010-1015 : ACPI CPU throttle 2000-2fff : PCI Bus 0000:01 2000-2003 : ACPI PM1a_EVT_BLK 2004-2005 : ACPI PM1a_CNT_BLK 2008-200b : ACPI PM_TMR 2040-207f : isch_smbus.33049 2040-207f : isch_smbus 20c0-20c7 : ACPI GPE0_BLK ec88-ec8f : 0000:00:02.0 ec90-ec9f : 0000:00:1f.1 ec90-ec9f : pata_sch eca0-ecbf : 0000:00:1d.0 eca0-ecbf : uhci_hcd ecc0-ecdf : 0000:00:1d.1 ecc0-ecdf : uhci_hcd ece0-ecff : 0000:00:1d.2 ece0-ecff : uhci_hcd f000-ffff : PCI Bus 0000:03 fce0-fcff : 0000:03:00.0
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index 85f247e..1f16dbf 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -413,6 +413,17 @@ static void quirk_ati_exploding_mce(struct pci_dev *dev) DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce); /* + * Versa Logic Tiger + */ +static void quirk_versa_logic_tiger(struct pci_dev *dev) +{ + dev_info(&dev->dev, "Versalogic Tiger, reserving I/O ports\n"); + request_region(0x2000, 0x0C, "Versalogic Tiger"); + request_region(0x20C0, 0x08, "Versalogic Tiger"); +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x8100, quirk_versa_logic_tiger); + +/* Any suggestions on what could be done to get a fix for this board
We're using Versalogic Tiger (VL-EPM-24) SBCs in embedded systems running linux 3.2.x without any problems. Recently, when testing the latest mainline kernel I found the system hard locked during boot. After some investigation I noticed that the kernel print time stamps were bogus after one of the pcieports was enabled: [ 1.658879] io scheduler cfq registered (default) [ 1.663905] pcieport 0000:00:1c.0: enabling device (0004 -> 0007) [ 6.254134] Serial: 8250/16550 driver, 21 ports, IRQ sharing enabled [ 6.254134] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 6.254134] 00:04: ttyS1 at I/O 0x2f8 (irq = 0, base_baud = 115200) is a 16550A [ 6.254134] 00:05: ttyS2 at I/O 0x3e8 (irq = 0, base_baud = 115200) is a 16550A [ 6.254134] 00:06: ttyS4 at I/O 0x238 (irq = 0, base_baud = 115200) is a 16550A I was surprised to find that the problem existed as far back as 3.11. I checked to make sure we were using the latest BIOS and contacted the vendor to see if they were aware of anyone else using recent versions of the linux kernel. They stated that they were unaware of anyone using recent kernel versions on this board and tired to convince me to stick with an old version. I then git bisected to this commit: ac212b6980d8d5eda705864fc5a8ecddc6d6eacc ACPI / processor: Use common hotplug infrastructure After diffing the kernel output before and after this commit I noticed that the I/O BAR assigned to the pcieport (same one as above) changed from 0x1000 to 0x2000. @@ -191,13 +191,13 @@ Switching to clocksource acpi_pm pci 0000:00:1c.0: BAR 9: assigned [mem 0x80000000-0x801fffff pref] pci 0000:00:1c.1: BAR 9: assigned [mem 0x80200000-0x803fffff pref] -pci 0000:00:1c.0: BAR 7: assigned [io 0x1000-0x1fff] +pci 0000:00:1c.0: BAR 7: assigned [io 0x2000-0x2fff] pci 0000:02:01.0: PCI bridge to [bus 03] pci 0000:02:01.0: bridge window [mem 0xdff00000-0xdfffffff] pci 0000:01:00.0: PCI bridge to [bus 02-03] pci 0000:01:00.0: bridge window [mem 0xdff00000-0xdfffffff] pci 0000:00:1c.0: PCI bridge to [bus 01-03] -pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff] +pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff] pci 0000:00:1c.0: bridge window [mem 0xdff00000-0xdfffffff] pci 0000:00:1c.0: bridge window [mem 0x80000000-0x801fffff pref] pci 0000:00:1c.1: PCI bridge to [bus 04] I also noticed the kernel output 'ACPI: PM-Timer IO Port: 0x2008' and made the connection that since acpi_pm was being used as the clocksource and since the problems started when the BAR switched from 0x1000 to 0x2000 an I/O conflict must be the source of the problems. I did some reading into ACPI (since my understanding of it was novice at the time) and dumped the DSDT. I found no reference to anything in the 0x2xxx I/O range though I did find the following in the FADT: PM1a_EVT_BLK at 0x2000-0x2003 PM1a_CNT_BLK at 0x2004-0x2005 PM_TMR at 0x2008-0x200b I dumped the DSDT on other systems and found that some used PNP0C02 to reserve I/O ranges used by the ACPI PM registers. I added the following to the Versalogic Tiger dsdt.dsl under the PCI bus, compiled it and and compiled into the linux kernel: Device (PMIO) { Name (_HID, EisaId ("PNP0C02") /* PNP Motherboard Resources */) // _HID: Hardware ID Name (_UID, 0x09) // _UID: Unique ID Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings { Name (BUF0, ResourceTemplate () { IO (Decode16, 0x2000, // Range Minimum 0x2000, // Range Maximum 0x01, // Alignment 0xC, // Length ) IO (Decode16, 0x20C0, // Range Minimum 0x20C0, // Range Maximum 0x01, // Alignment 0x8, // Length ) }) Return (BUF0) } } It booted just fine! (comment welcome on whether or not this looks like the correct fix) Unfortunately even if I get the vendor to release a new BIOS with the DSDT modifications, rolling out BIOS updates to thousands of systems in the field will be nearly impossible. When we roll out a new kernel to the production systems we'll need it to work with the existing BIOS. I've been searching around the linux kernel for a way to apply a quirk specific to this board. I've found I can do something like the following and match the Poulsbo Host bridge and that it'll fix the problem but I don't see a decent way of restricting it to this board. mainlined into the kernel? Should I give up hope and just apply a cute embedded non-sense hack? Thanks, George McCollister -- To unsubscribe from this list: send the line "unsubscribe linux-acpi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html