| Message ID | 1432304206-18765-1-git-send-email-hali@codeaurora.org (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Delegated to: | Andy Gross |
| Headers | show |
On 05/22/2015 07:46 PM, Hai Li wrote: > DSI video mode engine can only take active-high sync signals. This > change prevents MDP5 sending active-low sync signals to DSI in any > case. > > Signed-off-by: Hai Li <hali@codeaurora.org> Tested-by: Archit Taneja <architt@codeaurora.org> > --- > drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c | 12 ++++++++---- > 1 file changed, 8 insertions(+), 4 deletions(-) > > diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c > index 53bb1f7..2e98ce0 100644 > --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c > +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c > @@ -144,10 +144,14 @@ static void mdp5_encoder_mode_set(struct drm_encoder *encoder, > mode->type, mode->flags); > > ctrl_pol = 0; > - if (mode->flags & DRM_MODE_FLAG_NHSYNC) > - ctrl_pol |= MDP5_INTF_POLARITY_CTL_HSYNC_LOW; > - if (mode->flags & DRM_MODE_FLAG_NVSYNC) > - ctrl_pol |= MDP5_INTF_POLARITY_CTL_VSYNC_LOW; > + > + /* DSI controller cannot handle active-low sync signals. */ > + if (mdp5_encoder->intf.type != INTF_DSI) { > + if (mode->flags & DRM_MODE_FLAG_NHSYNC) > + ctrl_pol |= MDP5_INTF_POLARITY_CTL_HSYNC_LOW; > + if (mode->flags & DRM_MODE_FLAG_NVSYNC) > + ctrl_pol |= MDP5_INTF_POLARITY_CTL_VSYNC_LOW; > + } > /* probably need to get DATA_EN polarity from panel.. */ > > dtv_hsync_skew = 0; /* get this from panel? */ >
diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c index 53bb1f7..2e98ce0 100644 --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c @@ -144,10 +144,14 @@ static void mdp5_encoder_mode_set(struct drm_encoder *encoder, mode->type, mode->flags); ctrl_pol = 0; - if (mode->flags & DRM_MODE_FLAG_NHSYNC) - ctrl_pol |= MDP5_INTF_POLARITY_CTL_HSYNC_LOW; - if (mode->flags & DRM_MODE_FLAG_NVSYNC) - ctrl_pol |= MDP5_INTF_POLARITY_CTL_VSYNC_LOW; + + /* DSI controller cannot handle active-low sync signals. */ + if (mdp5_encoder->intf.type != INTF_DSI) { + if (mode->flags & DRM_MODE_FLAG_NHSYNC) + ctrl_pol |= MDP5_INTF_POLARITY_CTL_HSYNC_LOW; + if (mode->flags & DRM_MODE_FLAG_NVSYNC) + ctrl_pol |= MDP5_INTF_POLARITY_CTL_VSYNC_LOW; + } /* probably need to get DATA_EN polarity from panel.. */ dtv_hsync_skew = 0; /* get this from panel? */
DSI video mode engine can only take active-high sync signals. This change prevents MDP5 sending active-low sync signals to DSI in any case. Signed-off-by: Hai Li <hali@codeaurora.org> --- drivers/gpu/drm/msm/mdp/mdp5/mdp5_encoder.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-)