Message ID | 1436522405-13923-5-git-send-email-jamesjj.liao@mediatek.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
Hi James, On Fri, Jul 10, 2015 at 6:00 PM, James Liao <jamesjj.liao@mediatek.com> wrote: > Add REF2USB_TX clock support into MT8173 APMIXEDSYS. This clock > is needed by USB 3.0. > > Signed-off-by: James Liao <jamesjj.liao@mediatek.com> > --- > drivers/clk/mediatek/clk-mt8173.c | 143 +++++++++++++++++++++++++++++++++ > drivers/clk/mediatek/clk-pll.c | 7 +- > include/dt-bindings/clock/mt8173-clk.h | 3 +- > 3 files changed, 146 insertions(+), 7 deletions(-) > > diff --git a/drivers/clk/mediatek/clk-mt8173.c b/drivers/clk/mediatek/clk-mt8173.c > index 1d21e26..11f82cb 100644 > --- a/drivers/clk/mediatek/clk-mt8173.c > +++ b/drivers/clk/mediatek/clk-mt8173.c > @@ -12,6 +12,7 @@ > * GNU General Public License for more details. > */ > > +#include <linux/delay.h> > #include <linux/of.h> > #include <linux/of_address.h> > #include <linux/slab.h> > @@ -968,6 +969,141 @@ static void __init mtk_pericfg_init(struct device_node *node) > } > CLK_OF_DECLARE(mtk_pericfg, "mediatek,mt8173-pericfg", mtk_pericfg_init); > > +#define REF2USB_TX_EN BIT(0) > +#define REF2USB_TX_LPF_EN BIT(1) > +#define REF2USB_TX_OUT_EN BIT(2) > +#define REF2USB_EN_MASK (REF2USB_TX_EN | REF2USB_TX_LPF_EN | \ > + REF2USB_TX_OUT_EN) > + > +struct mtk_ref2usb_tx { > + struct clk_hw hw; > + void __iomem *base_addr; > +}; > + > +static inline struct mtk_ref2usb_tx *to_mtk_ref2usb_tx(struct clk_hw *hw) > +{ > + return container_of(hw, struct mtk_ref2usb_tx, hw); > +} > + > +static int mtk_ref2usb_tx_is_prepared(struct clk_hw *hw) > +{ > + struct mtk_ref2usb_tx *tx = to_mtk_ref2usb_tx(hw); > + > + return (readl(tx->base_addr) & REF2USB_EN_MASK) == REF2USB_EN_MASK; > +} > + > +static int mtk_ref2usb_tx_prepare(struct clk_hw *hw) > +{ > + struct mtk_ref2usb_tx *tx = to_mtk_ref2usb_tx(hw); > + u32 val; > + > + val = readl(tx->base_addr); > + > + val |= REF2USB_TX_EN; > + writel(val, tx->base_addr); > + udelay(100); > + > + val |= REF2USB_TX_LPF_EN; > + writel(val, tx->base_addr); > + > + val |= REF2USB_TX_OUT_EN; > + writel(val, tx->base_addr); > + > + return 0; > +} > + > +static void mtk_ref2usb_tx_unprepare(struct clk_hw *hw) > +{ > + struct mtk_ref2usb_tx *tx = to_mtk_ref2usb_tx(hw); > + u32 val; > + > + val = readl(tx->base_addr); > + val &= ~REF2USB_EN_MASK; > + writel(val, tx->base_addr); > +} > + > +static const struct clk_ops mtk_ref2usb_tx_ops = { > + .is_prepared = mtk_ref2usb_tx_is_prepared, > + .prepare = mtk_ref2usb_tx_prepare, > + .unprepare = mtk_ref2usb_tx_unprepare, > +}; Burying the implementation of this special "mtk_ref2usb" clock in clk-mt8173,c seems a bit awkward. Can you please move it to its own file, like mediatek/clk-usb.c? > + > +static struct clk *mtk_clk_register_ref2usb_tx(const char *name, > + const char *parent_name, void __iomem *reg) > +{ > + struct mtk_ref2usb_tx *tx; > + struct clk_init_data init = {}; > + struct clk *clk; > + > + tx = kzalloc(sizeof(*tx), GFP_KERNEL); > + if (!tx) > + return ERR_PTR(-ENOMEM); > + > + tx->base_addr = reg; > + tx->hw.init = &init; > + > + init.name = name; > + init.ops = &mtk_ref2usb_tx_ops; > + init.parent_names = &parent_name; > + init.num_parents = 1; > + > + clk = clk_register(NULL, &tx->hw); > + > + if (IS_ERR(clk)) { > + pr_err("Failed to register clk %s: %ld\n", name, PTR_ERR(clk)); > + kfree(tx); > + } > + > + return clk; > +} > + > +struct mtk_apmixed_ex { > + int id; > + const char *name; > + const char *parent; > + u32 reg_ofs; > +}; > + > +#define APMIXED_EX(_id, _name, _parent, _reg_ofs) { \ > + .id = _id, \ > + .name = _name, \ > + .parent = _parent, \ > + .reg_ofs = _reg_ofs, \ > + } > + > +static const struct mtk_apmixed_ex apmixed_ex[] = { __initconst > + APMIXED_EX(CLK_APMIXED_REF2USB_TX, "ref2usb_tx", "clk26m", 0x8), > +}; > + > +static void __init mtk_clk_register_apmixedsys_special(struct device_node *node, > + struct clk_onecell_data *clk_data) > +{ > + void __iomem *base; > + struct clk *clk; > + int i; > + > + base = of_iomap(node, 0); > + if (!base) { > + pr_err("%s(): ioremap failed\n", __func__); > + return; > + } > + > + for (i = 0; i < ARRAY_SIZE(apmixed_ex); i++) { > + const struct mtk_apmixed_ex *ape = &apmixed_ex[i]; > + > + clk = mtk_clk_register_ref2usb_tx(ape->name, ape->parent, > + base + ape->reg_ofs); > + > + if (IS_ERR(clk)) { > + pr_err("Failed to register clk %s: %ld\n", ape->name, > + PTR_ERR(clk)); > + continue; > + } > + > + clk_data->clks[CLK_APMIXED_REF2USB_TX] = clk; This works assuming ARRAY_SIZE(apmixed_ex) == 1. Either remove the loop since it is unnecessary, or do: clk_data->clks[ape->id] = clk; > + } > +} > + > #define MT8173_PLL_FMAX (3000UL * MHZ) > > #define CON0_MT8173_RST_BAR BIT(24) > @@ -1010,12 +1146,19 @@ static const struct mtk_pll_data plls[] = { > static void __init mtk_apmixedsys_init(struct device_node *node) > { > struct clk_onecell_data *clk_data; > + int r; > > mt8173_pll_clk_data = clk_data = mtk_alloc_clk_data(CLK_APMIXED_NR_CLK); > if (!clk_data) > return; > > mtk_clk_register_plls(node, plls, ARRAY_SIZE(plls), clk_data); > + mtk_clk_register_apmixedsys_special(node, clk_data); > + > + r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); > + if (r) > + pr_err("%s(): could not register clock provider: %d\n", > + __func__, r); > > mtk_clk_enable_critical(); > } > diff --git a/drivers/clk/mediatek/clk-pll.c b/drivers/clk/mediatek/clk-pll.c > index 44409e9..813f0c7 100644 > --- a/drivers/clk/mediatek/clk-pll.c > +++ b/drivers/clk/mediatek/clk-pll.c > @@ -302,7 +302,7 @@ void __init mtk_clk_register_plls(struct device_node *node, > const struct mtk_pll_data *plls, int num_plls, struct clk_onecell_data *clk_data) > { > void __iomem *base; > - int r, i; > + int i; > struct clk *clk; > > base = of_iomap(node, 0); > @@ -324,9 +324,4 @@ void __init mtk_clk_register_plls(struct device_node *node, > > clk_data->clks[pll->id] = clk; > } > - > - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); > - if (r) > - pr_err("%s(): could not register clock provider: %d\n", > - __func__, r); > } > diff --git a/include/dt-bindings/clock/mt8173-clk.h b/include/dt-bindings/clock/mt8173-clk.h > index 6ce88bf..7b7c555 100644 > --- a/include/dt-bindings/clock/mt8173-clk.h > +++ b/include/dt-bindings/clock/mt8173-clk.h > @@ -172,7 +172,8 @@ > #define CLK_APMIXED_APLL2 12 > #define CLK_APMIXED_LVDSPLL 13 > #define CLK_APMIXED_MSDCPLL2 14 > -#define CLK_APMIXED_NR_CLK 15 > +#define CLK_APMIXED_REF2USB_TX 15 > +#define CLK_APMIXED_NR_CLK 16 > > /* INFRA_SYS */ > > -- > 1.8.1.1.dirty >
Hi Daniel, On Mon, 2015-07-13 at 22:46 +0800, Daniel Kurtz wrote: > > +static const struct clk_ops mtk_ref2usb_tx_ops = { > > + .is_prepared = mtk_ref2usb_tx_is_prepared, > > + .prepare = mtk_ref2usb_tx_prepare, > > + .unprepare = mtk_ref2usb_tx_unprepare, > > +}; > > Burying the implementation of this special "mtk_ref2usb" clock in > clk-mt8173,c seems a bit awkward. > Can you please move it to its own file, like mediatek/clk-usb.c? Do you mean clk/mediatek/clk-usb.c? This clock is a MT8173 specific clock, which may not be reused by other SoCs. So I think it's not necessary to move it to a separated file. > > + > > +static struct clk *mtk_clk_register_ref2usb_tx(const char *name, > > + const char *parent_name, void __iomem *reg) > > +{ > > + struct mtk_ref2usb_tx *tx; > > + struct clk_init_data init = {}; > > + struct clk *clk; > > + > > + tx = kzalloc(sizeof(*tx), GFP_KERNEL); > > + if (!tx) > > + return ERR_PTR(-ENOMEM); > > + > > + tx->base_addr = reg; > > + tx->hw.init = &init; > > + > > + init.name = name; > > + init.ops = &mtk_ref2usb_tx_ops; > > + init.parent_names = &parent_name; > > + init.num_parents = 1; > > + > > + clk = clk_register(NULL, &tx->hw); > > + > > + if (IS_ERR(clk)) { > > + pr_err("Failed to register clk %s: %ld\n", name, PTR_ERR(clk)); > > + kfree(tx); > > + } > > + > > + return clk; > > +} > > + > > +struct mtk_apmixed_ex { > > + int id; > > + const char *name; > > + const char *parent; > > + u32 reg_ofs; > > +}; > > + > > +#define APMIXED_EX(_id, _name, _parent, _reg_ofs) { \ > > + .id = _id, \ > > + .name = _name, \ > > + .parent = _parent, \ > > + .reg_ofs = _reg_ofs, \ > > + } > > + > > +static const struct mtk_apmixed_ex apmixed_ex[] = { > > __initconst OK. I'll fix it in next patch. > > + APMIXED_EX(CLK_APMIXED_REF2USB_TX, "ref2usb_tx", "clk26m", 0x8), > > +}; > > + > > +static void __init mtk_clk_register_apmixedsys_special(struct device_node *node, > > + struct clk_onecell_data *clk_data) > > +{ > > + void __iomem *base; > > + struct clk *clk; > > + int i; > > + > > + base = of_iomap(node, 0); > > + if (!base) { > > + pr_err("%s(): ioremap failed\n", __func__); > > + return; > > + } > > + > > + for (i = 0; i < ARRAY_SIZE(apmixed_ex); i++) { > > + const struct mtk_apmixed_ex *ape = &apmixed_ex[i]; > > + > > + clk = mtk_clk_register_ref2usb_tx(ape->name, ape->parent, > > + base + ape->reg_ofs); > > + > > + if (IS_ERR(clk)) { > > + pr_err("Failed to register clk %s: %ld\n", ape->name, > > + PTR_ERR(clk)); > > + continue; > > + } > > + > > + clk_data->clks[CLK_APMIXED_REF2USB_TX] = clk; > > This works assuming ARRAY_SIZE(apmixed_ex) == 1. > Either remove the loop since it is unnecessary, or do: > clk_data->clks[ape->id] = clk; It should be "clk_data->clks[ape->id] = clk". I'll fix it in next patch. Best regards, James
On Tue, Jul 14, 2015 at 10:45 AM, James Liao <jamesjj.liao@mediatek.com> wrote: > Hi Daniel, > > On Mon, 2015-07-13 at 22:46 +0800, Daniel Kurtz wrote: > >> > +static const struct clk_ops mtk_ref2usb_tx_ops = { >> > + .is_prepared = mtk_ref2usb_tx_is_prepared, >> > + .prepare = mtk_ref2usb_tx_prepare, >> > + .unprepare = mtk_ref2usb_tx_unprepare, >> > +}; >> >> Burying the implementation of this special "mtk_ref2usb" clock in >> clk-mt8173,c seems a bit awkward. >> Can you please move it to its own file, like mediatek/clk-usb.c? > > Do you mean clk/mediatek/clk-usb.c? > > This clock is a MT8173 specific clock, which may not be reused by other > SoCs. So I think it's not necessary to move it to a separated file. Yes, this is a wrapper for a type of clock. I think it would be better in its own file, rather than embedded in clk-mt8173.c, which is more about enumerating and initializing the clock tree. Perhaps today it is only used for mt8173, but that may not be the case in the future. -Dan > >> > + >> > +static struct clk *mtk_clk_register_ref2usb_tx(const char *name, >> > + const char *parent_name, void __iomem *reg) >> > +{ >> > + struct mtk_ref2usb_tx *tx; >> > + struct clk_init_data init = {}; >> > + struct clk *clk; >> > + >> > + tx = kzalloc(sizeof(*tx), GFP_KERNEL); >> > + if (!tx) >> > + return ERR_PTR(-ENOMEM); >> > + >> > + tx->base_addr = reg; >> > + tx->hw.init = &init; >> > + >> > + init.name = name; >> > + init.ops = &mtk_ref2usb_tx_ops; >> > + init.parent_names = &parent_name; >> > + init.num_parents = 1; >> > + >> > + clk = clk_register(NULL, &tx->hw); >> > + >> > + if (IS_ERR(clk)) { >> > + pr_err("Failed to register clk %s: %ld\n", name, PTR_ERR(clk)); >> > + kfree(tx); >> > + } >> > + >> > + return clk; >> > +} >> > + >> > +struct mtk_apmixed_ex { >> > + int id; >> > + const char *name; >> > + const char *parent; >> > + u32 reg_ofs; >> > +}; >> > + >> > +#define APMIXED_EX(_id, _name, _parent, _reg_ofs) { \ >> > + .id = _id, \ >> > + .name = _name, \ >> > + .parent = _parent, \ >> > + .reg_ofs = _reg_ofs, \ >> > + } >> > + >> > +static const struct mtk_apmixed_ex apmixed_ex[] = { >> >> __initconst > > OK. I'll fix it in next patch. > >> > + APMIXED_EX(CLK_APMIXED_REF2USB_TX, "ref2usb_tx", "clk26m", 0x8), >> > +}; >> > + >> > +static void __init mtk_clk_register_apmixedsys_special(struct device_node *node, >> > + struct clk_onecell_data *clk_data) >> > +{ >> > + void __iomem *base; >> > + struct clk *clk; >> > + int i; >> > + >> > + base = of_iomap(node, 0); >> > + if (!base) { >> > + pr_err("%s(): ioremap failed\n", __func__); >> > + return; >> > + } >> > + >> > + for (i = 0; i < ARRAY_SIZE(apmixed_ex); i++) { >> > + const struct mtk_apmixed_ex *ape = &apmixed_ex[i]; >> > + >> > + clk = mtk_clk_register_ref2usb_tx(ape->name, ape->parent, >> > + base + ape->reg_ofs); >> > + >> > + if (IS_ERR(clk)) { >> > + pr_err("Failed to register clk %s: %ld\n", ape->name, >> > + PTR_ERR(clk)); >> > + continue; >> > + } >> > + >> > + clk_data->clks[CLK_APMIXED_REF2USB_TX] = clk; >> >> This works assuming ARRAY_SIZE(apmixed_ex) == 1. >> Either remove the loop since it is unnecessary, or do: >> clk_data->clks[ape->id] = clk; > > It should be "clk_data->clks[ape->id] = clk". I'll fix it in next patch. > > > Best regards, > > James >
Hi Daniel, On Tue, 2015-07-14 at 11:23 +0800, Daniel Kurtz wrote: > On Tue, Jul 14, 2015 at 10:45 AM, James Liao <jamesjj.liao@mediatek.com> wrote: > > On Mon, 2015-07-13 at 22:46 +0800, Daniel Kurtz wrote: > >> > +static const struct clk_ops mtk_ref2usb_tx_ops = { > >> > + .is_prepared = mtk_ref2usb_tx_is_prepared, > >> > + .prepare = mtk_ref2usb_tx_prepare, > >> > + .unprepare = mtk_ref2usb_tx_unprepare, > >> > +}; > >> > >> Burying the implementation of this special "mtk_ref2usb" clock in > >> clk-mt8173,c seems a bit awkward. > >> Can you please move it to its own file, like mediatek/clk-usb.c? > > > > Do you mean clk/mediatek/clk-usb.c? > > > > This clock is a MT8173 specific clock, which may not be reused by other > > SoCs. So I think it's not necessary to move it to a separated file. > > Yes, this is a wrapper for a type of clock. I think it would be > better in its own file, rather than embedded in clk-mt8173.c, which is > more about enumerating and initializing the clock tree. > > Perhaps today it is only used for mt8173, but that may not be the case > in the future. OK, I'll separate it from clk-mt8173.c. Ref2usb_tx's control register is located in APMIXEDSYS, which contains most of PLL controlling. Is this clock suitable to implemented mtk-pll.c? Or it's proper to be a separated file such as clk-usb.c? Best regards, James
On Tue, Jul 14, 2015 at 5:46 PM, James Liao <jamesjj.liao@mediatek.com> wrote: > Hi Daniel, > > On Tue, 2015-07-14 at 11:23 +0800, Daniel Kurtz wrote: >> On Tue, Jul 14, 2015 at 10:45 AM, James Liao <jamesjj.liao@mediatek.com> wrote: >> > On Mon, 2015-07-13 at 22:46 +0800, Daniel Kurtz wrote: >> >> > +static const struct clk_ops mtk_ref2usb_tx_ops = { >> >> > + .is_prepared = mtk_ref2usb_tx_is_prepared, >> >> > + .prepare = mtk_ref2usb_tx_prepare, >> >> > + .unprepare = mtk_ref2usb_tx_unprepare, >> >> > +}; >> >> >> >> Burying the implementation of this special "mtk_ref2usb" clock in >> >> clk-mt8173,c seems a bit awkward. >> >> Can you please move it to its own file, like mediatek/clk-usb.c? >> > >> > Do you mean clk/mediatek/clk-usb.c? >> > >> > This clock is a MT8173 specific clock, which may not be reused by other >> > SoCs. So I think it's not necessary to move it to a separated file. >> >> Yes, this is a wrapper for a type of clock. I think it would be >> better in its own file, rather than embedded in clk-mt8173.c, which is >> more about enumerating and initializing the clock tree. >> >> Perhaps today it is only used for mt8173, but that may not be the case >> in the future. > > OK, I'll separate it from clk-mt8173.c. > > Ref2usb_tx's control register is located in APMIXEDSYS, which contains > most of PLL controlling. Is this clock suitable to implemented > mtk-pll.c? Or it's proper to be a separated file such as clk-usb.c? I think a separate clk-usb.c might be better since the driver is very different than what is used for the PLLs. Thanks! -Dan > Best regards, > > James > >
diff --git a/drivers/clk/mediatek/clk-mt8173.c b/drivers/clk/mediatek/clk-mt8173.c index 1d21e26..11f82cb 100644 --- a/drivers/clk/mediatek/clk-mt8173.c +++ b/drivers/clk/mediatek/clk-mt8173.c @@ -12,6 +12,7 @@ * GNU General Public License for more details. */ +#include <linux/delay.h> #include <linux/of.h> #include <linux/of_address.h> #include <linux/slab.h> @@ -968,6 +969,141 @@ static void __init mtk_pericfg_init(struct device_node *node) } CLK_OF_DECLARE(mtk_pericfg, "mediatek,mt8173-pericfg", mtk_pericfg_init); +#define REF2USB_TX_EN BIT(0) +#define REF2USB_TX_LPF_EN BIT(1) +#define REF2USB_TX_OUT_EN BIT(2) +#define REF2USB_EN_MASK (REF2USB_TX_EN | REF2USB_TX_LPF_EN | \ + REF2USB_TX_OUT_EN) + +struct mtk_ref2usb_tx { + struct clk_hw hw; + void __iomem *base_addr; +}; + +static inline struct mtk_ref2usb_tx *to_mtk_ref2usb_tx(struct clk_hw *hw) +{ + return container_of(hw, struct mtk_ref2usb_tx, hw); +} + +static int mtk_ref2usb_tx_is_prepared(struct clk_hw *hw) +{ + struct mtk_ref2usb_tx *tx = to_mtk_ref2usb_tx(hw); + + return (readl(tx->base_addr) & REF2USB_EN_MASK) == REF2USB_EN_MASK; +} + +static int mtk_ref2usb_tx_prepare(struct clk_hw *hw) +{ + struct mtk_ref2usb_tx *tx = to_mtk_ref2usb_tx(hw); + u32 val; + + val = readl(tx->base_addr); + + val |= REF2USB_TX_EN; + writel(val, tx->base_addr); + udelay(100); + + val |= REF2USB_TX_LPF_EN; + writel(val, tx->base_addr); + + val |= REF2USB_TX_OUT_EN; + writel(val, tx->base_addr); + + return 0; +} + +static void mtk_ref2usb_tx_unprepare(struct clk_hw *hw) +{ + struct mtk_ref2usb_tx *tx = to_mtk_ref2usb_tx(hw); + u32 val; + + val = readl(tx->base_addr); + val &= ~REF2USB_EN_MASK; + writel(val, tx->base_addr); +} + +static const struct clk_ops mtk_ref2usb_tx_ops = { + .is_prepared = mtk_ref2usb_tx_is_prepared, + .prepare = mtk_ref2usb_tx_prepare, + .unprepare = mtk_ref2usb_tx_unprepare, +}; + +static struct clk *mtk_clk_register_ref2usb_tx(const char *name, + const char *parent_name, void __iomem *reg) +{ + struct mtk_ref2usb_tx *tx; + struct clk_init_data init = {}; + struct clk *clk; + + tx = kzalloc(sizeof(*tx), GFP_KERNEL); + if (!tx) + return ERR_PTR(-ENOMEM); + + tx->base_addr = reg; + tx->hw.init = &init; + + init.name = name; + init.ops = &mtk_ref2usb_tx_ops; + init.parent_names = &parent_name; + init.num_parents = 1; + + clk = clk_register(NULL, &tx->hw); + + if (IS_ERR(clk)) { + pr_err("Failed to register clk %s: %ld\n", name, PTR_ERR(clk)); + kfree(tx); + } + + return clk; +} + +struct mtk_apmixed_ex { + int id; + const char *name; + const char *parent; + u32 reg_ofs; +}; + +#define APMIXED_EX(_id, _name, _parent, _reg_ofs) { \ + .id = _id, \ + .name = _name, \ + .parent = _parent, \ + .reg_ofs = _reg_ofs, \ + } + +static const struct mtk_apmixed_ex apmixed_ex[] = { + APMIXED_EX(CLK_APMIXED_REF2USB_TX, "ref2usb_tx", "clk26m", 0x8), +}; + +static void __init mtk_clk_register_apmixedsys_special(struct device_node *node, + struct clk_onecell_data *clk_data) +{ + void __iomem *base; + struct clk *clk; + int i; + + base = of_iomap(node, 0); + if (!base) { + pr_err("%s(): ioremap failed\n", __func__); + return; + } + + for (i = 0; i < ARRAY_SIZE(apmixed_ex); i++) { + const struct mtk_apmixed_ex *ape = &apmixed_ex[i]; + + clk = mtk_clk_register_ref2usb_tx(ape->name, ape->parent, + base + ape->reg_ofs); + + if (IS_ERR(clk)) { + pr_err("Failed to register clk %s: %ld\n", ape->name, + PTR_ERR(clk)); + continue; + } + + clk_data->clks[CLK_APMIXED_REF2USB_TX] = clk; + } +} + #define MT8173_PLL_FMAX (3000UL * MHZ) #define CON0_MT8173_RST_BAR BIT(24) @@ -1010,12 +1146,19 @@ static const struct mtk_pll_data plls[] = { static void __init mtk_apmixedsys_init(struct device_node *node) { struct clk_onecell_data *clk_data; + int r; mt8173_pll_clk_data = clk_data = mtk_alloc_clk_data(CLK_APMIXED_NR_CLK); if (!clk_data) return; mtk_clk_register_plls(node, plls, ARRAY_SIZE(plls), clk_data); + mtk_clk_register_apmixedsys_special(node, clk_data); + + r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); + if (r) + pr_err("%s(): could not register clock provider: %d\n", + __func__, r); mtk_clk_enable_critical(); } diff --git a/drivers/clk/mediatek/clk-pll.c b/drivers/clk/mediatek/clk-pll.c index 44409e9..813f0c7 100644 --- a/drivers/clk/mediatek/clk-pll.c +++ b/drivers/clk/mediatek/clk-pll.c @@ -302,7 +302,7 @@ void __init mtk_clk_register_plls(struct device_node *node, const struct mtk_pll_data *plls, int num_plls, struct clk_onecell_data *clk_data) { void __iomem *base; - int r, i; + int i; struct clk *clk; base = of_iomap(node, 0); @@ -324,9 +324,4 @@ void __init mtk_clk_register_plls(struct device_node *node, clk_data->clks[pll->id] = clk; } - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); } diff --git a/include/dt-bindings/clock/mt8173-clk.h b/include/dt-bindings/clock/mt8173-clk.h index 6ce88bf..7b7c555 100644 --- a/include/dt-bindings/clock/mt8173-clk.h +++ b/include/dt-bindings/clock/mt8173-clk.h @@ -172,7 +172,8 @@ #define CLK_APMIXED_APLL2 12 #define CLK_APMIXED_LVDSPLL 13 #define CLK_APMIXED_MSDCPLL2 14 -#define CLK_APMIXED_NR_CLK 15 +#define CLK_APMIXED_REF2USB_TX 15 +#define CLK_APMIXED_NR_CLK 16 /* INFRA_SYS */
Add REF2USB_TX clock support into MT8173 APMIXEDSYS. This clock is needed by USB 3.0. Signed-off-by: James Liao <jamesjj.liao@mediatek.com> --- drivers/clk/mediatek/clk-mt8173.c | 143 +++++++++++++++++++++++++++++++++ drivers/clk/mediatek/clk-pll.c | 7 +- include/dt-bindings/clock/mt8173-clk.h | 3 +- 3 files changed, 146 insertions(+), 7 deletions(-)