@@ -127,6 +127,13 @@ to specify in a pin configuration subnode:
Definition: Selects the power source for the specified pins. Valid power
sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+- qcom,analog-level:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the source for analog output. Valued values are
+ defined in <dt-binding/pinctrl/qcom,pmic-mpp.h>
+ PMIC_MPP_AOUT_LVL_*
+
- qcom,analog-mode:
Usage: optional
Value type: <none>
@@ -61,6 +61,7 @@
#define PMIC_MPP_REG_DIG_PULL_CTL 0x42
#define PMIC_MPP_REG_DIG_IN_CTL 0x43
#define PMIC_MPP_REG_EN_CTL 0x46
+#define PMIC_MPP_REG_AOUT_CTL 0x48
#define PMIC_MPP_REG_AIN_CTL 0x4a
#define PMIC_MPP_REG_SINK_CTL 0x4c
@@ -100,6 +101,7 @@
#define PMIC_MPP_CONF_AMUX_ROUTE (PIN_CONFIG_END + 1)
#define PMIC_MPP_CONF_ANALOG_MODE (PIN_CONFIG_END + 2)
#define PMIC_MPP_CONF_SINK_MODE (PIN_CONFIG_END + 3)
+#define PMIC_MPP_CONF_ANALOG_LEVEL (PIN_CONFIG_END + 4)
/**
* struct pmic_mpp_pad - keep current MPP settings
@@ -115,6 +117,7 @@
* @num_sources: Number of power-sources supported by this MPP.
* @power_source: Current power-source used.
* @amux_input: Set the source for analog input.
+ * @aout_level: Analog output level
* @pullup: Pullup resistor value. Valid in Bidirectional mode only.
* @function: See pmic_mpp_functions[].
* @drive_strength: Amount of current in sink mode
@@ -131,6 +134,7 @@ struct pmic_mpp_pad {
unsigned int num_sources;
unsigned int power_source;
unsigned int amux_input;
+ unsigned int aout_level;
unsigned int pullup;
unsigned int function;
unsigned int drive_strength;
@@ -145,6 +149,7 @@ struct pmic_mpp_state {
static const struct pinconf_generic_params pmic_mpp_bindings[] = {
{"qcom,amux-route", PMIC_MPP_CONF_AMUX_ROUTE, 0},
+ {"qcom,analog-level", PMIC_MPP_CONF_ANALOG_LEVEL, 0},
{"qcom,analog-mode", PMIC_MPP_CONF_ANALOG_MODE, 0},
{"qcom,sink-mode", PMIC_MPP_CONF_SINK_MODE, 0},
};
@@ -152,6 +157,7 @@ static const struct pinconf_generic_params pmic_mpp_bindings[] = {
#ifdef CONFIG_DEBUG_FS
static const struct pin_config_item pmic_conf_items[] = {
PCONFDUMP(PMIC_MPP_CONF_AMUX_ROUTE, "analog mux", NULL, true),
+ PCONFDUMP(PMIC_MPP_CONF_ANALOG_LEVEL, "analog level", NULL, true),
PCONFDUMP(PMIC_MPP_CONF_ANALOG_MODE, "analog output", NULL, false),
PCONFDUMP(PMIC_MPP_CONF_SINK_MODE, "sink mode", NULL, false),
};
@@ -358,6 +364,9 @@ static int pmic_mpp_config_get(struct pinctrl_dev *pctldev,
case PIN_CONFIG_DRIVE_STRENGTH:
arg = pad->drive_strength;
break;
+ case PMIC_MPP_CONF_ANALOG_LEVEL:
+ arg = pad->aout_level;
+ break;
case PMIC_MPP_CONF_ANALOG_MODE:
arg = pad->analog_mode;
break;
@@ -433,6 +442,9 @@ static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
return -EINVAL;
pad->amux_input = arg;
break;
+ case PMIC_MPP_CONF_ANALOG_LEVEL:
+ pad->aout_level = arg;
+ break;
case PMIC_MPP_CONF_ANALOG_MODE:
pad->analog_mode = !!arg;
break;
@@ -462,6 +474,10 @@ static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
if (ret < 0)
return ret;
+ ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_AOUT_CTL, pad->aout_level);
+ if (ret < 0)
+ return ret;
+
ret = pmic_mpp_write_mode_ctl(state, pad);
if (ret < 0)
return ret;
@@ -507,6 +523,7 @@ static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev,
seq_printf(s, " %-7s", modes[pad->analog_mode ? 1 : (pad->sink_mode ? 2 : 0)]);
seq_printf(s, " %-7s", pmic_mpp_functions[pad->function]);
seq_printf(s, " vin-%d", pad->power_source);
+ seq_printf(s, " %d", pad->aout_level);
seq_printf(s, " %-8s", biases[pad->pullup]);
seq_printf(s, " %-4s", pad->out_value ? "high" : "low");
}
@@ -748,6 +765,10 @@ static int pmic_mpp_populate(struct pmic_mpp_state *state,
pad->drive_strength = val;
+ val = pmic_mpp_read(state, pad, PMIC_MPP_REG_AOUT_CTL);
+ if (val < 0)
+ return val;
+
val = pmic_mpp_read(state, pad, PMIC_MPP_REG_EN_CTL);
if (val < 0)
return val;
When the MPP is configured for analog output the output level is selected by the AOUT_CTL register, this patch makes it possible to control this. Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> --- .../devicetree/bindings/pinctrl/qcom,pmic-mpp.txt | 7 +++++++ drivers/pinctrl/qcom/pinctrl-spmi-mpp.c | 21 +++++++++++++++++++++ 2 files changed, 28 insertions(+)