| Message ID | 1449470374-31191-1-git-send-email-ykk@rock-chips.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Mon, Dec 07, 2015 at 02:39:34PM +0800, Yakir Yang wrote: > Rockchip DP driver is a helper driver of analogix_dp coder driver, > so most of the DT property should be descriped in analogix_dp document. > > Signed-off-by: Yakir Yang <ykk@rock-chips.com> > Reviewed-by: Heiko Stuebner <heiko@sntech.de> I already acked the previous v10 you sent. Acked-by: Rob Herring <robh@kernel.org> > --- > Changes in v10: None > Changes in v9: > - Document more details for 'ports' property. > > Changes in v8: > - Modify the commit subject name. (Heiko) > > Changes in v7: None > Changes in v6: None > Changes in v5: > - Split binding doc's from driver changes. (Rob) > - Add eDP hotplug pinctrl property. (Heiko) > > Changes in v4: None > Changes in v3: None > Changes in v2: None > > .../display/rockchip/analogix_dp-rockchip.txt | 91 ++++++++++++++++++++++ > 1 file changed, 91 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt > > diff --git a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt > new file mode 100644 > index 0000000..dae86c4 > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt > @@ -0,0 +1,91 @@ > +Rockchip RK3288 specific extensions to the Analogix Display Port > +================================ > + > +Required properties: > +- compatible: "rockchip,rk3288-edp"; > + > +- reg: physical base address of the controller and length > + > +- clocks: from common clock binding: handle to dp clock. > + of memory mapped region. > + > +- clock-names: from common clock binding: > + Required elements: "dp" "pclk" > + > +- resets: Must contain an entry for each entry in reset-names. > + See ../reset/reset.txt for details. > + > +- pinctrl-names: Names corresponding to the chip hotplug pinctrl states. > +- pinctrl-0: pin-control mode. should be <&edp_hpd> > + > +- reset-names: Must include the name "dp" > + > +- rockchip,grf: this soc should set GRF regs, so need get grf here. > + > +- ports: there are 2 port nodes with endpoint definitions as defined in > + Documentation/devicetree/bindings/media/video-interfaces.txt. > + Port 0: contained 2 endpoints, connecting to the ouput of vop. > + Port 1: contained 1 endpoint, connecting to the input of panel. > + > +For the below properties, please refer to Analogix DP binding document: > + * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt > +- phys (required) > +- phy-names (required) > +- hpd-gpios (optional) > +------------------------------------------------------------------------------- > + > +Example: > + dp-controller: dp@ff970000 { > + compatible = "rockchip,rk3288-dp"; > + reg = <0xff970000 0x4000>; > + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cru SCLK_EDP>, <&cru PCLK_EDP_CTRL>; > + clock-names = "dp", "pclk"; > + phys = <&dp_phy>; > + phy-names = "dp"; > + > + rockchip,grf = <&grf>; > + resets = <&cru 111>; > + reset-names = "dp"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&edp_hpd>; > + > + status = "disabled"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + edp_in: port@0 { > + reg = <0>; > + #address-cells = <1>; > + #size-cells = <0>; > + edp_in_vopb: endpoint@0 { > + reg = <0>; > + remote-endpoint = <&vopb_out_edp>; > + }; > + edp_in_vopl: endpoint@1 { > + reg = <1>; > + remote-endpoint = <&vopl_out_edp>; > + }; > + }; > + > + edp_out: port@1 { > + reg = <1>; > + #address-cells = <1>; > + #size-cells = <0>; > + edp_out_panel: endpoint { > + reg = <0>; > + remote-endpoint = <&panel_in_edp> > + }; > + }; > + }; > + }; > + > + pinctrl { > + edp { > + edp_hpd: edp-hpd { > + rockchip,pins = <7 11 RK_FUNC_2 &pcfg_pull_none>; > + }; > + }; > + }; > -- > 1.9.1 > > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Rob, On 12/08/2015 11:03 PM, Rob Herring wrote: > On Mon, Dec 07, 2015 at 02:39:34PM +0800, Yakir Yang wrote: >> Rockchip DP driver is a helper driver of analogix_dp coder driver, >> so most of the DT property should be descriped in analogix_dp document. >> >> Signed-off-by: Yakir Yang <ykk@rock-chips.com> >> Reviewed-by: Heiko Stuebner <heiko@sntech.de> > I already acked the previous v10 you sent. > > Acked-by: Rob Herring <robh@kernel.org> Ah, I remember it, sorry about the mistaken :-D Thanks - Yakir > >> --- >> Changes in v10: None >> Changes in v9: >> - Document more details for 'ports' property. >> >> Changes in v8: >> - Modify the commit subject name. (Heiko) >> >> Changes in v7: None >> Changes in v6: None >> Changes in v5: >> - Split binding doc's from driver changes. (Rob) >> - Add eDP hotplug pinctrl property. (Heiko) >> >> Changes in v4: None >> Changes in v3: None >> Changes in v2: None >> >> .../display/rockchip/analogix_dp-rockchip.txt | 91 ++++++++++++++++++++++ >> 1 file changed, 91 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt >> >> diff --git a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt >> new file mode 100644 >> index 0000000..dae86c4 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt >> @@ -0,0 +1,91 @@ >> +Rockchip RK3288 specific extensions to the Analogix Display Port >> +================================ >> + >> +Required properties: >> +- compatible: "rockchip,rk3288-edp"; >> + >> +- reg: physical base address of the controller and length >> + >> +- clocks: from common clock binding: handle to dp clock. >> + of memory mapped region. >> + >> +- clock-names: from common clock binding: >> + Required elements: "dp" "pclk" >> + >> +- resets: Must contain an entry for each entry in reset-names. >> + See ../reset/reset.txt for details. >> + >> +- pinctrl-names: Names corresponding to the chip hotplug pinctrl states. >> +- pinctrl-0: pin-control mode. should be <&edp_hpd> >> + >> +- reset-names: Must include the name "dp" >> + >> +- rockchip,grf: this soc should set GRF regs, so need get grf here. >> + >> +- ports: there are 2 port nodes with endpoint definitions as defined in >> + Documentation/devicetree/bindings/media/video-interfaces.txt. >> + Port 0: contained 2 endpoints, connecting to the ouput of vop. >> + Port 1: contained 1 endpoint, connecting to the input of panel. >> + >> +For the below properties, please refer to Analogix DP binding document: >> + * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt >> +- phys (required) >> +- phy-names (required) >> +- hpd-gpios (optional) >> +------------------------------------------------------------------------------- >> + >> +Example: >> + dp-controller: dp@ff970000 { >> + compatible = "rockchip,rk3288-dp"; >> + reg = <0xff970000 0x4000>; >> + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&cru SCLK_EDP>, <&cru PCLK_EDP_CTRL>; >> + clock-names = "dp", "pclk"; >> + phys = <&dp_phy>; >> + phy-names = "dp"; >> + >> + rockchip,grf = <&grf>; >> + resets = <&cru 111>; >> + reset-names = "dp"; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&edp_hpd>; >> + >> + status = "disabled"; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + edp_in: port@0 { >> + reg = <0>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + edp_in_vopb: endpoint@0 { >> + reg = <0>; >> + remote-endpoint = <&vopb_out_edp>; >> + }; >> + edp_in_vopl: endpoint@1 { >> + reg = <1>; >> + remote-endpoint = <&vopl_out_edp>; >> + }; >> + }; >> + >> + edp_out: port@1 { >> + reg = <1>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + edp_out_panel: endpoint { >> + reg = <0>; >> + remote-endpoint = <&panel_in_edp> >> + }; >> + }; >> + }; >> + }; >> + >> + pinctrl { >> + edp { >> + edp_hpd: edp-hpd { >> + rockchip,pins = <7 11 RK_FUNC_2 &pcfg_pull_none>; >> + }; >> + }; >> + }; >> -- >> 1.9.1 >> >> > > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt new file mode 100644 index 0000000..dae86c4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt @@ -0,0 +1,91 @@ +Rockchip RK3288 specific extensions to the Analogix Display Port +================================ + +Required properties: +- compatible: "rockchip,rk3288-edp"; + +- reg: physical base address of the controller and length + +- clocks: from common clock binding: handle to dp clock. + of memory mapped region. + +- clock-names: from common clock binding: + Required elements: "dp" "pclk" + +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + +- pinctrl-names: Names corresponding to the chip hotplug pinctrl states. +- pinctrl-0: pin-control mode. should be <&edp_hpd> + +- reset-names: Must include the name "dp" + +- rockchip,grf: this soc should set GRF regs, so need get grf here. + +- ports: there are 2 port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Port 0: contained 2 endpoints, connecting to the ouput of vop. + Port 1: contained 1 endpoint, connecting to the input of panel. + +For the below properties, please refer to Analogix DP binding document: + * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt +- phys (required) +- phy-names (required) +- hpd-gpios (optional) +------------------------------------------------------------------------------- + +Example: + dp-controller: dp@ff970000 { + compatible = "rockchip,rk3288-dp"; + reg = <0xff970000 0x4000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_EDP>, <&cru PCLK_EDP_CTRL>; + clock-names = "dp", "pclk"; + phys = <&dp_phy>; + phy-names = "dp"; + + rockchip,grf = <&grf>; + resets = <&cru 111>; + reset-names = "dp"; + + pinctrl-names = "default"; + pinctrl-0 = <&edp_hpd>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + edp_in: port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + edp_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_edp>; + }; + edp_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_edp>; + }; + }; + + edp_out: port@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + edp_out_panel: endpoint { + reg = <0>; + remote-endpoint = <&panel_in_edp> + }; + }; + }; + }; + + pinctrl { + edp { + edp_hpd: edp-hpd { + rockchip,pins = <7 11 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + };