@@ -49,12 +49,6 @@ int focaltech_detect(struct psmouse *psmouse, bool set_properties)
return 0;
}
-static void focaltech_reset(struct psmouse *psmouse)
-{
- ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
- psmouse_reset(psmouse);
-}
-
#ifdef CONFIG_MOUSE_PS2_FOCALTECH
/*
@@ -300,6 +294,12 @@ static int focaltech_switch_protocol(struct psmouse *psmouse)
return 0;
}
+static void focaltech_reset(struct psmouse *psmouse)
+{
+ ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
+ psmouse_reset(psmouse);
+}
+
static void focaltech_disconnect(struct psmouse *psmouse)
{
focaltech_reset(psmouse);
@@ -456,14 +456,4 @@ fail:
kfree(priv);
return error;
}
-
-#else /* CONFIG_MOUSE_PS2_FOCALTECH */
-
-int focaltech_init(struct psmouse *psmouse)
-{
- focaltech_reset(psmouse);
-
- return 0;
-}
-
#endif /* CONFIG_MOUSE_PS2_FOCALTECH */
@@ -18,6 +18,14 @@
#define _FOCALTECH_H
int focaltech_detect(struct psmouse *psmouse, bool set_properties);
+
+#ifdef CONFIG_MOUSE_PS2_FOCALTECH
int focaltech_init(struct psmouse *psmouse);
+#else
+static inline int focaltech_init(struct psmouse *psmouse)
+{
+ return -ENOSYS;
+}
+#endif
#endif
@@ -750,19 +750,20 @@ static int psmouse_extensions(struct psmouse *psmouse,
*/
if (psmouse_do_detect(focaltech_detect, psmouse, set_properties) == 0) {
if (max_proto > PSMOUSE_IMEX) {
- if (!set_properties || focaltech_init(psmouse) == 0) {
- if (IS_ENABLED(CONFIG_MOUSE_PS2_FOCALTECH))
- return PSMOUSE_FOCALTECH;
- /*
- * Note that we need to also restrict
- * psmouse_max_proto so that psmouse_initialize()
- * does not try to reset rate and resolution,
- * because even that upsets the device.
- */
- psmouse_max_proto = PSMOUSE_PS2;
- return PSMOUSE_PS2;
+ if (IS_ENABLED(CONFIG_MOUSE_PS2_FOCALTECH) &&
+ (!set_properties || focaltech_init(psmouse) == 0)) {
+ return PSMOUSE_FOCALTECH;
}
}
+ /*
+ * Restrict psmouse_max_proto so that psmouse_initialize()
+ * does not try to reset rate and resolution, because even
+ * that upsets the device.
+ * This also causes us to basically fall through to basic
+ * protocol detection, where we fully reset the mouse,
+ * and set it up as bare PS/2 protocol device.
+ */
+ psmouse_max_proto = max_proto = PSMOUSE_PS2;
}
/*
The fact that we were calling focaltech_init() even when Focaltech support is disabled was confusing. Rearrange the code so that if support is disabled we continue to fall through the rest of protocol probing code until we get to full reset that Focaltech devices need to work properly. Also, replace focaltech_init() with a stub now that it is only called when protocol is enabled. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> --- I know I originally requested doing reset in focaltech_init() even when focaltech support is disabled, but as I was working with the code I found it confusing. drivers/input/mouse/focaltech.c | 22 ++++++---------------- drivers/input/mouse/focaltech.h | 8 ++++++++ drivers/input/mouse/psmouse-base.c | 23 ++++++++++++----------- 3 files changed, 26 insertions(+), 27 deletions(-)