Message ID | 1450709399-7246-4-git-send-email-aleksey.makarov@linaro.org (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On Mon, Dec 21, 2015 at 4:49 PM, Aleksey Makarov <aleksey.makarov@linaro.org> wrote: > From: Graeme Gregory <graeme.gregory@linaro.org> > > In ACPI this device is only defined in SBSA mode so > if we are coming from ACPI use this mode. > > Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org> > Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org> > --- > drivers/tty/serial/amba-pl011.c | 37 ++++++++++++++++++++++++++----------- > 1 file changed, 26 insertions(+), 11 deletions(-) > > diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c > index 899a771..766ce4f 100644 > --- a/drivers/tty/serial/amba-pl011.c > +++ b/drivers/tty/serial/amba-pl011.c > @@ -2368,18 +2368,33 @@ static int pl011_probe(struct amba_device *dev, const struct amba_id *id) > if (!uap) > return -ENOMEM; > > - uap->clk = devm_clk_get(&dev->dev, NULL); > - if (IS_ERR(uap->clk)) > - return PTR_ERR(uap->clk); > - > - uap->vendor = vendor; > - uap->lcrh_rx = vendor->lcrh_rx; > - uap->lcrh_tx = vendor->lcrh_tx; > - uap->fifosize = vendor->get_fifosize(dev); > - uap->port.irq = dev->irq[0]; > - uap->port.ops = &amba_pl011_pops; > + /* ACPI only defines SBSA variant */ > + if (ACPI_COMPANION(&dev->dev)) { has_acpi_companion() > + /* > + * According to ARM ARMH0011 is currently the only mapping > + * of pl011 in ACPI and it's mapped to SBSA UART mode > + */ > + uap->vendor = &vendor_sbsa; > + uap->fifosize = 32; > + uap->port.ops = &sbsa_uart_pops; > + uap->fixed_baud = 115200; Shouldn't you match by ID and provide the custom values if any? On the other hand have you checked if it's possible to use _DSD in this case? > > - snprintf(uap->type, sizeof(uap->type), "PL011 rev%u", amba_rev(dev)); > + snprintf(uap->type, sizeof(uap->type), "SBSA"); > + } else { > + uap->clk = devm_clk_get(&dev->dev, NULL); > + if (IS_ERR(uap->clk)) > + return PTR_ERR(uap->clk); > + > + uap->vendor = vendor; > + uap->lcrh_rx = vendor->lcrh_rx; > + uap->lcrh_tx = vendor->lcrh_tx; > + uap->fifosize = vendor->get_fifosize(dev); > + uap->port.ops = &amba_pl011_pops; > + > + snprintf(uap->type, sizeof(uap->type), "PL011 rev%u", > + amba_rev(dev)); > + } > + uap->port.irq = dev->irq[0]; > > ret = pl011_setup_port(&dev->dev, uap, &dev->res, portnr); > if (ret) > -- > 2.6.4 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/
On 21 December 2015 at 18:11, Andy Shevchenko <andy.shevchenko@gmail.com> wrote: > On Mon, Dec 21, 2015 at 4:49 PM, Aleksey Makarov > <aleksey.makarov@linaro.org> wrote: >> From: Graeme Gregory <graeme.gregory@linaro.org> >> >> In ACPI this device is only defined in SBSA mode so >> if we are coming from ACPI use this mode. >> >> Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org> >> Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org> >> --- >> drivers/tty/serial/amba-pl011.c | 37 ++++++++++++++++++++++++++----------- >> 1 file changed, 26 insertions(+), 11 deletions(-) >> >> diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c >> index 899a771..766ce4f 100644 >> --- a/drivers/tty/serial/amba-pl011.c >> +++ b/drivers/tty/serial/amba-pl011.c >> @@ -2368,18 +2368,33 @@ static int pl011_probe(struct amba_device *dev, const struct amba_id *id) >> if (!uap) >> return -ENOMEM; >> >> - uap->clk = devm_clk_get(&dev->dev, NULL); >> - if (IS_ERR(uap->clk)) >> - return PTR_ERR(uap->clk); >> - >> - uap->vendor = vendor; >> - uap->lcrh_rx = vendor->lcrh_rx; >> - uap->lcrh_tx = vendor->lcrh_tx; >> - uap->fifosize = vendor->get_fifosize(dev); >> - uap->port.irq = dev->irq[0]; >> - uap->port.ops = &amba_pl011_pops; >> + /* ACPI only defines SBSA variant */ >> + if (ACPI_COMPANION(&dev->dev)) { > > has_acpi_companion() > >> + /* >> + * According to ARM ARMH0011 is currently the only mapping >> + * of pl011 in ACPI and it's mapped to SBSA UART mode >> + */ >> + uap->vendor = &vendor_sbsa; >> + uap->fifosize = 32; >> + uap->port.ops = &sbsa_uart_pops; >> + uap->fixed_baud = 115200; > > Shouldn't you match by ID and provide the custom values if any? > On the other hand have you checked if it's possible to use _DSD in this case? > So far I have not seen any use of SBSA UART other than this in real life. I am a little opposed to providing complexity people are not going to use. Graeme
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index 899a771..766ce4f 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -2368,18 +2368,33 @@ static int pl011_probe(struct amba_device *dev, const struct amba_id *id) if (!uap) return -ENOMEM; - uap->clk = devm_clk_get(&dev->dev, NULL); - if (IS_ERR(uap->clk)) - return PTR_ERR(uap->clk); - - uap->vendor = vendor; - uap->lcrh_rx = vendor->lcrh_rx; - uap->lcrh_tx = vendor->lcrh_tx; - uap->fifosize = vendor->get_fifosize(dev); - uap->port.irq = dev->irq[0]; - uap->port.ops = &amba_pl011_pops; + /* ACPI only defines SBSA variant */ + if (ACPI_COMPANION(&dev->dev)) { + /* + * According to ARM ARMH0011 is currently the only mapping + * of pl011 in ACPI and it's mapped to SBSA UART mode + */ + uap->vendor = &vendor_sbsa; + uap->fifosize = 32; + uap->port.ops = &sbsa_uart_pops; + uap->fixed_baud = 115200; - snprintf(uap->type, sizeof(uap->type), "PL011 rev%u", amba_rev(dev)); + snprintf(uap->type, sizeof(uap->type), "SBSA"); + } else { + uap->clk = devm_clk_get(&dev->dev, NULL); + if (IS_ERR(uap->clk)) + return PTR_ERR(uap->clk); + + uap->vendor = vendor; + uap->lcrh_rx = vendor->lcrh_rx; + uap->lcrh_tx = vendor->lcrh_tx; + uap->fifosize = vendor->get_fifosize(dev); + uap->port.ops = &amba_pl011_pops; + + snprintf(uap->type, sizeof(uap->type), "PL011 rev%u", + amba_rev(dev)); + } + uap->port.irq = dev->irq[0]; ret = pl011_setup_port(&dev->dev, uap, &dev->res, portnr); if (ret)