| Message ID | 1448358147-23663-3-git-send-email-linux@rasmusvillemoes.dk (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
On 15-11-24 04:42 AM, Rasmus Villemoes wrote: > This is a purely mechanical move of the list of additional sense codes > to a separate file, in preparation for reducing the impact of choosing > CONFIG_SCSI_CONSTANTS=y by about 8k. > > Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Tested-by: Douglas Gilbert <dgilbert@interlog.com> > --- > drivers/scsi/constants.c | 830 +-------------------------------------------- > drivers/scsi/sense_codes.h | 826 ++++++++++++++++++++++++++++++++++++++++++++ > 2 files changed, 829 insertions(+), 827 deletions(-) > create mode 100644 drivers/scsi/sense_codes.h > > diff --git a/drivers/scsi/constants.c b/drivers/scsi/constants.c > index 58d94e3c3713..6e813eec4f8d 100644 > --- a/drivers/scsi/constants.c > +++ b/drivers/scsi/constants.c > @@ -295,835 +295,11 @@ struct error_info { > const char * text; > }; > > -/* > - * The canonical list of T10 Additional Sense Codes is available at: > - * http://www.t10.org/lists/asc-num.txt [most recent: 20141221] > - */ > - > static const struct error_info additional[] = > { > - {0x0000, "No additional sense information"}, > - {0x0001, "Filemark detected"}, > - {0x0002, "End-of-partition/medium detected"}, > - {0x0003, "Setmark detected"}, > - {0x0004, "Beginning-of-partition/medium detected"}, > - {0x0005, "End-of-data detected"}, > - {0x0006, "I/O process terminated"}, > - {0x0007, "Programmable early warning detected"}, > - {0x0011, "Audio play operation in progress"}, > - {0x0012, "Audio play operation paused"}, > - {0x0013, "Audio play operation successfully completed"}, > - {0x0014, "Audio play operation stopped due to error"}, > - {0x0015, "No current audio status to return"}, > - {0x0016, "Operation in progress"}, > - {0x0017, "Cleaning requested"}, > - {0x0018, "Erase operation in progress"}, > - {0x0019, "Locate operation in progress"}, > - {0x001A, "Rewind operation in progress"}, > - {0x001B, "Set capacity operation in progress"}, > - {0x001C, "Verify operation in progress"}, > - {0x001D, "ATA pass through information available"}, > - {0x001E, "Conflicting SA creation request"}, > - {0x001F, "Logical unit transitioning to another power condition"}, > - {0x0020, "Extended copy information available"}, > - {0x0021, "Atomic command aborted due to ACA"}, > - > - {0x0100, "No index/sector signal"}, > - > - {0x0200, "No seek complete"}, > - > - {0x0300, "Peripheral device write fault"}, > - {0x0301, "No write current"}, > - {0x0302, "Excessive write errors"}, > - > - {0x0400, "Logical unit not ready, cause not reportable"}, > - {0x0401, "Logical unit is in process of becoming ready"}, > - {0x0402, "Logical unit not ready, initializing command required"}, > - {0x0403, "Logical unit not ready, manual intervention required"}, > - {0x0404, "Logical unit not ready, format in progress"}, > - {0x0405, "Logical unit not ready, rebuild in progress"}, > - {0x0406, "Logical unit not ready, recalculation in progress"}, > - {0x0407, "Logical unit not ready, operation in progress"}, > - {0x0408, "Logical unit not ready, long write in progress"}, > - {0x0409, "Logical unit not ready, self-test in progress"}, > - {0x040A, "Logical unit not accessible, asymmetric access state transition"}, > - {0x040B, "Logical unit not accessible, target port in standby state"}, > - {0x040C, "Logical unit not accessible, target port in unavailable state"}, > - {0x040D, "Logical unit not ready, structure check required"}, > - {0x040E, "Logical unit not ready, security session in progress"}, > - {0x0410, "Logical unit not ready, auxiliary memory not accessible"}, > - {0x0411, "Logical unit not ready, notify (enable spinup) required"}, > - {0x0412, "Logical unit not ready, offline"}, > - {0x0413, "Logical unit not ready, SA creation in progress"}, > - {0x0414, "Logical unit not ready, space allocation in progress"}, > - {0x0415, "Logical unit not ready, robotics disabled"}, > - {0x0416, "Logical unit not ready, configuration required"}, > - {0x0417, "Logical unit not ready, calibration required"}, > - {0x0418, "Logical unit not ready, a door is open"}, > - {0x0419, "Logical unit not ready, operating in sequential mode"}, > - {0x041A, "Logical unit not ready, start stop unit command in progress"}, > - {0x041B, "Logical unit not ready, sanitize in progress"}, > - {0x041C, "Logical unit not ready, additional power use not yet granted"}, > - {0x041D, "Logical unit not ready, configuration in progress"}, > - {0x041E, "Logical unit not ready, microcode activation required"}, > - {0x041F, "Logical unit not ready, microcode download required"}, > - {0x0420, "Logical unit not ready, logical unit reset required"}, > - {0x0421, "Logical unit not ready, hard reset required"}, > - {0x0422, "Logical unit not ready, power cycle required"}, > - > - {0x0500, "Logical unit does not respond to selection"}, > - > - {0x0600, "No reference position found"}, > - > - {0x0700, "Multiple peripheral devices selected"}, > - > - {0x0800, "Logical unit communication failure"}, > - {0x0801, "Logical unit communication time-out"}, > - {0x0802, "Logical unit communication parity error"}, > - {0x0803, "Logical unit communication CRC error (Ultra-DMA/32)"}, > - {0x0804, "Unreachable copy target"}, > - > - {0x0900, "Track following error"}, > - {0x0901, "Tracking servo failure"}, > - {0x0902, "Focus servo failure"}, > - {0x0903, "Spindle servo failure"}, > - {0x0904, "Head select fault"}, > - {0x0905, "Vibration induced tracking error"}, > - > - {0x0A00, "Error log overflow"}, > - > - {0x0B00, "Warning"}, > - {0x0B01, "Warning - specified temperature exceeded"}, > - {0x0B02, "Warning - enclosure degraded"}, > - {0x0B03, "Warning - background self-test failed"}, > - {0x0B04, "Warning - background pre-scan detected medium error"}, > - {0x0B05, "Warning - background medium scan detected medium error"}, > - {0x0B06, "Warning - non-volatile cache now volatile"}, > - {0x0B07, "Warning - degraded power to non-volatile cache"}, > - {0x0B08, "Warning - power loss expected"}, > - {0x0B09, "Warning - device statistics notification active"}, > - > - {0x0C00, "Write error"}, > - {0x0C01, "Write error - recovered with auto reallocation"}, > - {0x0C02, "Write error - auto reallocation failed"}, > - {0x0C03, "Write error - recommend reassignment"}, > - {0x0C04, "Compression check miscompare error"}, > - {0x0C05, "Data expansion occurred during compression"}, > - {0x0C06, "Block not compressible"}, > - {0x0C07, "Write error - recovery needed"}, > - {0x0C08, "Write error - recovery failed"}, > - {0x0C09, "Write error - loss of streaming"}, > - {0x0C0A, "Write error - padding blocks added"}, > - {0x0C0B, "Auxiliary memory write error"}, > - {0x0C0C, "Write error - unexpected unsolicited data"}, > - {0x0C0D, "Write error - not enough unsolicited data"}, > - {0x0C0E, "Multiple write errors"}, > - {0x0C0F, "Defects in error window"}, > - {0x0C10, "Incomplete multiple atomic write operations"}, > - > - {0x0D00, "Error detected by third party temporary initiator"}, > - {0x0D01, "Third party device failure"}, > - {0x0D02, "Copy target device not reachable"}, > - {0x0D03, "Incorrect copy target device type"}, > - {0x0D04, "Copy target device data underrun"}, > - {0x0D05, "Copy target device data overrun"}, > - > - {0x0E00, "Invalid information unit"}, > - {0x0E01, "Information unit too short"}, > - {0x0E02, "Information unit too long"}, > - {0x0E03, "Invalid field in command information unit"}, > - > - {0x1000, "Id CRC or ECC error"}, > - {0x1001, "Logical block guard check failed"}, > - {0x1002, "Logical block application tag check failed"}, > - {0x1003, "Logical block reference tag check failed"}, > - {0x1004, "Logical block protection error on recover buffered data"}, > - {0x1005, "Logical block protection method error"}, > - > - {0x1100, "Unrecovered read error"}, > - {0x1101, "Read retries exhausted"}, > - {0x1102, "Error too long to correct"}, > - {0x1103, "Multiple read errors"}, > - {0x1104, "Unrecovered read error - auto reallocate failed"}, > - {0x1105, "L-EC uncorrectable error"}, > - {0x1106, "CIRC unrecovered error"}, > - {0x1107, "Data re-synchronization error"}, > - {0x1108, "Incomplete block read"}, > - {0x1109, "No gap found"}, > - {0x110A, "Miscorrected error"}, > - {0x110B, "Unrecovered read error - recommend reassignment"}, > - {0x110C, "Unrecovered read error - recommend rewrite the data"}, > - {0x110D, "De-compression CRC error"}, > - {0x110E, "Cannot decompress using declared algorithm"}, > - {0x110F, "Error reading UPC/EAN number"}, > - {0x1110, "Error reading ISRC number"}, > - {0x1111, "Read error - loss of streaming"}, > - {0x1112, "Auxiliary memory read error"}, > - {0x1113, "Read error - failed retransmission request"}, > - {0x1114, "Read error - lba marked bad by application client"}, > - {0x1115, "Write after sanitize required"}, > - > - {0x1200, "Address mark not found for id field"}, > - > - {0x1300, "Address mark not found for data field"}, > - > - {0x1400, "Recorded entity not found"}, > - {0x1401, "Record not found"}, > - {0x1402, "Filemark or setmark not found"}, > - {0x1403, "End-of-data not found"}, > - {0x1404, "Block sequence error"}, > - {0x1405, "Record not found - recommend reassignment"}, > - {0x1406, "Record not found - data auto-reallocated"}, > - {0x1407, "Locate operation failure"}, > - > - {0x1500, "Random positioning error"}, > - {0x1501, "Mechanical positioning error"}, > - {0x1502, "Positioning error detected by read of medium"}, > - > - {0x1600, "Data synchronization mark error"}, > - {0x1601, "Data sync error - data rewritten"}, > - {0x1602, "Data sync error - recommend rewrite"}, > - {0x1603, "Data sync error - data auto-reallocated"}, > - {0x1604, "Data sync error - recommend reassignment"}, > - > - {0x1700, "Recovered data with no error correction applied"}, > - {0x1701, "Recovered data with retries"}, > - {0x1702, "Recovered data with positive head offset"}, > - {0x1703, "Recovered data with negative head offset"}, > - {0x1704, "Recovered data with retries and/or circ applied"}, > - {0x1705, "Recovered data using previous sector id"}, > - {0x1706, "Recovered data without ECC - data auto-reallocated"}, > - {0x1707, "Recovered data without ECC - recommend reassignment"}, > - {0x1708, "Recovered data without ECC - recommend rewrite"}, > - {0x1709, "Recovered data without ECC - data rewritten"}, > - > - {0x1800, "Recovered data with error correction applied"}, > - {0x1801, "Recovered data with error corr. & retries applied"}, > - {0x1802, "Recovered data - data auto-reallocated"}, > - {0x1803, "Recovered data with CIRC"}, > - {0x1804, "Recovered data with L-EC"}, > - {0x1805, "Recovered data - recommend reassignment"}, > - {0x1806, "Recovered data - recommend rewrite"}, > - {0x1807, "Recovered data with ECC - data rewritten"}, > - {0x1808, "Recovered data with linking"}, > - > - {0x1900, "Defect list error"}, > - {0x1901, "Defect list not available"}, > - {0x1902, "Defect list error in primary list"}, > - {0x1903, "Defect list error in grown list"}, > - > - {0x1A00, "Parameter list length error"}, > - > - {0x1B00, "Synchronous data transfer error"}, > - > - {0x1C00, "Defect list not found"}, > - {0x1C01, "Primary defect list not found"}, > - {0x1C02, "Grown defect list not found"}, > - > - {0x1D00, "Miscompare during verify operation"}, > - {0x1D01, "Miscompare verify of unmapped LBA"}, > - > - {0x1E00, "Recovered id with ECC correction"}, > - > - {0x1F00, "Partial defect list transfer"}, > - > - {0x2000, "Invalid command operation code"}, > - {0x2001, "Access denied - initiator pending-enrolled"}, > - {0x2002, "Access denied - no access rights"}, > - {0x2003, "Access denied - invalid mgmt id key"}, > - {0x2004, "Illegal command while in write capable state"}, > - {0x2005, "Obsolete"}, > - {0x2006, "Illegal command while in explicit address mode"}, > - {0x2007, "Illegal command while in implicit address mode"}, > - {0x2008, "Access denied - enrollment conflict"}, > - {0x2009, "Access denied - invalid LU identifier"}, > - {0x200A, "Access denied - invalid proxy token"}, > - {0x200B, "Access denied - ACL LUN conflict"}, > - {0x200C, "Illegal command when not in append-only mode"}, > - > - {0x2100, "Logical block address out of range"}, > - {0x2101, "Invalid element address"}, > - {0x2102, "Invalid address for write"}, > - {0x2103, "Invalid write crossing layer jump"}, > - {0x2104, "Unaligned write command"}, > - {0x2105, "Write boundary violation"}, > - {0x2106, "Attempt to read invalid data"}, > - {0x2107, "Read boundary violation"}, > - > - {0x2200, "Illegal function (use 20 00, 24 00, or 26 00)"}, > - > - {0x2300, "Invalid token operation, cause not reportable"}, > - {0x2301, "Invalid token operation, unsupported token type"}, > - {0x2302, "Invalid token operation, remote token usage not supported"}, > - {0x2303, "Invalid token operation, remote rod token creation not supported"}, > - {0x2304, "Invalid token operation, token unknown"}, > - {0x2305, "Invalid token operation, token corrupt"}, > - {0x2306, "Invalid token operation, token revoked"}, > - {0x2307, "Invalid token operation, token expired"}, > - {0x2308, "Invalid token operation, token cancelled"}, > - {0x2309, "Invalid token operation, token deleted"}, > - {0x230A, "Invalid token operation, invalid token length"}, > - > - {0x2400, "Invalid field in cdb"}, > - {0x2401, "CDB decryption error"}, > - {0x2402, "Obsolete"}, > - {0x2403, "Obsolete"}, > - {0x2404, "Security audit value frozen"}, > - {0x2405, "Security working key frozen"}, > - {0x2406, "Nonce not unique"}, > - {0x2407, "Nonce timestamp out of range"}, > - {0x2408, "Invalid XCDB"}, > - > - {0x2500, "Logical unit not supported"}, > - > - {0x2600, "Invalid field in parameter list"}, > - {0x2601, "Parameter not supported"}, > - {0x2602, "Parameter value invalid"}, > - {0x2603, "Threshold parameters not supported"}, > - {0x2604, "Invalid release of persistent reservation"}, > - {0x2605, "Data decryption error"}, > - {0x2606, "Too many target descriptors"}, > - {0x2607, "Unsupported target descriptor type code"}, > - {0x2608, "Too many segment descriptors"}, > - {0x2609, "Unsupported segment descriptor type code"}, > - {0x260A, "Unexpected inexact segment"}, > - {0x260B, "Inline data length exceeded"}, > - {0x260C, "Invalid operation for copy source or destination"}, > - {0x260D, "Copy segment granularity violation"}, > - {0x260E, "Invalid parameter while port is enabled"}, > - {0x260F, "Invalid data-out buffer integrity check value"}, > - {0x2610, "Data decryption key fail limit reached"}, > - {0x2611, "Incomplete key-associated data set"}, > - {0x2612, "Vendor specific key reference not found"}, > - > - {0x2700, "Write protected"}, > - {0x2701, "Hardware write protected"}, > - {0x2702, "Logical unit software write protected"}, > - {0x2703, "Associated write protect"}, > - {0x2704, "Persistent write protect"}, > - {0x2705, "Permanent write protect"}, > - {0x2706, "Conditional write protect"}, > - {0x2707, "Space allocation failed write protect"}, > - {0x2708, "Zone is read only"}, > - > - {0x2800, "Not ready to ready change, medium may have changed"}, > - {0x2801, "Import or export element accessed"}, > - {0x2802, "Format-layer may have changed"}, > - {0x2803, "Import/export element accessed, medium changed"}, > - > - {0x2900, "Power on, reset, or bus device reset occurred"}, > - {0x2901, "Power on occurred"}, > - {0x2902, "Scsi bus reset occurred"}, > - {0x2903, "Bus device reset function occurred"}, > - {0x2904, "Device internal reset"}, > - {0x2905, "Transceiver mode changed to single-ended"}, > - {0x2906, "Transceiver mode changed to lvd"}, > - {0x2907, "I_T nexus loss occurred"}, > - > - {0x2A00, "Parameters changed"}, > - {0x2A01, "Mode parameters changed"}, > - {0x2A02, "Log parameters changed"}, > - {0x2A03, "Reservations preempted"}, > - {0x2A04, "Reservations released"}, > - {0x2A05, "Registrations preempted"}, > - {0x2A06, "Asymmetric access state changed"}, > - {0x2A07, "Implicit asymmetric access state transition failed"}, > - {0x2A08, "Priority changed"}, > - {0x2A09, "Capacity data has changed"}, > - {0x2A0A, "Error history I_T nexus cleared"}, > - {0x2A0B, "Error history snapshot released"}, > - {0x2A0C, "Error recovery attributes have changed"}, > - {0x2A0D, "Data encryption capabilities changed"}, > - {0x2A10, "Timestamp changed"}, > - {0x2A11, "Data encryption parameters changed by another i_t nexus"}, > - {0x2A12, "Data encryption parameters changed by vendor specific event"}, > - {0x2A13, "Data encryption key instance counter has changed"}, > - {0x2A14, "SA creation capabilities data has changed"}, > - {0x2A15, "Medium removal prevention preempted"}, > - > - {0x2B00, "Copy cannot execute since host cannot disconnect"}, > - > - {0x2C00, "Command sequence error"}, > - {0x2C01, "Too many windows specified"}, > - {0x2C02, "Invalid combination of windows specified"}, > - {0x2C03, "Current program area is not empty"}, > - {0x2C04, "Current program area is empty"}, > - {0x2C05, "Illegal power condition request"}, > - {0x2C06, "Persistent prevent conflict"}, > - {0x2C07, "Previous busy status"}, > - {0x2C08, "Previous task set full status"}, > - {0x2C09, "Previous reservation conflict status"}, > - {0x2C0A, "Partition or collection contains user objects"}, > - {0x2C0B, "Not reserved"}, > - {0x2C0C, "Orwrite generation does not match"}, > - {0x2C0D, "Reset write pointer not allowed"}, > - {0x2C0E, "Zone is offline"}, > - > - {0x2D00, "Overwrite error on update in place"}, > - > - {0x2E00, "Insufficient time for operation"}, > - {0x2E01, "Command timeout before processing"}, > - {0x2E02, "Command timeout during processing"}, > - {0x2E03, "Command timeout during processing due to error recovery"}, > - > - {0x2F00, "Commands cleared by another initiator"}, > - {0x2F01, "Commands cleared by power loss notification"}, > - {0x2F02, "Commands cleared by device server"}, > - {0x2F03, "Some commands cleared by queuing layer event"}, > - > - {0x3000, "Incompatible medium installed"}, > - {0x3001, "Cannot read medium - unknown format"}, > - {0x3002, "Cannot read medium - incompatible format"}, > - {0x3003, "Cleaning cartridge installed"}, > - {0x3004, "Cannot write medium - unknown format"}, > - {0x3005, "Cannot write medium - incompatible format"}, > - {0x3006, "Cannot format medium - incompatible medium"}, > - {0x3007, "Cleaning failure"}, > - {0x3008, "Cannot write - application code mismatch"}, > - {0x3009, "Current session not fixated for append"}, > - {0x300A, "Cleaning request rejected"}, > - {0x300C, "WORM medium - overwrite attempted"}, > - {0x300D, "WORM medium - integrity check"}, > - {0x3010, "Medium not formatted"}, > - {0x3011, "Incompatible volume type"}, > - {0x3012, "Incompatible volume qualifier"}, > - {0x3013, "Cleaning volume expired"}, > - > - {0x3100, "Medium format corrupted"}, > - {0x3101, "Format command failed"}, > - {0x3102, "Zoned formatting failed due to spare linking"}, > - {0x3103, "Sanitize command failed"}, > - > - {0x3200, "No defect spare location available"}, > - {0x3201, "Defect list update failure"}, > - > - {0x3300, "Tape length error"}, > - > - {0x3400, "Enclosure failure"}, > - > - {0x3500, "Enclosure services failure"}, > - {0x3501, "Unsupported enclosure function"}, > - {0x3502, "Enclosure services unavailable"}, > - {0x3503, "Enclosure services transfer failure"}, > - {0x3504, "Enclosure services transfer refused"}, > - {0x3505, "Enclosure services checksum error"}, > - > - {0x3600, "Ribbon, ink, or toner failure"}, > - > - {0x3700, "Rounded parameter"}, > - > - {0x3800, "Event status notification"}, > - {0x3802, "Esn - power management class event"}, > - {0x3804, "Esn - media class event"}, > - {0x3806, "Esn - device busy class event"}, > - {0x3807, "Thin Provisioning soft threshold reached"}, > - > - {0x3900, "Saving parameters not supported"}, > - > - {0x3A00, "Medium not present"}, > - {0x3A01, "Medium not present - tray closed"}, > - {0x3A02, "Medium not present - tray open"}, > - {0x3A03, "Medium not present - loadable"}, > - {0x3A04, "Medium not present - medium auxiliary memory accessible"}, > - > - {0x3B00, "Sequential positioning error"}, > - {0x3B01, "Tape position error at beginning-of-medium"}, > - {0x3B02, "Tape position error at end-of-medium"}, > - {0x3B03, "Tape or electronic vertical forms unit not ready"}, > - {0x3B04, "Slew failure"}, > - {0x3B05, "Paper jam"}, > - {0x3B06, "Failed to sense top-of-form"}, > - {0x3B07, "Failed to sense bottom-of-form"}, > - {0x3B08, "Reposition error"}, > - {0x3B09, "Read past end of medium"}, > - {0x3B0A, "Read past beginning of medium"}, > - {0x3B0B, "Position past end of medium"}, > - {0x3B0C, "Position past beginning of medium"}, > - {0x3B0D, "Medium destination element full"}, > - {0x3B0E, "Medium source element empty"}, > - {0x3B0F, "End of medium reached"}, > - {0x3B11, "Medium magazine not accessible"}, > - {0x3B12, "Medium magazine removed"}, > - {0x3B13, "Medium magazine inserted"}, > - {0x3B14, "Medium magazine locked"}, > - {0x3B15, "Medium magazine unlocked"}, > - {0x3B16, "Mechanical positioning or changer error"}, > - {0x3B17, "Read past end of user object"}, > - {0x3B18, "Element disabled"}, > - {0x3B19, "Element enabled"}, > - {0x3B1A, "Data transfer device removed"}, > - {0x3B1B, "Data transfer device inserted"}, > - {0x3B1C, "Too many logical objects on partition to support operation"}, > - > - {0x3D00, "Invalid bits in identify message"}, > - > - {0x3E00, "Logical unit has not self-configured yet"}, > - {0x3E01, "Logical unit failure"}, > - {0x3E02, "Timeout on logical unit"}, > - {0x3E03, "Logical unit failed self-test"}, > - {0x3E04, "Logical unit unable to update self-test log"}, > - > - {0x3F00, "Target operating conditions have changed"}, > - {0x3F01, "Microcode has been changed"}, > - {0x3F02, "Changed operating definition"}, > - {0x3F03, "Inquiry data has changed"}, > - {0x3F04, "Component device attached"}, > - {0x3F05, "Device identifier changed"}, > - {0x3F06, "Redundancy group created or modified"}, > - {0x3F07, "Redundancy group deleted"}, > - {0x3F08, "Spare created or modified"}, > - {0x3F09, "Spare deleted"}, > - {0x3F0A, "Volume set created or modified"}, > - {0x3F0B, "Volume set deleted"}, > - {0x3F0C, "Volume set deassigned"}, > - {0x3F0D, "Volume set reassigned"}, > - {0x3F0E, "Reported luns data has changed"}, > - {0x3F0F, "Echo buffer overwritten"}, > - {0x3F10, "Medium loadable"}, > - {0x3F11, "Medium auxiliary memory accessible"}, > - {0x3F12, "iSCSI IP address added"}, > - {0x3F13, "iSCSI IP address removed"}, > - {0x3F14, "iSCSI IP address changed"}, > - {0x3F15, "Inspect referrals sense descriptors"}, > - {0x3F16, "Microcode has been changed without reset"}, > -/* > - * {0x40NN, "Ram failure"}, > - * {0x40NN, "Diagnostic failure on component nn"}, > - * {0x41NN, "Data path failure"}, > - * {0x42NN, "Power-on or self-test failure"}, > - */ > - {0x4300, "Message error"}, > - > - {0x4400, "Internal target failure"}, > - {0x4401, "Persistent reservation information lost"}, > - {0x4471, "ATA device failed set features"}, > - > - {0x4500, "Select or reselect failure"}, > - > - {0x4600, "Unsuccessful soft reset"}, > - > - {0x4700, "Scsi parity error"}, > - {0x4701, "Data phase CRC error detected"}, > - {0x4702, "Scsi parity error detected during st data phase"}, > - {0x4703, "Information unit iuCRC error detected"}, > - {0x4704, "Asynchronous information protection error detected"}, > - {0x4705, "Protocol service CRC error"}, > - {0x4706, "Phy test function in progress"}, > - {0x477f, "Some commands cleared by iSCSI Protocol event"}, > - > - {0x4800, "Initiator detected error message received"}, > - > - {0x4900, "Invalid message error"}, > - > - {0x4A00, "Command phase error"}, > - > - {0x4B00, "Data phase error"}, > - {0x4B01, "Invalid target port transfer tag received"}, > - {0x4B02, "Too much write data"}, > - {0x4B03, "Ack/nak timeout"}, > - {0x4B04, "Nak received"}, > - {0x4B05, "Data offset error"}, > - {0x4B06, "Initiator response timeout"}, > - {0x4B07, "Connection lost"}, > - {0x4B08, "Data-in buffer overflow - data buffer size"}, > - {0x4B09, "Data-in buffer overflow - data buffer descriptor area"}, > - {0x4B0A, "Data-in buffer error"}, > - {0x4B0B, "Data-out buffer overflow - data buffer size"}, > - {0x4B0C, "Data-out buffer overflow - data buffer descriptor area"}, > - {0x4B0D, "Data-out buffer error"}, > - {0x4B0E, "PCIe fabric error"}, > - {0x4B0F, "PCIe completion timeout"}, > - {0x4B10, "PCIe completer abort"}, > - {0x4B11, "PCIe poisoned tlp received"}, > - {0x4B12, "PCIe eCRC check failed"}, > - {0x4B13, "PCIe unsupported request"}, > - {0x4B14, "PCIe acs violation"}, > - {0x4B15, "PCIe tlp prefix blocked"}, > - > - {0x4C00, "Logical unit failed self-configuration"}, > -/* > - * {0x4DNN, "Tagged overlapped commands (nn = queue tag)"}, > - */ > - {0x4E00, "Overlapped commands attempted"}, > - > - {0x5000, "Write append error"}, > - {0x5001, "Write append position error"}, > - {0x5002, "Position error related to timing"}, > - > - {0x5100, "Erase failure"}, > - {0x5101, "Erase failure - incomplete erase operation detected"}, > - > - {0x5200, "Cartridge fault"}, > - > - {0x5300, "Media load or eject failed"}, > - {0x5301, "Unload tape failure"}, > - {0x5302, "Medium removal prevented"}, > - {0x5303, "Medium removal prevented by data transfer element"}, > - {0x5304, "Medium thread or unthread failure"}, > - {0x5305, "Volume identifier invalid"}, > - {0x5306, "Volume identifier missing"}, > - {0x5307, "Duplicate volume identifier"}, > - {0x5308, "Element status unknown"}, > - {0x5309, "Data transfer device error - load failed"}, > - {0x530a, "Data transfer device error - unload failed"}, > - {0x530b, "Data transfer device error - unload missing"}, > - {0x530c, "Data transfer device error - eject failed"}, > - {0x530d, "Data transfer device error - library communication failed"}, > - > - {0x5400, "Scsi to host system interface failure"}, > - > - {0x5500, "System resource failure"}, > - {0x5501, "System buffer full"}, > - {0x5502, "Insufficient reservation resources"}, > - {0x5503, "Insufficient resources"}, > - {0x5504, "Insufficient registration resources"}, > - {0x5505, "Insufficient access control resources"}, > - {0x5506, "Auxiliary memory out of space"}, > - {0x5507, "Quota error"}, > - {0x5508, "Maximum number of supplemental decryption keys exceeded"}, > - {0x5509, "Medium auxiliary memory not accessible"}, > - {0x550A, "Data currently unavailable"}, > - {0x550B, "Insufficient power for operation"}, > - {0x550C, "Insufficient resources to create rod"}, > - {0x550D, "Insufficient resources to create rod token"}, > - {0x550E, "Insufficient zone resources"}, > - > - {0x5700, "Unable to recover table-of-contents"}, > - > - {0x5800, "Generation does not exist"}, > - > - {0x5900, "Updated block read"}, > - > - {0x5A00, "Operator request or state change input"}, > - {0x5A01, "Operator medium removal request"}, > - {0x5A02, "Operator selected write protect"}, > - {0x5A03, "Operator selected write permit"}, > - > - {0x5B00, "Log exception"}, > - {0x5B01, "Threshold condition met"}, > - {0x5B02, "Log counter at maximum"}, > - {0x5B03, "Log list codes exhausted"}, > - > - {0x5C00, "Rpl status change"}, > - {0x5C01, "Spindles synchronized"}, > - {0x5C02, "Spindles not synchronized"}, > - > - {0x5D00, "Failure prediction threshold exceeded"}, > - {0x5D01, "Media failure prediction threshold exceeded"}, > - {0x5D02, "Logical unit failure prediction threshold exceeded"}, > - {0x5D03, "Spare area exhaustion prediction threshold exceeded"}, > - {0x5D10, "Hardware impending failure general hard drive failure"}, > - {0x5D11, "Hardware impending failure drive error rate too high"}, > - {0x5D12, "Hardware impending failure data error rate too high"}, > - {0x5D13, "Hardware impending failure seek error rate too high"}, > - {0x5D14, "Hardware impending failure too many block reassigns"}, > - {0x5D15, "Hardware impending failure access times too high"}, > - {0x5D16, "Hardware impending failure start unit times too high"}, > - {0x5D17, "Hardware impending failure channel parametrics"}, > - {0x5D18, "Hardware impending failure controller detected"}, > - {0x5D19, "Hardware impending failure throughput performance"}, > - {0x5D1A, "Hardware impending failure seek time performance"}, > - {0x5D1B, "Hardware impending failure spin-up retry count"}, > - {0x5D1C, "Hardware impending failure drive calibration retry count"}, > - {0x5D20, "Controller impending failure general hard drive failure"}, > - {0x5D21, "Controller impending failure drive error rate too high"}, > - {0x5D22, "Controller impending failure data error rate too high"}, > - {0x5D23, "Controller impending failure seek error rate too high"}, > - {0x5D24, "Controller impending failure too many block reassigns"}, > - {0x5D25, "Controller impending failure access times too high"}, > - {0x5D26, "Controller impending failure start unit times too high"}, > - {0x5D27, "Controller impending failure channel parametrics"}, > - {0x5D28, "Controller impending failure controller detected"}, > - {0x5D29, "Controller impending failure throughput performance"}, > - {0x5D2A, "Controller impending failure seek time performance"}, > - {0x5D2B, "Controller impending failure spin-up retry count"}, > - {0x5D2C, "Controller impending failure drive calibration retry count"}, > - {0x5D30, "Data channel impending failure general hard drive failure"}, > - {0x5D31, "Data channel impending failure drive error rate too high"}, > - {0x5D32, "Data channel impending failure data error rate too high"}, > - {0x5D33, "Data channel impending failure seek error rate too high"}, > - {0x5D34, "Data channel impending failure too many block reassigns"}, > - {0x5D35, "Data channel impending failure access times too high"}, > - {0x5D36, "Data channel impending failure start unit times too high"}, > - {0x5D37, "Data channel impending failure channel parametrics"}, > - {0x5D38, "Data channel impending failure controller detected"}, > - {0x5D39, "Data channel impending failure throughput performance"}, > - {0x5D3A, "Data channel impending failure seek time performance"}, > - {0x5D3B, "Data channel impending failure spin-up retry count"}, > - {0x5D3C, "Data channel impending failure drive calibration retry count"}, > - {0x5D40, "Servo impending failure general hard drive failure"}, > - {0x5D41, "Servo impending failure drive error rate too high"}, > - {0x5D42, "Servo impending failure data error rate too high"}, > - {0x5D43, "Servo impending failure seek error rate too high"}, > - {0x5D44, "Servo impending failure too many block reassigns"}, > - {0x5D45, "Servo impending failure access times too high"}, > - {0x5D46, "Servo impending failure start unit times too high"}, > - {0x5D47, "Servo impending failure channel parametrics"}, > - {0x5D48, "Servo impending failure controller detected"}, > - {0x5D49, "Servo impending failure throughput performance"}, > - {0x5D4A, "Servo impending failure seek time performance"}, > - {0x5D4B, "Servo impending failure spin-up retry count"}, > - {0x5D4C, "Servo impending failure drive calibration retry count"}, > - {0x5D50, "Spindle impending failure general hard drive failure"}, > - {0x5D51, "Spindle impending failure drive error rate too high"}, > - {0x5D52, "Spindle impending failure data error rate too high"}, > - {0x5D53, "Spindle impending failure seek error rate too high"}, > - {0x5D54, "Spindle impending failure too many block reassigns"}, > - {0x5D55, "Spindle impending failure access times too high"}, > - {0x5D56, "Spindle impending failure start unit times too high"}, > - {0x5D57, "Spindle impending failure channel parametrics"}, > - {0x5D58, "Spindle impending failure controller detected"}, > - {0x5D59, "Spindle impending failure throughput performance"}, > - {0x5D5A, "Spindle impending failure seek time performance"}, > - {0x5D5B, "Spindle impending failure spin-up retry count"}, > - {0x5D5C, "Spindle impending failure drive calibration retry count"}, > - {0x5D60, "Firmware impending failure general hard drive failure"}, > - {0x5D61, "Firmware impending failure drive error rate too high"}, > - {0x5D62, "Firmware impending failure data error rate too high"}, > - {0x5D63, "Firmware impending failure seek error rate too high"}, > - {0x5D64, "Firmware impending failure too many block reassigns"}, > - {0x5D65, "Firmware impending failure access times too high"}, > - {0x5D66, "Firmware impending failure start unit times too high"}, > - {0x5D67, "Firmware impending failure channel parametrics"}, > - {0x5D68, "Firmware impending failure controller detected"}, > - {0x5D69, "Firmware impending failure throughput performance"}, > - {0x5D6A, "Firmware impending failure seek time performance"}, > - {0x5D6B, "Firmware impending failure spin-up retry count"}, > - {0x5D6C, "Firmware impending failure drive calibration retry count"}, > - {0x5DFF, "Failure prediction threshold exceeded (false)"}, > - > - {0x5E00, "Low power condition on"}, > - {0x5E01, "Idle condition activated by timer"}, > - {0x5E02, "Standby condition activated by timer"}, > - {0x5E03, "Idle condition activated by command"}, > - {0x5E04, "Standby condition activated by command"}, > - {0x5E05, "Idle_b condition activated by timer"}, > - {0x5E06, "Idle_b condition activated by command"}, > - {0x5E07, "Idle_c condition activated by timer"}, > - {0x5E08, "Idle_c condition activated by command"}, > - {0x5E09, "Standby_y condition activated by timer"}, > - {0x5E0A, "Standby_y condition activated by command"}, > - {0x5E41, "Power state change to active"}, > - {0x5E42, "Power state change to idle"}, > - {0x5E43, "Power state change to standby"}, > - {0x5E45, "Power state change to sleep"}, > - {0x5E47, "Power state change to device control"}, > - > - {0x6000, "Lamp failure"}, > - > - {0x6100, "Video acquisition error"}, > - {0x6101, "Unable to acquire video"}, > - {0x6102, "Out of focus"}, > - > - {0x6200, "Scan head positioning error"}, > - > - {0x6300, "End of user area encountered on this track"}, > - {0x6301, "Packet does not fit in available space"}, > - > - {0x6400, "Illegal mode for this track"}, > - {0x6401, "Invalid packet size"}, > - > - {0x6500, "Voltage fault"}, > - > - {0x6600, "Automatic document feeder cover up"}, > - {0x6601, "Automatic document feeder lift up"}, > - {0x6602, "Document jam in automatic document feeder"}, > - {0x6603, "Document miss feed automatic in document feeder"}, > - > - {0x6700, "Configuration failure"}, > - {0x6701, "Configuration of incapable logical units failed"}, > - {0x6702, "Add logical unit failed"}, > - {0x6703, "Modification of logical unit failed"}, > - {0x6704, "Exchange of logical unit failed"}, > - {0x6705, "Remove of logical unit failed"}, > - {0x6706, "Attachment of logical unit failed"}, > - {0x6707, "Creation of logical unit failed"}, > - {0x6708, "Assign failure occurred"}, > - {0x6709, "Multiply assigned logical unit"}, > - {0x670A, "Set target port groups command failed"}, > - {0x670B, "ATA device feature not enabled"}, > - > - {0x6800, "Logical unit not configured"}, > - {0x6801, "Subsidiary logical unit not configured"}, > - > - {0x6900, "Data loss on logical unit"}, > - {0x6901, "Multiple logical unit failures"}, > - {0x6902, "Parity/data mismatch"}, > - > - {0x6A00, "Informational, refer to log"}, > - > - {0x6B00, "State change has occurred"}, > - {0x6B01, "Redundancy level got better"}, > - {0x6B02, "Redundancy level got worse"}, > - > - {0x6C00, "Rebuild failure occurred"}, > - > - {0x6D00, "Recalculate failure occurred"}, > - > - {0x6E00, "Command to logical unit failed"}, > - > - {0x6F00, "Copy protection key exchange failure - authentication failure"}, > - {0x6F01, "Copy protection key exchange failure - key not present"}, > - {0x6F02, "Copy protection key exchange failure - key not established"}, > - {0x6F03, "Read of scrambled sector without authentication"}, > - {0x6F04, "Media region code is mismatched to logical unit region"}, > - {0x6F05, "Drive region must be permanent/region reset count error"}, > - {0x6F06, "Insufficient block count for binding nonce recording"}, > - {0x6F07, "Conflict in binding nonce recording"}, > -/* > - * {0x70NN, "Decompression exception short algorithm id of nn"}, > - */ > - {0x7100, "Decompression exception long algorithm id"}, > - > - {0x7200, "Session fixation error"}, > - {0x7201, "Session fixation error writing lead-in"}, > - {0x7202, "Session fixation error writing lead-out"}, > - {0x7203, "Session fixation error - incomplete track in session"}, > - {0x7204, "Empty or partially written reserved track"}, > - {0x7205, "No more track reservations allowed"}, > - {0x7206, "RMZ extension is not allowed"}, > - {0x7207, "No more test zone extensions are allowed"}, > - > - {0x7300, "Cd control error"}, > - {0x7301, "Power calibration area almost full"}, > - {0x7302, "Power calibration area is full"}, > - {0x7303, "Power calibration area error"}, > - {0x7304, "Program memory area update failure"}, > - {0x7305, "Program memory area is full"}, > - {0x7306, "RMA/PMA is almost full"}, > - {0x7310, "Current power calibration area almost full"}, > - {0x7311, "Current power calibration area is full"}, > - {0x7317, "RDZ is full"}, > - > - {0x7400, "Security error"}, > - {0x7401, "Unable to decrypt data"}, > - {0x7402, "Unencrypted data encountered while decrypting"}, > - {0x7403, "Incorrect data encryption key"}, > - {0x7404, "Cryptographic integrity validation failed"}, > - {0x7405, "Error decrypting data"}, > - {0x7406, "Unknown signature verification key"}, > - {0x7407, "Encryption parameters not useable"}, > - {0x7408, "Digital signature validation failure"}, > - {0x7409, "Encryption mode mismatch on read"}, > - {0x740A, "Encrypted block not raw read enabled"}, > - {0x740B, "Incorrect Encryption parameters"}, > - {0x740C, "Unable to decrypt parameter list"}, > - {0x740D, "Encryption algorithm disabled"}, > - {0x7410, "SA creation parameter value invalid"}, > - {0x7411, "SA creation parameter value rejected"}, > - {0x7412, "Invalid SA usage"}, > - {0x7421, "Data Encryption configuration prevented"}, > - {0x7430, "SA creation parameter not supported"}, > - {0x7440, "Authentication failed"}, > - {0x7461, "External data encryption key manager access error"}, > - {0x7462, "External data encryption key manager error"}, > - {0x7463, "External data encryption key not found"}, > - {0x7464, "External data encryption request not authorized"}, > - {0x746E, "External data encryption control timeout"}, > - {0x746F, "External data encryption control error"}, > - {0x7471, "Logical unit access not authorized"}, > - {0x7479, "Security conflict in translated device"}, > - > +#define SENSE_CODE(c, s) {c, s}, > +#include "sense_codes.h" > +#undef SENSE_CODE > {0, NULL} > }; > > diff --git a/drivers/scsi/sense_codes.h b/drivers/scsi/sense_codes.h > new file mode 100644 > index 000000000000..e4e1dccd1f2f > --- /dev/null > +++ b/drivers/scsi/sense_codes.h > @@ -0,0 +1,826 @@ > +/* > + * The canonical list of T10 Additional Sense Codes is available at: > + * http://www.t10.org/lists/asc-num.txt [most recent: 20141221] > + */ > + > +SENSE_CODE(0x0000, "No additional sense information") > +SENSE_CODE(0x0001, "Filemark detected") > +SENSE_CODE(0x0002, "End-of-partition/medium detected") > +SENSE_CODE(0x0003, "Setmark detected") > +SENSE_CODE(0x0004, "Beginning-of-partition/medium detected") > +SENSE_CODE(0x0005, "End-of-data detected") > +SENSE_CODE(0x0006, "I/O process terminated") > +SENSE_CODE(0x0007, "Programmable early warning detected") > +SENSE_CODE(0x0011, "Audio play operation in progress") > +SENSE_CODE(0x0012, "Audio play operation paused") > +SENSE_CODE(0x0013, "Audio play operation successfully completed") > +SENSE_CODE(0x0014, "Audio play operation stopped due to error") > +SENSE_CODE(0x0015, "No current audio status to return") > +SENSE_CODE(0x0016, "Operation in progress") > +SENSE_CODE(0x0017, "Cleaning requested") > +SENSE_CODE(0x0018, "Erase operation in progress") > +SENSE_CODE(0x0019, "Locate operation in progress") > +SENSE_CODE(0x001A, "Rewind operation in progress") > +SENSE_CODE(0x001B, "Set capacity operation in progress") > +SENSE_CODE(0x001C, "Verify operation in progress") > +SENSE_CODE(0x001D, "ATA pass through information available") > +SENSE_CODE(0x001E, "Conflicting SA creation request") > +SENSE_CODE(0x001F, "Logical unit transitioning to another power condition") > +SENSE_CODE(0x0020, "Extended copy information available") > +SENSE_CODE(0x0021, "Atomic command aborted due to ACA") > + > +SENSE_CODE(0x0100, "No index/sector signal") > + > +SENSE_CODE(0x0200, "No seek complete") > + > +SENSE_CODE(0x0300, "Peripheral device write fault") > +SENSE_CODE(0x0301, "No write current") > +SENSE_CODE(0x0302, "Excessive write errors") > + > +SENSE_CODE(0x0400, "Logical unit not ready, cause not reportable") > +SENSE_CODE(0x0401, "Logical unit is in process of becoming ready") > +SENSE_CODE(0x0402, "Logical unit not ready, initializing command required") > +SENSE_CODE(0x0403, "Logical unit not ready, manual intervention required") > +SENSE_CODE(0x0404, "Logical unit not ready, format in progress") > +SENSE_CODE(0x0405, "Logical unit not ready, rebuild in progress") > +SENSE_CODE(0x0406, "Logical unit not ready, recalculation in progress") > +SENSE_CODE(0x0407, "Logical unit not ready, operation in progress") > +SENSE_CODE(0x0408, "Logical unit not ready, long write in progress") > +SENSE_CODE(0x0409, "Logical unit not ready, self-test in progress") > +SENSE_CODE(0x040A, "Logical unit not accessible, asymmetric access state transition") > +SENSE_CODE(0x040B, "Logical unit not accessible, target port in standby state") > +SENSE_CODE(0x040C, "Logical unit not accessible, target port in unavailable state") > +SENSE_CODE(0x040D, "Logical unit not ready, structure check required") > +SENSE_CODE(0x040E, "Logical unit not ready, security session in progress") > +SENSE_CODE(0x0410, "Logical unit not ready, auxiliary memory not accessible") > +SENSE_CODE(0x0411, "Logical unit not ready, notify (enable spinup) required") > +SENSE_CODE(0x0412, "Logical unit not ready, offline") > +SENSE_CODE(0x0413, "Logical unit not ready, SA creation in progress") > +SENSE_CODE(0x0414, "Logical unit not ready, space allocation in progress") > +SENSE_CODE(0x0415, "Logical unit not ready, robotics disabled") > +SENSE_CODE(0x0416, "Logical unit not ready, configuration required") > +SENSE_CODE(0x0417, "Logical unit not ready, calibration required") > +SENSE_CODE(0x0418, "Logical unit not ready, a door is open") > +SENSE_CODE(0x0419, "Logical unit not ready, operating in sequential mode") > +SENSE_CODE(0x041A, "Logical unit not ready, start stop unit command in progress") > +SENSE_CODE(0x041B, "Logical unit not ready, sanitize in progress") > +SENSE_CODE(0x041C, "Logical unit not ready, additional power use not yet granted") > +SENSE_CODE(0x041D, "Logical unit not ready, configuration in progress") > +SENSE_CODE(0x041E, "Logical unit not ready, microcode activation required") > +SENSE_CODE(0x041F, "Logical unit not ready, microcode download required") > +SENSE_CODE(0x0420, "Logical unit not ready, logical unit reset required") > +SENSE_CODE(0x0421, "Logical unit not ready, hard reset required") > +SENSE_CODE(0x0422, "Logical unit not ready, power cycle required") > + > +SENSE_CODE(0x0500, "Logical unit does not respond to selection") > + > +SENSE_CODE(0x0600, "No reference position found") > + > +SENSE_CODE(0x0700, "Multiple peripheral devices selected") > + > +SENSE_CODE(0x0800, "Logical unit communication failure") > +SENSE_CODE(0x0801, "Logical unit communication time-out") > +SENSE_CODE(0x0802, "Logical unit communication parity error") > +SENSE_CODE(0x0803, "Logical unit communication CRC error (Ultra-DMA/32)") > +SENSE_CODE(0x0804, "Unreachable copy target") > + > +SENSE_CODE(0x0900, "Track following error") > +SENSE_CODE(0x0901, "Tracking servo failure") > +SENSE_CODE(0x0902, "Focus servo failure") > +SENSE_CODE(0x0903, "Spindle servo failure") > +SENSE_CODE(0x0904, "Head select fault") > +SENSE_CODE(0x0905, "Vibration induced tracking error") > + > +SENSE_CODE(0x0A00, "Error log overflow") > + > +SENSE_CODE(0x0B00, "Warning") > +SENSE_CODE(0x0B01, "Warning - specified temperature exceeded") > +SENSE_CODE(0x0B02, "Warning - enclosure degraded") > +SENSE_CODE(0x0B03, "Warning - background self-test failed") > +SENSE_CODE(0x0B04, "Warning - background pre-scan detected medium error") > +SENSE_CODE(0x0B05, "Warning - background medium scan detected medium error") > +SENSE_CODE(0x0B06, "Warning - non-volatile cache now volatile") > +SENSE_CODE(0x0B07, "Warning - degraded power to non-volatile cache") > +SENSE_CODE(0x0B08, "Warning - power loss expected") > +SENSE_CODE(0x0B09, "Warning - device statistics notification active") > + > +SENSE_CODE(0x0C00, "Write error") > +SENSE_CODE(0x0C01, "Write error - recovered with auto reallocation") > +SENSE_CODE(0x0C02, "Write error - auto reallocation failed") > +SENSE_CODE(0x0C03, "Write error - recommend reassignment") > +SENSE_CODE(0x0C04, "Compression check miscompare error") > +SENSE_CODE(0x0C05, "Data expansion occurred during compression") > +SENSE_CODE(0x0C06, "Block not compressible") > +SENSE_CODE(0x0C07, "Write error - recovery needed") > +SENSE_CODE(0x0C08, "Write error - recovery failed") > +SENSE_CODE(0x0C09, "Write error - loss of streaming") > +SENSE_CODE(0x0C0A, "Write error - padding blocks added") > +SENSE_CODE(0x0C0B, "Auxiliary memory write error") > +SENSE_CODE(0x0C0C, "Write error - unexpected unsolicited data") > +SENSE_CODE(0x0C0D, "Write error - not enough unsolicited data") > +SENSE_CODE(0x0C0E, "Multiple write errors") > +SENSE_CODE(0x0C0F, "Defects in error window") > +SENSE_CODE(0x0C10, "Incomplete multiple atomic write operations") > + > +SENSE_CODE(0x0D00, "Error detected by third party temporary initiator") > +SENSE_CODE(0x0D01, "Third party device failure") > +SENSE_CODE(0x0D02, "Copy target device not reachable") > +SENSE_CODE(0x0D03, "Incorrect copy target device type") > +SENSE_CODE(0x0D04, "Copy target device data underrun") > +SENSE_CODE(0x0D05, "Copy target device data overrun") > + > +SENSE_CODE(0x0E00, "Invalid information unit") > +SENSE_CODE(0x0E01, "Information unit too short") > +SENSE_CODE(0x0E02, "Information unit too long") > +SENSE_CODE(0x0E03, "Invalid field in command information unit") > + > +SENSE_CODE(0x1000, "Id CRC or ECC error") > +SENSE_CODE(0x1001, "Logical block guard check failed") > +SENSE_CODE(0x1002, "Logical block application tag check failed") > +SENSE_CODE(0x1003, "Logical block reference tag check failed") > +SENSE_CODE(0x1004, "Logical block protection error on recover buffered data") > +SENSE_CODE(0x1005, "Logical block protection method error") > + > +SENSE_CODE(0x1100, "Unrecovered read error") > +SENSE_CODE(0x1101, "Read retries exhausted") > +SENSE_CODE(0x1102, "Error too long to correct") > +SENSE_CODE(0x1103, "Multiple read errors") > +SENSE_CODE(0x1104, "Unrecovered read error - auto reallocate failed") > +SENSE_CODE(0x1105, "L-EC uncorrectable error") > +SENSE_CODE(0x1106, "CIRC unrecovered error") > +SENSE_CODE(0x1107, "Data re-synchronization error") > +SENSE_CODE(0x1108, "Incomplete block read") > +SENSE_CODE(0x1109, "No gap found") > +SENSE_CODE(0x110A, "Miscorrected error") > +SENSE_CODE(0x110B, "Unrecovered read error - recommend reassignment") > +SENSE_CODE(0x110C, "Unrecovered read error - recommend rewrite the data") > +SENSE_CODE(0x110D, "De-compression CRC error") > +SENSE_CODE(0x110E, "Cannot decompress using declared algorithm") > +SENSE_CODE(0x110F, "Error reading UPC/EAN number") > +SENSE_CODE(0x1110, "Error reading ISRC number") > +SENSE_CODE(0x1111, "Read error - loss of streaming") > +SENSE_CODE(0x1112, "Auxiliary memory read error") > +SENSE_CODE(0x1113, "Read error - failed retransmission request") > +SENSE_CODE(0x1114, "Read error - lba marked bad by application client") > +SENSE_CODE(0x1115, "Write after sanitize required") > + > +SENSE_CODE(0x1200, "Address mark not found for id field") > + > +SENSE_CODE(0x1300, "Address mark not found for data field") > + > +SENSE_CODE(0x1400, "Recorded entity not found") > +SENSE_CODE(0x1401, "Record not found") > +SENSE_CODE(0x1402, "Filemark or setmark not found") > +SENSE_CODE(0x1403, "End-of-data not found") > +SENSE_CODE(0x1404, "Block sequence error") > +SENSE_CODE(0x1405, "Record not found - recommend reassignment") > +SENSE_CODE(0x1406, "Record not found - data auto-reallocated") > +SENSE_CODE(0x1407, "Locate operation failure") > + > +SENSE_CODE(0x1500, "Random positioning error") > +SENSE_CODE(0x1501, "Mechanical positioning error") > +SENSE_CODE(0x1502, "Positioning error detected by read of medium") > + > +SENSE_CODE(0x1600, "Data synchronization mark error") > +SENSE_CODE(0x1601, "Data sync error - data rewritten") > +SENSE_CODE(0x1602, "Data sync error - recommend rewrite") > +SENSE_CODE(0x1603, "Data sync error - data auto-reallocated") > +SENSE_CODE(0x1604, "Data sync error - recommend reassignment") > + > +SENSE_CODE(0x1700, "Recovered data with no error correction applied") > +SENSE_CODE(0x1701, "Recovered data with retries") > +SENSE_CODE(0x1702, "Recovered data with positive head offset") > +SENSE_CODE(0x1703, "Recovered data with negative head offset") > +SENSE_CODE(0x1704, "Recovered data with retries and/or circ applied") > +SENSE_CODE(0x1705, "Recovered data using previous sector id") > +SENSE_CODE(0x1706, "Recovered data without ECC - data auto-reallocated") > +SENSE_CODE(0x1707, "Recovered data without ECC - recommend reassignment") > +SENSE_CODE(0x1708, "Recovered data without ECC - recommend rewrite") > +SENSE_CODE(0x1709, "Recovered data without ECC - data rewritten") > + > +SENSE_CODE(0x1800, "Recovered data with error correction applied") > +SENSE_CODE(0x1801, "Recovered data with error corr. & retries applied") > +SENSE_CODE(0x1802, "Recovered data - data auto-reallocated") > +SENSE_CODE(0x1803, "Recovered data with CIRC") > +SENSE_CODE(0x1804, "Recovered data with L-EC") > +SENSE_CODE(0x1805, "Recovered data - recommend reassignment") > +SENSE_CODE(0x1806, "Recovered data - recommend rewrite") > +SENSE_CODE(0x1807, "Recovered data with ECC - data rewritten") > +SENSE_CODE(0x1808, "Recovered data with linking") > + > +SENSE_CODE(0x1900, "Defect list error") > +SENSE_CODE(0x1901, "Defect list not available") > +SENSE_CODE(0x1902, "Defect list error in primary list") > +SENSE_CODE(0x1903, "Defect list error in grown list") > + > +SENSE_CODE(0x1A00, "Parameter list length error") > + > +SENSE_CODE(0x1B00, "Synchronous data transfer error") > + > +SENSE_CODE(0x1C00, "Defect list not found") > +SENSE_CODE(0x1C01, "Primary defect list not found") > +SENSE_CODE(0x1C02, "Grown defect list not found") > + > +SENSE_CODE(0x1D00, "Miscompare during verify operation") > +SENSE_CODE(0x1D01, "Miscompare verify of unmapped LBA") > + > +SENSE_CODE(0x1E00, "Recovered id with ECC correction") > + > +SENSE_CODE(0x1F00, "Partial defect list transfer") > + > +SENSE_CODE(0x2000, "Invalid command operation code") > +SENSE_CODE(0x2001, "Access denied - initiator pending-enrolled") > +SENSE_CODE(0x2002, "Access denied - no access rights") > +SENSE_CODE(0x2003, "Access denied - invalid mgmt id key") > +SENSE_CODE(0x2004, "Illegal command while in write capable state") > +SENSE_CODE(0x2005, "Obsolete") > +SENSE_CODE(0x2006, "Illegal command while in explicit address mode") > +SENSE_CODE(0x2007, "Illegal command while in implicit address mode") > +SENSE_CODE(0x2008, "Access denied - enrollment conflict") > +SENSE_CODE(0x2009, "Access denied - invalid LU identifier") > +SENSE_CODE(0x200A, "Access denied - invalid proxy token") > +SENSE_CODE(0x200B, "Access denied - ACL LUN conflict") > +SENSE_CODE(0x200C, "Illegal command when not in append-only mode") > + > +SENSE_CODE(0x2100, "Logical block address out of range") > +SENSE_CODE(0x2101, "Invalid element address") > +SENSE_CODE(0x2102, "Invalid address for write") > +SENSE_CODE(0x2103, "Invalid write crossing layer jump") > +SENSE_CODE(0x2104, "Unaligned write command") > +SENSE_CODE(0x2105, "Write boundary violation") > +SENSE_CODE(0x2106, "Attempt to read invalid data") > +SENSE_CODE(0x2107, "Read boundary violation") > + > +SENSE_CODE(0x2200, "Illegal function (use 20 00, 24 00, or 26 00)") > + > +SENSE_CODE(0x2300, "Invalid token operation, cause not reportable") > +SENSE_CODE(0x2301, "Invalid token operation, unsupported token type") > +SENSE_CODE(0x2302, "Invalid token operation, remote token usage not supported") > +SENSE_CODE(0x2303, "Invalid token operation, remote rod token creation not supported") > +SENSE_CODE(0x2304, "Invalid token operation, token unknown") > +SENSE_CODE(0x2305, "Invalid token operation, token corrupt") > +SENSE_CODE(0x2306, "Invalid token operation, token revoked") > +SENSE_CODE(0x2307, "Invalid token operation, token expired") > +SENSE_CODE(0x2308, "Invalid token operation, token cancelled") > +SENSE_CODE(0x2309, "Invalid token operation, token deleted") > +SENSE_CODE(0x230A, "Invalid token operation, invalid token length") > + > +SENSE_CODE(0x2400, "Invalid field in cdb") > +SENSE_CODE(0x2401, "CDB decryption error") > +SENSE_CODE(0x2402, "Obsolete") > +SENSE_CODE(0x2403, "Obsolete") > +SENSE_CODE(0x2404, "Security audit value frozen") > +SENSE_CODE(0x2405, "Security working key frozen") > +SENSE_CODE(0x2406, "Nonce not unique") > +SENSE_CODE(0x2407, "Nonce timestamp out of range") > +SENSE_CODE(0x2408, "Invalid XCDB") > + > +SENSE_CODE(0x2500, "Logical unit not supported") > + > +SENSE_CODE(0x2600, "Invalid field in parameter list") > +SENSE_CODE(0x2601, "Parameter not supported") > +SENSE_CODE(0x2602, "Parameter value invalid") > +SENSE_CODE(0x2603, "Threshold parameters not supported") > +SENSE_CODE(0x2604, "Invalid release of persistent reservation") > +SENSE_CODE(0x2605, "Data decryption error") > +SENSE_CODE(0x2606, "Too many target descriptors") > +SENSE_CODE(0x2607, "Unsupported target descriptor type code") > +SENSE_CODE(0x2608, "Too many segment descriptors") > +SENSE_CODE(0x2609, "Unsupported segment descriptor type code") > +SENSE_CODE(0x260A, "Unexpected inexact segment") > +SENSE_CODE(0x260B, "Inline data length exceeded") > +SENSE_CODE(0x260C, "Invalid operation for copy source or destination") > +SENSE_CODE(0x260D, "Copy segment granularity violation") > +SENSE_CODE(0x260E, "Invalid parameter while port is enabled") > +SENSE_CODE(0x260F, "Invalid data-out buffer integrity check value") > +SENSE_CODE(0x2610, "Data decryption key fail limit reached") > +SENSE_CODE(0x2611, "Incomplete key-associated data set") > +SENSE_CODE(0x2612, "Vendor specific key reference not found") > + > +SENSE_CODE(0x2700, "Write protected") > +SENSE_CODE(0x2701, "Hardware write protected") > +SENSE_CODE(0x2702, "Logical unit software write protected") > +SENSE_CODE(0x2703, "Associated write protect") > +SENSE_CODE(0x2704, "Persistent write protect") > +SENSE_CODE(0x2705, "Permanent write protect") > +SENSE_CODE(0x2706, "Conditional write protect") > +SENSE_CODE(0x2707, "Space allocation failed write protect") > +SENSE_CODE(0x2708, "Zone is read only") > + > +SENSE_CODE(0x2800, "Not ready to ready change, medium may have changed") > +SENSE_CODE(0x2801, "Import or export element accessed") > +SENSE_CODE(0x2802, "Format-layer may have changed") > +SENSE_CODE(0x2803, "Import/export element accessed, medium changed") > + > +SENSE_CODE(0x2900, "Power on, reset, or bus device reset occurred") > +SENSE_CODE(0x2901, "Power on occurred") > +SENSE_CODE(0x2902, "Scsi bus reset occurred") > +SENSE_CODE(0x2903, "Bus device reset function occurred") > +SENSE_CODE(0x2904, "Device internal reset") > +SENSE_CODE(0x2905, "Transceiver mode changed to single-ended") > +SENSE_CODE(0x2906, "Transceiver mode changed to lvd") > +SENSE_CODE(0x2907, "I_T nexus loss occurred") > + > +SENSE_CODE(0x2A00, "Parameters changed") > +SENSE_CODE(0x2A01, "Mode parameters changed") > +SENSE_CODE(0x2A02, "Log parameters changed") > +SENSE_CODE(0x2A03, "Reservations preempted") > +SENSE_CODE(0x2A04, "Reservations released") > +SENSE_CODE(0x2A05, "Registrations preempted") > +SENSE_CODE(0x2A06, "Asymmetric access state changed") > +SENSE_CODE(0x2A07, "Implicit asymmetric access state transition failed") > +SENSE_CODE(0x2A08, "Priority changed") > +SENSE_CODE(0x2A09, "Capacity data has changed") > +SENSE_CODE(0x2A0A, "Error history I_T nexus cleared") > +SENSE_CODE(0x2A0B, "Error history snapshot released") > +SENSE_CODE(0x2A0C, "Error recovery attributes have changed") > +SENSE_CODE(0x2A0D, "Data encryption capabilities changed") > +SENSE_CODE(0x2A10, "Timestamp changed") > +SENSE_CODE(0x2A11, "Data encryption parameters changed by another i_t nexus") > +SENSE_CODE(0x2A12, "Data encryption parameters changed by vendor specific event") > +SENSE_CODE(0x2A13, "Data encryption key instance counter has changed") > +SENSE_CODE(0x2A14, "SA creation capabilities data has changed") > +SENSE_CODE(0x2A15, "Medium removal prevention preempted") > + > +SENSE_CODE(0x2B00, "Copy cannot execute since host cannot disconnect") > + > +SENSE_CODE(0x2C00, "Command sequence error") > +SENSE_CODE(0x2C01, "Too many windows specified") > +SENSE_CODE(0x2C02, "Invalid combination of windows specified") > +SENSE_CODE(0x2C03, "Current program area is not empty") > +SENSE_CODE(0x2C04, "Current program area is empty") > +SENSE_CODE(0x2C05, "Illegal power condition request") > +SENSE_CODE(0x2C06, "Persistent prevent conflict") > +SENSE_CODE(0x2C07, "Previous busy status") > +SENSE_CODE(0x2C08, "Previous task set full status") > +SENSE_CODE(0x2C09, "Previous reservation conflict status") > +SENSE_CODE(0x2C0A, "Partition or collection contains user objects") > +SENSE_CODE(0x2C0B, "Not reserved") > +SENSE_CODE(0x2C0C, "Orwrite generation does not match") > +SENSE_CODE(0x2C0D, "Reset write pointer not allowed") > +SENSE_CODE(0x2C0E, "Zone is offline") > + > +SENSE_CODE(0x2D00, "Overwrite error on update in place") > + > +SENSE_CODE(0x2E00, "Insufficient time for operation") > +SENSE_CODE(0x2E01, "Command timeout before processing") > +SENSE_CODE(0x2E02, "Command timeout during processing") > +SENSE_CODE(0x2E03, "Command timeout during processing due to error recovery") > + > +SENSE_CODE(0x2F00, "Commands cleared by another initiator") > +SENSE_CODE(0x2F01, "Commands cleared by power loss notification") > +SENSE_CODE(0x2F02, "Commands cleared by device server") > +SENSE_CODE(0x2F03, "Some commands cleared by queuing layer event") > + > +SENSE_CODE(0x3000, "Incompatible medium installed") > +SENSE_CODE(0x3001, "Cannot read medium - unknown format") > +SENSE_CODE(0x3002, "Cannot read medium - incompatible format") > +SENSE_CODE(0x3003, "Cleaning cartridge installed") > +SENSE_CODE(0x3004, "Cannot write medium - unknown format") > +SENSE_CODE(0x3005, "Cannot write medium - incompatible format") > +SENSE_CODE(0x3006, "Cannot format medium - incompatible medium") > +SENSE_CODE(0x3007, "Cleaning failure") > +SENSE_CODE(0x3008, "Cannot write - application code mismatch") > +SENSE_CODE(0x3009, "Current session not fixated for append") > +SENSE_CODE(0x300A, "Cleaning request rejected") > +SENSE_CODE(0x300C, "WORM medium - overwrite attempted") > +SENSE_CODE(0x300D, "WORM medium - integrity check") > +SENSE_CODE(0x3010, "Medium not formatted") > +SENSE_CODE(0x3011, "Incompatible volume type") > +SENSE_CODE(0x3012, "Incompatible volume qualifier") > +SENSE_CODE(0x3013, "Cleaning volume expired") > + > +SENSE_CODE(0x3100, "Medium format corrupted") > +SENSE_CODE(0x3101, "Format command failed") > +SENSE_CODE(0x3102, "Zoned formatting failed due to spare linking") > +SENSE_CODE(0x3103, "Sanitize command failed") > + > +SENSE_CODE(0x3200, "No defect spare location available") > +SENSE_CODE(0x3201, "Defect list update failure") > + > +SENSE_CODE(0x3300, "Tape length error") > + > +SENSE_CODE(0x3400, "Enclosure failure") > + > +SENSE_CODE(0x3500, "Enclosure services failure") > +SENSE_CODE(0x3501, "Unsupported enclosure function") > +SENSE_CODE(0x3502, "Enclosure services unavailable") > +SENSE_CODE(0x3503, "Enclosure services transfer failure") > +SENSE_CODE(0x3504, "Enclosure services transfer refused") > +SENSE_CODE(0x3505, "Enclosure services checksum error") > + > +SENSE_CODE(0x3600, "Ribbon, ink, or toner failure") > + > +SENSE_CODE(0x3700, "Rounded parameter") > + > +SENSE_CODE(0x3800, "Event status notification") > +SENSE_CODE(0x3802, "Esn - power management class event") > +SENSE_CODE(0x3804, "Esn - media class event") > +SENSE_CODE(0x3806, "Esn - device busy class event") > +SENSE_CODE(0x3807, "Thin Provisioning soft threshold reached") > + > +SENSE_CODE(0x3900, "Saving parameters not supported") > + > +SENSE_CODE(0x3A00, "Medium not present") > +SENSE_CODE(0x3A01, "Medium not present - tray closed") > +SENSE_CODE(0x3A02, "Medium not present - tray open") > +SENSE_CODE(0x3A03, "Medium not present - loadable") > +SENSE_CODE(0x3A04, "Medium not present - medium auxiliary memory accessible") > + > +SENSE_CODE(0x3B00, "Sequential positioning error") > +SENSE_CODE(0x3B01, "Tape position error at beginning-of-medium") > +SENSE_CODE(0x3B02, "Tape position error at end-of-medium") > +SENSE_CODE(0x3B03, "Tape or electronic vertical forms unit not ready") > +SENSE_CODE(0x3B04, "Slew failure") > +SENSE_CODE(0x3B05, "Paper jam") > +SENSE_CODE(0x3B06, "Failed to sense top-of-form") > +SENSE_CODE(0x3B07, "Failed to sense bottom-of-form") > +SENSE_CODE(0x3B08, "Reposition error") > +SENSE_CODE(0x3B09, "Read past end of medium") > +SENSE_CODE(0x3B0A, "Read past beginning of medium") > +SENSE_CODE(0x3B0B, "Position past end of medium") > +SENSE_CODE(0x3B0C, "Position past beginning of medium") > +SENSE_CODE(0x3B0D, "Medium destination element full") > +SENSE_CODE(0x3B0E, "Medium source element empty") > +SENSE_CODE(0x3B0F, "End of medium reached") > +SENSE_CODE(0x3B11, "Medium magazine not accessible") > +SENSE_CODE(0x3B12, "Medium magazine removed") > +SENSE_CODE(0x3B13, "Medium magazine inserted") > +SENSE_CODE(0x3B14, "Medium magazine locked") > +SENSE_CODE(0x3B15, "Medium magazine unlocked") > +SENSE_CODE(0x3B16, "Mechanical positioning or changer error") > +SENSE_CODE(0x3B17, "Read past end of user object") > +SENSE_CODE(0x3B18, "Element disabled") > +SENSE_CODE(0x3B19, "Element enabled") > +SENSE_CODE(0x3B1A, "Data transfer device removed") > +SENSE_CODE(0x3B1B, "Data transfer device inserted") > +SENSE_CODE(0x3B1C, "Too many logical objects on partition to support operation") > + > +SENSE_CODE(0x3D00, "Invalid bits in identify message") > + > +SENSE_CODE(0x3E00, "Logical unit has not self-configured yet") > +SENSE_CODE(0x3E01, "Logical unit failure") > +SENSE_CODE(0x3E02, "Timeout on logical unit") > +SENSE_CODE(0x3E03, "Logical unit failed self-test") > +SENSE_CODE(0x3E04, "Logical unit unable to update self-test log") > + > +SENSE_CODE(0x3F00, "Target operating conditions have changed") > +SENSE_CODE(0x3F01, "Microcode has been changed") > +SENSE_CODE(0x3F02, "Changed operating definition") > +SENSE_CODE(0x3F03, "Inquiry data has changed") > +SENSE_CODE(0x3F04, "Component device attached") > +SENSE_CODE(0x3F05, "Device identifier changed") > +SENSE_CODE(0x3F06, "Redundancy group created or modified") > +SENSE_CODE(0x3F07, "Redundancy group deleted") > +SENSE_CODE(0x3F08, "Spare created or modified") > +SENSE_CODE(0x3F09, "Spare deleted") > +SENSE_CODE(0x3F0A, "Volume set created or modified") > +SENSE_CODE(0x3F0B, "Volume set deleted") > +SENSE_CODE(0x3F0C, "Volume set deassigned") > +SENSE_CODE(0x3F0D, "Volume set reassigned") > +SENSE_CODE(0x3F0E, "Reported luns data has changed") > +SENSE_CODE(0x3F0F, "Echo buffer overwritten") > +SENSE_CODE(0x3F10, "Medium loadable") > +SENSE_CODE(0x3F11, "Medium auxiliary memory accessible") > +SENSE_CODE(0x3F12, "iSCSI IP address added") > +SENSE_CODE(0x3F13, "iSCSI IP address removed") > +SENSE_CODE(0x3F14, "iSCSI IP address changed") > +SENSE_CODE(0x3F15, "Inspect referrals sense descriptors") > +SENSE_CODE(0x3F16, "Microcode has been changed without reset") > +/* > + * SENSE_CODE(0x40NN, "Ram failure") > + * SENSE_CODE(0x40NN, "Diagnostic failure on component nn") > + * SENSE_CODE(0x41NN, "Data path failure") > + * SENSE_CODE(0x42NN, "Power-on or self-test failure") > + */ > +SENSE_CODE(0x4300, "Message error") > + > +SENSE_CODE(0x4400, "Internal target failure") > +SENSE_CODE(0x4401, "Persistent reservation information lost") > +SENSE_CODE(0x4471, "ATA device failed set features") > + > +SENSE_CODE(0x4500, "Select or reselect failure") > + > +SENSE_CODE(0x4600, "Unsuccessful soft reset") > + > +SENSE_CODE(0x4700, "Scsi parity error") > +SENSE_CODE(0x4701, "Data phase CRC error detected") > +SENSE_CODE(0x4702, "Scsi parity error detected during st data phase") > +SENSE_CODE(0x4703, "Information unit iuCRC error detected") > +SENSE_CODE(0x4704, "Asynchronous information protection error detected") > +SENSE_CODE(0x4705, "Protocol service CRC error") > +SENSE_CODE(0x4706, "Phy test function in progress") > +SENSE_CODE(0x477f, "Some commands cleared by iSCSI Protocol event") > + > +SENSE_CODE(0x4800, "Initiator detected error message received") > + > +SENSE_CODE(0x4900, "Invalid message error") > + > +SENSE_CODE(0x4A00, "Command phase error") > + > +SENSE_CODE(0x4B00, "Data phase error") > +SENSE_CODE(0x4B01, "Invalid target port transfer tag received") > +SENSE_CODE(0x4B02, "Too much write data") > +SENSE_CODE(0x4B03, "Ack/nak timeout") > +SENSE_CODE(0x4B04, "Nak received") > +SENSE_CODE(0x4B05, "Data offset error") > +SENSE_CODE(0x4B06, "Initiator response timeout") > +SENSE_CODE(0x4B07, "Connection lost") > +SENSE_CODE(0x4B08, "Data-in buffer overflow - data buffer size") > +SENSE_CODE(0x4B09, "Data-in buffer overflow - data buffer descriptor area") > +SENSE_CODE(0x4B0A, "Data-in buffer error") > +SENSE_CODE(0x4B0B, "Data-out buffer overflow - data buffer size") > +SENSE_CODE(0x4B0C, "Data-out buffer overflow - data buffer descriptor area") > +SENSE_CODE(0x4B0D, "Data-out buffer error") > +SENSE_CODE(0x4B0E, "PCIe fabric error") > +SENSE_CODE(0x4B0F, "PCIe completion timeout") > +SENSE_CODE(0x4B10, "PCIe completer abort") > +SENSE_CODE(0x4B11, "PCIe poisoned tlp received") > +SENSE_CODE(0x4B12, "PCIe eCRC check failed") > +SENSE_CODE(0x4B13, "PCIe unsupported request") > +SENSE_CODE(0x4B14, "PCIe acs violation") > +SENSE_CODE(0x4B15, "PCIe tlp prefix blocked") > + > +SENSE_CODE(0x4C00, "Logical unit failed self-configuration") > +/* > + * SENSE_CODE(0x4DNN, "Tagged overlapped commands (nn = queue tag)") > + */ > +SENSE_CODE(0x4E00, "Overlapped commands attempted") > + > +SENSE_CODE(0x5000, "Write append error") > +SENSE_CODE(0x5001, "Write append position error") > +SENSE_CODE(0x5002, "Position error related to timing") > + > +SENSE_CODE(0x5100, "Erase failure") > +SENSE_CODE(0x5101, "Erase failure - incomplete erase operation detected") > + > +SENSE_CODE(0x5200, "Cartridge fault") > + > +SENSE_CODE(0x5300, "Media load or eject failed") > +SENSE_CODE(0x5301, "Unload tape failure") > +SENSE_CODE(0x5302, "Medium removal prevented") > +SENSE_CODE(0x5303, "Medium removal prevented by data transfer element") > +SENSE_CODE(0x5304, "Medium thread or unthread failure") > +SENSE_CODE(0x5305, "Volume identifier invalid") > +SENSE_CODE(0x5306, "Volume identifier missing") > +SENSE_CODE(0x5307, "Duplicate volume identifier") > +SENSE_CODE(0x5308, "Element status unknown") > +SENSE_CODE(0x5309, "Data transfer device error - load failed") > +SENSE_CODE(0x530a, "Data transfer device error - unload failed") > +SENSE_CODE(0x530b, "Data transfer device error - unload missing") > +SENSE_CODE(0x530c, "Data transfer device error - eject failed") > +SENSE_CODE(0x530d, "Data transfer device error - library communication failed") > + > +SENSE_CODE(0x5400, "Scsi to host system interface failure") > + > +SENSE_CODE(0x5500, "System resource failure") > +SENSE_CODE(0x5501, "System buffer full") > +SENSE_CODE(0x5502, "Insufficient reservation resources") > +SENSE_CODE(0x5503, "Insufficient resources") > +SENSE_CODE(0x5504, "Insufficient registration resources") > +SENSE_CODE(0x5505, "Insufficient access control resources") > +SENSE_CODE(0x5506, "Auxiliary memory out of space") > +SENSE_CODE(0x5507, "Quota error") > +SENSE_CODE(0x5508, "Maximum number of supplemental decryption keys exceeded") > +SENSE_CODE(0x5509, "Medium auxiliary memory not accessible") > +SENSE_CODE(0x550A, "Data currently unavailable") > +SENSE_CODE(0x550B, "Insufficient power for operation") > +SENSE_CODE(0x550C, "Insufficient resources to create rod") > +SENSE_CODE(0x550D, "Insufficient resources to create rod token") > +SENSE_CODE(0x550E, "Insufficient zone resources") > + > +SENSE_CODE(0x5700, "Unable to recover table-of-contents") > + > +SENSE_CODE(0x5800, "Generation does not exist") > + > +SENSE_CODE(0x5900, "Updated block read") > + > +SENSE_CODE(0x5A00, "Operator request or state change input") > +SENSE_CODE(0x5A01, "Operator medium removal request") > +SENSE_CODE(0x5A02, "Operator selected write protect") > +SENSE_CODE(0x5A03, "Operator selected write permit") > + > +SENSE_CODE(0x5B00, "Log exception") > +SENSE_CODE(0x5B01, "Threshold condition met") > +SENSE_CODE(0x5B02, "Log counter at maximum") > +SENSE_CODE(0x5B03, "Log list codes exhausted") > + > +SENSE_CODE(0x5C00, "Rpl status change") > +SENSE_CODE(0x5C01, "Spindles synchronized") > +SENSE_CODE(0x5C02, "Spindles not synchronized") > + > +SENSE_CODE(0x5D00, "Failure prediction threshold exceeded") > +SENSE_CODE(0x5D01, "Media failure prediction threshold exceeded") > +SENSE_CODE(0x5D02, "Logical unit failure prediction threshold exceeded") > +SENSE_CODE(0x5D03, "Spare area exhaustion prediction threshold exceeded") > +SENSE_CODE(0x5D10, "Hardware impending failure general hard drive failure") > +SENSE_CODE(0x5D11, "Hardware impending failure drive error rate too high") > +SENSE_CODE(0x5D12, "Hardware impending failure data error rate too high") > +SENSE_CODE(0x5D13, "Hardware impending failure seek error rate too high") > +SENSE_CODE(0x5D14, "Hardware impending failure too many block reassigns") > +SENSE_CODE(0x5D15, "Hardware impending failure access times too high") > +SENSE_CODE(0x5D16, "Hardware impending failure start unit times too high") > +SENSE_CODE(0x5D17, "Hardware impending failure channel parametrics") > +SENSE_CODE(0x5D18, "Hardware impending failure controller detected") > +SENSE_CODE(0x5D19, "Hardware impending failure throughput performance") > +SENSE_CODE(0x5D1A, "Hardware impending failure seek time performance") > +SENSE_CODE(0x5D1B, "Hardware impending failure spin-up retry count") > +SENSE_CODE(0x5D1C, "Hardware impending failure drive calibration retry count") > +SENSE_CODE(0x5D20, "Controller impending failure general hard drive failure") > +SENSE_CODE(0x5D21, "Controller impending failure drive error rate too high") > +SENSE_CODE(0x5D22, "Controller impending failure data error rate too high") > +SENSE_CODE(0x5D23, "Controller impending failure seek error rate too high") > +SENSE_CODE(0x5D24, "Controller impending failure too many block reassigns") > +SENSE_CODE(0x5D25, "Controller impending failure access times too high") > +SENSE_CODE(0x5D26, "Controller impending failure start unit times too high") > +SENSE_CODE(0x5D27, "Controller impending failure channel parametrics") > +SENSE_CODE(0x5D28, "Controller impending failure controller detected") > +SENSE_CODE(0x5D29, "Controller impending failure throughput performance") > +SENSE_CODE(0x5D2A, "Controller impending failure seek time performance") > +SENSE_CODE(0x5D2B, "Controller impending failure spin-up retry count") > +SENSE_CODE(0x5D2C, "Controller impending failure drive calibration retry count") > +SENSE_CODE(0x5D30, "Data channel impending failure general hard drive failure") > +SENSE_CODE(0x5D31, "Data channel impending failure drive error rate too high") > +SENSE_CODE(0x5D32, "Data channel impending failure data error rate too high") > +SENSE_CODE(0x5D33, "Data channel impending failure seek error rate too high") > +SENSE_CODE(0x5D34, "Data channel impending failure too many block reassigns") > +SENSE_CODE(0x5D35, "Data channel impending failure access times too high") > +SENSE_CODE(0x5D36, "Data channel impending failure start unit times too high") > +SENSE_CODE(0x5D37, "Data channel impending failure channel parametrics") > +SENSE_CODE(0x5D38, "Data channel impending failure controller detected") > +SENSE_CODE(0x5D39, "Data channel impending failure throughput performance") > +SENSE_CODE(0x5D3A, "Data channel impending failure seek time performance") > +SENSE_CODE(0x5D3B, "Data channel impending failure spin-up retry count") > +SENSE_CODE(0x5D3C, "Data channel impending failure drive calibration retry count") > +SENSE_CODE(0x5D40, "Servo impending failure general hard drive failure") > +SENSE_CODE(0x5D41, "Servo impending failure drive error rate too high") > +SENSE_CODE(0x5D42, "Servo impending failure data error rate too high") > +SENSE_CODE(0x5D43, "Servo impending failure seek error rate too high") > +SENSE_CODE(0x5D44, "Servo impending failure too many block reassigns") > +SENSE_CODE(0x5D45, "Servo impending failure access times too high") > +SENSE_CODE(0x5D46, "Servo impending failure start unit times too high") > +SENSE_CODE(0x5D47, "Servo impending failure channel parametrics") > +SENSE_CODE(0x5D48, "Servo impending failure controller detected") > +SENSE_CODE(0x5D49, "Servo impending failure throughput performance") > +SENSE_CODE(0x5D4A, "Servo impending failure seek time performance") > +SENSE_CODE(0x5D4B, "Servo impending failure spin-up retry count") > +SENSE_CODE(0x5D4C, "Servo impending failure drive calibration retry count") > +SENSE_CODE(0x5D50, "Spindle impending failure general hard drive failure") > +SENSE_CODE(0x5D51, "Spindle impending failure drive error rate too high") > +SENSE_CODE(0x5D52, "Spindle impending failure data error rate too high") > +SENSE_CODE(0x5D53, "Spindle impending failure seek error rate too high") > +SENSE_CODE(0x5D54, "Spindle impending failure too many block reassigns") > +SENSE_CODE(0x5D55, "Spindle impending failure access times too high") > +SENSE_CODE(0x5D56, "Spindle impending failure start unit times too high") > +SENSE_CODE(0x5D57, "Spindle impending failure channel parametrics") > +SENSE_CODE(0x5D58, "Spindle impending failure controller detected") > +SENSE_CODE(0x5D59, "Spindle impending failure throughput performance") > +SENSE_CODE(0x5D5A, "Spindle impending failure seek time performance") > +SENSE_CODE(0x5D5B, "Spindle impending failure spin-up retry count") > +SENSE_CODE(0x5D5C, "Spindle impending failure drive calibration retry count") > +SENSE_CODE(0x5D60, "Firmware impending failure general hard drive failure") > +SENSE_CODE(0x5D61, "Firmware impending failure drive error rate too high") > +SENSE_CODE(0x5D62, "Firmware impending failure data error rate too high") > +SENSE_CODE(0x5D63, "Firmware impending failure seek error rate too high") > +SENSE_CODE(0x5D64, "Firmware impending failure too many block reassigns") > +SENSE_CODE(0x5D65, "Firmware impending failure access times too high") > +SENSE_CODE(0x5D66, "Firmware impending failure start unit times too high") > +SENSE_CODE(0x5D67, "Firmware impending failure channel parametrics") > +SENSE_CODE(0x5D68, "Firmware impending failure controller detected") > +SENSE_CODE(0x5D69, "Firmware impending failure throughput performance") > +SENSE_CODE(0x5D6A, "Firmware impending failure seek time performance") > +SENSE_CODE(0x5D6B, "Firmware impending failure spin-up retry count") > +SENSE_CODE(0x5D6C, "Firmware impending failure drive calibration retry count") > +SENSE_CODE(0x5DFF, "Failure prediction threshold exceeded (false)") > + > +SENSE_CODE(0x5E00, "Low power condition on") > +SENSE_CODE(0x5E01, "Idle condition activated by timer") > +SENSE_CODE(0x5E02, "Standby condition activated by timer") > +SENSE_CODE(0x5E03, "Idle condition activated by command") > +SENSE_CODE(0x5E04, "Standby condition activated by command") > +SENSE_CODE(0x5E05, "Idle_b condition activated by timer") > +SENSE_CODE(0x5E06, "Idle_b condition activated by command") > +SENSE_CODE(0x5E07, "Idle_c condition activated by timer") > +SENSE_CODE(0x5E08, "Idle_c condition activated by command") > +SENSE_CODE(0x5E09, "Standby_y condition activated by timer") > +SENSE_CODE(0x5E0A, "Standby_y condition activated by command") > +SENSE_CODE(0x5E41, "Power state change to active") > +SENSE_CODE(0x5E42, "Power state change to idle") > +SENSE_CODE(0x5E43, "Power state change to standby") > +SENSE_CODE(0x5E45, "Power state change to sleep") > +SENSE_CODE(0x5E47, "Power state change to device control") > + > +SENSE_CODE(0x6000, "Lamp failure") > + > +SENSE_CODE(0x6100, "Video acquisition error") > +SENSE_CODE(0x6101, "Unable to acquire video") > +SENSE_CODE(0x6102, "Out of focus") > + > +SENSE_CODE(0x6200, "Scan head positioning error") > + > +SENSE_CODE(0x6300, "End of user area encountered on this track") > +SENSE_CODE(0x6301, "Packet does not fit in available space") > + > +SENSE_CODE(0x6400, "Illegal mode for this track") > +SENSE_CODE(0x6401, "Invalid packet size") > + > +SENSE_CODE(0x6500, "Voltage fault") > + > +SENSE_CODE(0x6600, "Automatic document feeder cover up") > +SENSE_CODE(0x6601, "Automatic document feeder lift up") > +SENSE_CODE(0x6602, "Document jam in automatic document feeder") > +SENSE_CODE(0x6603, "Document miss feed automatic in document feeder") > + > +SENSE_CODE(0x6700, "Configuration failure") > +SENSE_CODE(0x6701, "Configuration of incapable logical units failed") > +SENSE_CODE(0x6702, "Add logical unit failed") > +SENSE_CODE(0x6703, "Modification of logical unit failed") > +SENSE_CODE(0x6704, "Exchange of logical unit failed") > +SENSE_CODE(0x6705, "Remove of logical unit failed") > +SENSE_CODE(0x6706, "Attachment of logical unit failed") > +SENSE_CODE(0x6707, "Creation of logical unit failed") > +SENSE_CODE(0x6708, "Assign failure occurred") > +SENSE_CODE(0x6709, "Multiply assigned logical unit") > +SENSE_CODE(0x670A, "Set target port groups command failed") > +SENSE_CODE(0x670B, "ATA device feature not enabled") > + > +SENSE_CODE(0x6800, "Logical unit not configured") > +SENSE_CODE(0x6801, "Subsidiary logical unit not configured") > + > +SENSE_CODE(0x6900, "Data loss on logical unit") > +SENSE_CODE(0x6901, "Multiple logical unit failures") > +SENSE_CODE(0x6902, "Parity/data mismatch") > + > +SENSE_CODE(0x6A00, "Informational, refer to log") > + > +SENSE_CODE(0x6B00, "State change has occurred") > +SENSE_CODE(0x6B01, "Redundancy level got better") > +SENSE_CODE(0x6B02, "Redundancy level got worse") > + > +SENSE_CODE(0x6C00, "Rebuild failure occurred") > + > +SENSE_CODE(0x6D00, "Recalculate failure occurred") > + > +SENSE_CODE(0x6E00, "Command to logical unit failed") > + > +SENSE_CODE(0x6F00, "Copy protection key exchange failure - authentication failure") > +SENSE_CODE(0x6F01, "Copy protection key exchange failure - key not present") > +SENSE_CODE(0x6F02, "Copy protection key exchange failure - key not established") > +SENSE_CODE(0x6F03, "Read of scrambled sector without authentication") > +SENSE_CODE(0x6F04, "Media region code is mismatched to logical unit region") > +SENSE_CODE(0x6F05, "Drive region must be permanent/region reset count error") > +SENSE_CODE(0x6F06, "Insufficient block count for binding nonce recording") > +SENSE_CODE(0x6F07, "Conflict in binding nonce recording") > +/* > + * SENSE_CODE(0x70NN, "Decompression exception short algorithm id of nn") > + */ > +SENSE_CODE(0x7100, "Decompression exception long algorithm id") > + > +SENSE_CODE(0x7200, "Session fixation error") > +SENSE_CODE(0x7201, "Session fixation error writing lead-in") > +SENSE_CODE(0x7202, "Session fixation error writing lead-out") > +SENSE_CODE(0x7203, "Session fixation error - incomplete track in session") > +SENSE_CODE(0x7204, "Empty or partially written reserved track") > +SENSE_CODE(0x7205, "No more track reservations allowed") > +SENSE_CODE(0x7206, "RMZ extension is not allowed") > +SENSE_CODE(0x7207, "No more test zone extensions are allowed") > + > +SENSE_CODE(0x7300, "Cd control error") > +SENSE_CODE(0x7301, "Power calibration area almost full") > +SENSE_CODE(0x7302, "Power calibration area is full") > +SENSE_CODE(0x7303, "Power calibration area error") > +SENSE_CODE(0x7304, "Program memory area update failure") > +SENSE_CODE(0x7305, "Program memory area is full") > +SENSE_CODE(0x7306, "RMA/PMA is almost full") > +SENSE_CODE(0x7310, "Current power calibration area almost full") > +SENSE_CODE(0x7311, "Current power calibration area is full") > +SENSE_CODE(0x7317, "RDZ is full") > + > +SENSE_CODE(0x7400, "Security error") > +SENSE_CODE(0x7401, "Unable to decrypt data") > +SENSE_CODE(0x7402, "Unencrypted data encountered while decrypting") > +SENSE_CODE(0x7403, "Incorrect data encryption key") > +SENSE_CODE(0x7404, "Cryptographic integrity validation failed") > +SENSE_CODE(0x7405, "Error decrypting data") > +SENSE_CODE(0x7406, "Unknown signature verification key") > +SENSE_CODE(0x7407, "Encryption parameters not useable") > +SENSE_CODE(0x7408, "Digital signature validation failure") > +SENSE_CODE(0x7409, "Encryption mode mismatch on read") > +SENSE_CODE(0x740A, "Encrypted block not raw read enabled") > +SENSE_CODE(0x740B, "Incorrect Encryption parameters") > +SENSE_CODE(0x740C, "Unable to decrypt parameter list") > +SENSE_CODE(0x740D, "Encryption algorithm disabled") > +SENSE_CODE(0x7410, "SA creation parameter value invalid") > +SENSE_CODE(0x7411, "SA creation parameter value rejected") > +SENSE_CODE(0x7412, "Invalid SA usage") > +SENSE_CODE(0x7421, "Data Encryption configuration prevented") > +SENSE_CODE(0x7430, "SA creation parameter not supported") > +SENSE_CODE(0x7440, "Authentication failed") > +SENSE_CODE(0x7461, "External data encryption key manager access error") > +SENSE_CODE(0x7462, "External data encryption key manager error") > +SENSE_CODE(0x7463, "External data encryption key not found") > +SENSE_CODE(0x7464, "External data encryption request not authorized") > +SENSE_CODE(0x746E, "External data encryption control timeout") > +SENSE_CODE(0x746F, "External data encryption control error") > +SENSE_CODE(0x7471, "Logical unit access not authorized") > +SENSE_CODE(0x7479, "Security conflict in translated device") > -- To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/scsi/constants.c b/drivers/scsi/constants.c index 58d94e3c3713..6e813eec4f8d 100644 --- a/drivers/scsi/constants.c +++ b/drivers/scsi/constants.c @@ -295,835 +295,11 @@ struct error_info { const char * text; }; -/* - * The canonical list of T10 Additional Sense Codes is available at: - * http://www.t10.org/lists/asc-num.txt [most recent: 20141221] - */ - static const struct error_info additional[] = { - {0x0000, "No additional sense information"}, - {0x0001, "Filemark detected"}, - {0x0002, "End-of-partition/medium detected"}, - {0x0003, "Setmark detected"}, - {0x0004, "Beginning-of-partition/medium detected"}, - {0x0005, "End-of-data detected"}, - {0x0006, "I/O process terminated"}, - {0x0007, "Programmable early warning detected"}, - {0x0011, "Audio play operation in progress"}, - {0x0012, "Audio play operation paused"}, - {0x0013, "Audio play operation successfully completed"}, - {0x0014, "Audio play operation stopped due to error"}, - {0x0015, "No current audio status to return"}, - {0x0016, "Operation in progress"}, - {0x0017, "Cleaning requested"}, - {0x0018, "Erase operation in progress"}, - {0x0019, "Locate operation in progress"}, - {0x001A, "Rewind operation in progress"}, - {0x001B, "Set capacity operation in progress"}, - {0x001C, "Verify operation in progress"}, - {0x001D, "ATA pass through information available"}, - {0x001E, "Conflicting SA creation request"}, - {0x001F, "Logical unit transitioning to another power condition"}, - {0x0020, "Extended copy information available"}, - {0x0021, "Atomic command aborted due to ACA"}, - - {0x0100, "No index/sector signal"}, - - {0x0200, "No seek complete"}, - - {0x0300, "Peripheral device write fault"}, - {0x0301, "No write current"}, - {0x0302, "Excessive write errors"}, - - {0x0400, "Logical unit not ready, cause not reportable"}, - {0x0401, "Logical unit is in process of becoming ready"}, - {0x0402, "Logical unit not ready, initializing command required"}, - {0x0403, "Logical unit not ready, manual intervention required"}, - {0x0404, "Logical unit not ready, format in progress"}, - {0x0405, "Logical unit not ready, rebuild in progress"}, - {0x0406, "Logical unit not ready, recalculation in progress"}, - {0x0407, "Logical unit not ready, operation in progress"}, - {0x0408, "Logical unit not ready, long write in progress"}, - {0x0409, "Logical unit not ready, self-test in progress"}, - {0x040A, "Logical unit not accessible, asymmetric access state transition"}, - {0x040B, "Logical unit not accessible, target port in standby state"}, - {0x040C, "Logical unit not accessible, target port in unavailable state"}, - {0x040D, "Logical unit not ready, structure check required"}, - {0x040E, "Logical unit not ready, security session in progress"}, - {0x0410, "Logical unit not ready, auxiliary memory not accessible"}, - {0x0411, "Logical unit not ready, notify (enable spinup) required"}, - {0x0412, "Logical unit not ready, offline"}, - {0x0413, "Logical unit not ready, SA creation in progress"}, - {0x0414, "Logical unit not ready, space allocation in progress"}, - {0x0415, "Logical unit not ready, robotics disabled"}, - {0x0416, "Logical unit not ready, configuration required"}, - {0x0417, "Logical unit not ready, calibration required"}, - {0x0418, "Logical unit not ready, a door is open"}, - {0x0419, "Logical unit not ready, operating in sequential mode"}, - {0x041A, "Logical unit not ready, start stop unit command in progress"}, - {0x041B, "Logical unit not ready, sanitize in progress"}, - {0x041C, "Logical unit not ready, additional power use not yet granted"}, - {0x041D, "Logical unit not ready, configuration in progress"}, - {0x041E, "Logical unit not ready, microcode activation required"}, - {0x041F, "Logical unit not ready, microcode download required"}, - {0x0420, "Logical unit not ready, logical unit reset required"}, - {0x0421, "Logical unit not ready, hard reset required"}, - {0x0422, "Logical unit not ready, power cycle required"}, - - {0x0500, "Logical unit does not respond to selection"}, - - {0x0600, "No reference position found"}, - - {0x0700, "Multiple peripheral devices selected"}, - - {0x0800, "Logical unit communication failure"}, - {0x0801, "Logical unit communication time-out"}, - {0x0802, "Logical unit communication parity error"}, - {0x0803, "Logical unit communication CRC error (Ultra-DMA/32)"}, - {0x0804, "Unreachable copy target"}, - - {0x0900, "Track following error"}, - {0x0901, "Tracking servo failure"}, - {0x0902, "Focus servo failure"}, - {0x0903, "Spindle servo failure"}, - {0x0904, "Head select fault"}, - {0x0905, "Vibration induced tracking error"}, - - {0x0A00, "Error log overflow"}, - - {0x0B00, "Warning"}, - {0x0B01, "Warning - specified temperature exceeded"}, - {0x0B02, "Warning - enclosure degraded"}, - {0x0B03, "Warning - background self-test failed"}, - {0x0B04, "Warning - background pre-scan detected medium error"}, - {0x0B05, "Warning - background medium scan detected medium error"}, - {0x0B06, "Warning - non-volatile cache now volatile"}, - {0x0B07, "Warning - degraded power to non-volatile cache"}, - {0x0B08, "Warning - power loss expected"}, - {0x0B09, "Warning - device statistics notification active"}, - - {0x0C00, "Write error"}, - {0x0C01, "Write error - recovered with auto reallocation"}, - {0x0C02, "Write error - auto reallocation failed"}, - {0x0C03, "Write error - recommend reassignment"}, - {0x0C04, "Compression check miscompare error"}, - {0x0C05, "Data expansion occurred during compression"}, - {0x0C06, "Block not compressible"}, - {0x0C07, "Write error - recovery needed"}, - {0x0C08, "Write error - recovery failed"}, - {0x0C09, "Write error - loss of streaming"}, - {0x0C0A, "Write error - padding blocks added"}, - {0x0C0B, "Auxiliary memory write error"}, - {0x0C0C, "Write error - unexpected unsolicited data"}, - {0x0C0D, "Write error - not enough unsolicited data"}, - {0x0C0E, "Multiple write errors"}, - {0x0C0F, "Defects in error window"}, - {0x0C10, "Incomplete multiple atomic write operations"}, - - {0x0D00, "Error detected by third party temporary initiator"}, - {0x0D01, "Third party device failure"}, - {0x0D02, "Copy target device not reachable"}, - {0x0D03, "Incorrect copy target device type"}, - {0x0D04, "Copy target device data underrun"}, - {0x0D05, "Copy target device data overrun"}, - - {0x0E00, "Invalid information unit"}, - {0x0E01, "Information unit too short"}, - {0x0E02, "Information unit too long"}, - {0x0E03, "Invalid field in command information unit"}, - - {0x1000, "Id CRC or ECC error"}, - {0x1001, "Logical block guard check failed"}, - {0x1002, "Logical block application tag check failed"}, - {0x1003, "Logical block reference tag check failed"}, - {0x1004, "Logical block protection error on recover buffered data"}, - {0x1005, "Logical block protection method error"}, - - {0x1100, "Unrecovered read error"}, - {0x1101, "Read retries exhausted"}, - {0x1102, "Error too long to correct"}, - {0x1103, "Multiple read errors"}, - {0x1104, "Unrecovered read error - auto reallocate failed"}, - {0x1105, "L-EC uncorrectable error"}, - {0x1106, "CIRC unrecovered error"}, - {0x1107, "Data re-synchronization error"}, - {0x1108, "Incomplete block read"}, - {0x1109, "No gap found"}, - {0x110A, "Miscorrected error"}, - {0x110B, "Unrecovered read error - recommend reassignment"}, - {0x110C, "Unrecovered read error - recommend rewrite the data"}, - {0x110D, "De-compression CRC error"}, - {0x110E, "Cannot decompress using declared algorithm"}, - {0x110F, "Error reading UPC/EAN number"}, - {0x1110, "Error reading ISRC number"}, - {0x1111, "Read error - loss of streaming"}, - {0x1112, "Auxiliary memory read error"}, - {0x1113, "Read error - failed retransmission request"}, - {0x1114, "Read error - lba marked bad by application client"}, - {0x1115, "Write after sanitize required"}, - - {0x1200, "Address mark not found for id field"}, - - {0x1300, "Address mark not found for data field"}, - - {0x1400, "Recorded entity not found"}, - {0x1401, "Record not found"}, - {0x1402, "Filemark or setmark not found"}, - {0x1403, "End-of-data not found"}, - {0x1404, "Block sequence error"}, - {0x1405, "Record not found - recommend reassignment"}, - {0x1406, "Record not found - data auto-reallocated"}, - {0x1407, "Locate operation failure"}, - - {0x1500, "Random positioning error"}, - {0x1501, "Mechanical positioning error"}, - {0x1502, "Positioning error detected by read of medium"}, - - {0x1600, "Data synchronization mark error"}, - {0x1601, "Data sync error - data rewritten"}, - {0x1602, "Data sync error - recommend rewrite"}, - {0x1603, "Data sync error - data auto-reallocated"}, - {0x1604, "Data sync error - recommend reassignment"}, - - {0x1700, "Recovered data with no error correction applied"}, - {0x1701, "Recovered data with retries"}, - {0x1702, "Recovered data with positive head offset"}, - {0x1703, "Recovered data with negative head offset"}, - {0x1704, "Recovered data with retries and/or circ applied"}, - {0x1705, "Recovered data using previous sector id"}, - {0x1706, "Recovered data without ECC - data auto-reallocated"}, - {0x1707, "Recovered data without ECC - recommend reassignment"}, - {0x1708, "Recovered data without ECC - recommend rewrite"}, - {0x1709, "Recovered data without ECC - data rewritten"}, - - {0x1800, "Recovered data with error correction applied"}, - {0x1801, "Recovered data with error corr. & retries applied"}, - {0x1802, "Recovered data - data auto-reallocated"}, - {0x1803, "Recovered data with CIRC"}, - {0x1804, "Recovered data with L-EC"}, - {0x1805, "Recovered data - recommend reassignment"}, - {0x1806, "Recovered data - recommend rewrite"}, - {0x1807, "Recovered data with ECC - data rewritten"}, - {0x1808, "Recovered data with linking"}, - - {0x1900, "Defect list error"}, - {0x1901, "Defect list not available"}, - {0x1902, "Defect list error in primary list"}, - {0x1903, "Defect list error in grown list"}, - - {0x1A00, "Parameter list length error"}, - - {0x1B00, "Synchronous data transfer error"}, - - {0x1C00, "Defect list not found"}, - {0x1C01, "Primary defect list not found"}, - {0x1C02, "Grown defect list not found"}, - - {0x1D00, "Miscompare during verify operation"}, - {0x1D01, "Miscompare verify of unmapped LBA"}, - - {0x1E00, "Recovered id with ECC correction"}, - - {0x1F00, "Partial defect list transfer"}, - - {0x2000, "Invalid command operation code"}, - {0x2001, "Access denied - initiator pending-enrolled"}, - {0x2002, "Access denied - no access rights"}, - {0x2003, "Access denied - invalid mgmt id key"}, - {0x2004, "Illegal command while in write capable state"}, - {0x2005, "Obsolete"}, - {0x2006, "Illegal command while in explicit address mode"}, - {0x2007, "Illegal command while in implicit address mode"}, - {0x2008, "Access denied - enrollment conflict"}, - {0x2009, "Access denied - invalid LU identifier"}, - {0x200A, "Access denied - invalid proxy token"}, - {0x200B, "Access denied - ACL LUN conflict"}, - {0x200C, "Illegal command when not in append-only mode"}, - - {0x2100, "Logical block address out of range"}, - {0x2101, "Invalid element address"}, - {0x2102, "Invalid address for write"}, - {0x2103, "Invalid write crossing layer jump"}, - {0x2104, "Unaligned write command"}, - {0x2105, "Write boundary violation"}, - {0x2106, "Attempt to read invalid data"}, - {0x2107, "Read boundary violation"}, - - {0x2200, "Illegal function (use 20 00, 24 00, or 26 00)"}, - - {0x2300, "Invalid token operation, cause not reportable"}, - {0x2301, "Invalid token operation, unsupported token type"}, - {0x2302, "Invalid token operation, remote token usage not supported"}, - {0x2303, "Invalid token operation, remote rod token creation not supported"}, - {0x2304, "Invalid token operation, token unknown"}, - {0x2305, "Invalid token operation, token corrupt"}, - {0x2306, "Invalid token operation, token revoked"}, - {0x2307, "Invalid token operation, token expired"}, - {0x2308, "Invalid token operation, token cancelled"}, - {0x2309, "Invalid token operation, token deleted"}, - {0x230A, "Invalid token operation, invalid token length"}, - - {0x2400, "Invalid field in cdb"}, - {0x2401, "CDB decryption error"}, - {0x2402, "Obsolete"}, - {0x2403, "Obsolete"}, - {0x2404, "Security audit value frozen"}, - {0x2405, "Security working key frozen"}, - {0x2406, "Nonce not unique"}, - {0x2407, "Nonce timestamp out of range"}, - {0x2408, "Invalid XCDB"}, - - {0x2500, "Logical unit not supported"}, - - {0x2600, "Invalid field in parameter list"}, - {0x2601, "Parameter not supported"}, - {0x2602, "Parameter value invalid"}, - {0x2603, "Threshold parameters not supported"}, - {0x2604, "Invalid release of persistent reservation"}, - {0x2605, "Data decryption error"}, - {0x2606, "Too many target descriptors"}, - {0x2607, "Unsupported target descriptor type code"}, - {0x2608, "Too many segment descriptors"}, - {0x2609, "Unsupported segment descriptor type code"}, - {0x260A, "Unexpected inexact segment"}, - {0x260B, "Inline data length exceeded"}, - {0x260C, "Invalid operation for copy source or destination"}, - {0x260D, "Copy segment granularity violation"}, - {0x260E, "Invalid parameter while port is enabled"}, - {0x260F, "Invalid data-out buffer integrity check value"}, - {0x2610, "Data decryption key fail limit reached"}, - {0x2611, "Incomplete key-associated data set"}, - {0x2612, "Vendor specific key reference not found"}, - - {0x2700, "Write protected"}, - {0x2701, "Hardware write protected"}, - {0x2702, "Logical unit software write protected"}, - {0x2703, "Associated write protect"}, - {0x2704, "Persistent write protect"}, - {0x2705, "Permanent write protect"}, - {0x2706, "Conditional write protect"}, - {0x2707, "Space allocation failed write protect"}, - {0x2708, "Zone is read only"}, - - {0x2800, "Not ready to ready change, medium may have changed"}, - {0x2801, "Import or export element accessed"}, - {0x2802, "Format-layer may have changed"}, - {0x2803, "Import/export element accessed, medium changed"}, - - {0x2900, "Power on, reset, or bus device reset occurred"}, - {0x2901, "Power on occurred"}, - {0x2902, "Scsi bus reset occurred"}, - {0x2903, "Bus device reset function occurred"}, - {0x2904, "Device internal reset"}, - {0x2905, "Transceiver mode changed to single-ended"}, - {0x2906, "Transceiver mode changed to lvd"}, - {0x2907, "I_T nexus loss occurred"}, - - {0x2A00, "Parameters changed"}, - {0x2A01, "Mode parameters changed"}, - {0x2A02, "Log parameters changed"}, - {0x2A03, "Reservations preempted"}, - {0x2A04, "Reservations released"}, - {0x2A05, "Registrations preempted"}, - {0x2A06, "Asymmetric access state changed"}, - {0x2A07, "Implicit asymmetric access state transition failed"}, - {0x2A08, "Priority changed"}, - {0x2A09, "Capacity data has changed"}, - {0x2A0A, "Error history I_T nexus cleared"}, - {0x2A0B, "Error history snapshot released"}, - {0x2A0C, "Error recovery attributes have changed"}, - {0x2A0D, "Data encryption capabilities changed"}, - {0x2A10, "Timestamp changed"}, - {0x2A11, "Data encryption parameters changed by another i_t nexus"}, - {0x2A12, "Data encryption parameters changed by vendor specific event"}, - {0x2A13, "Data encryption key instance counter has changed"}, - {0x2A14, "SA creation capabilities data has changed"}, - {0x2A15, "Medium removal prevention preempted"}, - - {0x2B00, "Copy cannot execute since host cannot disconnect"}, - - {0x2C00, "Command sequence error"}, - {0x2C01, "Too many windows specified"}, - {0x2C02, "Invalid combination of windows specified"}, - {0x2C03, "Current program area is not empty"}, - {0x2C04, "Current program area is empty"}, - {0x2C05, "Illegal power condition request"}, - {0x2C06, "Persistent prevent conflict"}, - {0x2C07, "Previous busy status"}, - {0x2C08, "Previous task set full status"}, - {0x2C09, "Previous reservation conflict status"}, - {0x2C0A, "Partition or collection contains user objects"}, - {0x2C0B, "Not reserved"}, - {0x2C0C, "Orwrite generation does not match"}, - {0x2C0D, "Reset write pointer not allowed"}, - {0x2C0E, "Zone is offline"}, - - {0x2D00, "Overwrite error on update in place"}, - - {0x2E00, "Insufficient time for operation"}, - {0x2E01, "Command timeout before processing"}, - {0x2E02, "Command timeout during processing"}, - {0x2E03, "Command timeout during processing due to error recovery"}, - - {0x2F00, "Commands cleared by another initiator"}, - {0x2F01, "Commands cleared by power loss notification"}, - {0x2F02, "Commands cleared by device server"}, - {0x2F03, "Some commands cleared by queuing layer event"}, - - {0x3000, "Incompatible medium installed"}, - {0x3001, "Cannot read medium - unknown format"}, - {0x3002, "Cannot read medium - incompatible format"}, - {0x3003, "Cleaning cartridge installed"}, - {0x3004, "Cannot write medium - unknown format"}, - {0x3005, "Cannot write medium - incompatible format"}, - {0x3006, "Cannot format medium - incompatible medium"}, - {0x3007, "Cleaning failure"}, - {0x3008, "Cannot write - application code mismatch"}, - {0x3009, "Current session not fixated for append"}, - {0x300A, "Cleaning request rejected"}, - {0x300C, "WORM medium - overwrite attempted"}, - {0x300D, "WORM medium - integrity check"}, - {0x3010, "Medium not formatted"}, - {0x3011, "Incompatible volume type"}, - {0x3012, "Incompatible volume qualifier"}, - {0x3013, "Cleaning volume expired"}, - - {0x3100, "Medium format corrupted"}, - {0x3101, "Format command failed"}, - {0x3102, "Zoned formatting failed due to spare linking"}, - {0x3103, "Sanitize command failed"}, - - {0x3200, "No defect spare location available"}, - {0x3201, "Defect list update failure"}, - - {0x3300, "Tape length error"}, - - {0x3400, "Enclosure failure"}, - - {0x3500, "Enclosure services failure"}, - {0x3501, "Unsupported enclosure function"}, - {0x3502, "Enclosure services unavailable"}, - {0x3503, "Enclosure services transfer failure"}, - {0x3504, "Enclosure services transfer refused"}, - {0x3505, "Enclosure services checksum error"}, - - {0x3600, "Ribbon, ink, or toner failure"}, - - {0x3700, "Rounded parameter"}, - - {0x3800, "Event status notification"}, - {0x3802, "Esn - power management class event"}, - {0x3804, "Esn - media class event"}, - {0x3806, "Esn - device busy class event"}, - {0x3807, "Thin Provisioning soft threshold reached"}, - - {0x3900, "Saving parameters not supported"}, - - {0x3A00, "Medium not present"}, - {0x3A01, "Medium not present - tray closed"}, - {0x3A02, "Medium not present - tray open"}, - {0x3A03, "Medium not present - loadable"}, - {0x3A04, "Medium not present - medium auxiliary memory accessible"}, - - {0x3B00, "Sequential positioning error"}, - {0x3B01, "Tape position error at beginning-of-medium"}, - {0x3B02, "Tape position error at end-of-medium"}, - {0x3B03, "Tape or electronic vertical forms unit not ready"}, - {0x3B04, "Slew failure"}, - {0x3B05, "Paper jam"}, - {0x3B06, "Failed to sense top-of-form"}, - {0x3B07, "Failed to sense bottom-of-form"}, - {0x3B08, "Reposition error"}, - {0x3B09, "Read past end of medium"}, - {0x3B0A, "Read past beginning of medium"}, - {0x3B0B, "Position past end of medium"}, - {0x3B0C, "Position past beginning of medium"}, - {0x3B0D, "Medium destination element full"}, - {0x3B0E, "Medium source element empty"}, - {0x3B0F, "End of medium reached"}, - {0x3B11, "Medium magazine not accessible"}, - {0x3B12, "Medium magazine removed"}, - {0x3B13, "Medium magazine inserted"}, - {0x3B14, "Medium magazine locked"}, - {0x3B15, "Medium magazine unlocked"}, - {0x3B16, "Mechanical positioning or changer error"}, - {0x3B17, "Read past end of user object"}, - {0x3B18, "Element disabled"}, - {0x3B19, "Element enabled"}, - {0x3B1A, "Data transfer device removed"}, - {0x3B1B, "Data transfer device inserted"}, - {0x3B1C, "Too many logical objects on partition to support operation"}, - - {0x3D00, "Invalid bits in identify message"}, - - {0x3E00, "Logical unit has not self-configured yet"}, - {0x3E01, "Logical unit failure"}, - {0x3E02, "Timeout on logical unit"}, - {0x3E03, "Logical unit failed self-test"}, - {0x3E04, "Logical unit unable to update self-test log"}, - - {0x3F00, "Target operating conditions have changed"}, - {0x3F01, "Microcode has been changed"}, - {0x3F02, "Changed operating definition"}, - {0x3F03, "Inquiry data has changed"}, - {0x3F04, "Component device attached"}, - {0x3F05, "Device identifier changed"}, - {0x3F06, "Redundancy group created or modified"}, - {0x3F07, "Redundancy group deleted"}, - {0x3F08, "Spare created or modified"}, - {0x3F09, "Spare deleted"}, - {0x3F0A, "Volume set created or modified"}, - {0x3F0B, "Volume set deleted"}, - {0x3F0C, "Volume set deassigned"}, - {0x3F0D, "Volume set reassigned"}, - {0x3F0E, "Reported luns data has changed"}, - {0x3F0F, "Echo buffer overwritten"}, - {0x3F10, "Medium loadable"}, - {0x3F11, "Medium auxiliary memory accessible"}, - {0x3F12, "iSCSI IP address added"}, - {0x3F13, "iSCSI IP address removed"}, - {0x3F14, "iSCSI IP address changed"}, - {0x3F15, "Inspect referrals sense descriptors"}, - {0x3F16, "Microcode has been changed without reset"}, -/* - * {0x40NN, "Ram failure"}, - * {0x40NN, "Diagnostic failure on component nn"}, - * {0x41NN, "Data path failure"}, - * {0x42NN, "Power-on or self-test failure"}, - */ - {0x4300, "Message error"}, - - {0x4400, "Internal target failure"}, - {0x4401, "Persistent reservation information lost"}, - {0x4471, "ATA device failed set features"}, - - {0x4500, "Select or reselect failure"}, - - {0x4600, "Unsuccessful soft reset"}, - - {0x4700, "Scsi parity error"}, - {0x4701, "Data phase CRC error detected"}, - {0x4702, "Scsi parity error detected during st data phase"}, - {0x4703, "Information unit iuCRC error detected"}, - {0x4704, "Asynchronous information protection error detected"}, - {0x4705, "Protocol service CRC error"}, - {0x4706, "Phy test function in progress"}, - {0x477f, "Some commands cleared by iSCSI Protocol event"}, - - {0x4800, "Initiator detected error message received"}, - - {0x4900, "Invalid message error"}, - - {0x4A00, "Command phase error"}, - - {0x4B00, "Data phase error"}, - {0x4B01, "Invalid target port transfer tag received"}, - {0x4B02, "Too much write data"}, - {0x4B03, "Ack/nak timeout"}, - {0x4B04, "Nak received"}, - {0x4B05, "Data offset error"}, - {0x4B06, "Initiator response timeout"}, - {0x4B07, "Connection lost"}, - {0x4B08, "Data-in buffer overflow - data buffer size"}, - {0x4B09, "Data-in buffer overflow - data buffer descriptor area"}, - {0x4B0A, "Data-in buffer error"}, - {0x4B0B, "Data-out buffer overflow - data buffer size"}, - {0x4B0C, "Data-out buffer overflow - data buffer descriptor area"}, - {0x4B0D, "Data-out buffer error"}, - {0x4B0E, "PCIe fabric error"}, - {0x4B0F, "PCIe completion timeout"}, - {0x4B10, "PCIe completer abort"}, - {0x4B11, "PCIe poisoned tlp received"}, - {0x4B12, "PCIe eCRC check failed"}, - {0x4B13, "PCIe unsupported request"}, - {0x4B14, "PCIe acs violation"}, - {0x4B15, "PCIe tlp prefix blocked"}, - - {0x4C00, "Logical unit failed self-configuration"}, -/* - * {0x4DNN, "Tagged overlapped commands (nn = queue tag)"}, - */ - {0x4E00, "Overlapped commands attempted"}, - - {0x5000, "Write append error"}, - {0x5001, "Write append position error"}, - {0x5002, "Position error related to timing"}, - - {0x5100, "Erase failure"}, - {0x5101, "Erase failure - incomplete erase operation detected"}, - - {0x5200, "Cartridge fault"}, - - {0x5300, "Media load or eject failed"}, - {0x5301, "Unload tape failure"}, - {0x5302, "Medium removal prevented"}, - {0x5303, "Medium removal prevented by data transfer element"}, - {0x5304, "Medium thread or unthread failure"}, - {0x5305, "Volume identifier invalid"}, - {0x5306, "Volume identifier missing"}, - {0x5307, "Duplicate volume identifier"}, - {0x5308, "Element status unknown"}, - {0x5309, "Data transfer device error - load failed"}, - {0x530a, "Data transfer device error - unload failed"}, - {0x530b, "Data transfer device error - unload missing"}, - {0x530c, "Data transfer device error - eject failed"}, - {0x530d, "Data transfer device error - library communication failed"}, - - {0x5400, "Scsi to host system interface failure"}, - - {0x5500, "System resource failure"}, - {0x5501, "System buffer full"}, - {0x5502, "Insufficient reservation resources"}, - {0x5503, "Insufficient resources"}, - {0x5504, "Insufficient registration resources"}, - {0x5505, "Insufficient access control resources"}, - {0x5506, "Auxiliary memory out of space"}, - {0x5507, "Quota error"}, - {0x5508, "Maximum number of supplemental decryption keys exceeded"}, - {0x5509, "Medium auxiliary memory not accessible"}, - {0x550A, "Data currently unavailable"}, - {0x550B, "Insufficient power for operation"}, - {0x550C, "Insufficient resources to create rod"}, - {0x550D, "Insufficient resources to create rod token"}, - {0x550E, "Insufficient zone resources"}, - - {0x5700, "Unable to recover table-of-contents"}, - - {0x5800, "Generation does not exist"}, - - {0x5900, "Updated block read"}, - - {0x5A00, "Operator request or state change input"}, - {0x5A01, "Operator medium removal request"}, - {0x5A02, "Operator selected write protect"}, - {0x5A03, "Operator selected write permit"}, - - {0x5B00, "Log exception"}, - {0x5B01, "Threshold condition met"}, - {0x5B02, "Log counter at maximum"}, - {0x5B03, "Log list codes exhausted"}, - - {0x5C00, "Rpl status change"}, - {0x5C01, "Spindles synchronized"}, - {0x5C02, "Spindles not synchronized"}, - - {0x5D00, "Failure prediction threshold exceeded"}, - {0x5D01, "Media failure prediction threshold exceeded"}, - {0x5D02, "Logical unit failure prediction threshold exceeded"}, - {0x5D03, "Spare area exhaustion prediction threshold exceeded"}, - {0x5D10, "Hardware impending failure general hard drive failure"}, - {0x5D11, "Hardware impending failure drive error rate too high"}, - {0x5D12, "Hardware impending failure data error rate too high"}, - {0x5D13, "Hardware impending failure seek error rate too high"}, - {0x5D14, "Hardware impending failure too many block reassigns"}, - {0x5D15, "Hardware impending failure access times too high"}, - {0x5D16, "Hardware impending failure start unit times too high"}, - {0x5D17, "Hardware impending failure channel parametrics"}, - {0x5D18, "Hardware impending failure controller detected"}, - {0x5D19, "Hardware impending failure throughput performance"}, - {0x5D1A, "Hardware impending failure seek time performance"}, - {0x5D1B, "Hardware impending failure spin-up retry count"}, - {0x5D1C, "Hardware impending failure drive calibration retry count"}, - {0x5D20, "Controller impending failure general hard drive failure"}, - {0x5D21, "Controller impending failure drive error rate too high"}, - {0x5D22, "Controller impending failure data error rate too high"}, - {0x5D23, "Controller impending failure seek error rate too high"}, - {0x5D24, "Controller impending failure too many block reassigns"}, - {0x5D25, "Controller impending failure access times too high"}, - {0x5D26, "Controller impending failure start unit times too high"}, - {0x5D27, "Controller impending failure channel parametrics"}, - {0x5D28, "Controller impending failure controller detected"}, - {0x5D29, "Controller impending failure throughput performance"}, - {0x5D2A, "Controller impending failure seek time performance"}, - {0x5D2B, "Controller impending failure spin-up retry count"}, - {0x5D2C, "Controller impending failure drive calibration retry count"}, - {0x5D30, "Data channel impending failure general hard drive failure"}, - {0x5D31, "Data channel impending failure drive error rate too high"}, - {0x5D32, "Data channel impending failure data error rate too high"}, - {0x5D33, "Data channel impending failure seek error rate too high"}, - {0x5D34, "Data channel impending failure too many block reassigns"}, - {0x5D35, "Data channel impending failure access times too high"}, - {0x5D36, "Data channel impending failure start unit times too high"}, - {0x5D37, "Data channel impending failure channel parametrics"}, - {0x5D38, "Data channel impending failure controller detected"}, - {0x5D39, "Data channel impending failure throughput performance"}, - {0x5D3A, "Data channel impending failure seek time performance"}, - {0x5D3B, "Data channel impending failure spin-up retry count"}, - {0x5D3C, "Data channel impending failure drive calibration retry count"}, - {0x5D40, "Servo impending failure general hard drive failure"}, - {0x5D41, "Servo impending failure drive error rate too high"}, - {0x5D42, "Servo impending failure data error rate too high"}, - {0x5D43, "Servo impending failure seek error rate too high"}, - {0x5D44, "Servo impending failure too many block reassigns"}, - {0x5D45, "Servo impending failure access times too high"}, - {0x5D46, "Servo impending failure start unit times too high"}, - {0x5D47, "Servo impending failure channel parametrics"}, - {0x5D48, "Servo impending failure controller detected"}, - {0x5D49, "Servo impending failure throughput performance"}, - {0x5D4A, "Servo impending failure seek time performance"}, - {0x5D4B, "Servo impending failure spin-up retry count"}, - {0x5D4C, "Servo impending failure drive calibration retry count"}, - {0x5D50, "Spindle impending failure general hard drive failure"}, - {0x5D51, "Spindle impending failure drive error rate too high"}, - {0x5D52, "Spindle impending failure data error rate too high"}, - {0x5D53, "Spindle impending failure seek error rate too high"}, - {0x5D54, "Spindle impending failure too many block reassigns"}, - {0x5D55, "Spindle impending failure access times too high"}, - {0x5D56, "Spindle impending failure start unit times too high"}, - {0x5D57, "Spindle impending failure channel parametrics"}, - {0x5D58, "Spindle impending failure controller detected"}, - {0x5D59, "Spindle impending failure throughput performance"}, - {0x5D5A, "Spindle impending failure seek time performance"}, - {0x5D5B, "Spindle impending failure spin-up retry count"}, - {0x5D5C, "Spindle impending failure drive calibration retry count"}, - {0x5D60, "Firmware impending failure general hard drive failure"}, - {0x5D61, "Firmware impending failure drive error rate too high"}, - {0x5D62, "Firmware impending failure data error rate too high"}, - {0x5D63, "Firmware impending failure seek error rate too high"}, - {0x5D64, "Firmware impending failure too many block reassigns"}, - {0x5D65, "Firmware impending failure access times too high"}, - {0x5D66, "Firmware impending failure start unit times too high"}, - {0x5D67, "Firmware impending failure channel parametrics"}, - {0x5D68, "Firmware impending failure controller detected"}, - {0x5D69, "Firmware impending failure throughput performance"}, - {0x5D6A, "Firmware impending failure seek time performance"}, - {0x5D6B, "Firmware impending failure spin-up retry count"}, - {0x5D6C, "Firmware impending failure drive calibration retry count"}, - {0x5DFF, "Failure prediction threshold exceeded (false)"}, - - {0x5E00, "Low power condition on"}, - {0x5E01, "Idle condition activated by timer"}, - {0x5E02, "Standby condition activated by timer"}, - {0x5E03, "Idle condition activated by command"}, - {0x5E04, "Standby condition activated by command"}, - {0x5E05, "Idle_b condition activated by timer"}, - {0x5E06, "Idle_b condition activated by command"}, - {0x5E07, "Idle_c condition activated by timer"}, - {0x5E08, "Idle_c condition activated by command"}, - {0x5E09, "Standby_y condition activated by timer"}, - {0x5E0A, "Standby_y condition activated by command"}, - {0x5E41, "Power state change to active"}, - {0x5E42, "Power state change to idle"}, - {0x5E43, "Power state change to standby"}, - {0x5E45, "Power state change to sleep"}, - {0x5E47, "Power state change to device control"}, - - {0x6000, "Lamp failure"}, - - {0x6100, "Video acquisition error"}, - {0x6101, "Unable to acquire video"}, - {0x6102, "Out of focus"}, - - {0x6200, "Scan head positioning error"}, - - {0x6300, "End of user area encountered on this track"}, - {0x6301, "Packet does not fit in available space"}, - - {0x6400, "Illegal mode for this track"}, - {0x6401, "Invalid packet size"}, - - {0x6500, "Voltage fault"}, - - {0x6600, "Automatic document feeder cover up"}, - {0x6601, "Automatic document feeder lift up"}, - {0x6602, "Document jam in automatic document feeder"}, - {0x6603, "Document miss feed automatic in document feeder"}, - - {0x6700, "Configuration failure"}, - {0x6701, "Configuration of incapable logical units failed"}, - {0x6702, "Add logical unit failed"}, - {0x6703, "Modification of logical unit failed"}, - {0x6704, "Exchange of logical unit failed"}, - {0x6705, "Remove of logical unit failed"}, - {0x6706, "Attachment of logical unit failed"}, - {0x6707, "Creation of logical unit failed"}, - {0x6708, "Assign failure occurred"}, - {0x6709, "Multiply assigned logical unit"}, - {0x670A, "Set target port groups command failed"}, - {0x670B, "ATA device feature not enabled"}, - - {0x6800, "Logical unit not configured"}, - {0x6801, "Subsidiary logical unit not configured"}, - - {0x6900, "Data loss on logical unit"}, - {0x6901, "Multiple logical unit failures"}, - {0x6902, "Parity/data mismatch"}, - - {0x6A00, "Informational, refer to log"}, - - {0x6B00, "State change has occurred"}, - {0x6B01, "Redundancy level got better"}, - {0x6B02, "Redundancy level got worse"}, - - {0x6C00, "Rebuild failure occurred"}, - - {0x6D00, "Recalculate failure occurred"}, - - {0x6E00, "Command to logical unit failed"}, - - {0x6F00, "Copy protection key exchange failure - authentication failure"}, - {0x6F01, "Copy protection key exchange failure - key not present"}, - {0x6F02, "Copy protection key exchange failure - key not established"}, - {0x6F03, "Read of scrambled sector without authentication"}, - {0x6F04, "Media region code is mismatched to logical unit region"}, - {0x6F05, "Drive region must be permanent/region reset count error"}, - {0x6F06, "Insufficient block count for binding nonce recording"}, - {0x6F07, "Conflict in binding nonce recording"}, -/* - * {0x70NN, "Decompression exception short algorithm id of nn"}, - */ - {0x7100, "Decompression exception long algorithm id"}, - - {0x7200, "Session fixation error"}, - {0x7201, "Session fixation error writing lead-in"}, - {0x7202, "Session fixation error writing lead-out"}, - {0x7203, "Session fixation error - incomplete track in session"}, - {0x7204, "Empty or partially written reserved track"}, - {0x7205, "No more track reservations allowed"}, - {0x7206, "RMZ extension is not allowed"}, - {0x7207, "No more test zone extensions are allowed"}, - - {0x7300, "Cd control error"}, - {0x7301, "Power calibration area almost full"}, - {0x7302, "Power calibration area is full"}, - {0x7303, "Power calibration area error"}, - {0x7304, "Program memory area update failure"}, - {0x7305, "Program memory area is full"}, - {0x7306, "RMA/PMA is almost full"}, - {0x7310, "Current power calibration area almost full"}, - {0x7311, "Current power calibration area is full"}, - {0x7317, "RDZ is full"}, - - {0x7400, "Security error"}, - {0x7401, "Unable to decrypt data"}, - {0x7402, "Unencrypted data encountered while decrypting"}, - {0x7403, "Incorrect data encryption key"}, - {0x7404, "Cryptographic integrity validation failed"}, - {0x7405, "Error decrypting data"}, - {0x7406, "Unknown signature verification key"}, - {0x7407, "Encryption parameters not useable"}, - {0x7408, "Digital signature validation failure"}, - {0x7409, "Encryption mode mismatch on read"}, - {0x740A, "Encrypted block not raw read enabled"}, - {0x740B, "Incorrect Encryption parameters"}, - {0x740C, "Unable to decrypt parameter list"}, - {0x740D, "Encryption algorithm disabled"}, - {0x7410, "SA creation parameter value invalid"}, - {0x7411, "SA creation parameter value rejected"}, - {0x7412, "Invalid SA usage"}, - {0x7421, "Data Encryption configuration prevented"}, - {0x7430, "SA creation parameter not supported"}, - {0x7440, "Authentication failed"}, - {0x7461, "External data encryption key manager access error"}, - {0x7462, "External data encryption key manager error"}, - {0x7463, "External data encryption key not found"}, - {0x7464, "External data encryption request not authorized"}, - {0x746E, "External data encryption control timeout"}, - {0x746F, "External data encryption control error"}, - {0x7471, "Logical unit access not authorized"}, - {0x7479, "Security conflict in translated device"}, - +#define SENSE_CODE(c, s) {c, s}, +#include "sense_codes.h" +#undef SENSE_CODE {0, NULL} }; diff --git a/drivers/scsi/sense_codes.h b/drivers/scsi/sense_codes.h new file mode 100644 index 000000000000..e4e1dccd1f2f --- /dev/null +++ b/drivers/scsi/sense_codes.h @@ -0,0 +1,826 @@ +/* + * The canonical list of T10 Additional Sense Codes is available at: + * http://www.t10.org/lists/asc-num.txt [most recent: 20141221] + */ + +SENSE_CODE(0x0000, "No additional sense information") +SENSE_CODE(0x0001, "Filemark detected") +SENSE_CODE(0x0002, "End-of-partition/medium detected") +SENSE_CODE(0x0003, "Setmark detected") +SENSE_CODE(0x0004, "Beginning-of-partition/medium detected") +SENSE_CODE(0x0005, "End-of-data detected") +SENSE_CODE(0x0006, "I/O process terminated") +SENSE_CODE(0x0007, "Programmable early warning detected") +SENSE_CODE(0x0011, "Audio play operation in progress") +SENSE_CODE(0x0012, "Audio play operation paused") +SENSE_CODE(0x0013, "Audio play operation successfully completed") +SENSE_CODE(0x0014, "Audio play operation stopped due to error") +SENSE_CODE(0x0015, "No current audio status to return") +SENSE_CODE(0x0016, "Operation in progress") +SENSE_CODE(0x0017, "Cleaning requested") +SENSE_CODE(0x0018, "Erase operation in progress") +SENSE_CODE(0x0019, "Locate operation in progress") +SENSE_CODE(0x001A, "Rewind operation in progress") +SENSE_CODE(0x001B, "Set capacity operation in progress") +SENSE_CODE(0x001C, "Verify operation in progress") +SENSE_CODE(0x001D, "ATA pass through information available") +SENSE_CODE(0x001E, "Conflicting SA creation request") +SENSE_CODE(0x001F, "Logical unit transitioning to another power condition") +SENSE_CODE(0x0020, "Extended copy information available") +SENSE_CODE(0x0021, "Atomic command aborted due to ACA") + +SENSE_CODE(0x0100, "No index/sector signal") + +SENSE_CODE(0x0200, "No seek complete") + +SENSE_CODE(0x0300, "Peripheral device write fault") +SENSE_CODE(0x0301, "No write current") +SENSE_CODE(0x0302, "Excessive write errors") + +SENSE_CODE(0x0400, "Logical unit not ready, cause not reportable") +SENSE_CODE(0x0401, "Logical unit is in process of becoming ready") +SENSE_CODE(0x0402, "Logical unit not ready, initializing command required") +SENSE_CODE(0x0403, "Logical unit not ready, manual intervention required") +SENSE_CODE(0x0404, "Logical unit not ready, format in progress") +SENSE_CODE(0x0405, "Logical unit not ready, rebuild in progress") +SENSE_CODE(0x0406, "Logical unit not ready, recalculation in progress") +SENSE_CODE(0x0407, "Logical unit not ready, operation in progress") +SENSE_CODE(0x0408, "Logical unit not ready, long write in progress") +SENSE_CODE(0x0409, "Logical unit not ready, self-test in progress") +SENSE_CODE(0x040A, "Logical unit not accessible, asymmetric access state transition") +SENSE_CODE(0x040B, "Logical unit not accessible, target port in standby state") +SENSE_CODE(0x040C, "Logical unit not accessible, target port in unavailable state") +SENSE_CODE(0x040D, "Logical unit not ready, structure check required") +SENSE_CODE(0x040E, "Logical unit not ready, security session in progress") +SENSE_CODE(0x0410, "Logical unit not ready, auxiliary memory not accessible") +SENSE_CODE(0x0411, "Logical unit not ready, notify (enable spinup) required") +SENSE_CODE(0x0412, "Logical unit not ready, offline") +SENSE_CODE(0x0413, "Logical unit not ready, SA creation in progress") +SENSE_CODE(0x0414, "Logical unit not ready, space allocation in progress") +SENSE_CODE(0x0415, "Logical unit not ready, robotics disabled") +SENSE_CODE(0x0416, "Logical unit not ready, configuration required") +SENSE_CODE(0x0417, "Logical unit not ready, calibration required") +SENSE_CODE(0x0418, "Logical unit not ready, a door is open") +SENSE_CODE(0x0419, "Logical unit not ready, operating in sequential mode") +SENSE_CODE(0x041A, "Logical unit not ready, start stop unit command in progress") +SENSE_CODE(0x041B, "Logical unit not ready, sanitize in progress") +SENSE_CODE(0x041C, "Logical unit not ready, additional power use not yet granted") +SENSE_CODE(0x041D, "Logical unit not ready, configuration in progress") +SENSE_CODE(0x041E, "Logical unit not ready, microcode activation required") +SENSE_CODE(0x041F, "Logical unit not ready, microcode download required") +SENSE_CODE(0x0420, "Logical unit not ready, logical unit reset required") +SENSE_CODE(0x0421, "Logical unit not ready, hard reset required") +SENSE_CODE(0x0422, "Logical unit not ready, power cycle required") + +SENSE_CODE(0x0500, "Logical unit does not respond to selection") + +SENSE_CODE(0x0600, "No reference position found") + +SENSE_CODE(0x0700, "Multiple peripheral devices selected") + +SENSE_CODE(0x0800, "Logical unit communication failure") +SENSE_CODE(0x0801, "Logical unit communication time-out") +SENSE_CODE(0x0802, "Logical unit communication parity error") +SENSE_CODE(0x0803, "Logical unit communication CRC error (Ultra-DMA/32)") +SENSE_CODE(0x0804, "Unreachable copy target") + +SENSE_CODE(0x0900, "Track following error") +SENSE_CODE(0x0901, "Tracking servo failure") +SENSE_CODE(0x0902, "Focus servo failure") +SENSE_CODE(0x0903, "Spindle servo failure") +SENSE_CODE(0x0904, "Head select fault") +SENSE_CODE(0x0905, "Vibration induced tracking error") + +SENSE_CODE(0x0A00, "Error log overflow") + +SENSE_CODE(0x0B00, "Warning") +SENSE_CODE(0x0B01, "Warning - specified temperature exceeded") +SENSE_CODE(0x0B02, "Warning - enclosure degraded") +SENSE_CODE(0x0B03, "Warning - background self-test failed") +SENSE_CODE(0x0B04, "Warning - background pre-scan detected medium error") +SENSE_CODE(0x0B05, "Warning - background medium scan detected medium error") +SENSE_CODE(0x0B06, "Warning - non-volatile cache now volatile") +SENSE_CODE(0x0B07, "Warning - degraded power to non-volatile cache") +SENSE_CODE(0x0B08, "Warning - power loss expected") +SENSE_CODE(0x0B09, "Warning - device statistics notification active") + +SENSE_CODE(0x0C00, "Write error") +SENSE_CODE(0x0C01, "Write error - recovered with auto reallocation") +SENSE_CODE(0x0C02, "Write error - auto reallocation failed") +SENSE_CODE(0x0C03, "Write error - recommend reassignment") +SENSE_CODE(0x0C04, "Compression check miscompare error") +SENSE_CODE(0x0C05, "Data expansion occurred during compression") +SENSE_CODE(0x0C06, "Block not compressible") +SENSE_CODE(0x0C07, "Write error - recovery needed") +SENSE_CODE(0x0C08, "Write error - recovery failed") +SENSE_CODE(0x0C09, "Write error - loss of streaming") +SENSE_CODE(0x0C0A, "Write error - padding blocks added") +SENSE_CODE(0x0C0B, "Auxiliary memory write error") +SENSE_CODE(0x0C0C, "Write error - unexpected unsolicited data") +SENSE_CODE(0x0C0D, "Write error - not enough unsolicited data") +SENSE_CODE(0x0C0E, "Multiple write errors") +SENSE_CODE(0x0C0F, "Defects in error window") +SENSE_CODE(0x0C10, "Incomplete multiple atomic write operations") + +SENSE_CODE(0x0D00, "Error detected by third party temporary initiator") +SENSE_CODE(0x0D01, "Third party device failure") +SENSE_CODE(0x0D02, "Copy target device not reachable") +SENSE_CODE(0x0D03, "Incorrect copy target device type") +SENSE_CODE(0x0D04, "Copy target device data underrun") +SENSE_CODE(0x0D05, "Copy target device data overrun") + +SENSE_CODE(0x0E00, "Invalid information unit") +SENSE_CODE(0x0E01, "Information unit too short") +SENSE_CODE(0x0E02, "Information unit too long") +SENSE_CODE(0x0E03, "Invalid field in command information unit") + +SENSE_CODE(0x1000, "Id CRC or ECC error") +SENSE_CODE(0x1001, "Logical block guard check failed") +SENSE_CODE(0x1002, "Logical block application tag check failed") +SENSE_CODE(0x1003, "Logical block reference tag check failed") +SENSE_CODE(0x1004, "Logical block protection error on recover buffered data") +SENSE_CODE(0x1005, "Logical block protection method error") + +SENSE_CODE(0x1100, "Unrecovered read error") +SENSE_CODE(0x1101, "Read retries exhausted") +SENSE_CODE(0x1102, "Error too long to correct") +SENSE_CODE(0x1103, "Multiple read errors") +SENSE_CODE(0x1104, "Unrecovered read error - auto reallocate failed") +SENSE_CODE(0x1105, "L-EC uncorrectable error") +SENSE_CODE(0x1106, "CIRC unrecovered error") +SENSE_CODE(0x1107, "Data re-synchronization error") +SENSE_CODE(0x1108, "Incomplete block read") +SENSE_CODE(0x1109, "No gap found") +SENSE_CODE(0x110A, "Miscorrected error") +SENSE_CODE(0x110B, "Unrecovered read error - recommend reassignment") +SENSE_CODE(0x110C, "Unrecovered read error - recommend rewrite the data") +SENSE_CODE(0x110D, "De-compression CRC error") +SENSE_CODE(0x110E, "Cannot decompress using declared algorithm") +SENSE_CODE(0x110F, "Error reading UPC/EAN number") +SENSE_CODE(0x1110, "Error reading ISRC number") +SENSE_CODE(0x1111, "Read error - loss of streaming") +SENSE_CODE(0x1112, "Auxiliary memory read error") +SENSE_CODE(0x1113, "Read error - failed retransmission request") +SENSE_CODE(0x1114, "Read error - lba marked bad by application client") +SENSE_CODE(0x1115, "Write after sanitize required") + +SENSE_CODE(0x1200, "Address mark not found for id field") + +SENSE_CODE(0x1300, "Address mark not found for data field") + +SENSE_CODE(0x1400, "Recorded entity not found") +SENSE_CODE(0x1401, "Record not found") +SENSE_CODE(0x1402, "Filemark or setmark not found") +SENSE_CODE(0x1403, "End-of-data not found") +SENSE_CODE(0x1404, "Block sequence error") +SENSE_CODE(0x1405, "Record not found - recommend reassignment") +SENSE_CODE(0x1406, "Record not found - data auto-reallocated") +SENSE_CODE(0x1407, "Locate operation failure") + +SENSE_CODE(0x1500, "Random positioning error") +SENSE_CODE(0x1501, "Mechanical positioning error") +SENSE_CODE(0x1502, "Positioning error detected by read of medium") + +SENSE_CODE(0x1600, "Data synchronization mark error") +SENSE_CODE(0x1601, "Data sync error - data rewritten") +SENSE_CODE(0x1602, "Data sync error - recommend rewrite") +SENSE_CODE(0x1603, "Data sync error - data auto-reallocated") +SENSE_CODE(0x1604, "Data sync error - recommend reassignment") + +SENSE_CODE(0x1700, "Recovered data with no error correction applied") +SENSE_CODE(0x1701, "Recovered data with retries") +SENSE_CODE(0x1702, "Recovered data with positive head offset") +SENSE_CODE(0x1703, "Recovered data with negative head offset") +SENSE_CODE(0x1704, "Recovered data with retries and/or circ applied") +SENSE_CODE(0x1705, "Recovered data using previous sector id") +SENSE_CODE(0x1706, "Recovered data without ECC - data auto-reallocated") +SENSE_CODE(0x1707, "Recovered data without ECC - recommend reassignment") +SENSE_CODE(0x1708, "Recovered data without ECC - recommend rewrite") +SENSE_CODE(0x1709, "Recovered data without ECC - data rewritten") + +SENSE_CODE(0x1800, "Recovered data with error correction applied") +SENSE_CODE(0x1801, "Recovered data with error corr. & retries applied") +SENSE_CODE(0x1802, "Recovered data - data auto-reallocated") +SENSE_CODE(0x1803, "Recovered data with CIRC") +SENSE_CODE(0x1804, "Recovered data with L-EC") +SENSE_CODE(0x1805, "Recovered data - recommend reassignment") +SENSE_CODE(0x1806, "Recovered data - recommend rewrite") +SENSE_CODE(0x1807, "Recovered data with ECC - data rewritten") +SENSE_CODE(0x1808, "Recovered data with linking") + +SENSE_CODE(0x1900, "Defect list error") +SENSE_CODE(0x1901, "Defect list not available") +SENSE_CODE(0x1902, "Defect list error in primary list") +SENSE_CODE(0x1903, "Defect list error in grown list") + +SENSE_CODE(0x1A00, "Parameter list length error") + +SENSE_CODE(0x1B00, "Synchronous data transfer error") + +SENSE_CODE(0x1C00, "Defect list not found") +SENSE_CODE(0x1C01, "Primary defect list not found") +SENSE_CODE(0x1C02, "Grown defect list not found") + +SENSE_CODE(0x1D00, "Miscompare during verify operation") +SENSE_CODE(0x1D01, "Miscompare verify of unmapped LBA") + +SENSE_CODE(0x1E00, "Recovered id with ECC correction") + +SENSE_CODE(0x1F00, "Partial defect list transfer") + +SENSE_CODE(0x2000, "Invalid command operation code") +SENSE_CODE(0x2001, "Access denied - initiator pending-enrolled") +SENSE_CODE(0x2002, "Access denied - no access rights") +SENSE_CODE(0x2003, "Access denied - invalid mgmt id key") +SENSE_CODE(0x2004, "Illegal command while in write capable state") +SENSE_CODE(0x2005, "Obsolete") +SENSE_CODE(0x2006, "Illegal command while in explicit address mode") +SENSE_CODE(0x2007, "Illegal command while in implicit address mode") +SENSE_CODE(0x2008, "Access denied - enrollment conflict") +SENSE_CODE(0x2009, "Access denied - invalid LU identifier") +SENSE_CODE(0x200A, "Access denied - invalid proxy token") +SENSE_CODE(0x200B, "Access denied - ACL LUN conflict") +SENSE_CODE(0x200C, "Illegal command when not in append-only mode") + +SENSE_CODE(0x2100, "Logical block address out of range") +SENSE_CODE(0x2101, "Invalid element address") +SENSE_CODE(0x2102, "Invalid address for write") +SENSE_CODE(0x2103, "Invalid write crossing layer jump") +SENSE_CODE(0x2104, "Unaligned write command") +SENSE_CODE(0x2105, "Write boundary violation") +SENSE_CODE(0x2106, "Attempt to read invalid data") +SENSE_CODE(0x2107, "Read boundary violation") + +SENSE_CODE(0x2200, "Illegal function (use 20 00, 24 00, or 26 00)") + +SENSE_CODE(0x2300, "Invalid token operation, cause not reportable") +SENSE_CODE(0x2301, "Invalid token operation, unsupported token type") +SENSE_CODE(0x2302, "Invalid token operation, remote token usage not supported") +SENSE_CODE(0x2303, "Invalid token operation, remote rod token creation not supported") +SENSE_CODE(0x2304, "Invalid token operation, token unknown") +SENSE_CODE(0x2305, "Invalid token operation, token corrupt") +SENSE_CODE(0x2306, "Invalid token operation, token revoked") +SENSE_CODE(0x2307, "Invalid token operation, token expired") +SENSE_CODE(0x2308, "Invalid token operation, token cancelled") +SENSE_CODE(0x2309, "Invalid token operation, token deleted") +SENSE_CODE(0x230A, "Invalid token operation, invalid token length") + +SENSE_CODE(0x2400, "Invalid field in cdb") +SENSE_CODE(0x2401, "CDB decryption error") +SENSE_CODE(0x2402, "Obsolete") +SENSE_CODE(0x2403, "Obsolete") +SENSE_CODE(0x2404, "Security audit value frozen") +SENSE_CODE(0x2405, "Security working key frozen") +SENSE_CODE(0x2406, "Nonce not unique") +SENSE_CODE(0x2407, "Nonce timestamp out of range") +SENSE_CODE(0x2408, "Invalid XCDB") + +SENSE_CODE(0x2500, "Logical unit not supported") + +SENSE_CODE(0x2600, "Invalid field in parameter list") +SENSE_CODE(0x2601, "Parameter not supported") +SENSE_CODE(0x2602, "Parameter value invalid") +SENSE_CODE(0x2603, "Threshold parameters not supported") +SENSE_CODE(0x2604, "Invalid release of persistent reservation") +SENSE_CODE(0x2605, "Data decryption error") +SENSE_CODE(0x2606, "Too many target descriptors") +SENSE_CODE(0x2607, "Unsupported target descriptor type code") +SENSE_CODE(0x2608, "Too many segment descriptors") +SENSE_CODE(0x2609, "Unsupported segment descriptor type code") +SENSE_CODE(0x260A, "Unexpected inexact segment") +SENSE_CODE(0x260B, "Inline data length exceeded") +SENSE_CODE(0x260C, "Invalid operation for copy source or destination") +SENSE_CODE(0x260D, "Copy segment granularity violation") +SENSE_CODE(0x260E, "Invalid parameter while port is enabled") +SENSE_CODE(0x260F, "Invalid data-out buffer integrity check value") +SENSE_CODE(0x2610, "Data decryption key fail limit reached") +SENSE_CODE(0x2611, "Incomplete key-associated data set") +SENSE_CODE(0x2612, "Vendor specific key reference not found") + +SENSE_CODE(0x2700, "Write protected") +SENSE_CODE(0x2701, "Hardware write protected") +SENSE_CODE(0x2702, "Logical unit software write protected") +SENSE_CODE(0x2703, "Associated write protect") +SENSE_CODE(0x2704, "Persistent write protect") +SENSE_CODE(0x2705, "Permanent write protect") +SENSE_CODE(0x2706, "Conditional write protect") +SENSE_CODE(0x2707, "Space allocation failed write protect") +SENSE_CODE(0x2708, "Zone is read only") + +SENSE_CODE(0x2800, "Not ready to ready change, medium may have changed") +SENSE_CODE(0x2801, "Import or export element accessed") +SENSE_CODE(0x2802, "Format-layer may have changed") +SENSE_CODE(0x2803, "Import/export element accessed, medium changed") + +SENSE_CODE(0x2900, "Power on, reset, or bus device reset occurred") +SENSE_CODE(0x2901, "Power on occurred") +SENSE_CODE(0x2902, "Scsi bus reset occurred") +SENSE_CODE(0x2903, "Bus device reset function occurred") +SENSE_CODE(0x2904, "Device internal reset") +SENSE_CODE(0x2905, "Transceiver mode changed to single-ended") +SENSE_CODE(0x2906, "Transceiver mode changed to lvd") +SENSE_CODE(0x2907, "I_T nexus loss occurred") + +SENSE_CODE(0x2A00, "Parameters changed") +SENSE_CODE(0x2A01, "Mode parameters changed") +SENSE_CODE(0x2A02, "Log parameters changed") +SENSE_CODE(0x2A03, "Reservations preempted") +SENSE_CODE(0x2A04, "Reservations released") +SENSE_CODE(0x2A05, "Registrations preempted") +SENSE_CODE(0x2A06, "Asymmetric access state changed") +SENSE_CODE(0x2A07, "Implicit asymmetric access state transition failed") +SENSE_CODE(0x2A08, "Priority changed") +SENSE_CODE(0x2A09, "Capacity data has changed") +SENSE_CODE(0x2A0A, "Error history I_T nexus cleared") +SENSE_CODE(0x2A0B, "Error history snapshot released") +SENSE_CODE(0x2A0C, "Error recovery attributes have changed") +SENSE_CODE(0x2A0D, "Data encryption capabilities changed") +SENSE_CODE(0x2A10, "Timestamp changed") +SENSE_CODE(0x2A11, "Data encryption parameters changed by another i_t nexus") +SENSE_CODE(0x2A12, "Data encryption parameters changed by vendor specific event") +SENSE_CODE(0x2A13, "Data encryption key instance counter has changed") +SENSE_CODE(0x2A14, "SA creation capabilities data has changed") +SENSE_CODE(0x2A15, "Medium removal prevention preempted") + +SENSE_CODE(0x2B00, "Copy cannot execute since host cannot disconnect") + +SENSE_CODE(0x2C00, "Command sequence error") +SENSE_CODE(0x2C01, "Too many windows specified") +SENSE_CODE(0x2C02, "Invalid combination of windows specified") +SENSE_CODE(0x2C03, "Current program area is not empty") +SENSE_CODE(0x2C04, "Current program area is empty") +SENSE_CODE(0x2C05, "Illegal power condition request") +SENSE_CODE(0x2C06, "Persistent prevent conflict") +SENSE_CODE(0x2C07, "Previous busy status") +SENSE_CODE(0x2C08, "Previous task set full status") +SENSE_CODE(0x2C09, "Previous reservation conflict status") +SENSE_CODE(0x2C0A, "Partition or collection contains user objects") +SENSE_CODE(0x2C0B, "Not reserved") +SENSE_CODE(0x2C0C, "Orwrite generation does not match") +SENSE_CODE(0x2C0D, "Reset write pointer not allowed") +SENSE_CODE(0x2C0E, "Zone is offline") + +SENSE_CODE(0x2D00, "Overwrite error on update in place") + +SENSE_CODE(0x2E00, "Insufficient time for operation") +SENSE_CODE(0x2E01, "Command timeout before processing") +SENSE_CODE(0x2E02, "Command timeout during processing") +SENSE_CODE(0x2E03, "Command timeout during processing due to error recovery") + +SENSE_CODE(0x2F00, "Commands cleared by another initiator") +SENSE_CODE(0x2F01, "Commands cleared by power loss notification") +SENSE_CODE(0x2F02, "Commands cleared by device server") +SENSE_CODE(0x2F03, "Some commands cleared by queuing layer event") + +SENSE_CODE(0x3000, "Incompatible medium installed") +SENSE_CODE(0x3001, "Cannot read medium - unknown format") +SENSE_CODE(0x3002, "Cannot read medium - incompatible format") +SENSE_CODE(0x3003, "Cleaning cartridge installed") +SENSE_CODE(0x3004, "Cannot write medium - unknown format") +SENSE_CODE(0x3005, "Cannot write medium - incompatible format") +SENSE_CODE(0x3006, "Cannot format medium - incompatible medium") +SENSE_CODE(0x3007, "Cleaning failure") +SENSE_CODE(0x3008, "Cannot write - application code mismatch") +SENSE_CODE(0x3009, "Current session not fixated for append") +SENSE_CODE(0x300A, "Cleaning request rejected") +SENSE_CODE(0x300C, "WORM medium - overwrite attempted") +SENSE_CODE(0x300D, "WORM medium - integrity check") +SENSE_CODE(0x3010, "Medium not formatted") +SENSE_CODE(0x3011, "Incompatible volume type") +SENSE_CODE(0x3012, "Incompatible volume qualifier") +SENSE_CODE(0x3013, "Cleaning volume expired") + +SENSE_CODE(0x3100, "Medium format corrupted") +SENSE_CODE(0x3101, "Format command failed") +SENSE_CODE(0x3102, "Zoned formatting failed due to spare linking") +SENSE_CODE(0x3103, "Sanitize command failed") + +SENSE_CODE(0x3200, "No defect spare location available") +SENSE_CODE(0x3201, "Defect list update failure") + +SENSE_CODE(0x3300, "Tape length error") + +SENSE_CODE(0x3400, "Enclosure failure") + +SENSE_CODE(0x3500, "Enclosure services failure") +SENSE_CODE(0x3501, "Unsupported enclosure function") +SENSE_CODE(0x3502, "Enclosure services unavailable") +SENSE_CODE(0x3503, "Enclosure services transfer failure") +SENSE_CODE(0x3504, "Enclosure services transfer refused") +SENSE_CODE(0x3505, "Enclosure services checksum error") + +SENSE_CODE(0x3600, "Ribbon, ink, or toner failure") + +SENSE_CODE(0x3700, "Rounded parameter") + +SENSE_CODE(0x3800, "Event status notification") +SENSE_CODE(0x3802, "Esn - power management class event") +SENSE_CODE(0x3804, "Esn - media class event") +SENSE_CODE(0x3806, "Esn - device busy class event") +SENSE_CODE(0x3807, "Thin Provisioning soft threshold reached") + +SENSE_CODE(0x3900, "Saving parameters not supported") + +SENSE_CODE(0x3A00, "Medium not present") +SENSE_CODE(0x3A01, "Medium not present - tray closed") +SENSE_CODE(0x3A02, "Medium not present - tray open") +SENSE_CODE(0x3A03, "Medium not present - loadable") +SENSE_CODE(0x3A04, "Medium not present - medium auxiliary memory accessible") + +SENSE_CODE(0x3B00, "Sequential positioning error") +SENSE_CODE(0x3B01, "Tape position error at beginning-of-medium") +SENSE_CODE(0x3B02, "Tape position error at end-of-medium") +SENSE_CODE(0x3B03, "Tape or electronic vertical forms unit not ready") +SENSE_CODE(0x3B04, "Slew failure") +SENSE_CODE(0x3B05, "Paper jam") +SENSE_CODE(0x3B06, "Failed to sense top-of-form") +SENSE_CODE(0x3B07, "Failed to sense bottom-of-form") +SENSE_CODE(0x3B08, "Reposition error") +SENSE_CODE(0x3B09, "Read past end of medium") +SENSE_CODE(0x3B0A, "Read past beginning of medium") +SENSE_CODE(0x3B0B, "Position past end of medium") +SENSE_CODE(0x3B0C, "Position past beginning of medium") +SENSE_CODE(0x3B0D, "Medium destination element full") +SENSE_CODE(0x3B0E, "Medium source element empty") +SENSE_CODE(0x3B0F, "End of medium reached") +SENSE_CODE(0x3B11, "Medium magazine not accessible") +SENSE_CODE(0x3B12, "Medium magazine removed") +SENSE_CODE(0x3B13, "Medium magazine inserted") +SENSE_CODE(0x3B14, "Medium magazine locked") +SENSE_CODE(0x3B15, "Medium magazine unlocked") +SENSE_CODE(0x3B16, "Mechanical positioning or changer error") +SENSE_CODE(0x3B17, "Read past end of user object") +SENSE_CODE(0x3B18, "Element disabled") +SENSE_CODE(0x3B19, "Element enabled") +SENSE_CODE(0x3B1A, "Data transfer device removed") +SENSE_CODE(0x3B1B, "Data transfer device inserted") +SENSE_CODE(0x3B1C, "Too many logical objects on partition to support operation") + +SENSE_CODE(0x3D00, "Invalid bits in identify message") + +SENSE_CODE(0x3E00, "Logical unit has not self-configured yet") +SENSE_CODE(0x3E01, "Logical unit failure") +SENSE_CODE(0x3E02, "Timeout on logical unit") +SENSE_CODE(0x3E03, "Logical unit failed self-test") +SENSE_CODE(0x3E04, "Logical unit unable to update self-test log") + +SENSE_CODE(0x3F00, "Target operating conditions have changed") +SENSE_CODE(0x3F01, "Microcode has been changed") +SENSE_CODE(0x3F02, "Changed operating definition") +SENSE_CODE(0x3F03, "Inquiry data has changed") +SENSE_CODE(0x3F04, "Component device attached") +SENSE_CODE(0x3F05, "Device identifier changed") +SENSE_CODE(0x3F06, "Redundancy group created or modified") +SENSE_CODE(0x3F07, "Redundancy group deleted") +SENSE_CODE(0x3F08, "Spare created or modified") +SENSE_CODE(0x3F09, "Spare deleted") +SENSE_CODE(0x3F0A, "Volume set created or modified") +SENSE_CODE(0x3F0B, "Volume set deleted") +SENSE_CODE(0x3F0C, "Volume set deassigned") +SENSE_CODE(0x3F0D, "Volume set reassigned") +SENSE_CODE(0x3F0E, "Reported luns data has changed") +SENSE_CODE(0x3F0F, "Echo buffer overwritten") +SENSE_CODE(0x3F10, "Medium loadable") +SENSE_CODE(0x3F11, "Medium auxiliary memory accessible") +SENSE_CODE(0x3F12, "iSCSI IP address added") +SENSE_CODE(0x3F13, "iSCSI IP address removed") +SENSE_CODE(0x3F14, "iSCSI IP address changed") +SENSE_CODE(0x3F15, "Inspect referrals sense descriptors") +SENSE_CODE(0x3F16, "Microcode has been changed without reset") +/* + * SENSE_CODE(0x40NN, "Ram failure") + * SENSE_CODE(0x40NN, "Diagnostic failure on component nn") + * SENSE_CODE(0x41NN, "Data path failure") + * SENSE_CODE(0x42NN, "Power-on or self-test failure") + */ +SENSE_CODE(0x4300, "Message error") + +SENSE_CODE(0x4400, "Internal target failure") +SENSE_CODE(0x4401, "Persistent reservation information lost") +SENSE_CODE(0x4471, "ATA device failed set features") + +SENSE_CODE(0x4500, "Select or reselect failure") + +SENSE_CODE(0x4600, "Unsuccessful soft reset") + +SENSE_CODE(0x4700, "Scsi parity error") +SENSE_CODE(0x4701, "Data phase CRC error detected") +SENSE_CODE(0x4702, "Scsi parity error detected during st data phase") +SENSE_CODE(0x4703, "Information unit iuCRC error detected") +SENSE_CODE(0x4704, "Asynchronous information protection error detected") +SENSE_CODE(0x4705, "Protocol service CRC error") +SENSE_CODE(0x4706, "Phy test function in progress") +SENSE_CODE(0x477f, "Some commands cleared by iSCSI Protocol event") + +SENSE_CODE(0x4800, "Initiator detected error message received") + +SENSE_CODE(0x4900, "Invalid message error") + +SENSE_CODE(0x4A00, "Command phase error") + +SENSE_CODE(0x4B00, "Data phase error") +SENSE_CODE(0x4B01, "Invalid target port transfer tag received") +SENSE_CODE(0x4B02, "Too much write data") +SENSE_CODE(0x4B03, "Ack/nak timeout") +SENSE_CODE(0x4B04, "Nak received") +SENSE_CODE(0x4B05, "Data offset error") +SENSE_CODE(0x4B06, "Initiator response timeout") +SENSE_CODE(0x4B07, "Connection lost") +SENSE_CODE(0x4B08, "Data-in buffer overflow - data buffer size") +SENSE_CODE(0x4B09, "Data-in buffer overflow - data buffer descriptor area") +SENSE_CODE(0x4B0A, "Data-in buffer error") +SENSE_CODE(0x4B0B, "Data-out buffer overflow - data buffer size") +SENSE_CODE(0x4B0C, "Data-out buffer overflow - data buffer descriptor area") +SENSE_CODE(0x4B0D, "Data-out buffer error") +SENSE_CODE(0x4B0E, "PCIe fabric error") +SENSE_CODE(0x4B0F, "PCIe completion timeout") +SENSE_CODE(0x4B10, "PCIe completer abort") +SENSE_CODE(0x4B11, "PCIe poisoned tlp received") +SENSE_CODE(0x4B12, "PCIe eCRC check failed") +SENSE_CODE(0x4B13, "PCIe unsupported request") +SENSE_CODE(0x4B14, "PCIe acs violation") +SENSE_CODE(0x4B15, "PCIe tlp prefix blocked") + +SENSE_CODE(0x4C00, "Logical unit failed self-configuration") +/* + * SENSE_CODE(0x4DNN, "Tagged overlapped commands (nn = queue tag)") + */ +SENSE_CODE(0x4E00, "Overlapped commands attempted") + +SENSE_CODE(0x5000, "Write append error") +SENSE_CODE(0x5001, "Write append position error") +SENSE_CODE(0x5002, "Position error related to timing") + +SENSE_CODE(0x5100, "Erase failure") +SENSE_CODE(0x5101, "Erase failure - incomplete erase operation detected") + +SENSE_CODE(0x5200, "Cartridge fault") + +SENSE_CODE(0x5300, "Media load or eject failed") +SENSE_CODE(0x5301, "Unload tape failure") +SENSE_CODE(0x5302, "Medium removal prevented") +SENSE_CODE(0x5303, "Medium removal prevented by data transfer element") +SENSE_CODE(0x5304, "Medium thread or unthread failure") +SENSE_CODE(0x5305, "Volume identifier invalid") +SENSE_CODE(0x5306, "Volume identifier missing") +SENSE_CODE(0x5307, "Duplicate volume identifier") +SENSE_CODE(0x5308, "Element status unknown") +SENSE_CODE(0x5309, "Data transfer device error - load failed") +SENSE_CODE(0x530a, "Data transfer device error - unload failed") +SENSE_CODE(0x530b, "Data transfer device error - unload missing") +SENSE_CODE(0x530c, "Data transfer device error - eject failed") +SENSE_CODE(0x530d, "Data transfer device error - library communication failed") + +SENSE_CODE(0x5400, "Scsi to host system interface failure") + +SENSE_CODE(0x5500, "System resource failure") +SENSE_CODE(0x5501, "System buffer full") +SENSE_CODE(0x5502, "Insufficient reservation resources") +SENSE_CODE(0x5503, "Insufficient resources") +SENSE_CODE(0x5504, "Insufficient registration resources") +SENSE_CODE(0x5505, "Insufficient access control resources") +SENSE_CODE(0x5506, "Auxiliary memory out of space") +SENSE_CODE(0x5507, "Quota error") +SENSE_CODE(0x5508, "Maximum number of supplemental decryption keys exceeded") +SENSE_CODE(0x5509, "Medium auxiliary memory not accessible") +SENSE_CODE(0x550A, "Data currently unavailable") +SENSE_CODE(0x550B, "Insufficient power for operation") +SENSE_CODE(0x550C, "Insufficient resources to create rod") +SENSE_CODE(0x550D, "Insufficient resources to create rod token") +SENSE_CODE(0x550E, "Insufficient zone resources") + +SENSE_CODE(0x5700, "Unable to recover table-of-contents") + +SENSE_CODE(0x5800, "Generation does not exist") + +SENSE_CODE(0x5900, "Updated block read") + +SENSE_CODE(0x5A00, "Operator request or state change input") +SENSE_CODE(0x5A01, "Operator medium removal request") +SENSE_CODE(0x5A02, "Operator selected write protect") +SENSE_CODE(0x5A03, "Operator selected write permit") + +SENSE_CODE(0x5B00, "Log exception") +SENSE_CODE(0x5B01, "Threshold condition met") +SENSE_CODE(0x5B02, "Log counter at maximum") +SENSE_CODE(0x5B03, "Log list codes exhausted") + +SENSE_CODE(0x5C00, "Rpl status change") +SENSE_CODE(0x5C01, "Spindles synchronized") +SENSE_CODE(0x5C02, "Spindles not synchronized") + +SENSE_CODE(0x5D00, "Failure prediction threshold exceeded") +SENSE_CODE(0x5D01, "Media failure prediction threshold exceeded") +SENSE_CODE(0x5D02, "Logical unit failure prediction threshold exceeded") +SENSE_CODE(0x5D03, "Spare area exhaustion prediction threshold exceeded") +SENSE_CODE(0x5D10, "Hardware impending failure general hard drive failure") +SENSE_CODE(0x5D11, "Hardware impending failure drive error rate too high") +SENSE_CODE(0x5D12, "Hardware impending failure data error rate too high") +SENSE_CODE(0x5D13, "Hardware impending failure seek error rate too high") +SENSE_CODE(0x5D14, "Hardware impending failure too many block reassigns") +SENSE_CODE(0x5D15, "Hardware impending failure access times too high") +SENSE_CODE(0x5D16, "Hardware impending failure start unit times too high") +SENSE_CODE(0x5D17, "Hardware impending failure channel parametrics") +SENSE_CODE(0x5D18, "Hardware impending failure controller detected") +SENSE_CODE(0x5D19, "Hardware impending failure throughput performance") +SENSE_CODE(0x5D1A, "Hardware impending failure seek time performance") +SENSE_CODE(0x5D1B, "Hardware impending failure spin-up retry count") +SENSE_CODE(0x5D1C, "Hardware impending failure drive calibration retry count") +SENSE_CODE(0x5D20, "Controller impending failure general hard drive failure") +SENSE_CODE(0x5D21, "Controller impending failure drive error rate too high") +SENSE_CODE(0x5D22, "Controller impending failure data error rate too high") +SENSE_CODE(0x5D23, "Controller impending failure seek error rate too high") +SENSE_CODE(0x5D24, "Controller impending failure too many block reassigns") +SENSE_CODE(0x5D25, "Controller impending failure access times too high") +SENSE_CODE(0x5D26, "Controller impending failure start unit times too high") +SENSE_CODE(0x5D27, "Controller impending failure channel parametrics") +SENSE_CODE(0x5D28, "Controller impending failure controller detected") +SENSE_CODE(0x5D29, "Controller impending failure throughput performance") +SENSE_CODE(0x5D2A, "Controller impending failure seek time performance") +SENSE_CODE(0x5D2B, "Controller impending failure spin-up retry count") +SENSE_CODE(0x5D2C, "Controller impending failure drive calibration retry count") +SENSE_CODE(0x5D30, "Data channel impending failure general hard drive failure") +SENSE_CODE(0x5D31, "Data channel impending failure drive error rate too high") +SENSE_CODE(0x5D32, "Data channel impending failure data error rate too high") +SENSE_CODE(0x5D33, "Data channel impending failure seek error rate too high") +SENSE_CODE(0x5D34, "Data channel impending failure too many block reassigns") +SENSE_CODE(0x5D35, "Data channel impending failure access times too high") +SENSE_CODE(0x5D36, "Data channel impending failure start unit times too high") +SENSE_CODE(0x5D37, "Data channel impending failure channel parametrics") +SENSE_CODE(0x5D38, "Data channel impending failure controller detected") +SENSE_CODE(0x5D39, "Data channel impending failure throughput performance") +SENSE_CODE(0x5D3A, "Data channel impending failure seek time performance") +SENSE_CODE(0x5D3B, "Data channel impending failure spin-up retry count") +SENSE_CODE(0x5D3C, "Data channel impending failure drive calibration retry count") +SENSE_CODE(0x5D40, "Servo impending failure general hard drive failure") +SENSE_CODE(0x5D41, "Servo impending failure drive error rate too high") +SENSE_CODE(0x5D42, "Servo impending failure data error rate too high") +SENSE_CODE(0x5D43, "Servo impending failure seek error rate too high") +SENSE_CODE(0x5D44, "Servo impending failure too many block reassigns") +SENSE_CODE(0x5D45, "Servo impending failure access times too high") +SENSE_CODE(0x5D46, "Servo impending failure start unit times too high") +SENSE_CODE(0x5D47, "Servo impending failure channel parametrics") +SENSE_CODE(0x5D48, "Servo impending failure controller detected") +SENSE_CODE(0x5D49, "Servo impending failure throughput performance") +SENSE_CODE(0x5D4A, "Servo impending failure seek time performance") +SENSE_CODE(0x5D4B, "Servo impending failure spin-up retry count") +SENSE_CODE(0x5D4C, "Servo impending failure drive calibration retry count") +SENSE_CODE(0x5D50, "Spindle impending failure general hard drive failure") +SENSE_CODE(0x5D51, "Spindle impending failure drive error rate too high") +SENSE_CODE(0x5D52, "Spindle impending failure data error rate too high") +SENSE_CODE(0x5D53, "Spindle impending failure seek error rate too high") +SENSE_CODE(0x5D54, "Spindle impending failure too many block reassigns") +SENSE_CODE(0x5D55, "Spindle impending failure access times too high") +SENSE_CODE(0x5D56, "Spindle impending failure start unit times too high") +SENSE_CODE(0x5D57, "Spindle impending failure channel parametrics") +SENSE_CODE(0x5D58, "Spindle impending failure controller detected") +SENSE_CODE(0x5D59, "Spindle impending failure throughput performance") +SENSE_CODE(0x5D5A, "Spindle impending failure seek time performance") +SENSE_CODE(0x5D5B, "Spindle impending failure spin-up retry count") +SENSE_CODE(0x5D5C, "Spindle impending failure drive calibration retry count") +SENSE_CODE(0x5D60, "Firmware impending failure general hard drive failure") +SENSE_CODE(0x5D61, "Firmware impending failure drive error rate too high") +SENSE_CODE(0x5D62, "Firmware impending failure data error rate too high") +SENSE_CODE(0x5D63, "Firmware impending failure seek error rate too high") +SENSE_CODE(0x5D64, "Firmware impending failure too many block reassigns") +SENSE_CODE(0x5D65, "Firmware impending failure access times too high") +SENSE_CODE(0x5D66, "Firmware impending failure start unit times too high") +SENSE_CODE(0x5D67, "Firmware impending failure channel parametrics") +SENSE_CODE(0x5D68, "Firmware impending failure controller detected") +SENSE_CODE(0x5D69, "Firmware impending failure throughput performance") +SENSE_CODE(0x5D6A, "Firmware impending failure seek time performance") +SENSE_CODE(0x5D6B, "Firmware impending failure spin-up retry count") +SENSE_CODE(0x5D6C, "Firmware impending failure drive calibration retry count") +SENSE_CODE(0x5DFF, "Failure prediction threshold exceeded (false)") + +SENSE_CODE(0x5E00, "Low power condition on") +SENSE_CODE(0x5E01, "Idle condition activated by timer") +SENSE_CODE(0x5E02, "Standby condition activated by timer") +SENSE_CODE(0x5E03, "Idle condition activated by command") +SENSE_CODE(0x5E04, "Standby condition activated by command") +SENSE_CODE(0x5E05, "Idle_b condition activated by timer") +SENSE_CODE(0x5E06, "Idle_b condition activated by command") +SENSE_CODE(0x5E07, "Idle_c condition activated by timer") +SENSE_CODE(0x5E08, "Idle_c condition activated by command") +SENSE_CODE(0x5E09, "Standby_y condition activated by timer") +SENSE_CODE(0x5E0A, "Standby_y condition activated by command") +SENSE_CODE(0x5E41, "Power state change to active") +SENSE_CODE(0x5E42, "Power state change to idle") +SENSE_CODE(0x5E43, "Power state change to standby") +SENSE_CODE(0x5E45, "Power state change to sleep") +SENSE_CODE(0x5E47, "Power state change to device control") + +SENSE_CODE(0x6000, "Lamp failure") + +SENSE_CODE(0x6100, "Video acquisition error") +SENSE_CODE(0x6101, "Unable to acquire video") +SENSE_CODE(0x6102, "Out of focus") + +SENSE_CODE(0x6200, "Scan head positioning error") + +SENSE_CODE(0x6300, "End of user area encountered on this track") +SENSE_CODE(0x6301, "Packet does not fit in available space") + +SENSE_CODE(0x6400, "Illegal mode for this track") +SENSE_CODE(0x6401, "Invalid packet size") + +SENSE_CODE(0x6500, "Voltage fault") + +SENSE_CODE(0x6600, "Automatic document feeder cover up") +SENSE_CODE(0x6601, "Automatic document feeder lift up") +SENSE_CODE(0x6602, "Document jam in automatic document feeder") +SENSE_CODE(0x6603, "Document miss feed automatic in document feeder") + +SENSE_CODE(0x6700, "Configuration failure") +SENSE_CODE(0x6701, "Configuration of incapable logical units failed") +SENSE_CODE(0x6702, "Add logical unit failed") +SENSE_CODE(0x6703, "Modification of logical unit failed") +SENSE_CODE(0x6704, "Exchange of logical unit failed") +SENSE_CODE(0x6705, "Remove of logical unit failed") +SENSE_CODE(0x6706, "Attachment of logical unit failed") +SENSE_CODE(0x6707, "Creation of logical unit failed") +SENSE_CODE(0x6708, "Assign failure occurred") +SENSE_CODE(0x6709, "Multiply assigned logical unit") +SENSE_CODE(0x670A, "Set target port groups command failed") +SENSE_CODE(0x670B, "ATA device feature not enabled") + +SENSE_CODE(0x6800, "Logical unit not configured") +SENSE_CODE(0x6801, "Subsidiary logical unit not configured") + +SENSE_CODE(0x6900, "Data loss on logical unit") +SENSE_CODE(0x6901, "Multiple logical unit failures") +SENSE_CODE(0x6902, "Parity/data mismatch") + +SENSE_CODE(0x6A00, "Informational, refer to log") + +SENSE_CODE(0x6B00, "State change has occurred") +SENSE_CODE(0x6B01, "Redundancy level got better") +SENSE_CODE(0x6B02, "Redundancy level got worse") + +SENSE_CODE(0x6C00, "Rebuild failure occurred") + +SENSE_CODE(0x6D00, "Recalculate failure occurred") + +SENSE_CODE(0x6E00, "Command to logical unit failed") + +SENSE_CODE(0x6F00, "Copy protection key exchange failure - authentication failure") +SENSE_CODE(0x6F01, "Copy protection key exchange failure - key not present") +SENSE_CODE(0x6F02, "Copy protection key exchange failure - key not established") +SENSE_CODE(0x6F03, "Read of scrambled sector without authentication") +SENSE_CODE(0x6F04, "Media region code is mismatched to logical unit region") +SENSE_CODE(0x6F05, "Drive region must be permanent/region reset count error") +SENSE_CODE(0x6F06, "Insufficient block count for binding nonce recording") +SENSE_CODE(0x6F07, "Conflict in binding nonce recording") +/* + * SENSE_CODE(0x70NN, "Decompression exception short algorithm id of nn") + */ +SENSE_CODE(0x7100, "Decompression exception long algorithm id") + +SENSE_CODE(0x7200, "Session fixation error") +SENSE_CODE(0x7201, "Session fixation error writing lead-in") +SENSE_CODE(0x7202, "Session fixation error writing lead-out") +SENSE_CODE(0x7203, "Session fixation error - incomplete track in session") +SENSE_CODE(0x7204, "Empty or partially written reserved track") +SENSE_CODE(0x7205, "No more track reservations allowed") +SENSE_CODE(0x7206, "RMZ extension is not allowed") +SENSE_CODE(0x7207, "No more test zone extensions are allowed") + +SENSE_CODE(0x7300, "Cd control error") +SENSE_CODE(0x7301, "Power calibration area almost full") +SENSE_CODE(0x7302, "Power calibration area is full") +SENSE_CODE(0x7303, "Power calibration area error") +SENSE_CODE(0x7304, "Program memory area update failure") +SENSE_CODE(0x7305, "Program memory area is full") +SENSE_CODE(0x7306, "RMA/PMA is almost full") +SENSE_CODE(0x7310, "Current power calibration area almost full") +SENSE_CODE(0x7311, "Current power calibration area is full") +SENSE_CODE(0x7317, "RDZ is full") + +SENSE_CODE(0x7400, "Security error") +SENSE_CODE(0x7401, "Unable to decrypt data") +SENSE_CODE(0x7402, "Unencrypted data encountered while decrypting") +SENSE_CODE(0x7403, "Incorrect data encryption key") +SENSE_CODE(0x7404, "Cryptographic integrity validation failed") +SENSE_CODE(0x7405, "Error decrypting data") +SENSE_CODE(0x7406, "Unknown signature verification key") +SENSE_CODE(0x7407, "Encryption parameters not useable") +SENSE_CODE(0x7408, "Digital signature validation failure") +SENSE_CODE(0x7409, "Encryption mode mismatch on read") +SENSE_CODE(0x740A, "Encrypted block not raw read enabled") +SENSE_CODE(0x740B, "Incorrect Encryption parameters") +SENSE_CODE(0x740C, "Unable to decrypt parameter list") +SENSE_CODE(0x740D, "Encryption algorithm disabled") +SENSE_CODE(0x7410, "SA creation parameter value invalid") +SENSE_CODE(0x7411, "SA creation parameter value rejected") +SENSE_CODE(0x7412, "Invalid SA usage") +SENSE_CODE(0x7421, "Data Encryption configuration prevented") +SENSE_CODE(0x7430, "SA creation parameter not supported") +SENSE_CODE(0x7440, "Authentication failed") +SENSE_CODE(0x7461, "External data encryption key manager access error") +SENSE_CODE(0x7462, "External data encryption key manager error") +SENSE_CODE(0x7463, "External data encryption key not found") +SENSE_CODE(0x7464, "External data encryption request not authorized") +SENSE_CODE(0x746E, "External data encryption control timeout") +SENSE_CODE(0x746F, "External data encryption control error") +SENSE_CODE(0x7471, "Logical unit access not authorized") +SENSE_CODE(0x7479, "Security conflict in translated device")
This is a purely mechanical move of the list of additional sense codes to a separate file, in preparation for reducing the impact of choosing CONFIG_SCSI_CONSTANTS=y by about 8k. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> --- drivers/scsi/constants.c | 830 +-------------------------------------------- drivers/scsi/sense_codes.h | 826 ++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 829 insertions(+), 827 deletions(-) create mode 100644 drivers/scsi/sense_codes.h