| Message ID | 1456389222-12738-6-git-send-email-pankaj.dubey@samsung.com (mailing list archive) |
|---|---|
| State | Superseded, archived |
| Headers | show |
On Thu, Feb 25, 2016 at 02:03:41PM +0530, Pankaj Dubey wrote: > From: Pavel Fedin <p.fedin@samsung.com> > > Add documentation for new subnode properties, allowing bank configuration. > Based on u-boot implementation, but heavily reworked. > > Also, fix size of SROMc mapping in the example. Fix it in the previous patch. > CC: devicetree@vger.kernel.org > Signed-off-by: Pavel Fedin <p.fedin@samsung.com> > Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> > Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> > Acked-by: Rob Herring <robh@kernel.org> > Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> > --- > .../bindings/memory-controllers/exynos-srom.txt | 73 +++++++++++++++++++++- > 1 file changed, 71 insertions(+), 2 deletions(-) > > diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt > index 33886d5..e5c18df 100644 > --- a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt > +++ b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt > @@ -5,8 +5,77 @@ Required properties: > > - reg: offset and length of the register set > > -Example: > +Optional properties: > +The SROM controller can be used to attach external peripherals. In this case > +extra properties, describing the bus behind it, should be specified as below: > + > +- #address-cells: Must be set to 2 to allow device address translation. > + Address is specified as (bank#, offset). > + > +- #size-cells: Must be set to 1 to allow device size passing > + > +- ranges: Must be set up to reflect the memory layout with four integer values > + per bank: > + <bank-number> 0 <parent address of bank> <size> > + > +Sub-nodes: > +The actual device nodes should be added as subnodes to the SROMc node. These > +subnodes, except regular device specification, should contain the following s/except/in addition to/ > +properties, describing configuration of the relevant SROM bank: > + > +Required properties: > +- reg: bank number, base address (relative to start of the bank) and size of > + the memory mapped for the device. Note that base address will be > + typically 0 as this is the start of the bank. > + > +- samsung,srom-timing : array of 6 integers, specifying bank timings in the > + following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs. > + Each value is specified in cycles and has the following > + meaning and valid range: > + Tacp : Page mode access cycle at Page mode (0 - 15) > + Tcah : Address holding time after CSn (0 - 15) > + Tcoh : Chip selection hold on OEn (0 - 15) > + Tacc : Access cycle (0 - 31, the actual time is N + 1) > + Tcos : Chip selection set-up before OEn (0 - 15) > + Tacs : Address set-up before CSn (0 - 15) > + > +Optional properties: > +- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used. > + > +- samsung,srom-page-mode : page mode configuration for the bank: > + 0 - normal (one data) > + 1 - four data > + If omitted, default of 0 is used. Make this a bool instead. Rob -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi, On Wednesday 02 March 2016 11:27 PM, Rob Herring wrote: > On Thu, Feb 25, 2016 at 02:03:41PM +0530, Pankaj Dubey wrote: >> From: Pavel Fedin <p.fedin@samsung.com> >> >> Add documentation for new subnode properties, allowing bank configuration. >> Based on u-boot implementation, but heavily reworked. >> >> Also, fix size of SROMc mapping in the example. > > Fix it in the previous patch. OK. > >> CC: devicetree@vger.kernel.org >> Signed-off-by: Pavel Fedin <p.fedin@samsung.com> >> Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> >> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> >> Acked-by: Rob Herring <robh@kernel.org> >> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> >> --- >> .../bindings/memory-controllers/exynos-srom.txt | 73 +++++++++++++++++++++- >> 1 file changed, 71 insertions(+), 2 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt >> index 33886d5..e5c18df 100644 >> --- a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt >> +++ b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt >> @@ -5,8 +5,77 @@ Required properties: >> >> - reg: offset and length of the register set >> >> -Example: >> +Optional properties: >> +The SROM controller can be used to attach external peripherals. In this case >> +extra properties, describing the bus behind it, should be specified as below: >> + >> +- #address-cells: Must be set to 2 to allow device address translation. >> + Address is specified as (bank#, offset). >> + >> +- #size-cells: Must be set to 1 to allow device size passing >> + >> +- ranges: Must be set up to reflect the memory layout with four integer values >> + per bank: >> + <bank-number> 0 <parent address of bank> <size> >> + >> +Sub-nodes: >> +The actual device nodes should be added as subnodes to the SROMc node. These >> +subnodes, except regular device specification, should contain the following > > s/except/in addition to/ > OK. Will update this description as suggested. >> +properties, describing configuration of the relevant SROM bank: >> + >> +Required properties: >> +- reg: bank number, base address (relative to start of the bank) and size of >> + the memory mapped for the device. Note that base address will be >> + typically 0 as this is the start of the bank. >> + >> +- samsung,srom-timing : array of 6 integers, specifying bank timings in the >> + following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs. >> + Each value is specified in cycles and has the following >> + meaning and valid range: >> + Tacp : Page mode access cycle at Page mode (0 - 15) >> + Tcah : Address holding time after CSn (0 - 15) >> + Tcoh : Chip selection hold on OEn (0 - 15) >> + Tacc : Access cycle (0 - 31, the actual time is N + 1) >> + Tcos : Chip selection set-up before OEn (0 - 15) >> + Tacs : Address set-up before CSn (0 - 15) >> + >> +Optional properties: >> +- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used. >> + >> +- samsung,srom-page-mode : page mode configuration for the bank: >> + 0 - normal (one data) >> + 1 - four data >> + If omitted, default of 0 is used. > > Make this a bool instead. > I do not have strong objections to change this, but I can see doing so will increase two or three lines in driver, as such this property is not being used as bool in driver. Sorry to say this but I do not understand why these comments are coming now? Whereas you had given your "Acked-by" to the same patch when it was posted previously by Pavel and we were keeping this driver under "drivers/soc/samsung". Is it just because we are moving to "drivers/memory" and it needs to be consistent with other memory controller drivers? Thanks, Pankaj Dubey > Rob > > -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt index 33886d5..e5c18df 100644 --- a/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt +++ b/Documentation/devicetree/bindings/memory-controllers/exynos-srom.txt @@ -5,8 +5,77 @@ Required properties: - reg: offset and length of the register set -Example: +Optional properties: +The SROM controller can be used to attach external peripherals. In this case +extra properties, describing the bus behind it, should be specified as below: + +- #address-cells: Must be set to 2 to allow device address translation. + Address is specified as (bank#, offset). + +- #size-cells: Must be set to 1 to allow device size passing + +- ranges: Must be set up to reflect the memory layout with four integer values + per bank: + <bank-number> 0 <parent address of bank> <size> + +Sub-nodes: +The actual device nodes should be added as subnodes to the SROMc node. These +subnodes, except regular device specification, should contain the following +properties, describing configuration of the relevant SROM bank: + +Required properties: +- reg: bank number, base address (relative to start of the bank) and size of + the memory mapped for the device. Note that base address will be + typically 0 as this is the start of the bank. + +- samsung,srom-timing : array of 6 integers, specifying bank timings in the + following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs. + Each value is specified in cycles and has the following + meaning and valid range: + Tacp : Page mode access cycle at Page mode (0 - 15) + Tcah : Address holding time after CSn (0 - 15) + Tcoh : Chip selection hold on OEn (0 - 15) + Tacc : Access cycle (0 - 31, the actual time is N + 1) + Tcos : Chip selection set-up before OEn (0 - 15) + Tacs : Address set-up before CSn (0 - 15) + +Optional properties: +- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used. + +- samsung,srom-page-mode : page mode configuration for the bank: + 0 - normal (one data) + 1 - four data + If omitted, default of 0 is used. + +Example: basic definition, no banks are configured + sromc@12570000 { + compatible = "samsung,exynos-srom"; + reg = <0x12570000 0x14>; + }; + +Example: SROMc with SMSC911x ethernet chip on bank 3 sromc@12570000 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x04000000 0x20000 // Bank0 + 1 0 0x05000000 0x20000 // Bank1 + 2 0 0x06000000 0x20000 // Bank2 + 3 0 0x07000000 0x20000>; // Bank3 + compatible = "samsung,exynos-srom"; - reg = <0x12570000 0x10>; + reg = <0x12570000 0x14>; + + ethernet@3,0 { + compatible = "smsc,lan9115"; + reg = <3 0 0x10000>; // Bank 3, offset = 0 + phy-mode = "mii"; + interrupt-parent = <&gpx0>; + interrupts = <5 8>; + reg-io-width = <2>; + smsc,irq-push-pull; + smsc,force-internal-phy; + + samsung,srom-page-mode = <1>; + samsung,srom-timing = <9 12 1 9 1 1>; + }; };