@@ -735,6 +735,7 @@ config SERIAL_SH_SCI
tristate "SuperH SCI(F) serial port support"
depends on SUPERH || ARCH_RENESAS || H8300 || COMPILE_TEST
select SERIAL_CORE
+ select SERIAL_MCTRL_GPIO if GPIOLIB
config SERIAL_SH_SCI_NR_UARTS
int "Maximum number of SCI(F) serial ports"
@@ -57,6 +57,7 @@
#include <asm/sh_bios.h>
#endif
+#include "serial_mctrl_gpio.h"
#include "sh-sci.h"
/* Offsets into the sci_port->irqs array */
@@ -111,6 +112,7 @@ struct sci_port {
unsigned int error_clear;
unsigned int sampling_rate_mask;
resource_size_t reg_size;
+ struct mctrl_gpios *gpios;
/* Break timer */
struct timer_list break_timer;
@@ -1817,6 +1819,8 @@ static unsigned int sci_tx_empty(struct uart_port *port)
*/
static void sci_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
+ struct sci_port *s = to_sci_port(port);
+
if (mctrl & TIOCM_LOOP) {
const struct plat_sci_reg *reg;
@@ -1829,15 +1833,35 @@ static void sci_set_mctrl(struct uart_port *port, unsigned int mctrl)
serial_port_in(port, SCFCR) |
SCFCR_LOOP);
}
+
+ mctrl_gpio_set(s->gpios, mctrl);
}
static unsigned int sci_get_mctrl(struct uart_port *port)
{
+ struct sci_port *s = to_sci_port(port);
+ struct mctrl_gpios *gpios = s->gpios;
+ unsigned int mctrl = 0;
+
+ mctrl_gpio_get(gpios, &mctrl);
+
/*
* CTS/RTS is handled in hardware when supported, while nothing
* else is wired up. Keep it simple and simply assert CTS/DSR/CAR.
*/
- return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+ if (IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(gpios, UART_GPIO_CTS)))
+ mctrl |= TIOCM_CTS;
+ if (IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(gpios, UART_GPIO_DSR)))
+ mctrl |= TIOCM_DSR;
+ if (IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(gpios, UART_GPIO_DCD)))
+ mctrl |= TIOCM_CAR;
+
+ return mctrl;
+}
+
+static void sci_enable_ms(struct uart_port *port)
+{
+ mctrl_gpio_enable_ms(to_sci_port(port)->gpios);
}
static void sci_break_ctl(struct uart_port *port, int break_state)
@@ -1899,6 +1923,8 @@ static void sci_shutdown(struct uart_port *port)
dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
+ mctrl_gpio_disable_ms(to_sci_port(port)->gpios);
+
spin_lock_irqsave(&port->lock, flags);
sci_stop_rx(port);
sci_stop_tx(port);
@@ -2300,6 +2326,9 @@ done:
sci_start_rx(port);
sci_port_disable(s);
+
+ if (UART_ENABLE_MS(port, termios->c_cflag))
+ sci_enable_ms(port);
}
static void sci_pm(struct uart_port *port, unsigned int state,
@@ -2425,6 +2454,7 @@ static struct uart_ops sci_uart_ops = {
.start_tx = sci_start_tx,
.stop_tx = sci_stop_tx,
.stop_rx = sci_stop_rx,
+ .enable_ms = sci_enable_ms,
.break_ctl = sci_break_ctl,
.startup = sci_startup,
.shutdown = sci_shutdown,
@@ -2912,6 +2942,20 @@ static int sci_probe_single(struct platform_device *dev,
if (ret)
return ret;
+ sciport->gpios = mctrl_gpio_init(&sciport->port, 0);
+ if (IS_ERR(sciport->gpios) && PTR_ERR(sciport->gpios) != -ENOSYS)
+ return PTR_ERR(sciport->gpios);
+
+ if (p->capabilities & SCIx_HAVE_RTSCTS) {
+ if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(sciport->gpios,
+ UART_GPIO_CTS)) ||
+ !IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(sciport->gpios,
+ UART_GPIO_RTS))) {
+ dev_err(&dev->dev, "Conflicting RTS/CTS config\n");
+ return -EINVAL;
+ }
+ }
+
ret = uart_add_one_port(&sci_uart_driver, &sciport->port);
if (ret) {
sci_cleanup_single(sciport);
Enhance the Renesas SCI UART driver to add support for GPIO-controlled modem lines (CTS, DSR, DCD, RNG, RTS, DTR), using the serial_mctrl_gpio helpers. GPIO-controlled modem lines can be used when dedicated modem lines are not available. Invalid configurations specifying both GPIO RTS/CTS and dedicated RTS/CTS are rejected. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- Testing for regressions on platforms without DT and/or GPIOLIB support (SuperH) would be appreciated. Compile-tested on ecovec24_defconfig(GPIOLIB=y) and se7780_defconfig (GPIOLIB=n). v2: - Drop RFC status. - Fix typo s/UART_GPIO_CAR/UART_GPIO_DCD/ (too many different names for the same thing: CAR, DCD, CD), - Drop OUT[12] from the patch description, - Use intermediate variables to avoid breaking long lines, - Reject combining GPIO and dedicated RTS/CTS. --- drivers/tty/serial/Kconfig | 1 + drivers/tty/serial/sh-sci.c | 46 ++++++++++++++++++++++++++++++++++++++++++++- 2 files changed, 46 insertions(+), 1 deletion(-)