| Message ID | 1465484030-28838-5-git-send-email-benjamin.tissoires@redhat.com (mailing list archive) |
|---|---|
| State | Under Review, archived |
| Headers | show |
Hi Benjamin, On Thu, Jun 09, 2016 at 04:53:50PM +0200, Benjamin Tissoires wrote: > + > +struct mapping_table_entry { > + u16 rmiaddr; Should be __le16 rmiaddr, otherwise: CHECK drivers/input/rmi4/rmi_smbus.c drivers/input/rmi4/rmi_smbus.c:116:33: warning: incorrect type in assignment (different base types) drivers/input/rmi4/rmi_smbus.c:116:33: expected unsigned short [unsigned] [usertype] rmiaddr drivers/input/rmi4/rmi_smbus.c:116:33: got restricted __le16 [usertype] <noident> > + > +static struct i2c_driver rmi_smb_driver; > + I do not think this forward declaration is needed. > + > +#ifdef CONFIG_PM_SLEEP > +static int rmi_smb_suspend(struct device *dev) __maybe_unused instead of #ifdef. > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); > + int ret; > + > + ret = rmi_driver_suspend(rmi_smb->xport.rmi_dev); > + if (ret) > + dev_warn(dev, "Failed to suspend device: %d\n", ret); > + > + return ret; > +} > +#endif > + > +#ifdef CONFIG_PM > +static int rmi_smb_runtime_suspend(struct device *dev) Same here? > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); > + int ret; > + > + ret = rmi_driver_suspend(rmi_smb->xport.rmi_dev); > + if (ret) > + dev_warn(dev, "Failed to suspend device: %d\n", ret); > + > + return 0; > +} > + > +static int rmi_smb_runtime_resume(struct device *dev) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); > + int ret; > + > + ret = rmi_driver_resume(rmi_smb->xport.rmi_dev); > + if (ret) > + dev_warn(dev, "Failed to resume device: %d\n", ret); > + > + return 0; > +} > +#endif > + > +static const struct dev_pm_ops rmi_smb_pm = { > + SET_SYSTEM_SLEEP_PM_OPS(rmi_smb_suspend, NULL) > + SET_RUNTIME_PM_OPS(rmi_smb_runtime_suspend, rmi_smb_runtime_resume, > + NULL) > +}; > + > +static int rmi_smb_resume(struct device *dev) > +{ > + struct i2c_client *client = container_of(dev, struct i2c_client, dev); > + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); > + struct rmi_device *rmi_dev = rmi_smb->xport.rmi_dev; > + int ret; > + > + rmi_smb_reset(&rmi_smb->xport, 0); > + > + rmi_reset(rmi_dev); > + > + ret = rmi_driver_resume(rmi_smb->xport.rmi_dev); > + if (ret) > + dev_warn(dev, "Failed to resume device: %d\n", ret); > + > + return 0; > +} > + > +static const struct i2c_device_id rmi_id[] = { > + { "rmi4_smbus", 0 }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, rmi_id); > + > +static struct i2c_driver rmi_smb_driver = { > + .driver = { > + .owner = THIS_MODULE, > + .name = "rmi4_smbus", > + .pm = &rmi_smb_pm, > + .resume = rmi_smb_resume, Why rmi_smb_resume is not part of rmi_smb_pm? Thanks.
On Jun 23 2016 or thereabouts, Dmitry Torokhov wrote: > Hi Benjamin, > > On Thu, Jun 09, 2016 at 04:53:50PM +0200, Benjamin Tissoires wrote: > > + > > +struct mapping_table_entry { > > + u16 rmiaddr; > > Should be __le16 rmiaddr, otherwise: > > CHECK drivers/input/rmi4/rmi_smbus.c > drivers/input/rmi4/rmi_smbus.c:116:33: warning: incorrect type in assignment (different base types) > drivers/input/rmi4/rmi_smbus.c:116:33: expected unsigned short [unsigned] [usertype] rmiaddr > drivers/input/rmi4/rmi_smbus.c:116:33: got restricted __le16 [usertype] <noident> > > > + > > +static struct i2c_driver rmi_smb_driver; > > + > > I do not think this forward declaration is needed. > > > + > > +#ifdef CONFIG_PM_SLEEP > > +static int rmi_smb_suspend(struct device *dev) > > __maybe_unused instead of #ifdef. > > > +{ > > + struct i2c_client *client = to_i2c_client(dev); > > + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); > > + int ret; > > + > > + ret = rmi_driver_suspend(rmi_smb->xport.rmi_dev); > > + if (ret) > > + dev_warn(dev, "Failed to suspend device: %d\n", ret); > > + > > + return ret; > > +} > > +#endif > > + > > +#ifdef CONFIG_PM > > +static int rmi_smb_runtime_suspend(struct device *dev) > > Same here? > > > +{ > > + struct i2c_client *client = to_i2c_client(dev); > > + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); > > + int ret; > > + > > + ret = rmi_driver_suspend(rmi_smb->xport.rmi_dev); > > + if (ret) > > + dev_warn(dev, "Failed to suspend device: %d\n", ret); > > + > > + return 0; > > +} > > + > > +static int rmi_smb_runtime_resume(struct device *dev) > > +{ > > + struct i2c_client *client = to_i2c_client(dev); > > + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); > > + int ret; > > + > > + ret = rmi_driver_resume(rmi_smb->xport.rmi_dev); > > + if (ret) > > + dev_warn(dev, "Failed to resume device: %d\n", ret); > > + > > + return 0; > > +} > > +#endif > > + > > +static const struct dev_pm_ops rmi_smb_pm = { > > + SET_SYSTEM_SLEEP_PM_OPS(rmi_smb_suspend, NULL) > > + SET_RUNTIME_PM_OPS(rmi_smb_runtime_suspend, rmi_smb_runtime_resume, > > + NULL) > > +}; > > + > > +static int rmi_smb_resume(struct device *dev) > > +{ > > + struct i2c_client *client = container_of(dev, struct i2c_client, dev); > > + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); > > + struct rmi_device *rmi_dev = rmi_smb->xport.rmi_dev; > > + int ret; > > + > > + rmi_smb_reset(&rmi_smb->xport, 0); > > + > > + rmi_reset(rmi_dev); > > + > > + ret = rmi_driver_resume(rmi_smb->xport.rmi_dev); > > + if (ret) > > + dev_warn(dev, "Failed to resume device: %d\n", ret); > > + > > + return 0; > > +} > > + > > +static const struct i2c_device_id rmi_id[] = { > > + { "rmi4_smbus", 0 }, > > + { } > > +}; > > +MODULE_DEVICE_TABLE(i2c, rmi_id); > > + > > +static struct i2c_driver rmi_smb_driver = { > > + .driver = { > > + .owner = THIS_MODULE, > > + .name = "rmi4_smbus", > > + .pm = &rmi_smb_pm, > > + .resume = rmi_smb_resume, > > Why rmi_smb_resume is not part of rmi_smb_pm? > This is because rmi_smbus device both have a PS/2 interface and a SMBus one. I'll have to check again now that I have a slightly different way of binding smbus devices in my tree, but the issue was: - having resume part of pm means it will get caught by PM directly - the PS/2 node gets also resumed by PM - calling PS/2 commands during resume switches the devices back into PS/2 and stops the SMBus communication. So it's easier to wait only for the PS/2 PM resume call which will call the SMBus resume function when the device is in a proper state. I'll send out the updated patch with your comments next week hopefully. Cheers, Benjamin -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Jun 24, 2016 at 09:19:32AM +0200, Benjamin Tissoires wrote: > On Jun 23 2016 or thereabouts, Dmitry Torokhov wrote: > > On Thu, Jun 09, 2016 at 04:53:50PM +0200, Benjamin Tissoires wrote: > > > + > > > +static struct i2c_driver rmi_smb_driver = { > > > + .driver = { > > > + .owner = THIS_MODULE, > > > + .name = "rmi4_smbus", > > > + .pm = &rmi_smb_pm, > > > + .resume = rmi_smb_resume, > > > > Why rmi_smb_resume is not part of rmi_smb_pm? > > > > This is because rmi_smbus device both have a PS/2 interface and a SMBus > one. I'll have to check again now that I have a slightly different way > of binding smbus devices in my tree, but the issue was: > - having resume part of pm means it will get caught by PM directly > - the PS/2 node gets also resumed by PM > - calling PS/2 commands during resume switches the devices back into > PS/2 and stops the SMBus communication. > > So it's easier to wait only for the PS/2 PM resume call which will call > the SMBus resume function when the device is in a proper state. > > I'll send out the updated patch with your comments next week hopefully. Hmm, I think you will have to walk me through resume process. How do we tie in PS/2 and I2C on these devices abd have PS/2 code call into this driver? Thanks.
On Jun 24 2016 or thereabouts, Dmitry Torokhov wrote: > On Fri, Jun 24, 2016 at 09:19:32AM +0200, Benjamin Tissoires wrote: > > On Jun 23 2016 or thereabouts, Dmitry Torokhov wrote: > > > On Thu, Jun 09, 2016 at 04:53:50PM +0200, Benjamin Tissoires wrote: > > > > + > > > > +static struct i2c_driver rmi_smb_driver = { > > > > + .driver = { > > > > + .owner = THIS_MODULE, > > > > + .name = "rmi4_smbus", > > > > + .pm = &rmi_smb_pm, > > > > + .resume = rmi_smb_resume, > > > > > > Why rmi_smb_resume is not part of rmi_smb_pm? > > > > > > > This is because rmi_smbus device both have a PS/2 interface and a SMBus > > one. I'll have to check again now that I have a slightly different way > > of binding smbus devices in my tree, but the issue was: > > - having resume part of pm means it will get caught by PM directly > > - the PS/2 node gets also resumed by PM > > - calling PS/2 commands during resume switches the devices back into > > PS/2 and stops the SMBus communication. > > > > So it's easier to wait only for the PS/2 PM resume call which will call > > the SMBus resume function when the device is in a proper state. > > > > I'll send out the updated patch with your comments next week hopefully. > > Hmm, I think you will have to walk me through resume process. How do we > tie in PS/2 and I2C on these devices abd have PS/2 code call into this > driver? > Sure. For starters, here is my latest WIP (I need to rework on the series for commit messages and probably squash some patches): https://github.com/bentiss/linux/commits/synaptics-rmi4-smbus-v4.7-rc4%2B Then, let me explain the problems we have with those touchpads and the resume process. The touchpads are both connected to PS/2 and SMBus as you know. However, there is no SMBus enumeration entry anywhere in the system. Luckily, the PS/2 chip is aware of the other bus, and can be polled to request whether or not we are confronted to a RMI4 over SMBus device (see https://github.com/bentiss/linux/commit/a3e67de764656201522962028bc783fc4b921de3 ) Of course, to make those touchpads robust with reboots and allow legacy drivers (PS/2) to use them, the firmware tend to switch back to PS/2 as soon as you issue a PS/2 reset command or if you send some other PS/2 commands. The problem we have is that if you send some various PS/2 commands to the touchpad, it disconnects from the SMBus entirely (it took me one year to understand why the device was not showing up on I2C). The last interesting fact for those touchpad is that you need to enable SMBus communication by issuing a SMB_PROTOCOL_VERSION_ADDRESS command. If you do not issue this after a PS/2 reset, the device is muted over SMBus. So, to be sure we can query the touchpad from PS/2 and to control the PS/2 commands and the resume, I have in the series above a separate PS/2 driver for this touchpad. The regular psmouse driver probes the PS/2 chip, but aborts seeing the SMBus capability. Then rmi_ps2 takes over and binds to the PS/2 chip to fill in the platform data required by rmi_smbus (https://github.com/bentiss/linux/commit/3ceb7c80ecee17a86b8ae8476211c7498cc823d2) If we simply unbind the PS/2 node and let it dangling, the serio driver issues a reconnect after resume on both the PS/2 chip of the touchpad, and the PS/2 pass-through node of the trackstick. But if the PS/2 chip of the touchpad is left dangling, the resume process will first call a reconnect on the pass-through, then on the touchpad through the enumeration of the serio bus, which will reset the touchpad and messed up the pass-through node and the rmi-smbus driver. So keeping around a reference to the PS/2 node allows to set this node as a parent of the pass-through trackstick node and guarantees that the touchpad will be resumed before the trackstick. One final thing. I tried not having rmi_ps2 calling the .resume callback of rmi_smbus and keeping rmi_smbus as a PM. But the issue is that the serio driver sends the reset command in a workqueue as it can takes some time: - serio gets resume called -> prepare the worker for the resume/reconnect process - rmi_smbus gets resumed -> OK - the worker kicks in, reset the PS/2 lines, and shuts down the rmi_smbus device I also tried one thing where I did not bind the PS/2 touchpad at all (and having some kind of platform driver to bind rmi_smbus). And of course, grub initializes the touchpad, so it disconnects on I2C and you can't bind it on SMBus, ever :) I think that's all I know on these touchpads and this is all the mess I can present. If you have a better option, I'm all ears as this is not clean, but I can't figure out a better way. Cheers, Benjamin -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/input/rmi4/Kconfig b/drivers/input/rmi4/Kconfig index f73df24..86a180b 100644 --- a/drivers/input/rmi4/Kconfig +++ b/drivers/input/rmi4/Kconfig @@ -27,6 +27,18 @@ config RMI4_SPI If unsure, say N. +config RMI4_SMB + tristate "RMI4 SMB Support" + depends on RMI4_CORE && I2C + help + Say Y here if you want to support RMI4 devices connected to an SMB + bus. + + If unsure, say N. + + To compile this driver as a module, choose M here: the module will be + called rmi_smbus. + config RMI4_2D_SENSOR bool depends on RMI4_CORE diff --git a/drivers/input/rmi4/Makefile b/drivers/input/rmi4/Makefile index 95c00a7..3c8ebf2 100644 --- a/drivers/input/rmi4/Makefile +++ b/drivers/input/rmi4/Makefile @@ -11,3 +11,4 @@ rmi_core-$(CONFIG_RMI4_F30) += rmi_f30.o # Transports obj-$(CONFIG_RMI4_I2C) += rmi_i2c.o obj-$(CONFIG_RMI4_SPI) += rmi_spi.o +obj-$(CONFIG_RMI4_SMB) += rmi_smbus.o diff --git a/drivers/input/rmi4/rmi_bus.h b/drivers/input/rmi4/rmi_bus.h index 8995798..b7625a9 100644 --- a/drivers/input/rmi4/rmi_bus.h +++ b/drivers/input/rmi4/rmi_bus.h @@ -105,6 +105,18 @@ rmi_get_platform_data(struct rmi_device *d) bool rmi_is_physical_device(struct device *dev); /** + * rmi_reset - reset a RMI4 device + * @d: Pointer to an RMI device + * + * Calls for a reset of each function implemented by a specific device. + * Returns 0 on success or a negative error code. + */ +static inline int rmi_reset(struct rmi_device *d) +{ + return d->driver->reset_handler(d); +} + +/** * rmi_read - read a single byte * @d: Pointer to an RMI device * @addr: The address to read from diff --git a/drivers/input/rmi4/rmi_smbus.c b/drivers/input/rmi4/rmi_smbus.c new file mode 100644 index 0000000..d60b0e9 --- /dev/null +++ b/drivers/input/rmi4/rmi_smbus.c @@ -0,0 +1,470 @@ +/* + * Copyright (c) 2015 - 2016 Red Hat, Inc + * Copyright (c) 2011, 2012 Synaptics Incorporated + * Copyright (c) 2011 Unixphere + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/delay.h> +#include <linux/i2c.h> +#include <linux/interrupt.h> +#include <linux/kconfig.h> +#include <linux/lockdep.h> +#include <linux/module.h> +#include <linux/pm.h> +#include <linux/rmi.h> +#include <linux/slab.h> +#include "rmi_driver.h" + +#define SMB_PROTOCOL_VERSION_ADDRESS 0xfd +#define SMB_MAX_COUNT 32 +#define RMI_SMB2_MAP_SIZE 8 /* 8 entry of 4 bytes each */ +#define RMI_SMB2_MAP_FLAGS_WE 0x01 + +struct mapping_table_entry { + u16 rmiaddr; + u8 readcount; + u8 flags; +}; + +struct rmi_smb_xport { + struct rmi_transport_dev xport; + struct i2c_client *client; + + struct mutex page_mutex; + int page; + u8 table_index; + struct mutex mappingtable_mutex; + struct mapping_table_entry mapping_table[RMI_SMB2_MAP_SIZE]; +}; + +static int rmi_smb_get_version(struct rmi_smb_xport *rmi_smb) +{ + struct i2c_client *client = rmi_smb->client; + int retval; + + /* Check if for SMBus new version device by reading version byte. */ + retval = i2c_smbus_read_byte_data(client, SMB_PROTOCOL_VERSION_ADDRESS); + if (retval < 0) { + dev_err(&client->dev, "failed to get SMBus version number!\n"); + return retval; + } + return retval + 1; +} + +/* SMB block write - wrapper over ic2_smb_write_block */ +static int smb_block_write(struct rmi_transport_dev *xport, + u8 commandcode, const void *buf, size_t len) +{ + struct rmi_smb_xport *rmi_smb = + container_of(xport, struct rmi_smb_xport, xport); + struct i2c_client *client = rmi_smb->client; + int retval; + + retval = i2c_smbus_write_block_data(client, commandcode, len, buf); + + rmi_dbg(RMI_DEBUG_XPORT, &client->dev, + "wrote %zd bytes at %#04x: %d (%*ph)\n", + len, commandcode, retval, (int)len, buf); + + return retval; +} + +/* + * The function to get command code for smbus operations and keeps + * records to the driver mapping table + */ +static int rmi_smb_get_command_code(struct rmi_transport_dev *xport, + u16 rmiaddr, int bytecount, bool isread, u8 *commandcode) +{ + struct rmi_smb_xport *rmi_smb = + container_of(xport, struct rmi_smb_xport, xport); + int i; + int retval; + struct mapping_table_entry mapping_data[1]; + + mutex_lock(&rmi_smb->mappingtable_mutex); + for (i = 0; i < RMI_SMB2_MAP_SIZE; i++) { + if (rmi_smb->mapping_table[i].rmiaddr == rmiaddr) { + if (isread) { + if (rmi_smb->mapping_table[i].readcount + == bytecount) { + *commandcode = i; + retval = 0; + goto exit; + } + } else { + if (rmi_smb->mapping_table[i].flags & + RMI_SMB2_MAP_FLAGS_WE) { + *commandcode = i; + retval = 0; + goto exit; + } + } + } + } + i = rmi_smb->table_index; + rmi_smb->table_index = (i + 1) % RMI_SMB2_MAP_SIZE; + + /* constructs mapping table data entry. 4 bytes each entry */ + memset(mapping_data, 0, sizeof(mapping_data)); + + mapping_data[0].rmiaddr = cpu_to_le16(rmiaddr); + mapping_data[0].readcount = bytecount; + mapping_data[0].flags = !isread ? RMI_SMB2_MAP_FLAGS_WE : 0; + + retval = smb_block_write(xport, i + 0x80, mapping_data, + sizeof(mapping_data)); + + if (retval < 0) { + /* + * if not written to device mapping table + * clear the driver mapping table records + */ + rmi_smb->mapping_table[i].rmiaddr = 0x0000; + rmi_smb->mapping_table[i].readcount = 0; + rmi_smb->mapping_table[i].flags = 0; + goto exit; + } + /* save to the driver level mapping table */ + rmi_smb->mapping_table[i].rmiaddr = rmiaddr; + rmi_smb->mapping_table[i].readcount = bytecount; + rmi_smb->mapping_table[i].flags = !isread ? RMI_SMB2_MAP_FLAGS_WE : 0; + *commandcode = i; + +exit: + mutex_unlock(&rmi_smb->mappingtable_mutex); + + return retval; +} + +static int rmi_smb_write_block(struct rmi_transport_dev *xport, u16 rmiaddr, + const void *databuff, size_t len) +{ + int retval = 0; + u8 commandcode; + struct rmi_smb_xport *rmi_smb = + container_of(xport, struct rmi_smb_xport, xport); + int cur_len = (int)len; + + mutex_lock(&rmi_smb->page_mutex); + + while (cur_len > 0) { + /* + * break into 32 bytes chunks to write get command code + */ + int block_len = min_t(int, len, SMB_MAX_COUNT); + + retval = rmi_smb_get_command_code(xport, rmiaddr, block_len, + false, &commandcode); + if (retval < 0) + goto exit; + + retval = smb_block_write(xport, commandcode, + databuff, block_len); + if (retval < 0) + goto exit; + + /* prepare to write next block of bytes */ + cur_len -= SMB_MAX_COUNT; + databuff += SMB_MAX_COUNT; + rmiaddr += SMB_MAX_COUNT; + } +exit: + mutex_unlock(&rmi_smb->page_mutex); + return retval; +} + +/* SMB block read - wrapper over ic2_smb_read_block */ +static int smb_block_read(struct rmi_transport_dev *xport, + u8 commandcode, void *buf, size_t len) +{ + struct rmi_smb_xport *rmi_smb = + container_of(xport, struct rmi_smb_xport, xport); + struct i2c_client *client = rmi_smb->client; + int retval; + + retval = i2c_smbus_read_block_data(client, commandcode, buf); + if (retval < 0) + return retval; + + return retval; +} + +static int rmi_smb_read_block(struct rmi_transport_dev *xport, u16 rmiaddr, + void *databuff, size_t len) +{ + struct rmi_smb_xport *rmi_smb = + container_of(xport, struct rmi_smb_xport, xport); + int retval; + u8 commandcode; + int cur_len = (int)len; + + mutex_lock(&rmi_smb->page_mutex); + memset(databuff, 0, len); + + while (cur_len > 0) { + /* break into 32 bytes chunks to write get command code */ + int block_len = min_t(int, cur_len, SMB_MAX_COUNT); + + retval = rmi_smb_get_command_code(xport, rmiaddr, block_len, + true, &commandcode); + if (retval < 0) + goto exit; + + retval = smb_block_read(xport, commandcode, + databuff, block_len); + if (retval < 0) + goto exit; + + /* prepare to read next block of bytes */ + cur_len -= SMB_MAX_COUNT; + databuff += SMB_MAX_COUNT; + rmiaddr += SMB_MAX_COUNT; + } + + retval = 0; + +exit: + mutex_unlock(&rmi_smb->page_mutex); + return retval; +} + +static void rmi_smb_clear_state(struct rmi_smb_xport *rmi_smb) +{ + /* the mapping table has been flushed, discard the current one */ + mutex_lock(&rmi_smb->mappingtable_mutex); + memset(rmi_smb->mapping_table, 0, sizeof(rmi_smb->mapping_table)); + mutex_unlock(&rmi_smb->mappingtable_mutex); +} + +static int rmi_smb_enable_smbus_mode(struct rmi_smb_xport *rmi_smb) +{ + int retval; + + /* we need to get the smbus version to activate the touchpad */ + retval = rmi_smb_get_version(rmi_smb); + if (retval < 0) + return retval; + + return 0; +} + +static int rmi_smb_reset(struct rmi_transport_dev *xport, u16 reset_addr) +{ + struct rmi_smb_xport *rmi_smb = + container_of(xport, struct rmi_smb_xport, xport); + + rmi_smb_clear_state(rmi_smb); + + /* + * we do not call the actual reset command, it has to be handled in + * PS/2 or there will be races between PS/2 and SMBus. + * PS/2 should ensure that a psmouse_reset is called before + * intializing the device and after it has been removed to be in a known + * state. + */ + return rmi_smb_enable_smbus_mode(rmi_smb); +} + +static const struct rmi_transport_ops rmi_smb_ops = { + .write_block = rmi_smb_write_block, + .read_block = rmi_smb_read_block, + .reset = rmi_smb_reset, +}; + +static void rmi_smb_alert(struct i2c_client *client, + enum i2c_alert_protocol type, unsigned int data) +{ + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); + struct rmi_device *rmi_dev = rmi_smb->xport.rmi_dev; + struct rmi_driver_data *drv_data = dev_get_drvdata(&rmi_dev->dev); + + if (type != I2C_PROTOCOL_SMBUS_HOST_NOTIFY) + return; + + if (!drv_data) { + dev_err(&client->dev, + "Something went wrong, driver data is NULL.\n"); + return; + } + + rmi_process_interrupt_requests(rmi_dev); +} + +static struct i2c_driver rmi_smb_driver; + +static int rmi_smb_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct rmi_device_platform_data *pdata = dev_get_platdata(&client->dev); + struct rmi_smb_xport *rmi_smb; + int retval; + int smbus_version; + + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_READ_BLOCK_DATA | + I2C_FUNC_SMBUS_HOST_NOTIFY)) { + dev_err(&client->dev, + "adapter does not support required functionality.\n"); + return -ENODEV; + } + + rmi_smb = devm_kzalloc(&client->dev, sizeof(struct rmi_smb_xport), + GFP_KERNEL); + if (!rmi_smb) + return -ENOMEM; + + if (!pdata) { + dev_err(&client->dev, "no platform data, aborting\n"); + return -ENOMEM; + } + + rmi_dbg(RMI_DEBUG_XPORT, &client->dev, "Probing %s.\n", + dev_name(&client->dev)); + + rmi_smb->client = client; + mutex_init(&rmi_smb->page_mutex); + mutex_init(&rmi_smb->mappingtable_mutex); + + rmi_smb->xport.dev = &client->dev; + rmi_smb->xport.pdata = *pdata; + rmi_smb->xport.proto_name = "smb2"; + rmi_smb->xport.ops = &rmi_smb_ops; + + /* Check if for SMBus new version device by reading version byte. */ + retval = rmi_smb_get_version(rmi_smb); + if (retval < 0) + return retval; + + smbus_version = retval; + rmi_dbg(RMI_DEBUG_XPORT, &client->dev, "Smbus version is %d", + smbus_version); + + if (smbus_version != 2) { + dev_err(&client->dev, "Unrecognized SMB version %d.\n", + smbus_version); + return -ENODEV; + } + + i2c_set_clientdata(client, rmi_smb); + + retval = rmi_register_transport_device(&rmi_smb->xport); + if (retval) { + dev_err(&client->dev, "Failed to register transport driver at 0x%.2X.\n", + client->addr); + i2c_set_clientdata(client, NULL); + return retval; + } + + dev_info(&client->dev, "registered rmi smb driver at %#04x.\n", + client->addr); + return 0; + +} + +static int rmi_smb_remove(struct i2c_client *client) +{ + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); + + rmi_unregister_transport_device(&rmi_smb->xport); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int rmi_smb_suspend(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); + int ret; + + ret = rmi_driver_suspend(rmi_smb->xport.rmi_dev); + if (ret) + dev_warn(dev, "Failed to suspend device: %d\n", ret); + + return ret; +} +#endif + +#ifdef CONFIG_PM +static int rmi_smb_runtime_suspend(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); + int ret; + + ret = rmi_driver_suspend(rmi_smb->xport.rmi_dev); + if (ret) + dev_warn(dev, "Failed to suspend device: %d\n", ret); + + return 0; +} + +static int rmi_smb_runtime_resume(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); + int ret; + + ret = rmi_driver_resume(rmi_smb->xport.rmi_dev); + if (ret) + dev_warn(dev, "Failed to resume device: %d\n", ret); + + return 0; +} +#endif + +static const struct dev_pm_ops rmi_smb_pm = { + SET_SYSTEM_SLEEP_PM_OPS(rmi_smb_suspend, NULL) + SET_RUNTIME_PM_OPS(rmi_smb_runtime_suspend, rmi_smb_runtime_resume, + NULL) +}; + +static int rmi_smb_resume(struct device *dev) +{ + struct i2c_client *client = container_of(dev, struct i2c_client, dev); + struct rmi_smb_xport *rmi_smb = i2c_get_clientdata(client); + struct rmi_device *rmi_dev = rmi_smb->xport.rmi_dev; + int ret; + + rmi_smb_reset(&rmi_smb->xport, 0); + + rmi_reset(rmi_dev); + + ret = rmi_driver_resume(rmi_smb->xport.rmi_dev); + if (ret) + dev_warn(dev, "Failed to resume device: %d\n", ret); + + return 0; +} + +static const struct i2c_device_id rmi_id[] = { + { "rmi4_smbus", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, rmi_id); + +static struct i2c_driver rmi_smb_driver = { + .driver = { + .owner = THIS_MODULE, + .name = "rmi4_smbus", + .pm = &rmi_smb_pm, + .resume = rmi_smb_resume, + }, + .id_table = rmi_id, + .probe = rmi_smb_probe, + .remove = rmi_smb_remove, + .alert = rmi_smb_alert, +}; + +module_i2c_driver(rmi_smb_driver); + +MODULE_AUTHOR("Andrew Duggan <aduggan@synaptics.com>"); +MODULE_AUTHOR("Benjamin Tissoires <benjamin.tissoires@redhat.com>"); +MODULE_DESCRIPTION("RMI4 SMBus driver"); +MODULE_LICENSE("GPL");