@@ -42,6 +42,8 @@ Optional properties:
- snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists
in GUSB2PHYCFG, specify that USB2 PHY doesn't provide
a free-running PHY clock.
+ - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power
+ from P0 to P1/P2/P3 without delay.
- snps,phyif-utmi-quirk: when set core will set phyif UTMI+ interface.
- snps,phyif-utmi: the value to configure the core to support a UTMI+ PHY
with an 8- or 16-bit interface. Value 0 select 8-bit
@@ -449,6 +449,9 @@ static int dwc3_phy_setup(struct dwc3 *dwc)
if (dwc->dis_u3_susphy_quirk)
reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
+ if (dwc->dis_del_phy_power_chg_quirk)
+ reg &= ~DWC3_GUSB3PIPECTL_DEPOCHANGE;
+
dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
@@ -943,6 +946,8 @@ static int dwc3_probe(struct platform_device *pdev)
"snps,dis_rxdet_inp3_quirk");
dwc->dis_u2_freeclk_exists_quirk = device_property_read_bool(dev,
"snps,dis-u2-freeclk-exists-quirk");
+ dwc->dis_del_phy_power_chg_quirk = device_property_read_bool(dev,
+ "snps,dis-del-phy-power-chg-quirk");
dwc->phyif_utmi_quirk = device_property_read_bool(dev,
"snps,phyif-utmi-quirk");
device_property_read_u8(dev, "snps,phyif-utmi",
@@ -809,6 +809,8 @@ struct dwc3_scratchpad_array {
* @dis_u2_freeclk_exists_quirk : set if we clear u2_freeclk_exists
* in GUSB2PHYCFG, specify that USB2 PHY doesn't
* provide a free-running PHY clock.
+ * @dis_del_phy_power_chg_quirk: set if we disable delay phy power
+ * change quirk.
* @phyif_utmi_quirk: set if we enable phyif UTMI+ quirk
* @phyif_utmi: UTMI+ PHY interface value
* 0 - 8 bits
@@ -957,6 +959,7 @@ struct dwc3 {
unsigned dis_enblslpm_quirk:1;
unsigned dis_rxdet_inp3_quirk:1;
unsigned dis_u2_freeclk_exists_quirk:1;
+ unsigned dis_del_phy_power_chg_quirk:1;
unsigned phyif_utmi_quirk:1;
unsigned phyif_utmi:1;
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit, which specifies whether disable delay PHY power change from P0 to P1/P2/P3 when link state changing from U0 to U1/U2/U3 respectively. Signed-off-by: William Wu <william.wu@rock-chips.com> --- Changes in v6: - use '-' instead of '_' in dts (Rob Herring) Changes in v5: - None Changes in v4: - rebase on top of balbi testing/next, remove pdata (balbi) Changes in v3: - None Changes in v2: - None Documentation/devicetree/bindings/usb/dwc3.txt | 2 ++ drivers/usb/dwc3/core.c | 5 +++++ drivers/usb/dwc3/core.h | 3 +++ 3 files changed, 10 insertions(+)