Message ID | 1472820817-21874-1-git-send-email-andrei.pistirica@microchip.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
Hi Andrei, Adding Richard Cochran for PTP. On Fri, Sep 2, 2016 at 6:23 PM, Andrei Pistirica <andrei.pistirica@microchip.com> wrote: > From: Harini Katakam <harinik@xilinx.com> > > Cadence GEM provides a 102 bit time counter with 48 bits for seconds, > 30 bits for nsecs and 24 bits for sub-nsecs to control 1588 timestamping. > > This patch does the following: > - Registers to ptp clock framework > - Timer initialization is done by writing time of day to the timer counter. > - ns increment register is programmed as NSEC_PER_SEC/TSU_CLK. > For a 24 bit subns precision, the subns increment equals > remainder of (NS_PER_SEC/TSU_CLK) * (2^24). > - HW time stamp capabilities are advertised via ethtool and macb ioctl is > updated accordingly. > - Timestamps are obtained from the TX/RX PTP event/PEER registers. > The timestamp obtained thus is updated in skb for upper layers to access. > - The drivers register functions with ptp to perform time and frequency > adjustment. > - Time adjustment is done by writing to the 1558_ADJUST register. > The controller will read the delta in this register and update the timer > counter register. Alternatively, for large time offset adjustments, > the driver reads the secs and nsecs counter values, adds/subtracts the > delta and updates the timer counter. > - Frequency adjustment is not directly supported by this IP. > addend is the initial value ns increment and similarly addendesub. > The ppb (parts per billion) provided is used as > ns_incr = addend +/- (ppb/rate). > Similarly the remainder of the above is used to populate subns increment. > In case the ppb requested is negative AND subns adjustment greater than > the addendsub, ns_incr is reduced by 1 and subns_incr is adjusted in > positive accordingly. > > Signed-off-by: Harini Katakam <harinik@xilinx.com> > Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com> > --- > This patch is based on original Harini's patch, implemented in a > separate file to ease the review/maintanance and integration with > other platforms (e.g. Zynq Ultrascale+ MPSoC). > Feature was tested on SAMA5D2 platform using ptp4l v1.6 from linuxptp > project and also with ptpd2 version 2.3.1. PTP was tested over > IPv4,IPv6 and 802.3 protocols. > > Hariani, please let me know if you are ok with this patch, and if you > want to be stated as author/signed-off? > Thanks for the patch. It seems ok. I'm making some changes on top of this, especially in your second patch for picking RX timestamp, since that is handled from indication in the BD for ZynqMP. Regards, Harini
I have some issues with this patch... On Fri, Sep 02, 2016 at 02:53:36PM +0200, Andrei Pistirica wrote: > - Frequency adjustment is not directly supported by this IP. > addend is the initial value ns increment and similarly addendesub. > The ppb (parts per billion) provided is used as > ns_incr = addend +/- (ppb/rate). > Similarly the remainder of the above is used to populate subns increment. > In case the ppb requested is negative AND subns adjustment greater than > the addendsub, ns_incr is reduced by 1 and subns_incr is adjusted in > positive accordingly. This makes no sense. If you cannot adjust the frequency, then you must implement a timecounter/cyclecounter and do in software. > diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h > index 3f385ab..8c3779d 100644 > --- a/drivers/net/ethernet/cadence/macb.h > +++ b/drivers/net/ethernet/cadence/macb.h > @@ -10,6 +10,12 @@ > #ifndef _MACB_H > #define _MACB_H > > +#include <linux/net_tstamp.h> > +#include <linux/ptp_clock.h> > +#include <linux/ptp_clock_kernel.h> > +#include <linux/skbuff.h> > +#include <linux/timecounter.h> Here in the header file, you only need ptp_clock_kernel.h. You don't need all the others here. Move them to the .c file, but only if really needed. (timecounter.h isn't used, now is it?) > @@ -129,6 +135,20 @@ > #define GEM_RXIPCCNT 0x01a8 /* IP header Checksum Error Counter */ > #define GEM_RXTCPCCNT 0x01ac /* TCP Checksum Error Counter */ > #define GEM_RXUDPCCNT 0x01b0 /* UDP Checksum Error Counter */ > +#define GEM_TISUBN 0x01bc /* 1588 Timer Increment Sub-ns */ This regsiter does not exist. Looking at Zynq-7000 AP SoC Technical Reference Manual UG585 (v1.10) February 23, 2015 starting on page 1273 we see: udp_csum_errors 0x000001B0 32 ro 0x00000000 UDP checksum error timer_strobe_s 0x000001C8 32 rw 0x00000000 1588 timer sync strobe seconds timer_strobe_ns 0x000001CC 32 mixed 0x00000000 1588 timer sync strobe nanoseconds timer_s 0x000001D0 32 rw 0x00000000 1588 timer seconds timer_ns 0x000001D4 32 mixed 0x00000000 1588 timer nanoseconds timer_adjust 0x000001D8 32 mixed 0x00000000 1588 timer adjust timer_incr 0x000001DC 32 mixed 0x00000000 1588 timer increment There is no register at 0x1BC. > +#define GEM_TSH 0x01c0 /* 1588 Timer Seconds High */ This one doesn't exist either. What is going on here? > +#define GEM_TSL 0x01d0 /* 1588 Timer Seconds Low */ > +#define GEM_TN 0x01d4 /* 1588 Timer Nanoseconds */ > +#define GEM_TA 0x01d8 /* 1588 Timer Adjust */ > +#define GEM_TI 0x01dc /* 1588 Timer Increment */ > +#define GEM_EFTSL 0x01e0 /* PTP Event Frame Tx Seconds Low */ > +#define GEM_EFTN 0x01e4 /* PTP Event Frame Tx Nanoseconds */ > +#define GEM_EFRSL 0x01e8 /* PTP Event Frame Rx Seconds Low */ > +#define GEM_EFRN 0x01ec /* PTP Event Frame Rx Nanoseconds */ > +#define GEM_PEFTSL 0x01f0 /* PTP Peer Event Frame Tx Secs Low */ > +#define GEM_PEFTN 0x01f4 /* PTP Peer Event Frame Tx Ns */ > +#define GEM_PEFRSL 0x01f8 /* PTP Peer Event Frame Rx Sec Low */ > +#define GEM_PEFRN 0x01fc /* PTP Peer Event Frame Rx Ns */ BTW, it is really annoying that you invent new register names. Why can't you use the names from the TRM? > +#ifdef CONFIG_MACB_USE_HWSTAMP > +void macb_ptp_init(struct net_device *ndev); > +#else > +void macb_ptp_init(struct net_device *ndev) { } This should be static inline. > +#endif > diff --git a/drivers/net/ethernet/cadence/macb_ptp.c b/drivers/net/ethernet/cadence/macb_ptp.c > new file mode 100644 > index 0000000..6d6a6ec > --- /dev/null > +++ b/drivers/net/ethernet/cadence/macb_ptp.c > @@ -0,0 +1,224 @@ > +/* > + * PTP 1588 clock for SAMA5D2 platform. > + * > + * Copyright (C) 2015 Xilinx Inc. > + * Copyright (C) 2016 Microchip Technology > + * > + * Authors: Harini Katakam <harinik@xilinx.com> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +#include <linux/clk.h> > +#include <linux/device.h> > +#include <linux/etherdevice.h> > +#include <linux/platform_device.h> > +#include <linux/time64.h> > +#include <linux/ptp_classify.h> > +#include <linux/if_ether.h> > +#include <linux/if_vlan.h> > + > +#include "macb.h" > + > +#define GMAC_TIMER_NAME "gmac-ptp" > + > +static inline void macb_tsu_get_time(struct macb *bp, struct timespec64 *ts) > +{ > + u64 sech, secl; > + > + /* get GEM internal time */ > + sech = gem_readl(bp, TSH); > + secl = gem_readl(bp, TSL); Does reading TSH latch the time? The TRM is silent about that, and most other designs latch on reading the LSB. > + ts->tv_sec = (sech << 32) | secl; > + ts->tv_nsec = gem_readl(bp, TN); > +} > + > +static inline void macb_tsu_set_time(struct macb *bp, > + const struct timespec64 *ts) > +{ > + u32 ns, sech, secl; > + s64 word_mask = 0xffffffff; > + > + sech = (u32)ts->tv_sec; > + secl = (u32)ts->tv_sec; > + ns = ts->tv_nsec; > + if (ts->tv_sec > word_mask) > + sech = (ts->tv_sec >> 32); > + > + /* set GEM internal time */ Writing three registers is supposed to be one operation, and yet you have no mutex or spinlock to protect against concurrent settime calls. > + gem_writel(bp, TSH, sech); > + gem_writel(bp, TSL, secl); > + gem_writel(bp, TN, ns); Also, how does the HW behave here? Latch on TN write? > +} > + > +static int macb_ptp_adjfreq(struct ptp_clock_info *ptp, s32 ppb) > +{ > + struct macb *bp = container_of(ptp, struct macb, ptp_caps); > + unsigned long rate = bp->tsu_rate; > + u64 adjsub; > + u32 addend, addendsub, diff, rem, diffsub, subnsreg; > + bool neg_adj = false; > + > + if (ppb < 0) { > + neg_adj = true; > + ppb = -ppb; > + } > + > + addend = bp->ns_incr; > + addendsub = bp->subns_incr; > + > + diff = div_u64_rem(ppb, rate, &rem); One ... > + addend = neg_adj ? addend - diff : addend + diff; > + > + if (rem) { > + adjsub = rem; > + /* Multiple by 2^24 as subns field is 24 bits */ > + adjsub = adjsub << 24; > + > + diffsub = div_u64(adjsub, rate); ... Two ... > + } else { > + diffsub = 0; > + } > + > + if (neg_adj && (diffsub > addendsub)) { > + addend -= 1; > + rem = (NSEC_PER_SEC - rem); > + neg_adj = false; > + > + adjsub = rem; > + adjsub = adjsub << 24; > + diffsub = div_u64(adjsub, rate); Three. You need three 64 bit divisions? There must be a better way. If I guess correctly, the nsincr/subnsincr value is added to the device's time on every clock. So scaling these effectively adjusts the frequency. Here is an idea for you. You have a 24 bit fractional field. Combine that with 8 bits of whole nanoseconds to form one 32 tuning word. Restrict the nanoseconds to 8 bits in the setup code. (8 bits allows input clocks down to 4 MHz.) Multiply the tuning word by the 32 ppb variable, keeping the 64 bit result. Divide the result by 10^9 and that gives you the delta to add to (or subtract from) the nominal tuning word. See gianfar.c for an example. > + } > + > + addendsub = neg_adj ? addendsub - diffsub : addendsub + diffsub; > + /* RegBit[15:0] = Subns[23:8]; RegBit[31:24] = Subns[7:0] */ > + subnsreg = ((addendsub & GEM_SUBNSINCL_MASK) << GEM_SUBNSINCL_SHFT) | > + ((addendsub & GEM_SUBNSINCH_MASK) >> GEM_SUBNSINCH_SHFT); > + > + gem_writel(bp, TISUBN, subnsreg); > + gem_writel(bp, TI, GEM_BF(NSINCR, addend)); > + > + return 0; > +} Thanks, Richard
Hi, On Tue, Sep 6, 2016 at 9:18 PM, Richard Cochran <richardcochran@gmail.com> wrote: > <snip> >> +#define GEM_TISUBN 0x01bc /* 1588 Timer Increment Sub-ns */ > > This regsiter does not exist. Looking at > > Zynq-7000 AP SoC Technical Reference Manual > UG585 (v1.10) February 23, 2015 > > starting on page 1273 we see: > > udp_csum_errors 0x000001B0 32 ro 0x00000000 UDP checksum error > timer_strobe_s 0x000001C8 32 rw 0x00000000 1588 timer sync strobe seconds > timer_strobe_ns 0x000001CC 32 mixed 0x00000000 1588 timer sync strobe nanoseconds > timer_s 0x000001D0 32 rw 0x00000000 1588 timer seconds > timer_ns 0x000001D4 32 mixed 0x00000000 1588 timer nanoseconds > timer_adjust 0x000001D8 32 mixed 0x00000000 1588 timer adjust > timer_incr 0x000001DC 32 mixed 0x00000000 1588 timer increment > > There is no register at 0x1BC. > >> +#define GEM_TSH 0x01c0 /* 1588 Timer Seconds High */ > > This one doesn't exist either. What is going on here? I cant be sure of the version of Cadence GEM used in SAMA5D2 but these registers (sub ns increments alteast) only exist in the IP version used in Zynq Ultrascale+ MPSoC. <snip> >> + /* get GEM internal time */ >> + sech = gem_readl(bp, TSH); >> + secl = gem_readl(bp, TSL); > > Does reading TSH latch the time? The TRM is silent about that, and > most other designs latch on reading the LSB. No, it does not latch the time. When doing a read + adjust + write, this will mean there's room for some error. Although when writing, the write to MSB and LSB registers was made atomic. This bug fix came only in the most recent version of the IP, am afraid. Regards, Harini
On Thu, Sep 08, 2016 at 10:22:43AM +0530, Harini Katakam wrote: > I cant be sure of the version of Cadence GEM used in SAMA5D2 > but these registers (sub ns increments alteast) only exist in > the IP version used in Zynq Ultrascale+ MPSoC. Then you need to find a way to make sure the driver only binds to the correct silicon. Thanks, Richard
On Thu, Sep 08, 2016 at 10:22:43AM +0530, Harini Katakam wrote: > >> + /* get GEM internal time */ > >> + sech = gem_readl(bp, TSH); > >> + secl = gem_readl(bp, TSL); > > > > Does reading TSH latch the time? The TRM is silent about that, and > > most other designs latch on reading the LSB. > > No, it does not latch the time. > When doing a read + adjust + write, this will > mean there's room for some error. It also means that you will have to handle when the TSL value overflows into TSH. That means reading TSH twice, once before and once after reading TSL and retrying if needed. The code as written above will produce apparent jumps backwards in time, whenever the overflow occurs between the two read operations. Thanks, Richard
On 06.09.2016 17:48, Richard Cochran wrote: > > I have some issues with this patch... > > On Fri, Sep 02, 2016 at 02:53:36PM +0200, Andrei Pistirica wrote: > >> - Frequency adjustment is not directly supported by this IP. >> addend is the initial value ns increment and similarly addendesub. >> The ppb (parts per billion) provided is used as >> ns_incr = addend +/- (ppb/rate). >> Similarly the remainder of the above is used to populate subns increment. >> In case the ppb requested is negative AND subns adjustment greater than >> the addendsub, ns_incr is reduced by 1 and subns_incr is adjusted in >> positive accordingly. > > This makes no sense. If you cannot adjust the frequency, then you > must implement a timecounter/cyclecounter and do in software. > >> diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h >> index 3f385ab..8c3779d 100644 >> --- a/drivers/net/ethernet/cadence/macb.h >> +++ b/drivers/net/ethernet/cadence/macb.h >> @@ -10,6 +10,12 @@ >> #ifndef _MACB_H >> #define _MACB_H >> >> +#include <linux/net_tstamp.h> >> +#include <linux/ptp_clock.h> >> +#include <linux/ptp_clock_kernel.h> >> +#include <linux/skbuff.h> >> +#include <linux/timecounter.h> > > Here in the header file, you only need ptp_clock_kernel.h. You don't > need all the others here. Move them to the .c file, but only if > really needed. (timecounter.h isn't used, now is it?) Ack. Except timecounter.h, I need these headers for ptp_clock and ptp_clock_info parameters from struct macb. > >> @@ -129,6 +135,20 @@ >> #define GEM_RXIPCCNT 0x01a8 /* IP header Checksum Error Counter */ >> #define GEM_RXTCPCCNT 0x01ac /* TCP Checksum Error Counter */ >> #define GEM_RXUDPCCNT 0x01b0 /* UDP Checksum Error Counter */ > >> +#define GEM_TISUBN 0x01bc /* 1588 Timer Increment Sub-ns */ > > This regsiter does not exist. Looking at > > Zynq-7000 AP SoC Technical Reference Manual > UG585 (v1.10) February 23, 2015 > > starting on page 1273 we see: > > udp_csum_errors 0x000001B0 32 ro 0x00000000 UDP checksum error > timer_strobe_s 0x000001C8 32 rw 0x00000000 1588 timer sync strobe seconds > timer_strobe_ns 0x000001CC 32 mixed 0x00000000 1588 timer sync strobe nanoseconds > timer_s 0x000001D0 32 rw 0x00000000 1588 timer seconds > timer_ns 0x000001D4 32 mixed 0x00000000 1588 timer nanoseconds > timer_adjust 0x000001D8 32 mixed 0x00000000 1588 timer adjust > timer_incr 0x000001DC 32 mixed 0x00000000 1588 timer increment > > There is no register at 0x1BC. > For this feature I've used the following reference manual: http://www.atmel.com/Images/Atmel-11267-32-bit-Cortex-A5-Microcontroller-SAMA5D2_Datasheet.pdf In section 37.8 (page 980) there is: "588 Timer Increment Sub-nanoseconds Register GMAC_TISUBN Read/Write", detailed in section 37.8.92. I kept the naming convention used in the entire header. >> +#define GEM_TSH 0x01c0 /* 1588 Timer Seconds High */ > > This one doesn't exist either. What is going on here? > >> +#define GEM_TSL 0x01d0 /* 1588 Timer Seconds Low */ >> +#define GEM_TN 0x01d4 /* 1588 Timer Nanoseconds */ >> +#define GEM_TA 0x01d8 /* 1588 Timer Adjust */ >> +#define GEM_TI 0x01dc /* 1588 Timer Increment */ >> +#define GEM_EFTSL 0x01e0 /* PTP Event Frame Tx Seconds Low */ >> +#define GEM_EFTN 0x01e4 /* PTP Event Frame Tx Nanoseconds */ >> +#define GEM_EFRSL 0x01e8 /* PTP Event Frame Rx Seconds Low */ >> +#define GEM_EFRN 0x01ec /* PTP Event Frame Rx Nanoseconds */ >> +#define GEM_PEFTSL 0x01f0 /* PTP Peer Event Frame Tx Secs Low */ >> +#define GEM_PEFTN 0x01f4 /* PTP Peer Event Frame Tx Ns */ >> +#define GEM_PEFRSL 0x01f8 /* PTP Peer Event Frame Rx Sec Low */ >> +#define GEM_PEFRN 0x01fc /* PTP Peer Event Frame Rx Ns */ > > BTW, it is really annoying that you invent new register names. Why > can't you use the names from the TRM? All these registers are found in the document mentioned above. > >> +#ifdef CONFIG_MACB_USE_HWSTAMP >> +void macb_ptp_init(struct net_device *ndev); >> +#else >> +void macb_ptp_init(struct net_device *ndev) { } > > This should be static inline. Ack. I will update this properly. > >> +#endif > >> diff --git a/drivers/net/ethernet/cadence/macb_ptp.c b/drivers/net/ethernet/cadence/macb_ptp.c >> new file mode 100644 >> index 0000000..6d6a6ec >> --- /dev/null >> +++ b/drivers/net/ethernet/cadence/macb_ptp.c >> @@ -0,0 +1,224 @@ >> +/* >> + * PTP 1588 clock for SAMA5D2 platform. >> + * >> + * Copyright (C) 2015 Xilinx Inc. >> + * Copyright (C) 2016 Microchip Technology >> + * >> + * Authors: Harini Katakam <harinik@xilinx.com> >> + * >> + * This file is licensed under the terms of the GNU General Public >> + * License version 2. This program is licensed "as is" without any >> + * warranty of any kind, whether express or implied. >> + */ >> + >> +#include <linux/clk.h> >> +#include <linux/device.h> >> +#include <linux/etherdevice.h> >> +#include <linux/platform_device.h> >> +#include <linux/time64.h> >> +#include <linux/ptp_classify.h> >> +#include <linux/if_ether.h> >> +#include <linux/if_vlan.h> >> + >> +#include "macb.h" >> + >> +#define GMAC_TIMER_NAME "gmac-ptp" >> + >> +static inline void macb_tsu_get_time(struct macb *bp, struct timespec64 *ts) >> +{ >> + u64 sech, secl; >> + >> + /* get GEM internal time */ >> + sech = gem_readl(bp, TSH); >> + secl = gem_readl(bp, TSL); > > Does reading TSH latch the time? The TRM is silent about that, and > most other designs latch on reading the LSB. > >> + ts->tv_sec = (sech << 32) | secl; >> + ts->tv_nsec = gem_readl(bp, TN); >> +} >> + >> +static inline void macb_tsu_set_time(struct macb *bp, >> + const struct timespec64 *ts) >> +{ >> + u32 ns, sech, secl; >> + s64 word_mask = 0xffffffff; >> + >> + sech = (u32)ts->tv_sec; >> + secl = (u32)ts->tv_sec; >> + ns = ts->tv_nsec; >> + if (ts->tv_sec > word_mask) >> + sech = (ts->tv_sec >> 32); >> + >> + /* set GEM internal time */ > > Writing three registers is supposed to be one operation, and yet you > have no mutex or spinlock to protect against concurrent settime calls. Ack. I will add a spinlock. > >> + gem_writel(bp, TSH, sech); >> + gem_writel(bp, TSL, secl); >> + gem_writel(bp, TN, ns); > > Also, how does the HW behave here? Latch on TN write? > >> +} >> + >> +static int macb_ptp_adjfreq(struct ptp_clock_info *ptp, s32 ppb) >> +{ >> + struct macb *bp = container_of(ptp, struct macb, ptp_caps); >> + unsigned long rate = bp->tsu_rate; >> + u64 adjsub; >> + u32 addend, addendsub, diff, rem, diffsub, subnsreg; >> + bool neg_adj = false; >> + >> + if (ppb < 0) { >> + neg_adj = true; >> + ppb = -ppb; >> + } >> + >> + addend = bp->ns_incr; >> + addendsub = bp->subns_incr; >> + >> + diff = div_u64_rem(ppb, rate, &rem); > > One ... > >> + addend = neg_adj ? addend - diff : addend + diff; >> + >> + if (rem) { >> + adjsub = rem; >> + /* Multiple by 2^24 as subns field is 24 bits */ >> + adjsub = adjsub << 24; >> + >> + diffsub = div_u64(adjsub, rate); > > ... Two ... > >> + } else { >> + diffsub = 0; >> + } >> + >> + if (neg_adj && (diffsub > addendsub)) { >> + addend -= 1; >> + rem = (NSEC_PER_SEC - rem); >> + neg_adj = false; >> + >> + adjsub = rem; >> + adjsub = adjsub << 24; >> + diffsub = div_u64(adjsub, rate); > > Three. You need three 64 bit divisions? There must be a better way. > > If I guess correctly, the nsincr/subnsincr value is added to the > device's time on every clock. So scaling these effectively adjusts > the frequency. Here is an idea for you. > > You have a 24 bit fractional field. Combine that with 8 bits of whole > nanoseconds to form one 32 tuning word. Restrict the nanoseconds to 8 > bits in the setup code. (8 bits allows input clocks down to 4 MHz.) > > Multiply the tuning word by the 32 ppb variable, keeping the 64 bit > result. Divide the result by 10^9 and that gives you the delta to add > to (or subtract from) the nominal tuning word. > > See gianfar.c for an example. Ack. This code was taken with respect from Harini's first patch: https://lkml.org/lkml/2015/9/11/92. I can add an additional patch to take care of this on top of Harini's patch. > >> + } >> + >> + addendsub = neg_adj ? addendsub - diffsub : addendsub + diffsub; >> + /* RegBit[15:0] = Subns[23:8]; RegBit[31:24] = Subns[7:0] */ >> + subnsreg = ((addendsub & GEM_SUBNSINCL_MASK) << GEM_SUBNSINCL_SHFT) | >> + ((addendsub & GEM_SUBNSINCH_MASK) >> GEM_SUBNSINCH_SHFT); >> + >> + gem_writel(bp, TISUBN, subnsreg); >> + gem_writel(bp, TI, GEM_BF(NSINCR, addend)); >> + >> + return 0; >> +} > > Thanks, > Richard > Thanks, Andrei
diff --git a/drivers/net/ethernet/cadence/Kconfig b/drivers/net/ethernet/cadence/Kconfig index f0bcb15..ebbc65f 100644 --- a/drivers/net/ethernet/cadence/Kconfig +++ b/drivers/net/ethernet/cadence/Kconfig @@ -29,6 +29,14 @@ config MACB support for the MACB/GEM chip. To compile this driver as a module, choose M here: the module - will be called macb. + will be called cadence-macb. + +config MACB_USE_HWSTAMP + bool "Use IEEE 1588 hwstamp" + depends on MACB + default y + select PTP_1588_CLOCK + ---help--- + Enable IEEE 1588 Precision Time Protocol (PTP) support for MACB. endif # NET_CADENCE diff --git a/drivers/net/ethernet/cadence/Makefile b/drivers/net/ethernet/cadence/Makefile index 91f79b1..4402d42 100644 --- a/drivers/net/ethernet/cadence/Makefile +++ b/drivers/net/ethernet/cadence/Makefile @@ -2,4 +2,10 @@ # Makefile for the Atmel network device drivers. # -obj-$(CONFIG_MACB) += macb.o +cadence-macb-y := macb.o + +ifeq ($(CONFIG_MACB_USE_HWSTAMP),y) +cadence-macb-y += macb_ptp.o +endif + +obj-$(CONFIG_MACB) += cadence-macb.o diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h index 3f385ab..8c3779d 100644 --- a/drivers/net/ethernet/cadence/macb.h +++ b/drivers/net/ethernet/cadence/macb.h @@ -10,6 +10,12 @@ #ifndef _MACB_H #define _MACB_H +#include <linux/net_tstamp.h> +#include <linux/ptp_clock.h> +#include <linux/ptp_clock_kernel.h> +#include <linux/skbuff.h> +#include <linux/timecounter.h> + #define MACB_GREGS_NBR 16 #define MACB_GREGS_VERSION 2 #define MACB_MAX_QUEUES 8 @@ -129,6 +135,20 @@ #define GEM_RXIPCCNT 0x01a8 /* IP header Checksum Error Counter */ #define GEM_RXTCPCCNT 0x01ac /* TCP Checksum Error Counter */ #define GEM_RXUDPCCNT 0x01b0 /* UDP Checksum Error Counter */ +#define GEM_TISUBN 0x01bc /* 1588 Timer Increment Sub-ns */ +#define GEM_TSH 0x01c0 /* 1588 Timer Seconds High */ +#define GEM_TSL 0x01d0 /* 1588 Timer Seconds Low */ +#define GEM_TN 0x01d4 /* 1588 Timer Nanoseconds */ +#define GEM_TA 0x01d8 /* 1588 Timer Adjust */ +#define GEM_TI 0x01dc /* 1588 Timer Increment */ +#define GEM_EFTSL 0x01e0 /* PTP Event Frame Tx Seconds Low */ +#define GEM_EFTN 0x01e4 /* PTP Event Frame Tx Nanoseconds */ +#define GEM_EFRSL 0x01e8 /* PTP Event Frame Rx Seconds Low */ +#define GEM_EFRN 0x01ec /* PTP Event Frame Rx Nanoseconds */ +#define GEM_PEFTSL 0x01f0 /* PTP Peer Event Frame Tx Secs Low */ +#define GEM_PEFTN 0x01f4 /* PTP Peer Event Frame Tx Ns */ +#define GEM_PEFRSL 0x01f8 /* PTP Peer Event Frame Rx Sec Low */ +#define GEM_PEFRN 0x01fc /* PTP Peer Event Frame Rx Ns */ #define GEM_DCFG1 0x0280 /* Design Config 1 */ #define GEM_DCFG2 0x0284 /* Design Config 2 */ #define GEM_DCFG3 0x0288 /* Design Config 3 */ @@ -171,6 +191,7 @@ #define MACB_NCR_TPF_SIZE 1 #define MACB_TZQ_OFFSET 12 /* Transmit zero quantum pause frame */ #define MACB_TZQ_SIZE 1 +#define MACB_SRTSM_OFFSET 15 /* Bitfields in NCFGR */ #define MACB_SPD_OFFSET 0 /* Speed */ @@ -312,6 +333,36 @@ #define MACB_PFR_SIZE 1 #define MACB_PTZ_OFFSET 13 /* Enable pause time zero interrupt */ #define MACB_PTZ_SIZE 1 +#define MACB_PFTR_OFFSET 14 /* Pause Frame Transmitted */ +#define MACB_PFTR_SIZE 1 +#define MACB_DRQFR_OFFSET 18 /* PTP Delay Request Frame Received */ +#define MACB_DRQFR_SIZE 1 +#define MACB_SFR_OFFSET 19 /* PTP Sync Frame Received */ +#define MACB_SFR_SIZE 1 +#define MACB_DRQFT_OFFSET 20 /* PTP Delay Request Frame Transmitted */ +#define MACB_DRQFT_SIZE 1 +#define MACB_SFT_OFFSET 21 /* PTP Sync Frame Transmitted */ +#define MACB_SFT_SIZE 1 +#define MACB_PDRQFR_OFFSET 22 /* PDelay Request Frame Received */ +#define MACB_PDRQFR_SIZE 1 +#define MACB_PDRSFR_OFFSET 23 /* PDelay Response Frame Received */ +#define MACB_PDRSFR_SIZE 1 +#define MACB_PDRQFT_OFFSET 24 /* PDelay Request Frame Transmitted */ +#define MACB_PDRQFT_SIZE 1 +#define MACB_PDRSFT_OFFSET 25 /* PDelay Response Frame Transmitted */ +#define MACB_PDRSFT_SIZE 1 +#define MACB_SRI_OFFSET 26 /* TSU Seconds Register Increment */ +#define MACB_SRI_SIZE 1 +#define MACB_WOL_OFFSET 28 /* Wake On LAN */ +#define MACB_WOL_SIZE 1 + +/* Timer increment fields */ +#define MACB_TI_CNS_OFFSET 0 +#define MACB_TI_CNS_SIZE 8 +#define MACB_TI_ACNS_OFFSET 8 +#define MACB_TI_ACNS_SIZE 8 +#define MACB_TI_NIT_OFFSET 16 +#define MACB_TI_NIT_SIZE 8 /* Bitfields in MAN */ #define MACB_DATA_OFFSET 0 /* data */ @@ -375,6 +426,20 @@ #define GEM_TX_PKT_BUFF_OFFSET 21 #define GEM_TX_PKT_BUFF_SIZE 1 +/* Bitfields in 1588INCRSUBNS */ +#define GEM_SUBNSINCL_SHFT 24 +#define GEM_SUBNSINCL_MASK 0xFF +#define GEM_SUBNSINCH_SHFT 8 +#define GEM_SUBNSINCH_MASK 0xFFFF00 + +/* Bitfields in 1588INCRNS */ +#define GEM_NSINCR_OFFSET 0 +#define GEM_NSINCR_SIZE 8 + +/* Bitfields in 1588ADJ */ +#define GEM_ADDSUB_OFFSET 31 +#define GEM_ADDSUB_SIZE 1 + /* Constants for CLK */ #define MACB_CLK_DIV8 0 #define MACB_CLK_DIV16 1 @@ -840,8 +905,25 @@ struct macb { unsigned int rx_frm_len_mask; unsigned int jumbo_max_len; + +#ifdef CONFIG_MACB_USE_HWSTAMP + unsigned int hwts_tx_en; + unsigned int hwts_rx_en; + unsigned int tsu_rate; + + struct ptp_clock *ptp_clock; + struct ptp_clock_info ptp_caps; + unsigned int ns_incr; + unsigned int subns_incr; +#endif }; +#ifdef CONFIG_MACB_USE_HWSTAMP +void macb_ptp_init(struct net_device *ndev); +#else +void macb_ptp_init(struct net_device *ndev) { } +#endif + static inline bool macb_is_gem(struct macb *bp) { return !!(bp->caps & MACB_CAPS_MACB_IS_GEM); diff --git a/drivers/net/ethernet/cadence/macb_ptp.c b/drivers/net/ethernet/cadence/macb_ptp.c new file mode 100644 index 0000000..6d6a6ec --- /dev/null +++ b/drivers/net/ethernet/cadence/macb_ptp.c @@ -0,0 +1,224 @@ +/* + * PTP 1588 clock for SAMA5D2 platform. + * + * Copyright (C) 2015 Xilinx Inc. + * Copyright (C) 2016 Microchip Technology + * + * Authors: Harini Katakam <harinik@xilinx.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include <linux/clk.h> +#include <linux/device.h> +#include <linux/etherdevice.h> +#include <linux/platform_device.h> +#include <linux/time64.h> +#include <linux/ptp_classify.h> +#include <linux/if_ether.h> +#include <linux/if_vlan.h> + +#include "macb.h" + +#define GMAC_TIMER_NAME "gmac-ptp" + +static inline void macb_tsu_get_time(struct macb *bp, struct timespec64 *ts) +{ + u64 sech, secl; + + /* get GEM internal time */ + sech = gem_readl(bp, TSH); + secl = gem_readl(bp, TSL); + + ts->tv_sec = (sech << 32) | secl; + ts->tv_nsec = gem_readl(bp, TN); +} + +static inline void macb_tsu_set_time(struct macb *bp, + const struct timespec64 *ts) +{ + u32 ns, sech, secl; + s64 word_mask = 0xffffffff; + + sech = (u32)ts->tv_sec; + secl = (u32)ts->tv_sec; + ns = ts->tv_nsec; + if (ts->tv_sec > word_mask) + sech = (ts->tv_sec >> 32); + + /* set GEM internal time */ + gem_writel(bp, TSH, sech); + gem_writel(bp, TSL, secl); + gem_writel(bp, TN, ns); +} + +static int macb_ptp_adjfreq(struct ptp_clock_info *ptp, s32 ppb) +{ + struct macb *bp = container_of(ptp, struct macb, ptp_caps); + unsigned long rate = bp->tsu_rate; + u64 adjsub; + u32 addend, addendsub, diff, rem, diffsub, subnsreg; + bool neg_adj = false; + + if (ppb < 0) { + neg_adj = true; + ppb = -ppb; + } + + addend = bp->ns_incr; + addendsub = bp->subns_incr; + + diff = div_u64_rem(ppb, rate, &rem); + addend = neg_adj ? addend - diff : addend + diff; + + if (rem) { + adjsub = rem; + /* Multiple by 2^24 as subns field is 24 bits */ + adjsub = adjsub << 24; + + diffsub = div_u64(adjsub, rate); + } else { + diffsub = 0; + } + + if (neg_adj && (diffsub > addendsub)) { + addend -= 1; + rem = (NSEC_PER_SEC - rem); + neg_adj = false; + + adjsub = rem; + adjsub = adjsub << 24; + diffsub = div_u64(adjsub, rate); + } + + addendsub = neg_adj ? addendsub - diffsub : addendsub + diffsub; + /* RegBit[15:0] = Subns[23:8]; RegBit[31:24] = Subns[7:0] */ + subnsreg = ((addendsub & GEM_SUBNSINCL_MASK) << GEM_SUBNSINCL_SHFT) | + ((addendsub & GEM_SUBNSINCH_MASK) >> GEM_SUBNSINCH_SHFT); + + gem_writel(bp, TISUBN, subnsreg); + gem_writel(bp, TI, GEM_BF(NSINCR, addend)); + + return 0; +} + +static int macb_ptp_adjtime(struct ptp_clock_info *ptp, s64 delta) +{ + struct macb *bp = container_of(ptp, struct macb, ptp_caps); + struct timespec64 now, then = ns_to_timespec64(delta); + u32 adj, sign = 0; + + if (delta < 0) { + delta = -delta; + sign = 1; + } + + if (delta > 0x3FFFFFFF) { + macb_tsu_get_time(bp, &now); + + if (sign) + now = timespec64_sub(now, then); + else + now = timespec64_add(now, then); + + macb_tsu_set_time(bp, (const struct timespec64 *)&now); + } else { + adj = delta; + if (sign) + adj |= GEM_BIT(ADDSUB); + + gem_writel(bp, TA, adj); + } + + return 0; +} + +static int macb_ptp_gettime(struct ptp_clock_info *ptp, + struct timespec64 *ts) +{ + struct macb *bp = container_of(ptp, struct macb, ptp_caps); + + macb_tsu_get_time(bp, ts); + + return 0; +} + +static int macb_ptp_settime(struct ptp_clock_info *ptp, + const struct timespec64 *ts) +{ + struct macb *bp = container_of(ptp, struct macb, ptp_caps); + + macb_tsu_set_time(bp, ts); + + return 0; +} + +static int macb_ptp_enable(struct ptp_clock_info *ptp, + struct ptp_clock_request *rq, int on) +{ + return -EOPNOTSUPP; +} + +static struct ptp_clock_info macb_ptp_caps = { + .owner = THIS_MODULE, + .name = GMAC_TIMER_NAME, + .max_adj = 250000000, + .n_alarm = 0, + .n_ext_ts = 0, + .n_per_out = 0, + .n_pins = 0, + .pps = 0, + .adjfreq = macb_ptp_adjfreq, + .adjtime = macb_ptp_adjtime, + .gettime64 = macb_ptp_gettime, + .settime64 = macb_ptp_settime, + .enable = macb_ptp_enable, +}; + +void macb_ptp_init(struct net_device *ndev) +{ + struct macb *bp = netdev_priv(ndev); + struct timespec64 now; + u32 subnsreg, rem = 0; + u64 adj; + + bp->ptp_caps = macb_ptp_caps; + bp->tsu_rate = clk_get_rate(bp->pclk); + + gem_writel(bp, TSH, 0); + gem_writel(bp, TSL, 0); + gem_writel(bp, TN, 0); + getnstimeofday64(&now); + macb_tsu_set_time(bp, (const struct timespec64 *)&now); + + bp->ns_incr = div_u64_rem(NSEC_PER_SEC, bp->tsu_rate, &rem); + if (rem) { + adj = rem; + /* Multiply by 2^24 as subns register is 24 bits */ + adj = adj << 24; + + bp->subns_incr = div_u64(adj, bp->tsu_rate); + } else { + bp->subns_incr = 0; + } + + /* RegBit[15:0] = Subns[23:8]; RegBit[31:24] = Subns[7:0] */ + subnsreg = ((bp->subns_incr & GEM_SUBNSINCL_MASK) + << GEM_SUBNSINCL_SHFT) | + ((bp->subns_incr & GEM_SUBNSINCH_MASK) + >> GEM_SUBNSINCH_SHFT); + gem_writel(bp, TISUBN, subnsreg); + gem_writel(bp, TI, bp->ns_incr); + gem_writel(bp, TA, 0); + + bp->ptp_clock = ptp_clock_register(&bp->ptp_caps, NULL); + if (IS_ERR(&bp->ptp_clock)) { + bp->ptp_clock = NULL; + pr_err("ptp clock register failed\n"); + return; + } + + dev_info(&bp->pdev->dev, "%s ptp clock registered.\n", GMAC_TIMER_NAME); +}