| Message ID | 20161114131114.6053-1-hdegoede@redhat.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Mon, Nov 14, 2016 at 02:11:14PM +0100, Hans de Goede wrote: > commit ef3714fdbc8d ("Input: bma150 - extend chip detection for bma180"), > adds bma180 chip-ids to the input bma150 driver, assuming that they are > 100% compatible, but the bma180 is not compatible with the bma150 at all, > it has 14 bits resolution instead of 10, and it has quite different > control registers too. > > Treating the bma180 as a bma150 wrt its data registers will just result > in throwing away the lowest 4 bits, which is not too bad. But the ctrl > registers are a different story. Things happen to just work but supporting > that certainly does not make treating the bma180 the same as the bma150 > right. > > Since some setups depend on the evdev interface the bma150 driver offers > on top of the bma180, we cannot simply remove the bma180 ids. > > So this commit only removes the bma180 id when the bma180 iio driver, > which does treat the bma180 properly, is enabled. > > Cc: Dr. H. Nikolaus Schaller <hns@goldelico.com> > Signed-off-by: Hans de Goede <hdegoede@redhat.com> Applied, thank you. > --- > Changes in v2: > -Use IS_ENABLED(CONFIG_BMA180) instead of #ifdef CONFIG_BMA180 > --- > drivers/input/misc/bma150.c | 9 ++++++++- > 1 file changed, 8 insertions(+), 1 deletion(-) > > diff --git a/drivers/input/misc/bma150.c b/drivers/input/misc/bma150.c > index b0d4453..2124390 100644 > --- a/drivers/input/misc/bma150.c > +++ b/drivers/input/misc/bma150.c > @@ -538,8 +538,13 @@ static int bma150_probe(struct i2c_client *client, > return -EIO; > } > > + /* > + * Note if the IIO CONFIG_BMA180 driver is enabled we want to fail > + * the probe for the bma180 as the iio driver is preferred. > + */ > chip_id = i2c_smbus_read_byte_data(client, BMA150_CHIP_ID_REG); > - if (chip_id != BMA150_CHIP_ID && chip_id != BMA180_CHIP_ID) { > + if (chip_id != BMA150_CHIP_ID && > + (IS_ENABLED(CONFIG_BMA180) || chip_id != BMA180_CHIP_ID)) { > dev_err(&client->dev, "BMA150 chip id error: %d\n", chip_id); > return -EINVAL; > } > @@ -643,7 +648,9 @@ static UNIVERSAL_DEV_PM_OPS(bma150_pm, bma150_suspend, bma150_resume, NULL); > > static const struct i2c_device_id bma150_id[] = { > { "bma150", 0 }, > +#if !IS_ENABLED(CONFIG_BMA180) > { "bma180", 0 }, > +#endif > { "smb380", 0 }, > { "bma023", 0 }, > { } > -- > 2.9.3 >
diff --git a/drivers/input/misc/bma150.c b/drivers/input/misc/bma150.c index b0d4453..2124390 100644 --- a/drivers/input/misc/bma150.c +++ b/drivers/input/misc/bma150.c @@ -538,8 +538,13 @@ static int bma150_probe(struct i2c_client *client, return -EIO; } + /* + * Note if the IIO CONFIG_BMA180 driver is enabled we want to fail + * the probe for the bma180 as the iio driver is preferred. + */ chip_id = i2c_smbus_read_byte_data(client, BMA150_CHIP_ID_REG); - if (chip_id != BMA150_CHIP_ID && chip_id != BMA180_CHIP_ID) { + if (chip_id != BMA150_CHIP_ID && + (IS_ENABLED(CONFIG_BMA180) || chip_id != BMA180_CHIP_ID)) { dev_err(&client->dev, "BMA150 chip id error: %d\n", chip_id); return -EINVAL; } @@ -643,7 +648,9 @@ static UNIVERSAL_DEV_PM_OPS(bma150_pm, bma150_suspend, bma150_resume, NULL); static const struct i2c_device_id bma150_id[] = { { "bma150", 0 }, +#if !IS_ENABLED(CONFIG_BMA180) { "bma180", 0 }, +#endif { "smb380", 0 }, { "bma023", 0 }, { }
commit ef3714fdbc8d ("Input: bma150 - extend chip detection for bma180"), adds bma180 chip-ids to the input bma150 driver, assuming that they are 100% compatible, but the bma180 is not compatible with the bma150 at all, it has 14 bits resolution instead of 10, and it has quite different control registers too. Treating the bma180 as a bma150 wrt its data registers will just result in throwing away the lowest 4 bits, which is not too bad. But the ctrl registers are a different story. Things happen to just work but supporting that certainly does not make treating the bma180 the same as the bma150 right. Since some setups depend on the evdev interface the bma150 driver offers on top of the bma180, we cannot simply remove the bma180 ids. So this commit only removes the bma180 id when the bma180 iio driver, which does treat the bma180 properly, is enabled. Cc: Dr. H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- Changes in v2: -Use IS_ENABLED(CONFIG_BMA180) instead of #ifdef CONFIG_BMA180 --- drivers/input/misc/bma150.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)