| Message ID | 1479482261-19072-1-git-send-email-olimpiu@arcticsand.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Your subject should look something like [PATCH vX 0/Y] Where X is the number of times you've submitted this set. On Fri, 18 Nov 2016, Olimpiu Dejeu wrote: > Re-submission of arcxcnn backlight driver addressing the naming convention > concerns raised by Rob H. Note that all the device tree properties are > determined by the board design or IC EPROM settings and are not intended > to be user adjustable. This is a change log, not a commit log. Here is where you tell us about the patch. Read: Documentation/SubmittingPatches Documentation/SubmitChecklist ... before submitting again. > Acked-by: Rob Herring <robh@kernel.org> > Signed-off-by: Olimpiu Dejeu <olimpiu@arcticsand.com> > > --- In here (below the ---) you should have a change log which looks like this: v3 => v4: - The changes you made v2 => v3: - The changes you made v1 => v2: - The changes you made ... etc > .../bindings/leds/backlight/arcxcnn_bl.txt | 31 ++++++++++++++++++++++ > 1 file changed, 31 insertions(+) > create mode 100644 Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt > > diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt > new file mode 100644 > index 0000000..a7b6ff2 > --- /dev/null > +++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt > @@ -0,0 +1,33 @@ > +Binding for ArcticSand arc2c0608 LED driver > + > +Required properties: > +- compatible: should be "arc,arc2c0608" > +- reg: slave address > + > +Optional properties: > +- default-brightness: brightness value on boot, value from: 0-4095 > +- label: The name of the backlight device > + See Documentation/devicetree/bindings/leds/common.txt > +- led-sources: List of enabled channels from 0 to 5. > + See Documentation/devicetree/bindings/leds/common.txt > + > +- arc,led-config-0: setting for register ILED_CONFIG_0 > +- arc,led-config-1: setting for register ILED_CONFIG_1 > +- arc,dim-freq: PWM mode frequence setting (bits [3:0] used) > +- arc,comp-config: setting for register CONFIG_COMP > +- arc,filter-config: setting for register FILTER_CONFIG > +- arc,trim-config: setting for register IMAXTUNE > + > +Note: Optional properties not specified will default to values in IC EPROM > + > +Example: > + > +arc2c0608@30 { > + compatible = "arc,arc2c0608"; > + reg = <0x30>; > + default-brightness = <500>; > + label = "lcd-backlight"; > + linux,default-trigger = "backlight"; > + led-sources = <0 1 2 5>; > +}; > +
diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt new file mode 100644 index 0000000..a7b6ff2 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt @@ -0,0 +1,33 @@ +Binding for ArcticSand arc2c0608 LED driver + +Required properties: +- compatible: should be "arc,arc2c0608" +- reg: slave address + +Optional properties: +- default-brightness: brightness value on boot, value from: 0-4095 +- label: The name of the backlight device + See Documentation/devicetree/bindings/leds/common.txt +- led-sources: List of enabled channels from 0 to 5. + See Documentation/devicetree/bindings/leds/common.txt + +- arc,led-config-0: setting for register ILED_CONFIG_0 +- arc,led-config-1: setting for register ILED_CONFIG_1 +- arc,dim-freq: PWM mode frequence setting (bits [3:0] used) +- arc,comp-config: setting for register CONFIG_COMP +- arc,filter-config: setting for register FILTER_CONFIG +- arc,trim-config: setting for register IMAXTUNE + +Note: Optional properties not specified will default to values in IC EPROM + +Example: + +arc2c0608@30 { + compatible = "arc,arc2c0608"; + reg = <0x30>; + default-brightness = <500>; + label = "lcd-backlight"; + linux,default-trigger = "backlight"; + led-sources = <0 1 2 5>; +}; +