Message ID | 1484296978-18572-7-git-send-email-erin.lo@mediatek.com (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On 13/01/17 09:42, Erin Lo wrote: > From: Dawei Chien <dawei.chien@mediatek.com> > > Add thermal controller device nodes for MT2701. > > Signed-off-by: Dawei Chien <dawei.chien@mediatek.com> > Signed-off-by: Erin Lo <erin.lo@mediatek.com> > --- > arch/arm/boot/dts/mt2701.dtsi | 43 +++++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 43 insertions(+) > > diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi > index 3847f70..c43d5f8 100644 > --- a/arch/arm/boot/dts/mt2701.dtsi > +++ b/arch/arm/boot/dts/mt2701.dtsi > @@ -89,6 +89,36 @@ > clock-output-names = "rtc32k"; > }; > > + thermal-zones { > + cpu_thermal: cpu_thermal { > + polling-delay-passive = <1000>; /* milliseconds */ > + polling-delay = <1000>; /* milliseconds */ > + > + thermal-sensors = <&thermal 0>; > + sustainable-power = <1000>; > + > + trips { > + threshold: trip-point@0 { > + temperature = <68000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + > + target: trip-point@1 { > + temperature = <85000>; > + hysteresis = <2000>; > + type = "passive"; > + }; > + > + cpu_crit: cpu_crit@0 { > + temperature = <115000>; > + hysteresis = <2000>; > + type = "critical"; > + }; > + }; > + }; > + }; > + > timer { > compatible = "arm,armv7-timer"; > interrupt-parent = <&gic>; > @@ -270,6 +300,19 @@ > status = "disabled"; > }; > > + thermal: thermal@1100b000 { > + #thermal-sensor-cells = <0>; > + compatible = "mediatek,mt2701-thermal"; > + reg = <0 0x1100b000 0 0x1000>; > + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_LOW>; > + clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>; > + clock-names = "therm", "auxadc"; > + resets = <&pericfg 0x10>; should be MT2701_PERI_AUXADC_SW_RST, right? > + reset-names = "therm"; > + mediatek,auxadc = <&auxadc>; > + mediatek,apmixedsys = <&apmixedsys>; > + }; > + > nandc: nfi@1100d000 { > compatible = "mediatek,mt2701-nfc"; > reg = <0 0x1100d000 0 0x1000>; >
On Fri, 2017-01-13 at 16:27 +0100, Matthias Brugger wrote: > > On 13/01/17 09:42, Erin Lo wrote: > > From: Dawei Chien <dawei.chien@mediatek.com> > > > > Add thermal controller device nodes for MT2701. > > > > Signed-off-by: Dawei Chien <dawei.chien@mediatek.com> > > Signed-off-by: Erin Lo <erin.lo@mediatek.com> > > --- > > arch/arm/boot/dts/mt2701.dtsi | 43 +++++++++++++++++++++++++++++++++++++++++++ > > 1 file changed, 43 insertions(+) > > > > diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi > > index 3847f70..c43d5f8 100644 > > --- a/arch/arm/boot/dts/mt2701.dtsi > > +++ b/arch/arm/boot/dts/mt2701.dtsi > > @@ -89,6 +89,36 @@ > > clock-output-names = "rtc32k"; > > }; > > > > + thermal-zones { > > + cpu_thermal: cpu_thermal { > > + polling-delay-passive = <1000>; /* milliseconds */ > > + polling-delay = <1000>; /* milliseconds */ > > + > > + thermal-sensors = <&thermal 0>; > > + sustainable-power = <1000>; > > + > > + trips { > > + threshold: trip-point@0 { > > + temperature = <68000>; > > + hysteresis = <2000>; > > + type = "passive"; > > + }; > > + > > + target: trip-point@1 { > > + temperature = <85000>; > > + hysteresis = <2000>; > > + type = "passive"; > > + }; > > + > > + cpu_crit: cpu_crit@0 { > > + temperature = <115000>; > > + hysteresis = <2000>; > > + type = "critical"; > > + }; > > + }; > > + }; > > + }; > > + > > timer { > > compatible = "arm,armv7-timer"; > > interrupt-parent = <&gic>; > > @@ -270,6 +300,19 @@ > > status = "disabled"; > > }; > > > > + thermal: thermal@1100b000 { > > + #thermal-sensor-cells = <0>; > > + compatible = "mediatek,mt2701-thermal"; > > + reg = <0 0x1100b000 0 0x1000>; > > + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_LOW>; > > + clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>; > > + clock-names = "therm", "auxadc"; > > + resets = <&pericfg 0x10>; > > should be MT2701_PERI_AUXADC_SW_RST, right? > Thank you for your reminding, I didn't realize mt2701-resets.h upstream already, I would update on next version, thank you. resets = <&pericfg MT2701_PERI_AUXADC_SW_RST>; > > + reset-names = "therm"; > > + mediatek,auxadc = <&auxadc>; > > + mediatek,apmixedsys = <&apmixedsys>; > > + }; > > + > > nandc: nfi@1100d000 { > > compatible = "mediatek,mt2701-nfc"; > > reg = <0 0x1100d000 0 0x1000>; > >
On Mon, 2017-01-16 at 11:44 +0800, Dawei Chien wrote: > On Fri, 2017-01-13 at 16:27 +0100, Matthias Brugger wrote: > > > > On 13/01/17 09:42, Erin Lo wrote: > > > From: Dawei Chien <dawei.chien@mediatek.com> > > > > > > Add thermal controller device nodes for MT2701. > > > > > > Signed-off-by: Dawei Chien <dawei.chien@mediatek.com> > > > Signed-off-by: Erin Lo <erin.lo@mediatek.com> > > > --- > > > arch/arm/boot/dts/mt2701.dtsi | 43 +++++++++++++++++++++++++++++++++++++++++++ > > > 1 file changed, 43 insertions(+) > > > > > > diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi > > > index 3847f70..c43d5f8 100644 > > > --- a/arch/arm/boot/dts/mt2701.dtsi > > > +++ b/arch/arm/boot/dts/mt2701.dtsi > > > @@ -89,6 +89,36 @@ > > > clock-output-names = "rtc32k"; > > > }; > > > > > > + thermal-zones { > > > + cpu_thermal: cpu_thermal { > > > + polling-delay-passive = <1000>; /* milliseconds */ > > > + polling-delay = <1000>; /* milliseconds */ > > > + > > > + thermal-sensors = <&thermal 0>; > > > + sustainable-power = <1000>; > > > + > > > + trips { > > > + threshold: trip-point@0 { > > > + temperature = <68000>; > > > + hysteresis = <2000>; > > > + type = "passive"; > > > + }; > > > + > > > + target: trip-point@1 { > > > + temperature = <85000>; > > > + hysteresis = <2000>; > > > + type = "passive"; > > > + }; > > > + > > > + cpu_crit: cpu_crit@0 { > > > + temperature = <115000>; > > > + hysteresis = <2000>; > > > + type = "critical"; > > > + }; > > > + }; > > > + }; > > > + }; > > > + > > > timer { > > > compatible = "arm,armv7-timer"; > > > interrupt-parent = <&gic>; > > > @@ -270,6 +300,19 @@ > > > status = "disabled"; > > > }; > > > > > > + thermal: thermal@1100b000 { > > > + #thermal-sensor-cells = <0>; > > > + compatible = "mediatek,mt2701-thermal"; > > > + reg = <0 0x1100b000 0 0x1000>; > > > + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_LOW>; > > > + clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>; > > > + clock-names = "therm", "auxadc"; > > > + resets = <&pericfg 0x10>; > > > > should be MT2701_PERI_AUXADC_SW_RST, right? > > > Thank you for your reminding, I didn't realize mt2701-resets.h upstream > already, I would update on next version, thank you. > > resets = <&pericfg MT2701_PERI_AUXADC_SW_RST>; Actually, Should be MT2701_PERI_THERM_SW_RST. resets = <&pericfg MT2701_PERI_THERM_SW_RST>; > > > + reset-names = "therm"; > > > + mediatek,auxadc = <&auxadc>; > > > + mediatek,apmixedsys = <&apmixedsys>; > > > + }; > > > + > > > nandc: nfi@1100d000 { > > > compatible = "mediatek,mt2701-nfc"; > > > reg = <0 0x1100d000 0 0x1000>; > > > >
diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi index 3847f70..c43d5f8 100644 --- a/arch/arm/boot/dts/mt2701.dtsi +++ b/arch/arm/boot/dts/mt2701.dtsi @@ -89,6 +89,36 @@ clock-output-names = "rtc32k"; }; + thermal-zones { + cpu_thermal: cpu_thermal { + polling-delay-passive = <1000>; /* milliseconds */ + polling-delay = <1000>; /* milliseconds */ + + thermal-sensors = <&thermal 0>; + sustainable-power = <1000>; + + trips { + threshold: trip-point@0 { + temperature = <68000>; + hysteresis = <2000>; + type = "passive"; + }; + + target: trip-point@1 { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu_crit: cpu_crit@0 { + temperature = <115000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; + timer { compatible = "arm,armv7-timer"; interrupt-parent = <&gic>; @@ -270,6 +300,19 @@ status = "disabled"; }; + thermal: thermal@1100b000 { + #thermal-sensor-cells = <0>; + compatible = "mediatek,mt2701-thermal"; + reg = <0 0x1100b000 0 0x1000>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>; + clock-names = "therm", "auxadc"; + resets = <&pericfg 0x10>; + reset-names = "therm"; + mediatek,auxadc = <&auxadc>; + mediatek,apmixedsys = <&apmixedsys>; + }; + nandc: nfi@1100d000 { compatible = "mediatek,mt2701-nfc"; reg = <0 0x1100d000 0 0x1000>;