[V6,2/2] clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933

Commit Message

Marek Vasut Jan. 12, 2017, 1:03 a.m. UTC

Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These
chips have two clock inputs, XTAL or CLK, which are muxed into single
PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip
while the 5P49V5923 requires external XTAL.

The PLL feeds two fractional dividers. Each fractional divider feeds
output mux, which allows selecting between clock from the fractional
divider itself or from output mux on output N-1. In case of output
mux 0, the output N-1 is instead connected to the output from the mux
feeding the PLL.

The driver thus far supports only the 5P49V5923 and 5P49V5933, while
it should be easily extensible to the whole 5P49V59xx family of chips
as they are all pretty similar.

Signed-off-by: Marek Vasut <[e-mail]>
Cc: Michael Turquette <[e-mail]>
Cc: Stephen Boyd <[e-mail]>
Cc: Laurent Pinchart <[e-mail]>
Tested-by: Laurent Pinchart <[e-mail]>
Cc: [e-mail]
---
V2: - Drop address-cells and size-cells from the binding
    - Add clock-names to the binding
    - Drop vc5_input_names
    - Fix assortment of spelling mistakes
    - Switch div_frc and div_int datatype to uXX
    - Switch f_in to u32
    - Add missing remove
    - Define macros for handling XIN and CLKIN
    - Rework the FOD fractional divider calculation, this was wrong
      and made the output clock be off considerably under certain
      circumstances (when the fractional part was large).
V3: - Rework the MUX frequency recalculation and divider configration
      so that it fits into the clock framework
    - Add support for 5P49V5933 chip to lay groundwork for adding more
      chips easily.
    - Export the OUT0_SEL_I2CB output into the clock framework, so it
      can be accessed from DT as well. WARNING: This does change the
      bindings, clock0 is now the OUT0_SEL_I2CB, clock1 is OUT1 and
      clock2 is OUT2 (or OUT4 on the 5P49V5933).
    - Drop unnecessary caching of pin_*_name clock name and clk_hw structures
      in driver data.
    - Add missing MAINTAINERS entry
V4: - Support also 5P49V5923A by dropping the B from the bindings and
      code. According to the update notice, the chips are identical
      except for disabling the VCO monitoring, which is internal
      factory-defined bit and has no impact on silicon performance.
V5: - Make the CCF handle upstream clock enabling and disabling
    - Drop test for unsigned value reg being less than zero
    - Streamline vc5_map_index_to_output
V6: - Drop the error message from vc5_of_clk_get(), this will be
      reported by the core
---
 MAINTAINERS                   |   5 +
 drivers/clk/Kconfig           |  10 +
 drivers/clk/Makefile          |   1 +
 drivers/clk/clk-versaclock5.c | 793 ++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 809 insertions(+)
 create mode 100644 drivers/clk/clk-versaclock5.c

Comments

Laurent Pinchart Jan. 12, 2017, 1:35 a.m. UTC | #1

Hi Marek,

Thank you for the patch.

On Thursday 12 Jan 2017 02:03:24 Marek Vasut wrote:
> Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These
> chips have two clock inputs, XTAL or CLK, which are muxed into single
> PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip
> while the 5P49V5923 requires external XTAL.
> 
> The PLL feeds two fractional dividers. Each fractional divider feeds
> output mux, which allows selecting between clock from the fractional
> divider itself or from output mux on output N-1. In case of output
> mux 0, the output N-1 is instead connected to the output from the mux
> feeding the PLL.
> 
> The driver thus far supports only the 5P49V5923 and 5P49V5933, while
> it should be easily extensible to the whole 5P49V59xx family of chips
> as they are all pretty similar.
> 
> Signed-off-by: Marek Vasut <[e-mail]>
> Cc: Michael Turquette <[e-mail]>
> Cc: Stephen Boyd <[e-mail]>
> Cc: Laurent Pinchart <[e-mail]>
> Tested-by: Laurent Pinchart <[e-mail]>
> Cc: [e-mail]

Reviewed-by: Laurent Pinchart <[e-mail]>

> ---
> V2: - Drop address-cells and size-cells from the binding
>     - Add clock-names to the binding
>     - Drop vc5_input_names
>     - Fix assortment of spelling mistakes
>     - Switch div_frc and div_int datatype to uXX
>     - Switch f_in to u32
>     - Add missing remove
>     - Define macros for handling XIN and CLKIN
>     - Rework the FOD fractional divider calculation, this was wrong
>       and made the output clock be off considerably under certain
>       circumstances (when the fractional part was large).
> V3: - Rework the MUX frequency recalculation and divider configration
>       so that it fits into the clock framework
>     - Add support for 5P49V5933 chip to lay groundwork for adding more
>       chips easily.
>     - Export the OUT0_SEL_I2CB output into the clock framework, so it
>       can be accessed from DT as well. WARNING: This does change the
>       bindings, clock0 is now the OUT0_SEL_I2CB, clock1 is OUT1 and
>       clock2 is OUT2 (or OUT4 on the 5P49V5933).
>     - Drop unnecessary caching of pin_*_name clock name and clk_hw
> structures in driver data.
>     - Add missing MAINTAINERS entry
> V4: - Support also 5P49V5923A by dropping the B from the bindings and
>       code. According to the update notice, the chips are identical
>       except for disabling the VCO monitoring, which is internal
>       factory-defined bit and has no impact on silicon performance.
> V5: - Make the CCF handle upstream clock enabling and disabling
>     - Drop test for unsigned value reg being less than zero
>     - Streamline vc5_map_index_to_output
> V6: - Drop the error message from vc5_of_clk_get(), this will be
>       reported by the core
> ---
>  MAINTAINERS                   |   5 +
>  drivers/clk/Kconfig           |  10 +
>  drivers/clk/Makefile          |   1 +
>  drivers/clk/clk-versaclock5.c | 793 +++++++++++++++++++++++++++++++++++++++
>  4 files changed, 809 insertions(+)
>  create mode 100644 drivers/clk/clk-versaclock5.c

Stephen Boyd Jan. 21, 2017, 12:12 a.m. UTC | #2

On 01/12, Marek Vasut wrote:
> Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These
> chips have two clock inputs, XTAL or CLK, which are muxed into single
> PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip
> while the 5P49V5923 requires external XTAL.
> 
> The PLL feeds two fractional dividers. Each fractional divider feeds
> output mux, which allows selecting between clock from the fractional
> divider itself or from output mux on output N-1. In case of output
> mux 0, the output N-1 is instead connected to the output from the mux
> feeding the PLL.
> 
> The driver thus far supports only the 5P49V5923 and 5P49V5933, while
> it should be easily extensible to the whole 5P49V59xx family of chips
> as they are all pretty similar.
> 
> Signed-off-by: Marek Vasut <[e-mail]>
> Cc: Michael Turquette <[e-mail]>
> Cc: Stephen Boyd <[e-mail]>
> Cc: Laurent Pinchart <[e-mail]>
> Tested-by: Laurent Pinchart <[e-mail]>
> Cc: [e-mail]
> ---

Applied to clk-next

Marek Vasut Jan. 21, 2017, 12:14 a.m. UTC | #3

On 01/21/2017 01:12 AM, Stephen Boyd wrote:
> On 01/12, Marek Vasut wrote:
>> Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These
>> chips have two clock inputs, XTAL or CLK, which are muxed into single
>> PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip
>> while the 5P49V5923 requires external XTAL.
>>
>> The PLL feeds two fractional dividers. Each fractional divider feeds
>> output mux, which allows selecting between clock from the fractional
>> divider itself or from output mux on output N-1. In case of output
>> mux 0, the output N-1 is instead connected to the output from the mux
>> feeding the PLL.
>>
>> The driver thus far supports only the 5P49V5923 and 5P49V5933, while
>> it should be easily extensible to the whole 5P49V59xx family of chips
>> as they are all pretty similar.
>>
>> Signed-off-by: Marek Vasut <[e-mail]>
>> Cc: Michael Turquette <[e-mail]>
>> Cc: Stephen Boyd <[e-mail]>
>> Cc: Laurent Pinchart <[e-mail]>
>> Tested-by: Laurent Pinchart <[e-mail]>
>> Cc: [e-mail]
>> ---
> 
> Applied to clk-next
> 
Thank you :)

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 162d904d5cc3..890fc9e3c191 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6113,6 +6113,11 @@  S:	Maintained
 F:	drivers/mfd/lpc_ich.c
 F:	drivers/gpio/gpio-ich.c
 
+IDT VersaClock 5 CLOCK DRIVER
+M:	Marek Vasut <[e-mail]>
+S:	Maintained
+F:	drivers/clk/clk-versaclock5.c
+
 IDE SUBSYSTEM
 M:	"David S. Miller" <[e-mail]>
 L:	[e-mail]
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 6a8ac04bedeb..9160e6712067 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -198,6 +198,16 @@  config COMMON_CLK_OXNAS
 	---help---
 	  Support for the OXNAS SoC Family clocks.
 
+config COMMON_CLK_VC5
+	tristate "Clock driver for IDT VersaClock5 devices"
+	depends on I2C
+	depends on OF
+	select REGMAP_I2C
+	help
+	---help---
+	  This driver supports the IDT VersaClock5 programmable clock
+	  generator.
+
 source "drivers/clk/bcm/Kconfig"
 source "drivers/clk/hisilicon/Kconfig"
 source "drivers/clk/mediatek/Kconfig"
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 925081ec14c0..e0754d9fc2df 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -46,6 +46,7 @@  obj-$(CONFIG_ARCH_TANGO)		+= clk-tango4.o
 obj-$(CONFIG_CLK_TWL6040)		+= clk-twl6040.o
 obj-$(CONFIG_ARCH_U300)			+= clk-u300.o
 obj-$(CONFIG_ARCH_VT8500)		+= clk-vt8500.o
+obj-$(CONFIG_COMMON_CLK_VC5)		+= clk-versaclock5.o
 obj-$(CONFIG_COMMON_CLK_WM831X)		+= clk-wm831x.o
 obj-$(CONFIG_COMMON_CLK_XGENE)		+= clk-xgene.o
 
diff --git a/drivers/clk/clk-versaclock5.c b/drivers/clk/clk-versaclock5.c
new file mode 100644
index 000000000000..5859f2842951
--- /dev/null
+++ b/drivers/clk/clk-versaclock5.c
@@ -0,0 +1,793 @@ 
+/*
+ * Driver for IDT Versaclock 5
+ *
+ * Copyright (C) 2017 Marek Vasut <[e-mail]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Possible optimizations:
+ * - Use spread spectrum
+ * - Use integer divider in FOD if applicable
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/rational.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+/* VersaClock5 registers */
+#define VC5_OTP_CONTROL				0x00
+
+/* Factory-reserved register block */
+#define VC5_RSVD_DEVICE_ID			0x01
+#define VC5_RSVD_ADC_GAIN_7_0			0x02
+#define VC5_RSVD_ADC_GAIN_15_8			0x03
+#define VC5_RSVD_ADC_OFFSET_7_0			0x04
+#define VC5_RSVD_ADC_OFFSET_15_8		0x05
+#define VC5_RSVD_TEMPY				0x06
+#define VC5_RSVD_OFFSET_TBIN			0x07
+#define VC5_RSVD_GAIN				0x08
+#define VC5_RSVD_TEST_NP			0x09
+#define VC5_RSVD_UNUSED				0x0a
+#define VC5_RSVD_BANDGAP_TRIM_UP		0x0b
+#define VC5_RSVD_BANDGAP_TRIM_DN		0x0c
+#define VC5_RSVD_CLK_R_12_CLK_AMP_4		0x0d
+#define VC5_RSVD_CLK_R_34_CLK_AMP_4		0x0e
+#define VC5_RSVD_CLK_AMP_123			0x0f
+
+/* Configuration register block */
+#define VC5_PRIM_SRC_SHDN			0x10
+#define VC5_PRIM_SRC_SHDN_EN_XTAL		BIT(7)
+#define VC5_PRIM_SRC_SHDN_EN_CLKIN		BIT(6)
+#define VC5_PRIM_SRC_SHDN_SP			BIT(1)
+#define VC5_PRIM_SRC_SHDN_EN_GBL_SHDN		BIT(0)
+
+#define VC5_VCO_BAND				0x11
+#define VC5_XTAL_X1_LOAD_CAP			0x12
+#define VC5_XTAL_X2_LOAD_CAP			0x13
+#define VC5_REF_DIVIDER				0x15
+#define VC5_REF_DIVIDER_SEL_PREDIV2		BIT(7)
+#define VC5_REF_DIVIDER_REF_DIV(n)		((n) & 0x3f)
+
+#define VC5_VCO_CTRL_AND_PREDIV			0x16
+#define VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV	BIT(7)
+
+#define VC5_FEEDBACK_INT_DIV			0x17
+#define VC5_FEEDBACK_INT_DIV_BITS		0x18
+#define VC5_FEEDBACK_FRAC_DIV(n)		(0x19 + (n))
+#define VC5_RC_CONTROL0				0x1e
+#define VC5_RC_CONTROL1				0x1f
+/* Register 0x20 is factory reserved */
+
+/* Output divider control for divider 1,2,3,4 */
+#define VC5_OUT_DIV_CONTROL(idx)	(0x21 + ((idx) * 0x10))
+#define VC5_OUT_DIV_CONTROL_RESET	BIT(7)
+#define VC5_OUT_DIV_CONTROL_SELB_NORM	BIT(3)
+#define VC5_OUT_DIV_CONTROL_SEL_EXT	BIT(2)
+#define VC5_OUT_DIV_CONTROL_INT_MODE	BIT(1)
+#define VC5_OUT_DIV_CONTROL_EN_FOD	BIT(0)
+
+#define VC5_OUT_DIV_FRAC(idx, n)	(0x22 + ((idx) * 0x10) + (n))
+#define VC5_OUT_DIV_FRAC4_OD_SCEE	BIT(1)
+
+#define VC5_OUT_DIV_STEP_SPREAD(idx, n)	(0x26 + ((idx) * 0x10) + (n))
+#define VC5_OUT_DIV_SPREAD_MOD(idx, n)	(0x29 + ((idx) * 0x10) + (n))
+#define VC5_OUT_DIV_SKEW_INT(idx, n)	(0x2b + ((idx) * 0x10) + (n))
+#define VC5_OUT_DIV_INT(idx, n)		(0x2d + ((idx) * 0x10) + (n))
+#define VC5_OUT_DIV_SKEW_FRAC(idx)	(0x2f + ((idx) * 0x10))
+/* Registers 0x30, 0x40, 0x50 are factory reserved */
+
+/* Clock control register for clock 1,2 */
+#define VC5_CLK_OUTPUT_CFG(idx, n)	(0x60 + ((idx) * 0x2) + (n))
+#define VC5_CLK_OUTPUT_CFG1_EN_CLKBUF	BIT(0)
+
+#define VC5_CLK_OE_SHDN				0x68
+#define VC5_CLK_OS_SHDN				0x69
+
+#define VC5_GLOBAL_REGISTER			0x76
+#define VC5_GLOBAL_REGISTER_GLOBAL_RESET	BIT(5)
+
+/* PLL/VCO runs between 2.5 GHz and 3.0 GHz */
+#define VC5_PLL_VCO_MIN				2500000000UL
+#define VC5_PLL_VCO_MAX				3000000000UL
+
+/* VC5 Input mux settings */
+#define VC5_MUX_IN_XIN		BIT(0)
+#define VC5_MUX_IN_CLKIN	BIT(1)
+
+/* Supported IDT VC5 models. */
+enum vc5_model {
+	IDT_VC5_5P49V5923,
+	IDT_VC5_5P49V5933,
+};
+
+struct vc5_driver_data;
+
+struct vc5_hw_data {
+	struct clk_hw		hw;
+	struct vc5_driver_data	*vc5;
+	u32			div_int;
+	u32			div_frc;
+	unsigned int		num;
+};
+
+struct vc5_driver_data {
+	struct i2c_client	*client;
+	struct regmap		*regmap;
+	enum vc5_model		model;
+
+	struct clk		*pin_xin;
+	struct clk		*pin_clkin;
+	unsigned char		clk_mux_ins;
+	struct clk_hw		clk_mux;
+	struct vc5_hw_data	clk_pll;
+	struct vc5_hw_data	clk_fod[2];
+	struct vc5_hw_data	clk_out[3];
+};
+
+static const char * const vc5_mux_names[] = {
+	"mux"
+};
+
+static const char * const vc5_pll_names[] = {
+	"pll"
+};
+
+static const char * const vc5_fod_names[] = {
+	"fod0", "fod1", "fod2", "fod3",
+};
+
+static const char * const vc5_clk_out_names[] = {
+	"out0_sel_i2cb", "out1", "out2", "out3", "out4",
+};
+
+/*
+ * VersaClock5 i2c regmap
+ */
+static bool vc5_regmap_is_writeable(struct device *dev, unsigned int reg)
+{
+	/* Factory reserved regs, make them read-only */
+	if (reg <= 0xf)
+		return false;
+
+	/* Factory reserved regs, make them read-only */
+	if (reg == 0x14 || reg == 0x1c || reg == 0x1d)
+		return false;
+
+	return true;
+}
+
+static const struct regmap_config vc5_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.cache_type = REGCACHE_RBTREE,
+	.max_register = 0x76,
+	.writeable_reg = vc5_regmap_is_writeable,
+};
+
+/*
+ * VersaClock5 input multiplexer between XTAL and CLKIN divider
+ */
+static unsigned char vc5_mux_get_parent(struct clk_hw *hw)
+{
+	struct vc5_driver_data *vc5 =
+		container_of(hw, struct vc5_driver_data, clk_mux);
+	const u8 mask = VC5_PRIM_SRC_SHDN_EN_XTAL | VC5_PRIM_SRC_SHDN_EN_CLKIN;
+	unsigned int src;
+
+	regmap_read(vc5->regmap, VC5_PRIM_SRC_SHDN, &src);
+	src &= mask;
+
+	if (src == VC5_PRIM_SRC_SHDN_EN_XTAL)
+		return 0;
+
+	if (src == VC5_PRIM_SRC_SHDN_EN_CLKIN)
+		return 1;
+
+	dev_warn(&vc5->client->dev,
+		 "Invalid clock input configuration (%02x)\n", src);
+	return 0;
+}
+
+static int vc5_mux_set_parent(struct clk_hw *hw, u8 index)
+{
+	struct vc5_driver_data *vc5 =
+		container_of(hw, struct vc5_driver_data, clk_mux);
+	const u8 mask = VC5_PRIM_SRC_SHDN_EN_XTAL | VC5_PRIM_SRC_SHDN_EN_CLKIN;
+	u8 src;
+
+	if ((index > 1) || !vc5->clk_mux_ins)
+		return -EINVAL;
+
+	if (vc5->clk_mux_ins == (VC5_MUX_IN_CLKIN | VC5_MUX_IN_XIN)) {
+		if (index == 0)
+			src = VC5_PRIM_SRC_SHDN_EN_XTAL;
+		if (index == 1)
+			src = VC5_PRIM_SRC_SHDN_EN_CLKIN;
+	} else {
+		if (index != 0)
+			return -EINVAL;
+
+		if (vc5->clk_mux_ins == VC5_MUX_IN_XIN)
+			src = VC5_PRIM_SRC_SHDN_EN_XTAL;
+		if (vc5->clk_mux_ins == VC5_MUX_IN_CLKIN)
+			src = VC5_PRIM_SRC_SHDN_EN_CLKIN;
+	}
+
+	return regmap_update_bits(vc5->regmap, VC5_PRIM_SRC_SHDN, mask, src);
+}
+
+static unsigned long vc5_mux_recalc_rate(struct clk_hw *hw,
+					 unsigned long parent_rate)
+{
+	struct vc5_driver_data *vc5 =
+		container_of(hw, struct vc5_driver_data, clk_mux);
+	unsigned int prediv, div;
+
+	regmap_read(vc5->regmap, VC5_VCO_CTRL_AND_PREDIV, &prediv);
+
+	/* The bypass_prediv is set, PLL fed from Ref_in directly. */
+	if (prediv & VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV)
+		return parent_rate;
+
+	regmap_read(vc5->regmap, VC5_REF_DIVIDER, &div);
+
+	/* The Sel_prediv2 is set, PLL fed from prediv2 (Ref_in / 2) */
+	if (div & VC5_REF_DIVIDER_SEL_PREDIV2)
+		return parent_rate / 2;
+	else
+		return parent_rate / VC5_REF_DIVIDER_REF_DIV(div);
+}
+
+static long vc5_mux_round_rate(struct clk_hw *hw, unsigned long rate,
+			       unsigned long *parent_rate)
+{
+	unsigned long idiv;
+
+	/* PLL cannot operate with input clock above 50 MHz. */
+	if (rate > 50000000)
+		return -EINVAL;
+
+	/* CLKIN within range of PLL input, feed directly to PLL. */
+	if (*parent_rate <= 50000000)
+		return *parent_rate;
+
+	idiv = DIV_ROUND_UP(*parent_rate, rate);
+	if (idiv > 127)
+		return -EINVAL;
+
+	return *parent_rate / idiv;
+}
+
+static int vc5_mux_set_rate(struct clk_hw *hw, unsigned long rate,
+			    unsigned long parent_rate)
+{
+	struct vc5_driver_data *vc5 =
+		container_of(hw, struct vc5_driver_data, clk_mux);
+	unsigned long idiv;
+	u8 div;
+
+	/* CLKIN within range of PLL input, feed directly to PLL. */
+	if (parent_rate <= 50000000) {
+		regmap_update_bits(vc5->regmap, VC5_VCO_CTRL_AND_PREDIV,
+				   VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV,
+				   VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV);
+		regmap_update_bits(vc5->regmap, VC5_REF_DIVIDER, 0xff, 0x00);
+		return 0;
+	}
+
+	idiv = DIV_ROUND_UP(parent_rate, rate);
+
+	/* We have dedicated div-2 predivider. */
+	if (idiv == 2)
+		div = VC5_REF_DIVIDER_SEL_PREDIV2;
+	else
+		div = VC5_REF_DIVIDER_REF_DIV(idiv);
+
+	regmap_update_bits(vc5->regmap, VC5_REF_DIVIDER, 0xff, div);
+	regmap_update_bits(vc5->regmap, VC5_VCO_CTRL_AND_PREDIV,
+			   VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV, 0);
+
+	return 0;
+}
+
+static const struct clk_ops vc5_mux_ops = {
+	.set_parent	= vc5_mux_set_parent,
+	.get_parent	= vc5_mux_get_parent,
+	.recalc_rate	= vc5_mux_recalc_rate,
+	.round_rate	= vc5_mux_round_rate,
+	.set_rate	= vc5_mux_set_rate,
+};
+
+/*
+ * VersaClock5 PLL/VCO
+ */
+static unsigned long vc5_pll_recalc_rate(struct clk_hw *hw,
+					 unsigned long parent_rate)
+{
+	struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
+	struct vc5_driver_data *vc5 = hwdata->vc5;
+	u32 div_int, div_frc;
+	u8 fb[5];
+
+	regmap_bulk_read(vc5->regmap, VC5_FEEDBACK_INT_DIV, fb, 5);
+
+	div_int = (fb[0] << 4) | (fb[1] >> 4);
+	div_frc = (fb[2] << 16) | (fb[3] << 8) | fb[4];
+
+	/* The PLL divider has 12 integer bits and 24 fractional bits */
+	return (parent_rate * div_int) + ((parent_rate * div_frc) >> 24);
+}
+
+static long vc5_pll_round_rate(struct clk_hw *hw, unsigned long rate,
+			       unsigned long *parent_rate)
+{
+	struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
+	u32 div_int;
+	u64 div_frc;
+
+	if (rate < VC5_PLL_VCO_MIN)
+		rate = VC5_PLL_VCO_MIN;
+	if (rate > VC5_PLL_VCO_MAX)
+		rate = VC5_PLL_VCO_MAX;
+
+	/* Determine integer part, which is 12 bit wide */
+	div_int = rate / *parent_rate;
+	if (div_int > 0xfff)
+		rate = *parent_rate * 0xfff;
+
+	/* Determine best fractional part, which is 24 bit wide */
+	div_frc = rate % *parent_rate;
+	div_frc *= BIT(24) - 1;
+	do_div(div_frc, *parent_rate);
+
+	hwdata->div_int = div_int;
+	hwdata->div_frc = (u32)div_frc;
+
+	return (*parent_rate * div_int) + ((*parent_rate * div_frc) >> 24);
+}
+
+static int vc5_pll_set_rate(struct clk_hw *hw, unsigned long rate,
+			    unsigned long parent_rate)
+{
+	struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
+	struct vc5_driver_data *vc5 = hwdata->vc5;
+	u8 fb[5];
+
+	fb[0] = hwdata->div_int >> 4;
+	fb[1] = hwdata->div_int << 4;
+	fb[2] = hwdata->div_frc >> 16;
+	fb[3] = hwdata->div_frc >> 8;
+	fb[4] = hwdata->div_frc;
+
+	return regmap_bulk_write(vc5->regmap, VC5_FEEDBACK_INT_DIV, fb, 5);
+}
+
+static const struct clk_ops vc5_pll_ops = {
+	.recalc_rate	= vc5_pll_recalc_rate,
+	.round_rate	= vc5_pll_round_rate,
+	.set_rate	= vc5_pll_set_rate,
+};
+
+static unsigned long vc5_fod_recalc_rate(struct clk_hw *hw,
+					 unsigned long parent_rate)
+{
+	struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
+	struct vc5_driver_data *vc5 = hwdata->vc5;
+	/* VCO frequency is divided by two before entering FOD */
+	u32 f_in = parent_rate / 2;
+	u32 div_int, div_frc;
+	u8 od_int[2];
+	u8 od_frc[4];
+
+	regmap_bulk_read(vc5->regmap, VC5_OUT_DIV_INT(hwdata->num, 0),
+			 od_int, 2);
+	regmap_bulk_read(vc5->regmap, VC5_OUT_DIV_FRAC(hwdata->num, 0),
+			 od_frc, 4);
+
+	div_int = (od_int[0] << 4) | (od_int[1] >> 4);
+	div_frc = (od_frc[0] << 22) | (od_frc[1] << 14) |
+		  (od_frc[2] << 6) | (od_frc[3] >> 2);
+
+	/* The PLL divider has 12 integer bits and 30 fractional bits */
+	return div64_u64((u64)f_in << 24ULL, ((u64)div_int << 24ULL) + div_frc);
+}
+
+static long vc5_fod_round_rate(struct clk_hw *hw, unsigned long rate,
+			       unsigned long *parent_rate)
+{
+	struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
+	/* VCO frequency is divided by two before entering FOD */
+	u32 f_in = *parent_rate / 2;
+	u32 div_int;
+	u64 div_frc;
+
+	/* Determine integer part, which is 12 bit wide */
+	div_int = f_in / rate;
+	/*
+	 * WARNING: The clock chip does not output signal if the integer part
+	 *          of the divider is 0xfff and fractional part is non-zero.
+	 *          Clamp the divider at 0xffe to keep the code simple.
+	 */
+	if (div_int > 0xffe) {
+		div_int = 0xffe;
+		rate = f_in / div_int;
+	}
+
+	/* Determine best fractional part, which is 30 bit wide */
+	div_frc = f_in % rate;
+	div_frc <<= 24;
+	do_div(div_frc, rate);
+
+	hwdata->div_int = div_int;
+	hwdata->div_frc = (u32)div_frc;
+
+	return div64_u64((u64)f_in << 24ULL, ((u64)div_int << 24ULL) + div_frc);
+}
+
+static int vc5_fod_set_rate(struct clk_hw *hw, unsigned long rate,
+			    unsigned long parent_rate)
+{
+	struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
+	struct vc5_driver_data *vc5 = hwdata->vc5;
+	u8 data[14] = {
+		hwdata->div_frc >> 22, hwdata->div_frc >> 14,
+		hwdata->div_frc >> 6, hwdata->div_frc << 2,
+		0, 0, 0, 0, 0,
+		0, 0,
+		hwdata->div_int >> 4, hwdata->div_int << 4,
+		0
+	};
+
+	regmap_bulk_write(vc5->regmap, VC5_OUT_DIV_FRAC(hwdata->num, 0),
+			  data, 14);
+
+	/*
+	 * Toggle magic bit in undocumented register for unknown reason.
+	 * This is what the IDT timing commander tool does and the chip
+	 * datasheet somewhat implies this is needed, but the register
+	 * and the bit is not documented.
+	 */
+	regmap_update_bits(vc5->regmap, VC5_GLOBAL_REGISTER,
+			   VC5_GLOBAL_REGISTER_GLOBAL_RESET, 0);
+	regmap_update_bits(vc5->regmap, VC5_GLOBAL_REGISTER,
+			   VC5_GLOBAL_REGISTER_GLOBAL_RESET,
+			   VC5_GLOBAL_REGISTER_GLOBAL_RESET);
+	return 0;
+}
+
+static const struct clk_ops vc5_fod_ops = {
+	.recalc_rate	= vc5_fod_recalc_rate,
+	.round_rate	= vc5_fod_round_rate,
+	.set_rate	= vc5_fod_set_rate,
+};
+
+static int vc5_clk_out_prepare(struct clk_hw *hw)
+{
+	struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
+	struct vc5_driver_data *vc5 = hwdata->vc5;
+
+	/* Enable the clock buffer */
+	regmap_update_bits(vc5->regmap, VC5_CLK_OUTPUT_CFG(hwdata->num, 1),
+			   VC5_CLK_OUTPUT_CFG1_EN_CLKBUF,
+			   VC5_CLK_OUTPUT_CFG1_EN_CLKBUF);
+	return 0;
+}
+
+static void vc5_clk_out_unprepare(struct clk_hw *hw)
+{
+	struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
+	struct vc5_driver_data *vc5 = hwdata->vc5;
+
+	/* Enable the clock buffer */
+	regmap_update_bits(vc5->regmap, VC5_CLK_OUTPUT_CFG(hwdata->num, 1),
+			   VC5_CLK_OUTPUT_CFG1_EN_CLKBUF, 0);
+}
+
+static unsigned char vc5_clk_out_get_parent(struct clk_hw *hw)
+{
+	struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
+	struct vc5_driver_data *vc5 = hwdata->vc5;
+	const u8 mask = VC5_OUT_DIV_CONTROL_SELB_NORM |
+			VC5_OUT_DIV_CONTROL_SEL_EXT |
+			VC5_OUT_DIV_CONTROL_EN_FOD;
+	const u8 fodclkmask = VC5_OUT_DIV_CONTROL_SELB_NORM |
+			      VC5_OUT_DIV_CONTROL_EN_FOD;
+	const u8 extclk = VC5_OUT_DIV_CONTROL_SELB_NORM |
+			  VC5_OUT_DIV_CONTROL_SEL_EXT;
+	unsigned int src;
+
+	regmap_read(vc5->regmap, VC5_OUT_DIV_CONTROL(hwdata->num), &src);
+	src &= mask;
+
+	if ((src & fodclkmask) == VC5_OUT_DIV_CONTROL_EN_FOD)
+		return 0;
+
+	if (src == extclk)
+		return 1;
+
+	dev_warn(&vc5->client->dev,
+		 "Invalid clock output configuration (%02x)\n", src);
+	return 0;
+}
+
+static int vc5_clk_out_set_parent(struct clk_hw *hw, u8 index)
+{
+	struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
+	struct vc5_driver_data *vc5 = hwdata->vc5;
+	const u8 mask = VC5_OUT_DIV_CONTROL_RESET |
+			VC5_OUT_DIV_CONTROL_SELB_NORM |
+			VC5_OUT_DIV_CONTROL_SEL_EXT |
+			VC5_OUT_DIV_CONTROL_EN_FOD;
+	const u8 extclk = VC5_OUT_DIV_CONTROL_SELB_NORM |
+			  VC5_OUT_DIV_CONTROL_SEL_EXT;
+	u8 src = VC5_OUT_DIV_CONTROL_RESET;
+
+	if (index == 0)
+		src |= VC5_OUT_DIV_CONTROL_EN_FOD;
+	else
+		src |= extclk;
+
+	return regmap_update_bits(vc5->regmap, VC5_OUT_DIV_CONTROL(hwdata->num),
+				  mask, src);
+}
+
+static const struct clk_ops vc5_clk_out_ops = {
+	.prepare	= vc5_clk_out_prepare,
+	.unprepare	= vc5_clk_out_unprepare,
+	.set_parent	= vc5_clk_out_set_parent,
+	.get_parent	= vc5_clk_out_get_parent,
+};
+
+static struct clk_hw *vc5_of_clk_get(struct of_phandle_args *clkspec,
+				     void *data)
+{
+	struct vc5_driver_data *vc5 = data;
+	unsigned int idx = clkspec->args[0];
+
+	if (idx > 2)
+		return ERR_PTR(-EINVAL);
+
+	return &vc5->clk_out[idx].hw;
+}
+
+static int vc5_map_index_to_output(const enum vc5_model model,
+				   const unsigned int n)
+{
+	switch (model) {
+	case IDT_VC5_5P49V5933:
+		return (n == 0) ? 0 : 3;
+	case IDT_VC5_5P49V5923:
+	default:
+		return n;
+	}
+}
+
+static const struct of_device_id clk_vc5_of_match[];
+
+static int vc5_probe(struct i2c_client *client,
+		     const struct i2c_device_id *id)
+{
+	const struct of_device_id *of_id =
+		of_match_device(clk_vc5_of_match, &client->dev);
+	struct vc5_driver_data *vc5;
+	struct clk_init_data init;
+	const char *parent_names[2];
+	unsigned int n, idx;
+	int ret;
+
+	vc5 = devm_kzalloc(&client->dev, sizeof(*vc5), GFP_KERNEL);
+	if (vc5 == NULL)
+		return -ENOMEM;
+
+	i2c_set_clientdata(client, vc5);
+	vc5->client = client;
+	vc5->model = (enum vc5_model)of_id->data;
+
+	vc5->pin_xin = devm_clk_get(&client->dev, "xin");
+	if (PTR_ERR(vc5->pin_xin) == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	vc5->pin_clkin = devm_clk_get(&client->dev, "clkin");
+	if (PTR_ERR(vc5->pin_clkin) == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	vc5->regmap = devm_regmap_init_i2c(client, &vc5_regmap_config);
+	if (IS_ERR(vc5->regmap)) {
+		dev_err(&client->dev, "failed to allocate register map\n");
+		return PTR_ERR(vc5->regmap);
+	}
+
+	/* Register clock input mux */
+	memset(&init, 0, sizeof(init));
+
+	if (!IS_ERR(vc5->pin_xin)) {
+		vc5->clk_mux_ins |= VC5_MUX_IN_XIN;
+		parent_names[init.num_parents++] = __clk_get_name(vc5->pin_xin);
+	} else if (vc5->model == IDT_VC5_5P49V5933) {
+		/* IDT VC5 5P49V5933 has built-in oscilator. */
+		vc5->pin_xin = clk_register_fixed_rate(&client->dev,
+						       "internal-xtal", NULL,
+						       0, 25000000);
+		if (IS_ERR(vc5->pin_xin))
+			return PTR_ERR(vc5->pin_xin);
+		vc5->clk_mux_ins |= VC5_MUX_IN_XIN;
+		parent_names[init.num_parents++] = __clk_get_name(vc5->pin_xin);
+	}
+
+	if (!IS_ERR(vc5->pin_clkin)) {
+		vc5->clk_mux_ins |= VC5_MUX_IN_CLKIN;
+		parent_names[init.num_parents++] =
+			__clk_get_name(vc5->pin_clkin);
+	}
+
+	if (!init.num_parents) {
+		dev_err(&client->dev, "no input clock specified!\n");
+		return -EINVAL;
+	}
+
+	init.name = vc5_mux_names[0];
+	init.ops = &vc5_mux_ops;
+	init.flags = 0;
+	init.parent_names = parent_names;
+	vc5->clk_mux.init = &init;
+	ret = devm_clk_hw_register(&client->dev, &vc5->clk_mux);
+	if (ret) {
+		dev_err(&client->dev, "unable to register %s\n", init.name);
+		goto err_clk;
+	}
+
+	/* Register PLL */
+	memset(&init, 0, sizeof(init));
+	init.name = vc5_pll_names[0];
+	init.ops = &vc5_pll_ops;
+	init.flags = CLK_SET_RATE_PARENT;
+	init.parent_names = vc5_mux_names;
+	init.num_parents = 1;
+	vc5->clk_pll.num = 0;
+	vc5->clk_pll.vc5 = vc5;
+	vc5->clk_pll.hw.init = &init;
+	ret = devm_clk_hw_register(&client->dev, &vc5->clk_pll.hw);
+	if (ret) {
+		dev_err(&client->dev, "unable to register %s\n", init.name);
+		goto err_clk;
+	}
+
+	/* Register FODs */
+	for (n = 0; n < 2; n++) {
+		idx = vc5_map_index_to_output(vc5->model, n);
+		memset(&init, 0, sizeof(init));
+		init.name = vc5_fod_names[idx];
+		init.ops = &vc5_fod_ops;
+		init.flags = CLK_SET_RATE_PARENT;
+		init.parent_names = vc5_pll_names;
+		init.num_parents = 1;
+		vc5->clk_fod[n].num = idx;
+		vc5->clk_fod[n].vc5 = vc5;
+		vc5->clk_fod[n].hw.init = &init;
+		ret = devm_clk_hw_register(&client->dev, &vc5->clk_fod[n].hw);
+		if (ret) {
+			dev_err(&client->dev, "unable to register %s\n",
+				init.name);
+			goto err_clk;
+		}
+	}
+
+	/* Register MUX-connected OUT0_I2C_SELB output */
+	memset(&init, 0, sizeof(init));
+	init.name = vc5_clk_out_names[0];
+	init.ops = &vc5_clk_out_ops;
+	init.flags = CLK_SET_RATE_PARENT;
+	init.parent_names = vc5_mux_names;
+	init.num_parents = 1;
+	vc5->clk_out[0].num = idx;
+	vc5->clk_out[0].vc5 = vc5;
+	vc5->clk_out[0].hw.init = &init;
+	ret = devm_clk_hw_register(&client->dev, &vc5->clk_out[0].hw);
+	if (ret) {
+		dev_err(&client->dev, "unable to register %s\n",
+			init.name);
+		goto err_clk;
+	}
+
+	/* Register FOD-connected OUTx outputs */
+	for (n = 1; n < 3; n++) {
+		idx = vc5_map_index_to_output(vc5->model, n - 1);
+		parent_names[0] = vc5_fod_names[idx];
+		if (n == 1)
+			parent_names[1] = vc5_mux_names[0];
+		else
+			parent_names[1] = vc5_clk_out_names[n - 1];
+
+		memset(&init, 0, sizeof(init));
+		init.name = vc5_clk_out_names[idx + 1];
+		init.ops = &vc5_clk_out_ops;
+		init.flags = CLK_SET_RATE_PARENT;
+		init.parent_names = parent_names;
+		init.num_parents = 2;
+		vc5->clk_out[n].num = idx;
+		vc5->clk_out[n].vc5 = vc5;
+		vc5->clk_out[n].hw.init = &init;
+		ret = devm_clk_hw_register(&client->dev,
+					   &vc5->clk_out[n].hw);
+		if (ret) {
+			dev_err(&client->dev, "unable to register %s\n",
+				init.name);
+			goto err_clk;
+		}
+	}
+
+	ret = of_clk_add_hw_provider(client->dev.of_node, vc5_of_clk_get, vc5);
+	if (ret) {
+		dev_err(&client->dev, "unable to add clk provider\n");
+		goto err_clk;
+	}
+
+	return 0;
+
+err_clk:
+	if (vc5->model == IDT_VC5_5P49V5933)
+		clk_unregister_fixed_rate(vc5->pin_xin);
+	return ret;
+}
+
+static int vc5_remove(struct i2c_client *client)
+{
+	struct vc5_driver_data *vc5 = i2c_get_clientdata(client);
+
+	of_clk_del_provider(client->dev.of_node);
+
+	if (vc5->model == IDT_VC5_5P49V5933)
+		clk_unregister_fixed_rate(vc5->pin_xin);
+
+	return 0;
+}
+
+static const struct i2c_device_id vc5_id[] = {
+	{ "5p49v5923", .driver_data = IDT_VC5_5P49V5923 },
+	{ "5p49v5933", .driver_data = IDT_VC5_5P49V5933 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, vc5_id);
+
+static const struct of_device_id clk_vc5_of_match[] = {
+	{ .compatible = "idt,5p49v5923", .data = (void *)IDT_VC5_5P49V5923 },
+	{ .compatible = "idt,5p49v5933", .data = (void *)IDT_VC5_5P49V5933 },
+	{ },
+};
+
+MODULE_DEVICE_TABLE(of, clk_vc5_of_match);
+
+static struct i2c_driver vc5_driver = {
+	.driver = {
+		.name = "vc5",
+		.of_match_table = clk_vc5_of_match,
+	},
+	.probe		= vc5_probe,
+	.remove		= vc5_remove,
+	.id_table	= vc5_id,
+};
+
+module_i2c_driver(vc5_driver);
+
+MODULE_AUTHOR("Marek Vasut <[e-mail]>");
+MODULE_DESCRIPTION("IDT VersaClock 5 driver");
+MODULE_LICENSE("GPL");