diff mbox

[1/3] ARM: dts: Add support for phyCORE-AM335x PCM-953 carrier board

Message ID 1484831270-7251-1-git-send-email-t.remmet@phytec.de (mailing list archive)
State New, archived
Headers show

Commit Message

Teresa Remmet Jan. 19, 2017, 1:07 p.m. UTC
The phyCORE-AM335x development kit is a combination of the
phyCORE-AM335x SoM and a PCM-953 carrier board. The features
of the PCM-953 are:
* ETH phy on carrier board: 1x RGMII
* 1x CAN
* Up to 4x UART
* USB0 (otg)
* USB1 (host)
* SD slot
* User gpio-keys
* User LEDs

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
---
 .../devicetree/bindings/arm/omap/omap.txt          |   3 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/am335x-pcm-953.dtsi              | 303 +++++++++++++++++++++
 arch/arm/boot/dts/am335x-phycore-rdk.dts           |  27 ++
 4 files changed, 334 insertions(+)
 create mode 100644 arch/arm/boot/dts/am335x-pcm-953.dtsi
 create mode 100644 arch/arm/boot/dts/am335x-phycore-rdk.dts

Comments

Vladimir Zapolskiy Jan. 19, 2017, 2:24 p.m. UTC | #1
On 01/19/2017 03:07 PM, Teresa Remmet wrote:
> The phyCORE-AM335x development kit is a combination of the
> phyCORE-AM335x SoM and a PCM-953 carrier board. The features
> of the PCM-953 are:
> * ETH phy on carrier board: 1x RGMII
> * 1x CAN
> * Up to 4x UART
> * USB0 (otg)
> * USB1 (host)
> * SD slot
> * User gpio-keys
> * User LEDs
> 
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
> ---
>  .../devicetree/bindings/arm/omap/omap.txt          |   3 +
>  arch/arm/boot/dts/Makefile                         |   1 +
>  arch/arm/boot/dts/am335x-pcm-953.dtsi              | 303 +++++++++++++++++++++
>  arch/arm/boot/dts/am335x-phycore-rdk.dts           |  27 ++
>  4 files changed, 334 insertions(+)
>  create mode 100644 arch/arm/boot/dts/am335x-pcm-953.dtsi
>  create mode 100644 arch/arm/boot/dts/am335x-phycore-rdk.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
> index 05f95c3..8219b2c 100644
> --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
> +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
> @@ -151,6 +151,9 @@ Boards:
>  - AM335X SBC-T335 : single board computer, built around the Sitara AM3352/4
>    compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx"
>  
> +- AM335X phyCORE-AM335x: Development kit
> +  compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx"
> +
>  - OMAP5 EVM : Evaluation Module
>    compatible = "ti,omap5-evm", "ti,omap5"
>  
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7327250..dd71afe 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -573,6 +573,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
>  	am335x-lxm.dtb \
>  	am335x-nano.dtb \
>  	am335x-pepper.dtb \
> +	am335x-phycore-rdk.dtb \
>  	am335x-shc.dtb \
>  	am335x-sbc-t335.dtb \
>  	am335x-sl50.dtb \
> diff --git a/arch/arm/boot/dts/am335x-pcm-953.dtsi b/arch/arm/boot/dts/am335x-pcm-953.dtsi
> new file mode 100644
> index 0000000..54a171d
> --- /dev/null
> +++ b/arch/arm/boot/dts/am335x-pcm-953.dtsi
> @@ -0,0 +1,303 @@
> +/*
> + * Copyright (C) 2014-2017 Phytec Messtechnik GmbH
> + * Author: Wadim Egorov <w.egorov@phytec.de>
> + *	   Teresa Remmet <t.remmet@phytec.de>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "Phytec AM335x PCM-953";
> +	compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx";
> +
> +	user_leds: user_leds {
> +		compatible = "gpio-leds";
> +	};
> +
> +	user_buttons: user_buttons {
> +		compatible = "gpio-keys";
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";

Please drop "simple-bus" compatible, see http://www.spinics.net/lists/linux-usb/msg101497.html

> +
> +		vcc3v3: fixedregulator@1 {
> +			compatible = "regulator-fixed";
> +		};
> +
> +		vcc1v8: fixedregulator@2 {
> +			compatible = "regulator-fixed";
> +		};
> +	};
> +};
> +
> +/* CAN */
> +&am33xx_pinmux {

Which .dtsi file contains the referenced am33xx_pinmux device node?

You should include that file firstly, this is relevant to all other
references to device nodes used in this file.

> +	dcan1_pins: pinmux_dcan1 {
> +		pinctrl-single,pins = <
> +			AM33XX_IOPAD(0x980, PIN_OUTPUT_PULLUP | MUX_MODE2)	/* uart1_rxd.dcan1_tx_mux2 */
> +			AM33XX_IOPAD(0x984, PIN_INPUT_PULLUP | MUX_MODE2)	/* uart1_txd.dcan1_rx_mux2 */
> +		>;
> +	};
> +};
> +
> +&dcan1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&dcan1_pins>;
> +	status = "okay";
> +};
> +
> +/* Ethernet */
> +&am33xx_pinmux {
> +	ethernet1_pins: pinmux_ethernet1 {
> +		pinctrl-single,pins = <
> +			AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a0.rgmii2_tctl */
> +			AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a1.rgmii2_rctl */
> +			AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a2.rgmii2_td3 */
> +			AM33XX_IOPAD(0x84c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a3.rgmii2_td2 */
> +			AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a4.rgmii2_td1 */
> +			AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a5.rgmii2_td0 */
> +			AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a6.rgmii2_tclk */
> +			AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a7.rgmii2_rclk */
> +			AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a8.rgmii2_rd3 */
> +			AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a9.rgmii2_rd2 */
> +			AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a10.rgmii2_rd1 */
> +			AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a11.rgmii2_rd0 */
> +		>;
> +	};
> +};
> +
> +&cpsw_emac1 {
> +	phy-handle = <&phy1>;
> +	phy-mode = "rgmii-id";
> +	dual_emac_res_vlan = <2>;
> +	status = "okay";
> +};
> +
> +&davinci_mdio {
> +	phy1: ethernet-phy@1 {
> +		reg = <2>;

There is a mismatch between unit address and 'reg' property values.

> +
> +		/* Register 260 (104h) – RGMII Clock and Control Pad Skew */
> +		rxc-skew-ps = <1400>;
> +		rxdv-skew-ps = <0>;
> +		txc-skew-ps = <1400>;
> +		txen-skew-ps = <0>;
> +		/* Register 261 (105h) – RGMII RX Data Pad Skew */
> +		rxd3-skew-ps = <0>;
> +		rxd2-skew-ps = <0>;
> +		rxd1-skew-ps = <0>;
> +		rxd0-skew-ps = <0>;
> +		/* Register 262 (106h) – RGMII TX Data Pad Skew */
> +		txd3-skew-ps = <0>;
> +		txd2-skew-ps = <0>;
> +		txd1-skew-ps = <0>;
> +		txd0-skew-ps = <0>;
> +	};
> +};
> +
> +&mac {
> +	slaves = <2>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
> +	dual_emac;

It seems that TI has properties with underscores in the names, acked.

> +};
> +
> +/* Misc */
> +&am33xx_pinmux {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&cb_gpio_pins>;
> +
> +	cb_gpio_pins: pinmux_cb_gpio {
> +		pinctrl-single,pins = <
> +			AM33XX_IOPAD(0x968, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart0_ctsn.gpio1_8 */
> +			AM33XX_IOPAD(0x96c, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart0_rtsn.gpio1_9 */
> +		>;
> +	};
> +};
> +
> +/* MMC */
> +&am33xx_pinmux {
> +	mmc1_pins: pinmux_mmc1_pins {
> +		pinctrl-single,pins = <
> +			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat3.mmc0_dat3 */
> +			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat2.mmc0_dat2 */
> +			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat1.mmc0_dat1 */
> +			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat0.mmc0_dat0 */
> +			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_clk.mmc0_clk */
> +			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_cmd.mmc0_cmd */
> +			AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE7)	/* spi0_cs1.mmc0_sdcd */
> +		>;
> +	};
> +};
> +
> +&mmc1 {
> +	vmmc-supply = <&vcc3v3>;
> +	bus-width = <4>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc1_pins>;
> +	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
> +	status = "okay";
> +};
> +
> +/* Power */
> +&vcc3v3 {
> +	regulator-name = "vcc3v3";
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-boot-on;
> +};

Please add properties directly into vcc3v3 device node.

> +
> +&vcc1v8 {
> +	regulator-name = "vcc1v8";
> +	regulator-min-microvolt = <1800000>;
> +	regulator-max-microvolt = <1800000>;
> +	regulator-boot-on;
> +};
> +

Please add properties directly into vcc1v8 device node.

> +/* UARTs */
> +&am33xx_pinmux {
> +	uart0_pins: pinmux_uart0 {
> +		pinctrl-single,pins = <
> +			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
> +			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
> +		>;
> +	};
> +
> +	uart1_pins: pinmux_uart1 {
> +		pinctrl-single,pins = <
> +			AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart1_rxd.uart1_rxd */
> +			AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_txd.uart1_txd */
> +			AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0)		/* uart1_ctsn.uart1_ctsn */
> +			AM33XX_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_rtsn.uart1_rtsn */
> +		>;
> +	};
> +
> +	uart2_pins: pinmux_uart2 {
> +		pinctrl-single,pins = <
> +			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE1)	/* mii1_tx_clk.uart2_rxd */
> +			AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_rx_clk.uart2_txd */
> +		>;
> +	};
> +
> +	uart3_pins: pinmux_uart3 {
> +		pinctrl-single,pins = <
> +			AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1)	/* mii1_rxd3.uart3_rxd */
> +			AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxd2.uart3_txd */
> +		>;
> +	};
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pins>;
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart1_pins>;
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart2_pins>;
> +	status = "okay";
> +};
> +
> +&uart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart3_pins>;
> +	status = "okay";
> +};
> +
> +/* USB */
> +&cppi41dma {
> +	status = "okay";
> +};
> +
> +&usb_ctrl_mod {
> +	status = "okay";
> +};
> +
> +&usb {
> +	status = "okay";
> +};
> +
> +&usb0 {
> +	status = "okay";
> +};
> +
> +&usb0_phy {
> +	status = "okay";
> +};
> +
> +&usb1 {
> +	status = "okay";
> +	dr_mode = "host";
> +};
> +
> +&usb1_phy {
> +	status = "okay";
> +};
> +
> +/* User IO */
> +&am33xx_pinmux {
> +	user_buttons_pins: pinmux_user_buttons {
> +		pinctrl-single,pins = <
> +			AM33XX_IOPAD(0x9e4, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* emu0.gpio3_7 */
> +			AM33XX_IOPAD(0x9e8, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* emu1.gpio3_8 */
> +		>;
> +	};
> +
> +	user_leds_pins: pinmux_user_leds {
> +		pinctrl-single,pins = <
> +			AM33XX_IOPAD(0x880, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn1.gpio1_30 */
> +			AM33XX_IOPAD(0x884, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn2.gpio1_31 */
> +		>;
> +	};
> +};
> +
> +&user_buttons {

Please add properties directly into user_buttons device node.

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&user_buttons_pins>;
> +	status = "okay";

Please remove the redundant property above.

> +
> +	button@0 {
> +		label = "home";
> +		linux,code = <KEY_HOME>;
> +		gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
> +		gpio-key,wakeup;
> +	};
> +
> +	button@1 {
> +		label = "menu";
> +		linux,code = <KEY_MENU>;
> +		gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
> +		gpio-key,wakeup;
> +	};
> +};
> +
> +&user_leds {

Please add properties directly into user_leds device node.

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&user_leds_pins>;
> +	status = "okay";

Please remove the redundant property above.

> +
> +	green {
> +		label = "green:user";
> +		gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> +		linux,default-trigger = "gpio";
> +		default-state = "on";
> +	};
> +
> +	yellow {
> +		label = "yellow:user";
> +		gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
> +		linux,default-trigger = "gpio";
> +		default-state = "on";
> +	};
> +};
> diff --git a/arch/arm/boot/dts/am335x-phycore-rdk.dts b/arch/arm/boot/dts/am335x-phycore-rdk.dts
> new file mode 100644
> index 0000000..305f0b3
> --- /dev/null
> +++ b/arch/arm/boot/dts/am335x-phycore-rdk.dts
> @@ -0,0 +1,27 @@
> +/*
> + * Copyright (C) 2014 PHYTEC Messtechnik GmbH
> + * Author: Wadim Egorov <w.egorov@phytec.de>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +/dts-v1/;
> +
> +#include "am335x-phycore-som.dtsi"
> +#include "am335x-pcm-953.dtsi"
> +
> +/* SoM */
> +&i2c_eeprom {
> +	status = "okay";
> +};
> +
> +&i2c_rtc {
> +	status = "okay";
> +};
> +
> +&serial_flash {
> +	status = "okay";
> +
> +};
>
Teresa Remmet Jan. 20, 2017, 7:36 a.m. UTC | #2
Hello Vladimir,

thank you for your review.

Am Donnerstag, den 19.01.2017, 16:24 +0200 schrieb Vladimir Zapolskiy:
> On 01/19/2017 03:07 PM, Teresa Remmet wrote:
> > 
> > The phyCORE-AM335x development kit is a combination of the
> > phyCORE-AM335x SoM and a PCM-953 carrier board. The features
> > of the PCM-953 are:
> > * ETH phy on carrier board: 1x RGMII
> > * 1x CAN
> > * Up to 4x UART
> > * USB0 (otg)
> > * USB1 (host)
> > * SD slot
> > * User gpio-keys
> > * User LEDs
> > 
> > Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> > Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
> > ---
> >  .../devicetree/bindings/arm/omap/omap.txt          |   3 +
> >  arch/arm/boot/dts/Makefile                         |   1 +
> >  arch/arm/boot/dts/am335x-pcm-953.dtsi              | 303
> > +++++++++++++++++++++
> >  arch/arm/boot/dts/am335x-phycore-rdk.dts           |  27 ++
> >  4 files changed, 334 insertions(+)
> >  create mode 100644 arch/arm/boot/dts/am335x-pcm-953.dtsi
> >  create mode 100644 arch/arm/boot/dts/am335x-phycore-rdk.dts
> > 
> > diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt
> > b/Documentation/devicetree/bindings/arm/omap/omap.txt
> > index 05f95c3..8219b2c 100644
> > --- a/Documentation/devicetree/bindings/arm/omap/omap.txt
> > +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
> > @@ -151,6 +151,9 @@ Boards:
> >  - AM335X SBC-T335 : single board computer, built around the Sitara
> > AM3352/4
> >    compatible = "compulab,sbc-t335", "compulab,cm-t335",
> > "ti,am33xx"
> >  
> > +- AM335X phyCORE-AM335x: Development kit
> > +  compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-
> > som", "ti,am33xx"
> > +
> >  - OMAP5 EVM : Evaluation Module
> >    compatible = "ti,omap5-evm", "ti,omap5"
> >  
> > diff --git a/arch/arm/boot/dts/Makefile
> > b/arch/arm/boot/dts/Makefile
> > index 7327250..dd71afe 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -573,6 +573,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
> >  	am335x-lxm.dtb \
> >  	am335x-nano.dtb \
> >  	am335x-pepper.dtb \
> > +	am335x-phycore-rdk.dtb \
> >  	am335x-shc.dtb \
> >  	am335x-sbc-t335.dtb \
> >  	am335x-sl50.dtb \
> > diff --git a/arch/arm/boot/dts/am335x-pcm-953.dtsi
> > b/arch/arm/boot/dts/am335x-pcm-953.dtsi
> > new file mode 100644
> > index 0000000..54a171d
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/am335x-pcm-953.dtsi
> > @@ -0,0 +1,303 @@
> > +/*
> > + * Copyright (C) 2014-2017 Phytec Messtechnik GmbH
> > + * Author: Wadim Egorov <w.egorov@phytec.de>
> > + *	   Teresa Remmet <t.remmet@phytec.de>
> > + *
> > + * This program is free software; you can redistribute it and/or
> > modify
> > + * it under the terms of the GNU General Public License version 2
> > as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#include <dt-bindings/input/input.h>
> > +
> > +/ {
> > +	model = "Phytec AM335x PCM-953";
> > +	compatible = "phytec,am335x-pcm-953", "phytec,am335x-
> > phycore-som", "ti,am33xx";
> > +
> > +	user_leds: user_leds {
> > +		compatible = "gpio-leds";
> > +	};
> > +
> > +	user_buttons: user_buttons {
> > +		compatible = "gpio-keys";
> > +	};
> > +
> > +	regulators {
> > +		compatible = "simple-bus";
> Please drop "simple-bus" compatible, see http://www.spinics.net/lists
> /linux-usb/msg101497.html
> 

Ok, I will.

> > 
> > +
> > +		vcc3v3: fixedregulator@1 {
> > +			compatible = "regulator-fixed";
> > +		};
> > +
> > +		vcc1v8: fixedregulator@2 {
> > +			compatible = "regulator-fixed";
> > +		};
> > +	};
> > +};
> > +
> > +/* CAN */
> > +&am33xx_pinmux {
> Which .dtsi file contains the referenced am33xx_pinmux device node?
> 
> You should include that file firstly, this is relevant to all other
> references to device nodes used in this file.

The device tree for the Phytec AM335x boards is spitted apart, as they
consist of an SoM and a carrier board. The am33xx_pinmux is defined in
the am33xx.dtsi which is included in the am335x-phycore-som.dtsi.

> 
> > 
> > +	dcan1_pins: pinmux_dcan1 {
> > +		pinctrl-single,pins = <
> > +			AM33XX_IOPAD(0x980, PIN_OUTPUT_PULLUP |
> > MUX_MODE2)	/* uart1_rxd.dcan1_tx_mux2 */
> > +			AM33XX_IOPAD(0x984, PIN_INPUT_PULLUP |
> > MUX_MODE2)	/* uart1_txd.dcan1_rx_mux2 */
> > +		>;
> > +	};
> > +};
> > +
> > +&dcan1 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&dcan1_pins>;
> > +	status = "okay";
> > +};
> > +
> > +/* Ethernet */
> > +&am33xx_pinmux {
> > +	ethernet1_pins: pinmux_ethernet1 {
> > +		pinctrl-single,pins = <
> > +			AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a0.rgmii2_tctl */
> > +			AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a1.rgmii2_rctl */
> > +			AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a2.rgmii2_td3 */
> > +			AM33XX_IOPAD(0x84c, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a3.rgmii2_td2 */
> > +			AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a4.rgmii2_td1 */
> > +			AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a5.rgmii2_td0 */
> > +			AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a6.rgmii2_tclk */
> > +			AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a7.rgmii2_rclk */
> > +			AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a8.rgmii2_rd3 */
> > +			AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a9.rgmii2_rd2 */
> > +			AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a10.rgmii2_rd1 */
> > +			AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN |
> > MUX_MODE2)	/* gpmc_a11.rgmii2_rd0 */
> > +		>;
> > +	};
> > +};
> > +
> > +&cpsw_emac1 {
> > +	phy-handle = <&phy1>;
> > +	phy-mode = "rgmii-id";
> > +	dual_emac_res_vlan = <2>;
> > +	status = "okay";
> > +};
> > +
> > +&davinci_mdio {
> > +	phy1: ethernet-phy@1 {
> > +		reg = <2>;
> There is a mismatch between unit address and 'reg' property values.

I will fix that.

> 
> > 
> > +
> > +		/* Register 260 (104h) – RGMII Clock and Control
> > Pad Skew */
> > +		rxc-skew-ps = <1400>;
> > +		rxdv-skew-ps = <0>;
> > +		txc-skew-ps = <1400>;
> > +		txen-skew-ps = <0>;
> > +		/* Register 261 (105h) – RGMII RX Data Pad Skew */
> > +		rxd3-skew-ps = <0>;
> > +		rxd2-skew-ps = <0>;
> > +		rxd1-skew-ps = <0>;
> > +		rxd0-skew-ps = <0>;
> > +		/* Register 262 (106h) – RGMII TX Data Pad Skew */
> > +		txd3-skew-ps = <0>;
> > +		txd2-skew-ps = <0>;
> > +		txd1-skew-ps = <0>;
> > +		txd0-skew-ps = <0>;
> > +	};
> > +};
> > +
> > +&mac {
> > +	slaves = <2>;
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
> > +	dual_emac;
> It seems that TI has properties with underscores in the names, acked.
> 
> > 
> > +};
> > +
> > +/* Misc */
> > +&am33xx_pinmux {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&cb_gpio_pins>;
> > +
> > +	cb_gpio_pins: pinmux_cb_gpio {
> > +		pinctrl-single,pins = <
> > +			AM33XX_IOPAD(0x968, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE7)	/* uart0_ctsn.gpio1_8 */
> > +			AM33XX_IOPAD(0x96c, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE7)	/* uart0_rtsn.gpio1_9 */
> > +		>;
> > +	};
> > +};
> > +
> > +/* MMC */
> > +&am33xx_pinmux {
> > +	mmc1_pins: pinmux_mmc1_pins {
> > +		pinctrl-single,pins = <
> > +			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP |
> > MUX_MODE0)	/* mmc0_dat3.mmc0_dat3 */
> > +			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP |
> > MUX_MODE0)	/* mmc0_dat2.mmc0_dat2 */
> > +			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP |
> > MUX_MODE0)	/* mmc0_dat1.mmc0_dat1 */
> > +			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP |
> > MUX_MODE0)	/* mmc0_dat0.mmc0_dat0 */
> > +			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP |
> > MUX_MODE0)	/* mmc0_clk.mmc0_clk */
> > +			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP |
> > MUX_MODE0)	/* mmc0_cmd.mmc0_cmd */
> > +			AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP |
> > MUX_MODE7)	/* spi0_cs1.mmc0_sdcd */
> > +		>;
> > +	};
> > +};
> > +
> > +&mmc1 {
> > +	vmmc-supply = <&vcc3v3>;
> > +	bus-width = <4>;
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&mmc1_pins>;
> > +	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
> > +	status = "okay";
> > +};
> > +
> > +/* Power */
> > +&vcc3v3 {
> > +	regulator-name = "vcc3v3";
> > +	regulator-min-microvolt = <3300000>;
> > +	regulator-max-microvolt = <3300000>;
> > +	regulator-boot-on;
> > +};
> Please add properties directly into vcc3v3 device node.

I spitted the node apart as we structured the device tree in different
section. If I move this to the node directly the device tree
is not so readable in general any more. My opinion.
The same fits to the user leds and user buttons.

> 
> > 
> > +
> > +&vcc1v8 {
> > +	regulator-name = "vcc1v8";
> > +	regulator-min-microvolt = <1800000>;
> > +	regulator-max-microvolt = <1800000>;
> > +	regulator-boot-on;
> > +};
> > +
> Please add properties directly into vcc1v8 device node.
> 
> > 
> > +/* UARTs */
> > +&am33xx_pinmux {
> > +	uart0_pins: pinmux_uart0 {
> > +		pinctrl-single,pins = <
> > +			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP |
> > MUX_MODE0)	/* uart0_rxd.uart0_rxd */
> > +			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE0)	/* uart0_txd.uart0_txd */
> > +		>;
> > +	};
> > +
> > +	uart1_pins: pinmux_uart1 {
> > +		pinctrl-single,pins = <
> > +			AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP |
> > MUX_MODE0)	/* uart1_rxd.uart1_rxd */
> > +			AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE0)	/* uart1_txd.uart1_txd */
> > +			AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0)
> > 		/* uart1_ctsn.uart1_ctsn */
> > +			AM33XX_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE0)	/* uart1_rtsn.uart1_rtsn */
> > +		>;
> > +	};
> > +
> > +	uart2_pins: pinmux_uart2 {
> > +		pinctrl-single,pins = <
> > +			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP |
> > MUX_MODE1)	/* mii1_tx_clk.uart2_rxd */
> > +			AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE1)	/* mii1_rx_clk.uart2_txd */
> > +		>;
> > +	};
> > +
> > +	uart3_pins: pinmux_uart3 {
> > +		pinctrl-single,pins = <
> > +			AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP |
> > MUX_MODE1)	/* mii1_rxd3.uart3_rxd */
> > +			AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE1)	/* mii1_rxd2.uart3_txd */
> > +		>;
> > +	};
> > +};
> > +
> > +&uart0 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart0_pins>;
> > +	status = "okay";
> > +};
> > +
> > +&uart1 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart1_pins>;
> > +};
> > +
> > +&uart2 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart2_pins>;
> > +	status = "okay";
> > +};
> > +
> > +&uart3 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart3_pins>;
> > +	status = "okay";
> > +};
> > +
> > +/* USB */
> > +&cppi41dma {
> > +	status = "okay";
> > +};
> > +
> > +&usb_ctrl_mod {
> > +	status = "okay";
> > +};
> > +
> > +&usb {
> > +	status = "okay";
> > +};
> > +
> > +&usb0 {
> > +	status = "okay";
> > +};
> > +
> > +&usb0_phy {
> > +	status = "okay";
> > +};
> > +
> > +&usb1 {
> > +	status = "okay";
> > +	dr_mode = "host";
> > +};
> > +
> > +&usb1_phy {
> > +	status = "okay";
> > +};
> > +
> > +/* User IO */
> > +&am33xx_pinmux {
> > +	user_buttons_pins: pinmux_user_buttons {
> > +		pinctrl-single,pins = <
> > +			AM33XX_IOPAD(0x9e4, PIN_INPUT_PULLDOWN |
> > MUX_MODE7)	/* emu0.gpio3_7 */
> > +			AM33XX_IOPAD(0x9e8, PIN_INPUT_PULLDOWN |
> > MUX_MODE7)	/* emu1.gpio3_8 */
> > +		>;
> > +	};
> > +
> > +	user_leds_pins: pinmux_user_leds {
> > +		pinctrl-single,pins = <
> > +			AM33XX_IOPAD(0x880, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE7)	/* gpmc_csn1.gpio1_30 */
> > +			AM33XX_IOPAD(0x884, PIN_OUTPUT_PULLDOWN |
> > MUX_MODE7)	/* gpmc_csn2.gpio1_31 */
> > +		>;
> > +	};
> > +};
> > +
> > +&user_buttons {
> Please add properties directly into user_buttons device node.
> 
> > 
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&user_buttons_pins>;
> > +	status = "okay";
> Please remove the redundant property above.

I will remove it.

> 
> > 
> > +
> > +	button@0 {
> > +		label = "home";
> > +		linux,code = ;
> > +		gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
> > +		gpio-key,wakeup;
> > +	};
> > +
> > +	button@1 {
> > +		label = "menu";
> > +		linux,code = ;
> > +		gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
> > +		gpio-key,wakeup;
> > +	};
> > +};
> > +
> > +&user_leds {
> Please add properties directly into user_leds device node.
> 
> > 
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&user_leds_pins>;
> > +	status = "okay";
> Please remove the redundant property above.

I will remove it.

Thank you,
Teresa

> 
> > 
> > +
> > +	green {
> > +		label = "green:user";
> > +		gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> > +		linux,default-trigger = "gpio";
> > +		default-state = "on";
> > +	};
> > +
> > +	yellow {
> > +		label = "yellow:user";
> > +		gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
> > +		linux,default-trigger = "gpio";
> > +		default-state = "on";
> > +	};
> > +};
> > diff --git a/arch/arm/boot/dts/am335x-phycore-rdk.dts
> > b/arch/arm/boot/dts/am335x-phycore-rdk.dts
> > new file mode 100644
> > index 0000000..305f0b3
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/am335x-phycore-rdk.dts
> > @@ -0,0 +1,27 @@
> > +/*
> > + * Copyright (C) 2014 PHYTEC Messtechnik GmbH
> > + * Author: Wadim Egorov <w.egorov@phytec.de>
> > + *
> > + * This program is free software; you can redistribute it and/or
> > modify
> > + * it under the terms of the GNU General Public License version 2
> > as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "am335x-phycore-som.dtsi"
> > +#include "am335x-pcm-953.dtsi"
> > +
> > +/* SoM */
> > +&i2c_eeprom {
> > +	status = "okay";
> > +};
> > +
> > +&i2c_rtc {
> > +	status = "okay";
> > +};
> > +
> > +&serial_flash {
> > +	status = "okay";
> > +
> > +};
> >
Rob Herring Jan. 21, 2017, 8:53 p.m. UTC | #3
On Thu, Jan 19, 2017 at 02:07:48PM +0100, Teresa Remmet wrote:
> The phyCORE-AM335x development kit is a combination of the
> phyCORE-AM335x SoM and a PCM-953 carrier board. The features
> of the PCM-953 are:
> * ETH phy on carrier board: 1x RGMII
> * 1x CAN
> * Up to 4x UART
> * USB0 (otg)
> * USB1 (host)
> * SD slot
> * User gpio-keys
> * User LEDs
> 
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
> ---
>  .../devicetree/bindings/arm/omap/omap.txt          |   3 +
>  arch/arm/boot/dts/Makefile                         |   1 +
>  arch/arm/boot/dts/am335x-pcm-953.dtsi              | 303 +++++++++++++++++++++
>  arch/arm/boot/dts/am335x-phycore-rdk.dts           |  27 ++
>  4 files changed, 334 insertions(+)
>  create mode 100644 arch/arm/boot/dts/am335x-pcm-953.dtsi
>  create mode 100644 arch/arm/boot/dts/am335x-phycore-rdk.dts

[...]

> +	user_leds: user_leds {
> +		compatible = "gpio-leds";
> +	};
> +
> +	user_buttons: user_buttons {
> +		compatible = "gpio-keys";
> +	};

With only a compatible, I don't think there's much gain to split these 2 
nodes. Otherwse,

Acked-by: Rob Herring <robh@kernel.org>

> +&user_buttons {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&user_buttons_pins>;
> +	status = "okay";
> +
> +	button@0 {
> +		label = "home";
> +		linux,code = <KEY_HOME>;
> +		gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
> +		gpio-key,wakeup;
> +	};
> +
> +	button@1 {
> +		label = "menu";
> +		linux,code = <KEY_MENU>;
> +		gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
> +		gpio-key,wakeup;
> +	};
> +};
> +
> +&user_leds {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&user_leds_pins>;
> +	status = "okay";
> +
> +	green {
> +		label = "green:user";
> +		gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> +		linux,default-trigger = "gpio";
> +		default-state = "on";
> +	};
> +
> +	yellow {
> +		label = "yellow:user";
> +		gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
> +		linux,default-trigger = "gpio";
> +		default-state = "on";
> +	};
> +};
Teresa Remmet Jan. 23, 2017, 10:27 a.m. UTC | #4
Hello Rob,

Am Samstag, den 21.01.2017, 14:53 -0600 schrieb Rob Herring:
> On Thu, Jan 19, 2017 at 02:07:48PM +0100, Teresa Remmet wrote:
> > 
> > The phyCORE-AM335x development kit is a combination of the
> > phyCORE-AM335x SoM and a PCM-953 carrier board. The features
> > of the PCM-953 are:
> > * ETH phy on carrier board: 1x RGMII
> > * 1x CAN
> > * Up to 4x UART
> > * USB0 (otg)
> > * USB1 (host)
> > * SD slot
> > * User gpio-keys
> > * User LEDs
> > 
> > Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> > Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
> > ---
> >  .../devicetree/bindings/arm/omap/omap.txt          |   3 +
> >  arch/arm/boot/dts/Makefile                         |   1 +
> >  arch/arm/boot/dts/am335x-pcm-953.dtsi              | 303
> > +++++++++++++++++++++
> >  arch/arm/boot/dts/am335x-phycore-rdk.dts           |  27 ++
> >  4 files changed, 334 insertions(+)
> >  create mode 100644 arch/arm/boot/dts/am335x-pcm-953.dtsi
> >  create mode 100644 arch/arm/boot/dts/am335x-phycore-rdk.dts
> [...]
> 
> > 
> > +	user_leds: user_leds {
> > +		compatible = "gpio-leds";
> > +	};
> > +
> > +	user_buttons: user_buttons {
> > +		compatible = "gpio-keys";
> > +	};
> With only a compatible, I don't think there's much gain to split
> these 2 
> nodes. Otherwse,

whould it be ok to open up the root node again below? Or should I
better move the nodes up? Which does mess up the order then. We
orinented here on the am335x-pepper.dts. They also only keep the
compatibles in the root node.

Thanks,
Teresa

> 
> Acked-by: Rob Herring <robh@kernel.org>
> 
> > 
> > +&user_buttons {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&user_buttons_pins>;
> > +	status = "okay";
> > +
> > +	button@0 {
> > +		label = "home";
> > +		linux,code = <KEY_HOME>;
> > +		gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
> > +		gpio-key,wakeup;
> > +	};
> > +
> > +	button@1 {
> > +		label = "menu";
> > +		linux,code = <KEY_MENU>;
> > +		gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
> > +		gpio-key,wakeup;
> > +	};
> > +};
> > +
> > +&user_leds {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&user_leds_pins>;
> > +	status = "okay";
> > +
> > +	green {
> > +		label = "green:user";
> > +		gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> > +		linux,default-trigger = "gpio";
> > +		default-state = "on";
> > +	};
> > +
> > +	yellow {
> > +		label = "yellow:user";
> > +		gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
> > +		linux,default-trigger = "gpio";
> > +		default-state = "on";
> > +	};
> > +};
Rob Herring Jan. 23, 2017, 2:01 p.m. UTC | #5
On Mon, Jan 23, 2017 at 4:27 AM, Teresa Remmet <t.remmet@phytec.de> wrote:
> Hello Rob,
>
> Am Samstag, den 21.01.2017, 14:53 -0600 schrieb Rob Herring:
>> On Thu, Jan 19, 2017 at 02:07:48PM +0100, Teresa Remmet wrote:
>> >
>> > The phyCORE-AM335x development kit is a combination of the
>> > phyCORE-AM335x SoM and a PCM-953 carrier board. The features
>> > of the PCM-953 are:
>> > * ETH phy on carrier board: 1x RGMII
>> > * 1x CAN
>> > * Up to 4x UART
>> > * USB0 (otg)
>> > * USB1 (host)
>> > * SD slot
>> > * User gpio-keys
>> > * User LEDs
>> >
>> > Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
>> > Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
>> > ---
>> >  .../devicetree/bindings/arm/omap/omap.txt          |   3 +
>> >  arch/arm/boot/dts/Makefile                         |   1 +
>> >  arch/arm/boot/dts/am335x-pcm-953.dtsi              | 303
>> > +++++++++++++++++++++
>> >  arch/arm/boot/dts/am335x-phycore-rdk.dts           |  27 ++
>> >  4 files changed, 334 insertions(+)
>> >  create mode 100644 arch/arm/boot/dts/am335x-pcm-953.dtsi
>> >  create mode 100644 arch/arm/boot/dts/am335x-phycore-rdk.dts
>> [...]
>>
>> >
>> > +   user_leds: user_leds {
>> > +           compatible = "gpio-leds";
>> > +   };
>> > +
>> > +   user_buttons: user_buttons {
>> > +           compatible = "gpio-keys";
>> > +   };
>> With only a compatible, I don't think there's much gain to split
>> these 2
>> nodes. Otherwse,
>
> whould it be ok to open up the root node again below? Or should I
> better move the nodes up? Which does mess up the order then. We
> orinented here on the am335x-pepper.dts. They also only keep the
> compatibles in the root node.

The order is not important. It is silly to have the same node twice in
the same file. Someone should fix am335x-pepper.dts, too.

The split is generally what is chip specific and board specific, but
this is all board specific.

Rob
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 05f95c3..8219b2c 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -151,6 +151,9 @@  Boards:
 - AM335X SBC-T335 : single board computer, built around the Sitara AM3352/4
   compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx"
 
+- AM335X phyCORE-AM335x: Development kit
+  compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx"
+
 - OMAP5 EVM : Evaluation Module
   compatible = "ti,omap5-evm", "ti,omap5"
 
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7327250..dd71afe 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -573,6 +573,7 @@  dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-lxm.dtb \
 	am335x-nano.dtb \
 	am335x-pepper.dtb \
+	am335x-phycore-rdk.dtb \
 	am335x-shc.dtb \
 	am335x-sbc-t335.dtb \
 	am335x-sl50.dtb \
diff --git a/arch/arm/boot/dts/am335x-pcm-953.dtsi b/arch/arm/boot/dts/am335x-pcm-953.dtsi
new file mode 100644
index 0000000..54a171d
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-pcm-953.dtsi
@@ -0,0 +1,303 @@ 
+/*
+ * Copyright (C) 2014-2017 Phytec Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ *	   Teresa Remmet <t.remmet@phytec.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Phytec AM335x PCM-953";
+	compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx";
+
+	user_leds: user_leds {
+		compatible = "gpio-leds";
+	};
+
+	user_buttons: user_buttons {
+		compatible = "gpio-keys";
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		vcc3v3: fixedregulator@1 {
+			compatible = "regulator-fixed";
+		};
+
+		vcc1v8: fixedregulator@2 {
+			compatible = "regulator-fixed";
+		};
+	};
+};
+
+/* CAN */
+&am33xx_pinmux {
+	dcan1_pins: pinmux_dcan1 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x980, PIN_OUTPUT_PULLUP | MUX_MODE2)	/* uart1_rxd.dcan1_tx_mux2 */
+			AM33XX_IOPAD(0x984, PIN_INPUT_PULLUP | MUX_MODE2)	/* uart1_txd.dcan1_rx_mux2 */
+		>;
+	};
+};
+
+&dcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dcan1_pins>;
+	status = "okay";
+};
+
+/* Ethernet */
+&am33xx_pinmux {
+	ethernet1_pins: pinmux_ethernet1 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a0.rgmii2_tctl */
+			AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a1.rgmii2_rctl */
+			AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a2.rgmii2_td3 */
+			AM33XX_IOPAD(0x84c, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a3.rgmii2_td2 */
+			AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a4.rgmii2_td1 */
+			AM33XX_IOPAD(0x854, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a5.rgmii2_td0 */
+			AM33XX_IOPAD(0x858, PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a6.rgmii2_tclk */
+			AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a7.rgmii2_rclk */
+			AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a8.rgmii2_rd3 */
+			AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a9.rgmii2_rd2 */
+			AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a10.rgmii2_rd1 */
+			AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a11.rgmii2_rd0 */
+		>;
+	};
+};
+
+&cpsw_emac1 {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	dual_emac_res_vlan = <2>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <2>;
+
+		/* Register 260 (104h) – RGMII Clock and Control Pad Skew */
+		rxc-skew-ps = <1400>;
+		rxdv-skew-ps = <0>;
+		txc-skew-ps = <1400>;
+		txen-skew-ps = <0>;
+		/* Register 261 (105h) – RGMII RX Data Pad Skew */
+		rxd3-skew-ps = <0>;
+		rxd2-skew-ps = <0>;
+		rxd1-skew-ps = <0>;
+		rxd0-skew-ps = <0>;
+		/* Register 262 (106h) – RGMII TX Data Pad Skew */
+		txd3-skew-ps = <0>;
+		txd2-skew-ps = <0>;
+		txd1-skew-ps = <0>;
+		txd0-skew-ps = <0>;
+	};
+};
+
+&mac {
+	slaves = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
+	dual_emac;
+};
+
+/* Misc */
+&am33xx_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cb_gpio_pins>;
+
+	cb_gpio_pins: pinmux_cb_gpio {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x968, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart0_ctsn.gpio1_8 */
+			AM33XX_IOPAD(0x96c, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* uart0_rtsn.gpio1_9 */
+		>;
+	};
+};
+
+/* MMC */
+&am33xx_pinmux {
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat3.mmc0_dat3 */
+			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat2.mmc0_dat2 */
+			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat1.mmc0_dat1 */
+			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat0.mmc0_dat0 */
+			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_clk.mmc0_clk */
+			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_cmd.mmc0_cmd */
+			AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE7)	/* spi0_cs1.mmc0_sdcd */
+		>;
+	};
+};
+
+&mmc1 {
+	vmmc-supply = <&vcc3v3>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+/* Power */
+&vcc3v3 {
+	regulator-name = "vcc3v3";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-boot-on;
+};
+
+&vcc1v8 {
+	regulator-name = "vcc1v8";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-boot-on;
+};
+
+/* UARTs */
+&am33xx_pinmux {
+	uart0_pins: pinmux_uart0 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+		>;
+	};
+
+	uart1_pins: pinmux_uart1 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart1_rxd.uart1_rxd */
+			AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_txd.uart1_txd */
+			AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0)		/* uart1_ctsn.uart1_ctsn */
+			AM33XX_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_rtsn.uart1_rtsn */
+		>;
+	};
+
+	uart2_pins: pinmux_uart2 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE1)	/* mii1_tx_clk.uart2_rxd */
+			AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_rx_clk.uart2_txd */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3 {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE1)	/* mii1_rxd3.uart3_rxd */
+			AM33XX_IOPAD(0x938, PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* mii1_rxd2.uart3_txd */
+		>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "okay";
+};
+
+/* USB */
+&cppi41dma {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+/* User IO */
+&am33xx_pinmux {
+	user_buttons_pins: pinmux_user_buttons {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9e4, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* emu0.gpio3_7 */
+			AM33XX_IOPAD(0x9e8, PIN_INPUT_PULLDOWN | MUX_MODE7)	/* emu1.gpio3_8 */
+		>;
+	};
+
+	user_leds_pins: pinmux_user_leds {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x880, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn1.gpio1_30 */
+			AM33XX_IOPAD(0x884, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn2.gpio1_31 */
+		>;
+	};
+};
+
+&user_buttons {
+	pinctrl-names = "default";
+	pinctrl-0 = <&user_buttons_pins>;
+	status = "okay";
+
+	button@0 {
+		label = "home";
+		linux,code = <KEY_HOME>;
+		gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+		gpio-key,wakeup;
+	};
+
+	button@1 {
+		label = "menu";
+		linux,code = <KEY_MENU>;
+		gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
+		gpio-key,wakeup;
+	};
+};
+
+&user_leds {
+	pinctrl-names = "default";
+	pinctrl-0 = <&user_leds_pins>;
+	status = "okay";
+
+	green {
+		label = "green:user";
+		gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+		linux,default-trigger = "gpio";
+		default-state = "on";
+	};
+
+	yellow {
+		label = "yellow:user";
+		gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
+		linux,default-trigger = "gpio";
+		default-state = "on";
+	};
+};
diff --git a/arch/arm/boot/dts/am335x-phycore-rdk.dts b/arch/arm/boot/dts/am335x-phycore-rdk.dts
new file mode 100644
index 0000000..305f0b3
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-phycore-rdk.dts
@@ -0,0 +1,27 @@ 
+/*
+ * Copyright (C) 2014 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "am335x-phycore-som.dtsi"
+#include "am335x-pcm-953.dtsi"
+
+/* SoM */
+&i2c_eeprom {
+	status = "okay";
+};
+
+&i2c_rtc {
+	status = "okay";
+};
+
+&serial_flash {
+	status = "okay";
+
+};