diff mbox

[v2] clk: qcom: gdsc: Fix handling of hw control enable/disable

Message ID 1485145581-517-1-git-send-email-rnayak@codeaurora.org (mailing list archive)
State Accepted
Delegated to: Stephen Boyd
Headers show

Commit Message

Rajendra Nayak Jan. 23, 2017, 4:26 a.m. UTC 
Once a gdsc is brought in and out of HW control, there is a
power down and up cycle which can take upto 1us. Polling on
the gdsc status immediately after the hw control enable/disable
can mislead software/firmware to belive the gdsc is already either on
or off, while its yet to complete the power cycle.
To avoid this add a 1us delay post a enable/disable of HW control
mode.

Also after the HW control mode is disabled, poll on the status to
check gdsc status reflects its 'on' before force disabling it
in software.

Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
---
 drivers/clk/qcom/gdsc.c | 58 ++++++++++++++++++++++++++++++++++++++-----------
 1 file changed, 45 insertions(+), 13 deletions(-)

Comments

Stanimir Varbanov Jan. 26, 2017, 9:31 p.m. UTC | #1 
Hi,

Thanks for the patch!

On 23.01.2017 06:26, Rajendra Nayak wrote:
> Once a gdsc is brought in and out of HW control, there is a
> power down and up cycle which can take upto 1us. Polling on
> the gdsc status immediately after the hw control enable/disable
> can mislead software/firmware to belive the gdsc is already either on
> or off, while its yet to complete the power cycle.
> To avoid this add a 1us delay post a enable/disable of HW control
> mode.
>
> Also after the HW control mode is disabled, poll on the status to
> check gdsc status reflects its 'on' before force disabling it
> in software.
>
> Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
> Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
> ---
>  drivers/clk/qcom/gdsc.c | 58 ++++++++++++++++++++++++++++++++++++++-----------
>  1 file changed, 45 insertions(+), 13 deletions(-)

Reviewed and Tested-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>

regards,
Stan
--
To unsubscribe from this list: send the line "unsubscribe linux-clk" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Stephen Boyd Jan. 27, 2017, midnight UTC | #2 
On 01/23, Rajendra Nayak wrote:
> Once a gdsc is brought in and out of HW control, there is a
> power down and up cycle which can take upto 1us. Polling on
> the gdsc status immediately after the hw control enable/disable
> can mislead software/firmware to belive the gdsc is already either on
> or off, while its yet to complete the power cycle.
> To avoid this add a 1us delay post a enable/disable of HW control
> mode.
> 
> Also after the HW control mode is disabled, poll on the status to
> check gdsc status reflects its 'on' before force disabling it
> in software.
> 
> Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
> Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
> ---

Applied to clk-next + I added a fixes tag. I don't think any
driver is affected by this problem in mainline, hence the punt to
v4.11.
diff mbox

Patch

diff --git a/drivers/clk/qcom/gdsc.c b/drivers/clk/qcom/gdsc.c
index 288186c..a4f3580 100644
--- a/drivers/clk/qcom/gdsc.c
+++ b/drivers/clk/qcom/gdsc.c
@@ -63,11 +63,26 @@  static int gdsc_hwctrl(struct gdsc *sc, bool en)
 	return regmap_update_bits(sc->regmap, sc->gdscr, HW_CONTROL_MASK, val);
 }
 
+static int gdsc_poll_status(struct gdsc *sc, unsigned int reg, bool en)
+{
+	ktime_t start;
+
+	start = ktime_get();
+	do {
+		if (gdsc_is_enabled(sc, reg) == en)
+			return 0;
+	} while (ktime_us_delta(ktime_get(), start) < TIMEOUT_US);
+
+	if (gdsc_is_enabled(sc, reg) == en)
+		return 0;
+
+	return -ETIMEDOUT;
+}
+
 static int gdsc_toggle_logic(struct gdsc *sc, bool en)
 {
 	int ret;
 	u32 val = en ? 0 : SW_COLLAPSE_MASK;
-	ktime_t start;
 	unsigned int status_reg = sc->gdscr;
 
 	ret = regmap_update_bits(sc->regmap, sc->gdscr, SW_COLLAPSE_MASK, val);
@@ -100,16 +115,7 @@  static int gdsc_toggle_logic(struct gdsc *sc, bool en)
 		udelay(1);
 	}
 
-	start = ktime_get();
-	do {
-		if (gdsc_is_enabled(sc, status_reg) == en)
-			return 0;
-	} while (ktime_us_delta(ktime_get(), start) < TIMEOUT_US);
-
-	if (gdsc_is_enabled(sc, status_reg) == en)
-		return 0;
-
-	return -ETIMEDOUT;
+	return gdsc_poll_status(sc, status_reg, en);
 }
 
 static inline int gdsc_deassert_reset(struct gdsc *sc)
@@ -188,8 +194,20 @@  static int gdsc_enable(struct generic_pm_domain *domain)
 	udelay(1);
 
 	/* Turn on HW trigger mode if supported */
-	if (sc->flags & HW_CTRL)
-		return gdsc_hwctrl(sc, true);
+	if (sc->flags & HW_CTRL) {
+		ret = gdsc_hwctrl(sc, true);
+		if (ret)
+			return ret;
+		/*
+		 * Wait for the GDSC to go through a power down and
+		 * up cycle.  In case a firmware ends up polling status
+		 * bits for the gdsc, it might read an 'on' status before
+		 * the GDSC can finish the power cycle.
+		 * We wait 1us before returning to ensure the firmware
+		 * can't immediately poll the status bits.
+		 */
+		udelay(1);
+	}
 
 	return 0;
 }
@@ -204,9 +222,23 @@  static int gdsc_disable(struct generic_pm_domain *domain)
 
 	/* Turn off HW trigger mode if supported */
 	if (sc->flags & HW_CTRL) {
+		unsigned int reg;
+
 		ret = gdsc_hwctrl(sc, false);
 		if (ret < 0)
 			return ret;
+		/*
+		 * Wait for the GDSC to go through a power down and
+		 * up cycle.  In case we end up polling status
+		 * bits for the gdsc before the power cycle is completed
+		 * it might read an 'on' status wrongly.
+		 */
+		udelay(1);
+
+		reg = sc->gds_hw_ctrl ? sc->gds_hw_ctrl : sc->gdscr;
+		ret = gdsc_poll_status(sc, reg, true);
+		if (ret)
+			return ret;
 	}
 
 	if (sc->pwrsts & PWRSTS_OFF)