Message ID | 1485515090-7570-2-git-send-email-horms+renesas@verge.net.au (mailing list archive) |
---|---|
State | Superseded |
Delegated to: | Geert Uytterhoeven |
Headers | show |
Hello! On 01/27/2017 02:04 PM, Simon Horman wrote: > From: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > > This patch enables tx and rx clock internal delay modes (TDM and RDM). > > This is to address a failure in the case of 1Gbps communication using the > by salvator-x board with the KSZ9031RNX phy. This has been reported to > occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs. > > With this change APSR internal delay modes are enabled for > "rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows: > > phy mode | ASPR delay mode > -----------+---------------- > rgmii-id | TDM and RDM > rgmii-rxid | RDM > rgmii-txid | TDM > > Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > > --- > v1 [Simon Horman] > - Combined patches > - Reworded changelog > > v0 [Kazuya Mizuguchi] > --- > drivers/net/ethernet/renesas/ravb.h | 10 ++++++++++ > drivers/net/ethernet/renesas/ravb_main.c | 29 +++++++++++++++++++++++++++++ > 2 files changed, 39 insertions(+) > > diff --git a/drivers/net/ethernet/renesas/ravb.h b/drivers/net/ethernet/renesas/ravb.h > index f1109661a533..d7c91d48cc48 100644 > --- a/drivers/net/ethernet/renesas/ravb.h > +++ b/drivers/net/ethernet/renesas/ravb.h [...] > @@ -248,6 +249,15 @@ enum ESR_BIT { > ESR_EIL = 0x00001000, > }; > > +/* APSR */ > +enum APSR_BIT { > + APSR_MEMS = 0x00000002, Not documented in the revision 0.5 of the gen3 manual... > + APSR_CMSW = 0x00000010, > + APSR_DM = 0x00006000, ... and neither this field. Are these documented in the latter revs? > + APSR_DM_RDM = 0x00002000, > + APSR_DM_TDM = 0x00004000, > +}; > + > /* RCR */ > enum RCR_BIT { > RCR_EFFS = 0x00000001, > diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c > index 89ac1e3f6175..9fb4c04c5885 100644 > --- a/drivers/net/ethernet/renesas/ravb_main.c > +++ b/drivers/net/ethernet/renesas/ravb_main.c > @@ -1904,6 +1904,29 @@ static void ravb_set_config_mode(struct net_device *ndev) > } > } > > +static void ravb_set_delay_mode(struct net_device *ndev) > +{ > + struct ravb_private *priv = netdev_priv(ndev); > + > + if (priv->chip_id != RCAR_GEN2) { > + switch (priv->phy_interface) { > + case PHY_INTERFACE_MODE_RGMII_ID: > + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM | > + APSR_DM_TDM); > + break; > + case PHY_INTERFACE_MODE_RGMII_RXID: > + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM); > + break; > + case PHY_INTERFACE_MODE_RGMII_TXID: > + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_TDM); > + break; > + default: > + ravb_modify(ndev, APSR, APSR_DM, 0); > + break; > + } How about doing ravb_modify() only once? [...] MNR, Sergei
On 01/27/2017 02:04 PM, Simon Horman wrote: > From: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > > This patch enables tx and rx clock internal delay modes (TDM and RDM). > > This is to address a failure in the case of 1Gbps communication using the > by salvator-x board with the KSZ9031RNX phy. This has been reported to > occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs. > > With this change APSR internal delay modes are enabled for > "rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows: > > phy mode | ASPR delay mode > -----------+---------------- > rgmii-id | TDM and RDM > rgmii-rxid | RDM > rgmii-txid | TDM > > Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > > --- > v1 [Simon Horman] > - Combined patches > - Reworded changelog > > v0 [Kazuya Mizuguchi] [...] > diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c > index 89ac1e3f6175..9fb4c04c5885 100644 > --- a/drivers/net/ethernet/renesas/ravb_main.c > +++ b/drivers/net/ethernet/renesas/ravb_main.c > @@ -1904,6 +1904,29 @@ static void ravb_set_config_mode(struct net_device *ndev) > } > } > > +static void ravb_set_delay_mode(struct net_device *ndev) > +{ > + struct ravb_private *priv = netdev_priv(ndev); > + > + if (priv->chip_id != RCAR_GEN2) { > + switch (priv->phy_interface) { > + case PHY_INTERFACE_MODE_RGMII_ID: > + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM | > + APSR_DM_TDM); > + break; > + case PHY_INTERFACE_MODE_RGMII_RXID: > + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM); > + break; > + case PHY_INTERFACE_MODE_RGMII_TXID: > + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_TDM); > + break; > + default: > + ravb_modify(ndev, APSR, APSR_DM, 0); > + break; > + } > + } > +} > + > static int ravb_probe(struct platform_device *pdev) > { > struct device_node *np = pdev->dev.of_node; > @@ -2016,6 +2039,9 @@ static int ravb_probe(struct platform_device *pdev) > /* Request GTI loading */ > ravb_modify(ndev, GCCR, GCCR_LTI, GCCR_LTI); > > + /* Set APSR */ > + ravb_set_delay_mode(ndev); > + > /* Allocate descriptor base address table */ > priv->desc_bat_size = sizeof(struct ravb_desc) * DBAT_ENTRY_NUM; > priv->desc_bat = dma_alloc_coherent(ndev->dev.parent, priv->desc_bat_size, > @@ -2152,6 +2178,9 @@ static int __maybe_unused ravb_resume(struct device *dev) > /* Request GTI loading */ > ravb_modify(ndev, GCCR, GCCR_LTI, GCCR_LTI); > > + /* Set APSR */ > + ravb_set_delay_mode(ndev); > + So far the pattern was to first check if gen != 2, then calling a gen3 specific function. I'd like to keep it, rather than checking in the function itself. [...] MBR, Sergei
On Fri, Jan 27, 2017 at 03:42:05PM +0300, Sergei Shtylyov wrote: > Hello! > > On 01/27/2017 02:04 PM, Simon Horman wrote: > > >From: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > > > >This patch enables tx and rx clock internal delay modes (TDM and RDM). > > > >This is to address a failure in the case of 1Gbps communication using the > >by salvator-x board with the KSZ9031RNX phy. This has been reported to > >occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs. > > > >With this change APSR internal delay modes are enabled for > >"rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows: > > > >phy mode | ASPR delay mode > >-----------+---------------- > >rgmii-id | TDM and RDM > >rgmii-rxid | RDM > >rgmii-txid | TDM > > > >Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > >Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > > > >--- > >v1 [Simon Horman] > >- Combined patches > >- Reworded changelog > > > >v0 [Kazuya Mizuguchi] > >--- > > drivers/net/ethernet/renesas/ravb.h | 10 ++++++++++ > > drivers/net/ethernet/renesas/ravb_main.c | 29 +++++++++++++++++++++++++++++ > > 2 files changed, 39 insertions(+) > > > >diff --git a/drivers/net/ethernet/renesas/ravb.h b/drivers/net/ethernet/renesas/ravb.h > >index f1109661a533..d7c91d48cc48 100644 > >--- a/drivers/net/ethernet/renesas/ravb.h > >+++ b/drivers/net/ethernet/renesas/ravb.h > [...] > >@@ -248,6 +249,15 @@ enum ESR_BIT { > > ESR_EIL = 0x00001000, > > }; > > > >+/* APSR */ > >+enum APSR_BIT { > >+ APSR_MEMS = 0x00000002, > > Not documented in the revision 0.5 of the gen3 manual... It is in version 0.53 of the documentation but I think it can be dropped from this patch as its unused. > >+ APSR_CMSW = 0x00000010, I think the above can also be dropped as it is unused. > >+ APSR_DM = 0x00006000, > > ... and neither this field. Are these documented in the latter revs? This one is not. I can ask Mizuguchi-san to confirm it exists (with himself). > >+ APSR_DM_RDM = 0x00002000, > >+ APSR_DM_TDM = 0x00004000, > >+}; > >+ > > /* RCR */ > > enum RCR_BIT { > > RCR_EFFS = 0x00000001, > >diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c > >index 89ac1e3f6175..9fb4c04c5885 100644 > >--- a/drivers/net/ethernet/renesas/ravb_main.c > >+++ b/drivers/net/ethernet/renesas/ravb_main.c > >@@ -1904,6 +1904,29 @@ static void ravb_set_config_mode(struct net_device *ndev) > > } > > } > > > >+static void ravb_set_delay_mode(struct net_device *ndev) > >+{ > >+ struct ravb_private *priv = netdev_priv(ndev); > >+ > >+ if (priv->chip_id != RCAR_GEN2) { > >+ switch (priv->phy_interface) { > >+ case PHY_INTERFACE_MODE_RGMII_ID: > >+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM | > >+ APSR_DM_TDM); > >+ break; > >+ case PHY_INTERFACE_MODE_RGMII_RXID: > >+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM); > >+ break; > >+ case PHY_INTERFACE_MODE_RGMII_TXID: > >+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_TDM); > >+ break; > >+ default: > >+ ravb_modify(ndev, APSR, APSR_DM, 0); > >+ break; > >+ } > > How about doing ravb_modify() only once? Something like this? int set = 0; if (priv->phy_interface == PHY_INTERFACE_MODE_RGMII_ID || priv->phy_interface == PHY_INTERFACE_MODE_RGMII_RXID) set |= APSR_DM_RDM; if (priv->phy_interface == PHY_INTERFACE_MODE_RGMII_ID || priv->phy_interface == PHY_INTERFACE_MODE_RGMII_TXID) set |= APSR_DM_TDM; ravb_modify(ndev, APSR, APSR_DM, set); I don't really see any advantage to it but I can change things around however you like.
On Fri, Jan 27, 2017 at 04:00:27PM +0300, Sergei Shtylyov wrote: > On 01/27/2017 02:04 PM, Simon Horman wrote: > > >From: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > > > >This patch enables tx and rx clock internal delay modes (TDM and RDM). > > > >This is to address a failure in the case of 1Gbps communication using the > >by salvator-x board with the KSZ9031RNX phy. This has been reported to > >occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs. > > > >With this change APSR internal delay modes are enabled for > >"rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows: > > > >phy mode | ASPR delay mode > >-----------+---------------- > >rgmii-id | TDM and RDM > >rgmii-rxid | RDM > >rgmii-txid | TDM > > > >Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > >Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > > > >--- > >v1 [Simon Horman] > >- Combined patches > >- Reworded changelog > > > >v0 [Kazuya Mizuguchi] > [...] > >diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c > >index 89ac1e3f6175..9fb4c04c5885 100644 > >--- a/drivers/net/ethernet/renesas/ravb_main.c > >+++ b/drivers/net/ethernet/renesas/ravb_main.c > >@@ -1904,6 +1904,29 @@ static void ravb_set_config_mode(struct net_device *ndev) > > } > > } > > > >+static void ravb_set_delay_mode(struct net_device *ndev) > >+{ > >+ struct ravb_private *priv = netdev_priv(ndev); > >+ > >+ if (priv->chip_id != RCAR_GEN2) { > >+ switch (priv->phy_interface) { > >+ case PHY_INTERFACE_MODE_RGMII_ID: > >+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM | > >+ APSR_DM_TDM); > >+ break; > >+ case PHY_INTERFACE_MODE_RGMII_RXID: > >+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM); > >+ break; > >+ case PHY_INTERFACE_MODE_RGMII_TXID: > >+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_TDM); > >+ break; > >+ default: > >+ ravb_modify(ndev, APSR, APSR_DM, 0); > >+ break; > >+ } > >+ } > >+} > >+ > > static int ravb_probe(struct platform_device *pdev) > > { > > struct device_node *np = pdev->dev.of_node; > >@@ -2016,6 +2039,9 @@ static int ravb_probe(struct platform_device *pdev) > > /* Request GTI loading */ > > ravb_modify(ndev, GCCR, GCCR_LTI, GCCR_LTI); > > > >+ /* Set APSR */ > >+ ravb_set_delay_mode(ndev); > >+ > > /* Allocate descriptor base address table */ > > priv->desc_bat_size = sizeof(struct ravb_desc) * DBAT_ENTRY_NUM; > > priv->desc_bat = dma_alloc_coherent(ndev->dev.parent, priv->desc_bat_size, > >@@ -2152,6 +2178,9 @@ static int __maybe_unused ravb_resume(struct device *dev) > > /* Request GTI loading */ > > ravb_modify(ndev, GCCR, GCCR_LTI, GCCR_LTI); > > > >+ /* Set APSR */ > >+ ravb_set_delay_mode(ndev); > >+ > > So far the pattern was to first check if gen != 2, then calling a gen3 > specific function. I'd like to keep it, rather than checking in the function > itself. So you would like something like? /* Set APSR */ if (priv->chip_id != RCAR_GEN2) ravb_set_delay_mode(ndev); That does not seem better to me but I can make it so if that is your preference.
On 01/27/2017 07:49 PM, Simon Horman wrote: >>> From: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> >>> >>> This patch enables tx and rx clock internal delay modes (TDM and RDM). >>> >>> This is to address a failure in the case of 1Gbps communication using the >>> by salvator-x board with the KSZ9031RNX phy. This has been reported to >>> occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs. >>> >>> With this change APSR internal delay modes are enabled for >>> "rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows: >>> >>> phy mode | ASPR delay mode >>> -----------+---------------- >>> rgmii-id | TDM and RDM >>> rgmii-rxid | RDM >>> rgmii-txid | TDM >>> >>> Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> >>> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> >>> >>> --- >>> v1 [Simon Horman] >>> - Combined patches >>> - Reworded changelog >>> >>> v0 [Kazuya Mizuguchi] >>> --- >>> drivers/net/ethernet/renesas/ravb.h | 10 ++++++++++ >>> drivers/net/ethernet/renesas/ravb_main.c | 29 +++++++++++++++++++++++++++++ >>> 2 files changed, 39 insertions(+) >>> >>> diff --git a/drivers/net/ethernet/renesas/ravb.h b/drivers/net/ethernet/renesas/ravb.h >>> index f1109661a533..d7c91d48cc48 100644 >>> --- a/drivers/net/ethernet/renesas/ravb.h >>> +++ b/drivers/net/ethernet/renesas/ravb.h >> [...] >>> @@ -248,6 +249,15 @@ enum ESR_BIT { >>> ESR_EIL = 0x00001000, >>> }; >>> >>> +/* APSR */ >>> +enum APSR_BIT { >>> + APSR_MEMS = 0x00000002, >> >> Not documented in the revision 0.5 of the gen3 manual... > > It is in version 0.53 of the documentation but I think it can be dropped > from this patch as its unused. No need to drop, let it be. :-) >>> + APSR_CMSW = 0x00000010, > > I think the above can also be dropped as it is unused. No need. >>> + APSR_DM = 0x00006000, >> >> ... and neither this field. Are these documented in the latter revs? > > This one is not. I can ask Mizuguchi-san to confirm it exists (with himself). The whole patch depends on it! If it's not documented, I'd like a comment added, like I did for the other undocumented things in this driver... [...] >>> diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c >>> index 89ac1e3f6175..9fb4c04c5885 100644 >>> --- a/drivers/net/ethernet/renesas/ravb_main.c >>> +++ b/drivers/net/ethernet/renesas/ravb_main.c >>> @@ -1904,6 +1904,29 @@ static void ravb_set_config_mode(struct net_device *ndev) >>> } >>> } >>> >>> +static void ravb_set_delay_mode(struct net_device *ndev) >>> +{ >>> + struct ravb_private *priv = netdev_priv(ndev); >>> + >>> + if (priv->chip_id != RCAR_GEN2) { >>> + switch (priv->phy_interface) { >>> + case PHY_INTERFACE_MODE_RGMII_ID: >>> + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM | >>> + APSR_DM_TDM); >>> + break; >>> + case PHY_INTERFACE_MODE_RGMII_RXID: >>> + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM); >>> + break; >>> + case PHY_INTERFACE_MODE_RGMII_TXID: >>> + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_TDM); >>> + break; >>> + default: >>> + ravb_modify(ndev, APSR, APSR_DM, 0); >>> + break; >>> + } >> >> How about doing ravb_modify() only once? > > Something like this? > > int set = 0; > > if (priv->phy_interface == PHY_INTERFACE_MODE_RGMII_ID || > priv->phy_interface == PHY_INTERFACE_MODE_RGMII_RXID) > set |= APSR_DM_RDM; > > if (priv->phy_interface == PHY_INTERFACE_MODE_RGMII_ID || > priv->phy_interface == PHY_INTERFACE_MODE_RGMII_TXID) > set |= APSR_DM_TDM; > > ravb_modify(ndev, APSR, APSR_DM, set); > > I don't really see any advantage to it but I can change things around > however you like. I didn't mean to replace *switch*, actually -- just to move ravb_modify() out of it. MBR, Sergei
On 01/27/2017 07:51 PM, Simon Horman wrote: >>> From: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> >>> >>> This patch enables tx and rx clock internal delay modes (TDM and RDM). >>> >>> This is to address a failure in the case of 1Gbps communication using the >>> by salvator-x board with the KSZ9031RNX phy. This has been reported to >>> occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs. >>> >>> With this change APSR internal delay modes are enabled for >>> "rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows: >>> >>> phy mode | ASPR delay mode >>> -----------+---------------- >>> rgmii-id | TDM and RDM >>> rgmii-rxid | RDM >>> rgmii-txid | TDM >>> >>> Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> >>> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> >>> >>> --- >>> v1 [Simon Horman] >>> - Combined patches >>> - Reworded changelog >>> >>> v0 [Kazuya Mizuguchi] >> [...] >>> diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c >>> index 89ac1e3f6175..9fb4c04c5885 100644 >>> --- a/drivers/net/ethernet/renesas/ravb_main.c >>> +++ b/drivers/net/ethernet/renesas/ravb_main.c [...] >>> @@ -2016,6 +2039,9 @@ static int ravb_probe(struct platform_device *pdev) >>> /* Request GTI loading */ >>> ravb_modify(ndev, GCCR, GCCR_LTI, GCCR_LTI); >>> >>> + /* Set APSR */ >>> + ravb_set_delay_mode(ndev); >>> + >>> /* Allocate descriptor base address table */ >>> priv->desc_bat_size = sizeof(struct ravb_desc) * DBAT_ENTRY_NUM; >>> priv->desc_bat = dma_alloc_coherent(ndev->dev.parent, priv->desc_bat_size, >>> @@ -2152,6 +2178,9 @@ static int __maybe_unused ravb_resume(struct device *dev) >>> /* Request GTI loading */ >>> ravb_modify(ndev, GCCR, GCCR_LTI, GCCR_LTI); >>> >>> + /* Set APSR */ >>> + ravb_set_delay_mode(ndev); >>> + >> >> So far the pattern was to first check if gen != 2, then calling a gen3 >> specific function. I'd like to keep it, rather than checking in the function >> itself. > > So you would like something like? > > /* Set APSR */ > if (priv->chip_id != RCAR_GEN2) > ravb_set_delay_mode(ndev); Yes (except the comment). > > That does not seem better to me but I can make it so if that is your > preference. Yes, not better code-wise but more consistent. MBR, Sergei
On Fri, Jan 27, 2017 at 07:55:25PM +0300, Sergei Shtylyov wrote: > On 01/27/2017 07:49 PM, Simon Horman wrote: > > >>>From: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > >>> > >>>This patch enables tx and rx clock internal delay modes (TDM and RDM). > >>> > >>>This is to address a failure in the case of 1Gbps communication using the > >>>by salvator-x board with the KSZ9031RNX phy. This has been reported to > >>>occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs. > >>> > >>>With this change APSR internal delay modes are enabled for > >>>"rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows: > >>> > >>>phy mode | ASPR delay mode > >>>-----------+---------------- > >>>rgmii-id | TDM and RDM > >>>rgmii-rxid | RDM > >>>rgmii-txid | TDM > >>> > >>>Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > >>>Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > >>> > >>>--- > >>>v1 [Simon Horman] > >>>- Combined patches > >>>- Reworded changelog > >>> > >>>v0 [Kazuya Mizuguchi] > >>>--- > >>>drivers/net/ethernet/renesas/ravb.h | 10 ++++++++++ > >>>drivers/net/ethernet/renesas/ravb_main.c | 29 +++++++++++++++++++++++++++++ > >>>2 files changed, 39 insertions(+) > >>> > >>>diff --git a/drivers/net/ethernet/renesas/ravb.h b/drivers/net/ethernet/renesas/ravb.h > >>>index f1109661a533..d7c91d48cc48 100644 > >>>--- a/drivers/net/ethernet/renesas/ravb.h > >>>+++ b/drivers/net/ethernet/renesas/ravb.h > >>[...] > >>>@@ -248,6 +249,15 @@ enum ESR_BIT { > >>> ESR_EIL = 0x00001000, > >>>}; > >>> > >>>+/* APSR */ > >>>+enum APSR_BIT { > >>>+ APSR_MEMS = 0x00000002, > >> > >> Not documented in the revision 0.5 of the gen3 manual... > > > >It is in version 0.53 of the documentation but I think it can be dropped > >from this patch as its unused. > > No need to drop, let it be. :-) > > >>>+ APSR_CMSW = 0x00000010, > > > >I think the above can also be dropped as it is unused. > > No need. Ok, lets leave it and MEMS. > >>>+ APSR_DM = 0x00006000, > >> > >> ... and neither this field. Are these documented in the latter revs? > > > >This one is not. I can ask Mizuguchi-san to confirm it exists (with himself). > > The whole patch depends on it! If it's not documented, I'd like a comment > added, like I did for the other undocumented things in this driver... Sure. > [...] > >>>diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c > >>>index 89ac1e3f6175..9fb4c04c5885 100644 > >>>--- a/drivers/net/ethernet/renesas/ravb_main.c > >>>+++ b/drivers/net/ethernet/renesas/ravb_main.c > >>>@@ -1904,6 +1904,29 @@ static void ravb_set_config_mode(struct net_device *ndev) > >>> } > >>>} > >>> > >>>+static void ravb_set_delay_mode(struct net_device *ndev) > >>>+{ > >>>+ struct ravb_private *priv = netdev_priv(ndev); > >>>+ > >>>+ if (priv->chip_id != RCAR_GEN2) { > >>>+ switch (priv->phy_interface) { > >>>+ case PHY_INTERFACE_MODE_RGMII_ID: > >>>+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM | > >>>+ APSR_DM_TDM); > >>>+ break; > >>>+ case PHY_INTERFACE_MODE_RGMII_RXID: > >>>+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM); > >>>+ break; > >>>+ case PHY_INTERFACE_MODE_RGMII_TXID: > >>>+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_TDM); > >>>+ break; > >>>+ default: > >>>+ ravb_modify(ndev, APSR, APSR_DM, 0); > >>>+ break; > >>>+ } > >> > >> How about doing ravb_modify() only once? > > > >Something like this? > > > > int set = 0; > > > > if (priv->phy_interface == PHY_INTERFACE_MODE_RGMII_ID || > > priv->phy_interface == PHY_INTERFACE_MODE_RGMII_RXID) > > set |= APSR_DM_RDM; > > > > if (priv->phy_interface == PHY_INTERFACE_MODE_RGMII_ID || > > priv->phy_interface == PHY_INTERFACE_MODE_RGMII_TXID) > > set |= APSR_DM_TDM; > > > > ravb_modify(ndev, APSR, APSR_DM, set); > > > >I don't really see any advantage to it but I can change things around > >however you like. > > I didn't mean to replace *switch*, actually -- just to move ravb_modify() > out of it. Ok, I will make it so.
On 01/27/2017 09:07 PM, Simon Horman wrote: >>>>> From: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> >>>>> >>>>> This patch enables tx and rx clock internal delay modes (TDM and RDM). >>>>> >>>>> This is to address a failure in the case of 1Gbps communication using the >>>>> by salvator-x board with the KSZ9031RNX phy. This has been reported to >>>>> occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs. >>>>> >>>>> With this change APSR internal delay modes are enabled for >>>>> "rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows: >>>>> >>>>> phy mode | ASPR delay mode >>>>> -----------+---------------- >>>>> rgmii-id | TDM and RDM >>>>> rgmii-rxid | RDM >>>>> rgmii-txid | TDM >>>>> >>>>> Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> >>>>> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> >>>>> >>>>> --- >>>>> v1 [Simon Horman] >>>>> - Combined patches >>>>> - Reworded changelog >>>>> >>>>> v0 [Kazuya Mizuguchi] >>>>> --- >>>>> drivers/net/ethernet/renesas/ravb.h | 10 ++++++++++ >>>>> drivers/net/ethernet/renesas/ravb_main.c | 29 +++++++++++++++++++++++++++++ >>>>> 2 files changed, 39 insertions(+) >>>>> >>>>> diff --git a/drivers/net/ethernet/renesas/ravb.h b/drivers/net/ethernet/renesas/ravb.h >>>>> index f1109661a533..d7c91d48cc48 100644 >>>>> --- a/drivers/net/ethernet/renesas/ravb.h >>>>> +++ b/drivers/net/ethernet/renesas/ravb.h >>>> [...] >>>>> @@ -248,6 +249,15 @@ enum ESR_BIT { >>>>> ESR_EIL = 0x00001000, >>>>> }; >>>>> >>>>> +/* APSR */ >>>>> +enum APSR_BIT { >>>>> + APSR_MEMS = 0x00000002, >>>> >>>> Not documented in the revision 0.5 of the gen3 manual... >>> >>> It is in version 0.53 of the documentation but I think it can be dropped >> >from this patch as its unused. >> >> No need to drop, let it be. :-) >> >>>>> + APSR_CMSW = 0x00000010, >>> >>> I think the above can also be dropped as it is unused. >> >> No need. > > Ok, lets leave it and MEMS. > >>>>> + APSR_DM = 0x00006000, >>>> >>>> ... and neither this field. Are these documented in the latter revs? >>> >>> This one is not. I can ask Mizuguchi-san to confirm it exists (with himself). >> >> The whole patch depends on it! If it's not documented, I'd like a comment >> added, like I did for the other undocumented things in this driver... > > Sure. > >> [...] >>>>> diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c >>>>> index 89ac1e3f6175..9fb4c04c5885 100644 >>>>> --- a/drivers/net/ethernet/renesas/ravb_main.c >>>>> +++ b/drivers/net/ethernet/renesas/ravb_main.c >>>>> @@ -1904,6 +1904,29 @@ static void ravb_set_config_mode(struct net_device *ndev) >>>>> } >>>>> } >>>>> >>>>> +static void ravb_set_delay_mode(struct net_device *ndev) >>>>> +{ >>>>> + struct ravb_private *priv = netdev_priv(ndev); >>>>> + >>>>> + if (priv->chip_id != RCAR_GEN2) { >>>>> + switch (priv->phy_interface) { >>>>> + case PHY_INTERFACE_MODE_RGMII_ID: >>>>> + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM | >>>>> + APSR_DM_TDM); >>>>> + break; >>>>> + case PHY_INTERFACE_MODE_RGMII_RXID: >>>>> + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM); >>>>> + break; >>>>> + case PHY_INTERFACE_MODE_RGMII_TXID: >>>>> + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_TDM); >>>>> + break; >>>>> + default: >>>>> + ravb_modify(ndev, APSR, APSR_DM, 0); >>>>> + break; >>>>> + } >>>> >>>> How about doing ravb_modify() only once? >>> >>> Something like this? >>> >>> int set = 0; >>> >>> if (priv->phy_interface == PHY_INTERFACE_MODE_RGMII_ID || >>> priv->phy_interface == PHY_INTERFACE_MODE_RGMII_RXID) >>> set |= APSR_DM_RDM; >>> >>> if (priv->phy_interface == PHY_INTERFACE_MODE_RGMII_ID || >>> priv->phy_interface == PHY_INTERFACE_MODE_RGMII_TXID) >>> set |= APSR_DM_TDM; >>> >>> ravb_modify(ndev, APSR, APSR_DM, set); >>> >>> I don't really see any advantage to it but I can change things around >>> however you like. >> >> I didn't mean to replace *switch*, actually -- just to move ravb_modify() >> out of it. > > Ok, I will make it so. Your variant is probably even better! :-) I'm not sure how good gcc is at merging the similar code paths, simplifying its work seems worth it to me. The less repetitive code, the better. MBR, Sergei
On Fri, Jan 27, 2017 at 09:11:35PM +0300, Sergei Shtylyov wrote: > On 01/27/2017 09:07 PM, Simon Horman wrote: > > >>>>>From: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > >>>>> > >>>>>This patch enables tx and rx clock internal delay modes (TDM and RDM). > >>>>> > >>>>>This is to address a failure in the case of 1Gbps communication using the > >>>>>by salvator-x board with the KSZ9031RNX phy. This has been reported to > >>>>>occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs. > >>>>> > >>>>>With this change APSR internal delay modes are enabled for > >>>>>"rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows: > >>>>> > >>>>>phy mode | ASPR delay mode > >>>>>-----------+---------------- > >>>>>rgmii-id | TDM and RDM > >>>>>rgmii-rxid | RDM > >>>>>rgmii-txid | TDM > >>>>> > >>>>>Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> > >>>>>Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > >>>>> > >>>>>--- > >>>>>v1 [Simon Horman] > >>>>>- Combined patches > >>>>>- Reworded changelog > >>>>> > >>>>>v0 [Kazuya Mizuguchi] > >>>>>--- > >>>>>drivers/net/ethernet/renesas/ravb.h | 10 ++++++++++ > >>>>>drivers/net/ethernet/renesas/ravb_main.c | 29 +++++++++++++++++++++++++++++ > >>>>>2 files changed, 39 insertions(+) > >>>>> > >>>>>diff --git a/drivers/net/ethernet/renesas/ravb.h b/drivers/net/ethernet/renesas/ravb.h > >>>>>index f1109661a533..d7c91d48cc48 100644 > >>>>>--- a/drivers/net/ethernet/renesas/ravb.h > >>>>>+++ b/drivers/net/ethernet/renesas/ravb.h > >>>>[...] > >>>>>@@ -248,6 +249,15 @@ enum ESR_BIT { > >>>>> ESR_EIL = 0x00001000, > >>>>>}; > >>>>> > >>>>>+/* APSR */ > >>>>>+enum APSR_BIT { > >>>>>+ APSR_MEMS = 0x00000002, > >>>> > >>>> Not documented in the revision 0.5 of the gen3 manual... > >>> > >>>It is in version 0.53 of the documentation but I think it can be dropped > >>>from this patch as its unused. > >> > >> No need to drop, let it be. :-) > >> > >>>>>+ APSR_CMSW = 0x00000010, > >>> > >>>I think the above can also be dropped as it is unused. > >> > >> No need. > > > >Ok, lets leave it and MEMS. > > > >>>>>+ APSR_DM = 0x00006000, > >>>> > >>>> ... and neither this field. Are these documented in the latter revs? > >>> > >>>This one is not. I can ask Mizuguchi-san to confirm it exists (with himself). > >> > >> The whole patch depends on it! If it's not documented, I'd like a comment > >>added, like I did for the other undocumented things in this driver... > > > >Sure. > > > >>[...] > >>>>>diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c > >>>>>index 89ac1e3f6175..9fb4c04c5885 100644 > >>>>>--- a/drivers/net/ethernet/renesas/ravb_main.c > >>>>>+++ b/drivers/net/ethernet/renesas/ravb_main.c > >>>>>@@ -1904,6 +1904,29 @@ static void ravb_set_config_mode(struct net_device *ndev) > >>>>> } > >>>>>} > >>>>> > >>>>>+static void ravb_set_delay_mode(struct net_device *ndev) > >>>>>+{ > >>>>>+ struct ravb_private *priv = netdev_priv(ndev); > >>>>>+ > >>>>>+ if (priv->chip_id != RCAR_GEN2) { > >>>>>+ switch (priv->phy_interface) { > >>>>>+ case PHY_INTERFACE_MODE_RGMII_ID: > >>>>>+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM | > >>>>>+ APSR_DM_TDM); > >>>>>+ break; > >>>>>+ case PHY_INTERFACE_MODE_RGMII_RXID: > >>>>>+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM); > >>>>>+ break; > >>>>>+ case PHY_INTERFACE_MODE_RGMII_TXID: > >>>>>+ ravb_modify(ndev, APSR, APSR_DM, APSR_DM_TDM); > >>>>>+ break; > >>>>>+ default: > >>>>>+ ravb_modify(ndev, APSR, APSR_DM, 0); > >>>>>+ break; > >>>>>+ } > >>>> > >>>> How about doing ravb_modify() only once? > >>> > >>>Something like this? > >>> > >>> int set = 0; > >>> > >>> if (priv->phy_interface == PHY_INTERFACE_MODE_RGMII_ID || > >>> priv->phy_interface == PHY_INTERFACE_MODE_RGMII_RXID) > >>> set |= APSR_DM_RDM; > >>> > >>> if (priv->phy_interface == PHY_INTERFACE_MODE_RGMII_ID || > >>> priv->phy_interface == PHY_INTERFACE_MODE_RGMII_TXID) > >>> set |= APSR_DM_TDM; > >>> > >>> ravb_modify(ndev, APSR, APSR_DM, set); > >>> > >>>I don't really see any advantage to it but I can change things around > >>>however you like. > >> > >> I didn't mean to replace *switch*, actually -- just to move ravb_modify() > >>out of it. > > > >Ok, I will make it so. > > Your variant is probably even better! :-) > I'm not sure how good gcc is at merging the similar code paths, > simplifying its work seems worth it to me. The less repetitive code, the > better. Ok, thanks. I'll go with my version.
diff --git a/drivers/net/ethernet/renesas/ravb.h b/drivers/net/ethernet/renesas/ravb.h index f1109661a533..d7c91d48cc48 100644 --- a/drivers/net/ethernet/renesas/ravb.h +++ b/drivers/net/ethernet/renesas/ravb.h @@ -76,6 +76,7 @@ enum ravb_reg { CDAR20 = 0x0060, CDAR21 = 0x0064, ESR = 0x0088, + APSR = 0x008C, /* R-Car Gen3 only */ RCR = 0x0090, RQC0 = 0x0094, RQC1 = 0x0098, @@ -248,6 +249,15 @@ enum ESR_BIT { ESR_EIL = 0x00001000, }; +/* APSR */ +enum APSR_BIT { + APSR_MEMS = 0x00000002, + APSR_CMSW = 0x00000010, + APSR_DM = 0x00006000, + APSR_DM_RDM = 0x00002000, + APSR_DM_TDM = 0x00004000, +}; + /* RCR */ enum RCR_BIT { RCR_EFFS = 0x00000001, diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c index 89ac1e3f6175..9fb4c04c5885 100644 --- a/drivers/net/ethernet/renesas/ravb_main.c +++ b/drivers/net/ethernet/renesas/ravb_main.c @@ -1904,6 +1904,29 @@ static void ravb_set_config_mode(struct net_device *ndev) } } +static void ravb_set_delay_mode(struct net_device *ndev) +{ + struct ravb_private *priv = netdev_priv(ndev); + + if (priv->chip_id != RCAR_GEN2) { + switch (priv->phy_interface) { + case PHY_INTERFACE_MODE_RGMII_ID: + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM | + APSR_DM_TDM); + break; + case PHY_INTERFACE_MODE_RGMII_RXID: + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_RDM); + break; + case PHY_INTERFACE_MODE_RGMII_TXID: + ravb_modify(ndev, APSR, APSR_DM, APSR_DM_TDM); + break; + default: + ravb_modify(ndev, APSR, APSR_DM, 0); + break; + } + } +} + static int ravb_probe(struct platform_device *pdev) { struct device_node *np = pdev->dev.of_node; @@ -2016,6 +2039,9 @@ static int ravb_probe(struct platform_device *pdev) /* Request GTI loading */ ravb_modify(ndev, GCCR, GCCR_LTI, GCCR_LTI); + /* Set APSR */ + ravb_set_delay_mode(ndev); + /* Allocate descriptor base address table */ priv->desc_bat_size = sizeof(struct ravb_desc) * DBAT_ENTRY_NUM; priv->desc_bat = dma_alloc_coherent(ndev->dev.parent, priv->desc_bat_size, @@ -2152,6 +2178,9 @@ static int __maybe_unused ravb_resume(struct device *dev) /* Request GTI loading */ ravb_modify(ndev, GCCR, GCCR_LTI, GCCR_LTI); + /* Set APSR */ + ravb_set_delay_mode(ndev); + /* Restore descriptor base address table */ ravb_write(ndev, priv->desc_bat_dma, DBAT);