Message ID | 20170223104025.5755-1-zajec5@gmail.com (mailing list archive) |
---|---|
State | Changes Requested, archived |
Headers | show |
Hi Rafal, As discussed for other platforms as well, please use the board's name as the same board can end up being sold under multiple model numbers. So please rename the file to bcm47094-linksys-panamera.dts Best, Imre On 2017-02-23 11:40, Rafał Miłecki wrote: > From: Rafał Miłecki <rafal@milecki.pl> > > It's tri-band wireless home router based on BCM47094 AKA BCM4709C0. It > uses 3 x BCM4366 chipsets for wireless. > > Signed-off-by: Rafał Miłecki <rafal@milecki.pl> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/bcm47094-linksys-ea9500.dts | 36 +++++++++++++++++++++++++++ > 2 files changed, 37 insertions(+) > create mode 100644 arch/arm/boot/dts/bcm47094-linksys-ea9500.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 52a05289c538..931db0b41246 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ > bcm4709-netgear-r8000.dtb \ > bcm4709-tplink-archer-c9-v1.dtb \ > bcm47094-dlink-dir-885l.dtb \ > + bcm47094-linksys-ea9500.dtb \ > bcm47094-luxul-xwr-3100.dtb \ > bcm47094-netgear-r8500.dtb \ > bcm94708.dtb \ > diff --git a/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts b/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts > new file mode 100644 > index 000000000000..31639e5b8c72 > --- /dev/null > +++ b/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts > @@ -0,0 +1,36 @@ > +/* > + * Copyright (C) 2017 Rafał Miłecki <rafal@milecki.pl> > + * > + * Licensed under the ISC license. > + */ > + > +/dts-v1/; > + > +#include "bcm47094.dtsi" > +#include "bcm5301x-nand-cs0-bch8.dtsi" > + > +/ { > + compatible = "linksys,ea9500", "brcm,bcm47094", "brcm,bcm4708"; > + model = "Linksys EA9500"; > + > + chosen { > + bootargs = "console=ttyS0,115200"; > + }; > + > + memory { > + reg = <0x00000000 0x08000000 > + 0x88000000 0x08000000>; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + wps { > + label = "WPS"; > + linux,code = <KEY_WPS_BUTTON>; > + gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; > + }; > + }; > +}; >
On 23 February 2017 at 13:27, Imre Kaloz <kaloz@openwrt.org> wrote: > As discussed for other platforms as well, please use the board's name as the > same board can end up being sold under multiple model numbers. > > So please rename the file to bcm47094-linksys-panamera.dts Huh? Where did you get panamera name from?!
Dear Rafal, On 2017-02-23 13:29, Rafał Miłecki wrote: > On 23 February 2017 at 13:27, Imre Kaloz <kaloz@openwrt.org> wrote: >> As discussed for other platforms as well, please use the board's name as the >> same board can end up being sold under multiple model numbers. >> >> So please rename the file to bcm47094-linksys-panamera.dts > Huh? Where did you get panamera name from?! Your manners shine on these dark days of winter. For about a decade now, http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if you are too lazy to look into the GPL tarball or at the original bootlogs. Best, Imre
On 23 February 2017 at 13:44, Imre Kaloz <kaloz@openwrt.org> wrote: > On 2017-02-23 13:29, Rafał Miłecki wrote: >> >> On 23 February 2017 at 13:27, Imre Kaloz <kaloz@openwrt.org> wrote: >>> >>> As discussed for other platforms as well, please use the board's name as >>> the >>> same board can end up being sold under multiple model numbers. >>> >>> So please rename the file to bcm47094-linksys-panamera.dts >> >> Huh? Where did you get panamera name from?! > > Your manners shine on these dark days of winter. For about a decade now, > http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if > you are too lazy to look into the GPL tarball or at the original bootlogs. Sadly Linksys doesn't sponsor me or provide me any hardware. The bootlogs I found: https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/ http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30 didn't include board name. As you probably can guess http://192.168.1.1/ was useful in my case as well.
On 23 February 2017 at 13:51, Rafał Miłecki <zajec5@gmail.com> wrote: > On 23 February 2017 at 13:44, Imre Kaloz <kaloz@openwrt.org> wrote: >> On 2017-02-23 13:29, Rafał Miłecki wrote: >>> >>> On 23 February 2017 at 13:27, Imre Kaloz <kaloz@openwrt.org> wrote: >>>> >>>> As discussed for other platforms as well, please use the board's name as >>>> the >>>> same board can end up being sold under multiple model numbers. >>>> >>>> So please rename the file to bcm47094-linksys-panamera.dts >>> >>> Huh? Where did you get panamera name from?! >> >> Your manners shine on these dark days of winter. For about a decade now, >> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if >> you are too lazy to look into the GPL tarball or at the original bootlogs. > > Sadly Linksys doesn't sponsor me or provide me any hardware. The > bootlogs I found: > https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/ > http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30 > didn't include board name. As you probably can guess > http://192.168.1.1/ was useful in my case as well. Or rather "useless" ;)
Dear Rafal, On 2017-02-23 13:51, Rafał Miłecki wrote: > On 23 February 2017 at 13:44, Imre Kaloz <kaloz@openwrt.org> wrote: >> On 2017-02-23 13:29, Rafał Miłecki wrote: >>> On 23 February 2017 at 13:27, Imre Kaloz <kaloz@openwrt.org> wrote: >>>> As discussed for other platforms as well, please use the board's name as >>>> the >>>> same board can end up being sold under multiple model numbers. >>>> >>>> So please rename the file to bcm47094-linksys-panamera.dts >>> Huh? Where did you get panamera name from?! >> Your manners shine on these dark days of winter. For about a decade now, >> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if >> you are too lazy to look into the GPL tarball or at the original bootlogs. > Sadly Linksys doesn't sponsor me or provide me any hardware. The > bootlogs I found: > https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/ > http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30 > didn't include board name. As you probably can guess > http://192.168.1.1/ was useful in my case as well. > I've guessed you have the hardware - so you're submitting dts files without testing it? I know they don't do much, but still, this is an interesting concept. Anyways, if you are just adding support for hardware blindly, the dd-wrt forum you've mentioned has other posts that might help you [1]. Best, Imre [1] http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1062050
On 23 February 2017 at 13:59, Imre Kaloz <kaloz@openwrt.org> wrote: > On 2017-02-23 13:51, Rafał Miłecki wrote: >> >> On 23 February 2017 at 13:44, Imre Kaloz <kaloz@openwrt.org> wrote: >>> >>> On 2017-02-23 13:29, Rafał Miłecki wrote: >>>> >>>> On 23 February 2017 at 13:27, Imre Kaloz <kaloz@openwrt.org> wrote: >>>>> >>>>> As discussed for other platforms as well, please use the board's name >>>>> as >>>>> the >>>>> same board can end up being sold under multiple model numbers. >>>>> >>>>> So please rename the file to bcm47094-linksys-panamera.dts >>>> >>>> Huh? Where did you get panamera name from?! >>> >>> Your manners shine on these dark days of winter. For about a decade now, >>> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information >>> if >>> you are too lazy to look into the GPL tarball or at the original >>> bootlogs. >> >> Sadly Linksys doesn't sponsor me or provide me any hardware. The >> bootlogs I found: >> https://www.snbforums.com/threads/ea9500-serial-console-to-cfe.35228/ >> http://www.dd-wrt.com/phpBB2/viewtopic.php?t=288470&start=30 >> didn't include board name. As you probably can guess >> http://192.168.1.1/ was useful in my case as well. >> > > I've guessed you have the hardware - so you're submitting dts files without > testing it? I know they don't do much, but still, this is an interesting > concept. I'm sending what was tested by EA9500 user: https://forum.lede-project.org/t/lede-tested-on-linksys-ea9500/1612 I'm planning to add better support for this device, but it requires extra testing which may take some time. So I just started with what I can provide so far.
On 23 February 2017 at 13:44, Imre Kaloz <kaloz@openwrt.org> wrote: > On 2017-02-23 13:29, Rafał Miłecki wrote: >> >> On 23 February 2017 at 13:27, Imre Kaloz <kaloz@openwrt.org> wrote: >>> >>> As discussed for other platforms as well, please use the board's name as >>> the >>> same board can end up being sold under multiple model numbers. >>> >>> So please rename the file to bcm47094-linksys-panamera.dts >> >> Huh? Where did you get panamera name from?! > > Your manners shine on these dark days of winter. For about a decade now, > http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if > you are too lazy to look into the GPL tarball or at the original bootlogs. Today I decided to do my homework & check GPL sources of EA9500 fw. I grepped them for panamera and I found this name in few files: ./checkpatches ./src/mod_bdutil/platform/brcm/usbhub.h ./src/mod_bdutil/platform/brcm/buttons.h ./src/mod_bdutil/platform/brcm/usbhub.c ./src/mod_bdutil/platform/brcm/leds_panamera.c ./src/mod_bdutil/platform/brcm/leds.c ./src/mod_bdutil/bdutil.h.panamera ./src/mod_bdutil/Makefile.panamera Unfortunately all these results aren't very clear for getting board name of EA9500. I checked them and panamera is only one of listed boards there. E.g. checkpatches contains following lines: # patched by BRCM for Panamera # patched by BRCM for F70 # patched by BRCM for Pinnacles # patched by BRCM for EA9200 So EA9500 board name could be any of above. Similarly there are following Makefiles in EA9500 GPL package: Makefile.audi Makefile.bentley Makefile.blk-mamba Makefile.carrera Makefile.esprit Makefile.f70 Makefile.focus Makefile.honda Makefile.impala Makefile.lemans Makefile.mamba Makefile.panamera Makefile.pub Makefile.r8 Makefile.spyder Makefile.taurus Makefile.viper Makefile.viperuivm Makefile.wraith So again, any of these name could be EA9500 board name. Will you be so generous to tell us how did you get EA9500 board name by just looking at GPL sources?
On 24 February 2017 at 07:02, Rafał Miłecki <zajec5@gmail.com> wrote: > On 23 February 2017 at 13:44, Imre Kaloz <kaloz@openwrt.org> wrote: >> On 2017-02-23 13:29, Rafał Miłecki wrote: >>> >>> On 23 February 2017 at 13:27, Imre Kaloz <kaloz@openwrt.org> wrote: >>>> >>>> As discussed for other platforms as well, please use the board's name as >>>> the >>>> same board can end up being sold under multiple model numbers. >>>> >>>> So please rename the file to bcm47094-linksys-panamera.dts >>> >>> Huh? Where did you get panamera name from?! >> >> Your manners shine on these dark days of winter. For about a decade now, >> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if >> you are too lazy to look into the GPL tarball or at the original bootlogs. > > Today I decided to do my homework & check GPL sources of EA9500 fw. > > (...) > > Will you be so generous to tell us how did you get EA9500 board name > by just looking at GPL sources? I also tried find with -name "*panamera*". One way of guessing board name seems to be checking names of patches in ./src/linux/patches/. Any other, more reliable method?
Dear Rafal, On 2017-02-24 07:10, Rafał Miłecki wrote: >>> Your manners shine on these dark days of winter. For about a decade now, >>> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information if >>> you are too lazy to look into the GPL tarball or at the original bootlogs. >> Today I decided to do my homework & check GPL sources of EA9500 fw. >> >> (...) >> >> Will you be so generous to tell us how did you get EA9500 board name >> by just looking at GPL sources? > I also tried find with -name "*panamera*". One way of guessing board > name seems to be checking names of patches in ./src/linux/patches/. > Any other, more reliable method? > First of all, it's really weird you never ever looked at the factory bootlogs, but let me help in hope to enhance your communication style: filenames: src/linux/patches/linux-2.6.36.4-panamera_000_BSP.patch src/linux/patches/linux-2.6.36.4-panamera_001_brcm_build.patch src/linux/patches/linux-2.6.36.4-panamera_002_brcm_build_flags_temp_fix.patch src/linux/patches/linux-2.6.36.4-panamera_003_ctf_bypass.patch src/linux/patches/linux-2.6.36.4-panamera_006_cisco_comment.patch src/linux/patches/linux-2.6.36.4-panamera_007_usb_remove_oops.patch src/linux/patches/linux-2.6.36.4-panamera_008_6rd_sit_fragment.patch src/linux/patches/linux-2.6.36.4-panamera_009_cisco_rtsp_conntrack.patch src/linux/patches/linux-2.6.36.4-panamera_010_cisco_rtsp_conntrack2.patch src/linux/patches/linux-2.6.36.4-panamera_014_ftp_pasv_command.patch src/linux/patches/linux-2.6.36.4-panamera_046_sip_alg.patch src/linux/patches/linux-2.6.36.4-panamera_047_add_usb_led.patch src/linux/patches/linux-2.6.36.4-panamera_050_PPTP_L2TP_ctf.patch src/linux/patches/linux-2.6.36.4-panamera_052_cfe_pass_led_to_blink.patch src/linux/patches/linux-2.6.36.4-panamera_201_brcm_patch_20160226.patch file contents: src/mod_bdutil/platform/brcm/.board_id.o.cmd src/mod_bdutil/platform/brcm/.buttons.o.cmd src/mod_bdutil/platform/brcm/.leds_panamera.o.cmd src/mod_bdutil/platform/brcm/.usbhub.o.cmd If you have further questions, feel free to mail me directly and keep off-topic discussion away from the lists. Thank you and have a nice weekend, Imre
On 25 February 2017 at 23:43, Imre Kaloz <kaloz@openwrt.org> wrote: > On 2017-02-24 07:10, Rafał Miłecki wrote: >>>> >>>> Your manners shine on these dark days of winter. For about a decade now, >>>> http://192.168.1.1/sysinfo.cgi will show you quite a bit of information >>>> if >>>> you are too lazy to look into the GPL tarball or at the original >>>> bootlogs. >>> >>> Today I decided to do my homework & check GPL sources of EA9500 fw. >>> >>> (...) >>> >>> Will you be so generous to tell us how did you get EA9500 board name >>> by just looking at GPL sources? >> >> I also tried find with -name "*panamera*". One way of guessing board >> name seems to be checking names of patches in ./src/linux/patches/. >> Any other, more reliable method? >> > > First of all, it's really weird you never ever looked at the factory > bootlogs, but let me help in hope to enhance your communication style: > > filenames: > > src/linux/patches/linux-2.6.36.4-panamera_000_BSP.patch > src/linux/patches/linux-2.6.36.4-panamera_001_brcm_build.patch > src/linux/patches/linux-2.6.36.4-panamera_002_brcm_build_flags_temp_fix.patch > src/linux/patches/linux-2.6.36.4-panamera_003_ctf_bypass.patch > src/linux/patches/linux-2.6.36.4-panamera_006_cisco_comment.patch > src/linux/patches/linux-2.6.36.4-panamera_007_usb_remove_oops.patch > src/linux/patches/linux-2.6.36.4-panamera_008_6rd_sit_fragment.patch > src/linux/patches/linux-2.6.36.4-panamera_009_cisco_rtsp_conntrack.patch > src/linux/patches/linux-2.6.36.4-panamera_010_cisco_rtsp_conntrack2.patch > src/linux/patches/linux-2.6.36.4-panamera_014_ftp_pasv_command.patch > src/linux/patches/linux-2.6.36.4-panamera_046_sip_alg.patch > src/linux/patches/linux-2.6.36.4-panamera_047_add_usb_led.patch > src/linux/patches/linux-2.6.36.4-panamera_050_PPTP_L2TP_ctf.patch > src/linux/patches/linux-2.6.36.4-panamera_052_cfe_pass_led_to_blink.patch > src/linux/patches/linux-2.6.36.4-panamera_201_brcm_patch_20160226.patch > > file contents: > > src/mod_bdutil/platform/brcm/.board_id.o.cmd > src/mod_bdutil/platform/brcm/.buttons.o.cmd > src/mod_bdutil/platform/brcm/.leds_panamera.o.cmd > src/mod_bdutil/platform/brcm/.usbhub.o.cmd > > > If you have further questions, feel free to mail me directly and keep > off-topic discussion away from the lists. Thanks
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 52a05289c538..931db0b41246 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm4709-netgear-r8000.dtb \ bcm4709-tplink-archer-c9-v1.dtb \ bcm47094-dlink-dir-885l.dtb \ + bcm47094-linksys-ea9500.dtb \ bcm47094-luxul-xwr-3100.dtb \ bcm47094-netgear-r8500.dtb \ bcm94708.dtb \ diff --git a/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts b/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts new file mode 100644 index 000000000000..31639e5b8c72 --- /dev/null +++ b/arch/arm/boot/dts/bcm47094-linksys-ea9500.dts @@ -0,0 +1,36 @@ +/* + * Copyright (C) 2017 Rafał Miłecki <rafal@milecki.pl> + * + * Licensed under the ISC license. + */ + +/dts-v1/; + +#include "bcm47094.dtsi" +#include "bcm5301x-nand-cs0-bch8.dtsi" + +/ { + compatible = "linksys,ea9500", "brcm,bcm47094", "brcm,bcm4708"; + model = "Linksys EA9500"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + reg = <0x00000000 0x08000000 + 0x88000000 0x08000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + wps { + label = "WPS"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; + }; + }; +};