diff mbox

[v10,1/3] dt-bindings: Add support for samsung s6e3ha2 panel binding

Message ID 8e5109d0-6e6f-8bf8-7f9b-b7a5ddcbcf1e@samsung.com (mailing list archive)
State Not Applicable
Headers show

Commit Message

Hoegeun Kwon Feb. 22, 2017, 1:09 a.m. UTC 
The Samsung s6e3ha2 is a 5.7" 1440x2560 AMOLED panel connected
using MIPI-DSI interfaces.

Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
---
  .../bindings/display/panel/samsung,s6e3ha2.txt     | 28 
++++++++++++++++++++++
  1 file changed, 28 insertions(+)
  create mode 100644 
Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt

Comments

Javier Martinez Canillas March 6, 2017, 2:35 p.m. UTC | #1 
Hello Hoegeun,

On 02/21/2017 10:09 PM, Hoegeun Kwon wrote:
> The Samsung s6e3ha2 is a 5.7" 1440x2560 AMOLED panel connected
> using MIPI-DSI interfaces.
> 
> Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
> Acked-by: Rob Herring <robh@kernel.org>
> ---

Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>

Best regards,
diff mbox

Patch

diff --git 
a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt 
b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
new file mode 100644
index 0000000..18854f4
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
@@ -0,0 +1,28 @@ 
+Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel
+
+Required properties:
+  - compatible: "samsung,s6e3ha2"
+  - reg: the virtual channel number of a DSI peripheral
+  - vdd3-supply: I/O voltage supply
+  - vci-supply: voltage supply for analog circuits
+  - reset-gpios: a GPIO spec for the reset pin (active low)
+  - enable-gpios: a GPIO spec for the panel enable pin (active high)
+
+Optional properties:
+  - te-gpios: a GPIO spec for the tearing effect synchronization signal
+    gpio pin (active high)
+
+Example:
+&dsi {
+	...
+
+	panel@0 {
+		compatible = "samsung,s6e3ha2";
+		reg = <0>;
+		vdd3-supply = <&ldo27_reg>;
+		vci-supply = <&ldo28_reg>;
+		reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>;
+		te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>;
+	};
+};