| Message ID | 1488558513-23534-6-git-send-email-shashank.sharma@intel.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Fri, 2017-03-03 at 21:58 +0530, Shashank Sharma wrote: > Geminilake platform sports a native HDMI 2.0 controller, and is > capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec > mendates scrambling for these higher clocks, for reduced RF footprint. > > This patch checks if the monitor supports scrambling, and if required, > enables it during the modeset. > > V2: Addressed review comments from Ville: > - Do not track scrambling status in DRM layer, track somewhere in > driver like in intel_crtc_state. > - Don't talk to monitor at such a low layer, set monitor scrambling > in intel_enable_ddi() before enabling the port. > > V3: Addressed review comments from Jani > - In comments, function names, use "sink" instead of "monitor", > so that the implementation could be close to the language of > HDMI spec. > > V4: Addressed review comment from Maarten > - scrambling -> hdmi_scrambling > high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio > > V5: Addressed review comments from Ville and Ander > - Do not modifiy the crtc_state after compute_config. Move all > scrambling and tmds_clock_ratio calcutations to compute_config. > - While setting scrambling for source/sink, do not check the > conditions again, just go by the crtc_state flags. This will > simplyfy the condition checks. > > V6: Addressed review comments from Ville > - Do not add IS_GLK check in disable/enable function, instead add it > in compute_config, while setting state flags. > - Remove unnecessary paranthesis. > - Simplyfy handle_sink_scrambling function as suggested. > - Add readout code for scrambling status in get_ddi_config and add a > check for the same in pipe_config_compare. > > V7: Addressed review comments from Ander/Ville > - No separate function for source scrambling, make it inline > - Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK > - Do not add platform check while setting source scrambling > - Use pipe_config instead of crtc->config to set sink scrambling > - To readout scrambling status, Compare with SCRAMBLING_MASK > not any of its bits > - Remove platform check in intel_pipe_config_compare while checking > scrambling status > > Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> > --- > drivers/gpu/drm/i915/i915_reg.h | 7 +++++ > drivers/gpu/drm/i915/intel_ddi.c | 33 +++++++++++++++++++++++ > drivers/gpu/drm/i915/intel_display.c | 3 +++ > drivers/gpu/drm/i915/intel_drv.h | 10 +++++++ > drivers/gpu/drm/i915/intel_hdmi.c | 52 ++++++++++++++++++++++++++++++++++++ > 5 files changed, 105 insertions(+) > > diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h > index 4906ce4d..bfd988b 100644 > --- a/drivers/gpu/drm/i915/i915_reg.h > +++ b/drivers/gpu/drm/i915/i915_reg.h > @@ -7824,7 +7824,14 @@ enum { > #define TRANS_DDI_EDP_INPUT_B_ONOFF (5<<12) > #define TRANS_DDI_EDP_INPUT_C_ONOFF (6<<12) > #define TRANS_DDI_DP_VC_PAYLOAD_ALLOC (1<<8) > +#define TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE (1<<7) > +#define TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ (1<<6) > #define TRANS_DDI_BFI_ENABLE (1<<4) > +#define TRANS_DDI_HIGH_TMDS_CHAR_RATE (1<<4) > +#define TRANS_DDI_HDMI_SCRAMBLING (1<<0) > +#define TRANS_DDI_HDMI_SCRAMBLING_MASK (TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE \ > + | TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ \ > + | TRANS_DDI_HDMI_SCRAMBLING) > > /* DisplayPort Transport Control */ > #define _DP_TP_CTL_A 0x64040 > diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c > index a7c08d7..2159b2b 100644 > --- a/drivers/gpu/drm/i915/intel_ddi.c > +++ b/drivers/gpu/drm/i915/intel_ddi.c > @@ -1311,6 +1311,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc) > temp |= TRANS_DDI_MODE_SELECT_HDMI; > else > temp |= TRANS_DDI_MODE_SELECT_DVI; > + > + if (intel_crtc->config->hdmi_scrambling) > + temp |= TRANS_DDI_HDMI_SCRAMBLING_MASK; > + if (intel_crtc->config->hdmi_high_tmds_clock_ratio) > + temp |= TRANS_DDI_HIGH_TMDS_CHAR_RATE; > } else if (type == INTEL_OUTPUT_ANALOG) { > temp |= TRANS_DDI_MODE_SELECT_FDI; > temp |= (intel_crtc->config->fdi_lanes - 1) << 1; > @@ -1885,6 +1890,20 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder, > struct intel_digital_port *intel_dig_port = > enc_to_dig_port(encoder); > > + if (IS_GEMINILAKE(dev_priv)) { > + /* > + * GLK sports a native HDMI 2.0 controller. If required > + * clock rate is > 340 Mhz && scrambling is supported > + * by sink, enable scrambling before enabling the > + * HDMI 2.0 port. The sink can choose to disable the > + * scrambling if it doesn't detect a scrambled within > + * 100 ms. > + */ This comment seems out of place, it explains what's the effect of calling intel_hdmi_handle_sink_scrambling(). That should be in that function's kernel doc instead, which I now realize is missing. > + intel_hdmi_handle_sink_scrambling(intel_encoder, > + conn_state->connector, > + pipe_config, true); > + } > + > /* In HDMI/DVI mode, the port width, and swing/emphasis values > * are ignored so nothing special needs to be done besides > * enabling the port. > @@ -1917,6 +1936,14 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder, > if (old_crtc_state->has_audio) > intel_audio_codec_disable(intel_encoder); > > + if (type == INTEL_OUTPUT_HDMI) { > + struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc); > + > + intel_hdmi_handle_sink_scrambling(intel_encoder, > + old_conn_state->connector, > + intel_crtc->config, false); I'm wondering if this should old_crtc_state instead? If I remember right, crtc_state fields that are not explicitly preserved are zeroed, so handle_sink_scrambling() won't actually disable scrambling here. Also, there's an asymmetry between this and the enable path, since that checks for IS_GEMINILAKE() and this doesn't. Would it make sense to move the check into intel_hdmi_handle_sink_scrambling()? Ville? > + } > + > if (type == INTEL_OUTPUT_EDP) { > struct intel_dp *intel_dp = enc_to_intel_dp(encoder); > > @@ -2044,6 +2071,12 @@ void intel_ddi_get_config(struct intel_encoder *encoder, > > if (intel_hdmi->infoframe_enabled(&encoder->base, pipe_config)) > pipe_config->has_infoframe = true; > + > + if ((temp & TRANS_DDI_HDMI_SCRAMBLING_MASK) == > + TRANS_DDI_HDMI_SCRAMBLING_MASK) This is misaligned. Ander > + pipe_config->hdmi_scrambling = true; > + if (temp & TRANS_DDI_HIGH_TMDS_CHAR_RATE) > + pipe_config->hdmi_high_tmds_clock_ratio = true; > /* fall through */ > case TRANS_DDI_MODE_SELECT_DVI: > pipe_config->lane_count = 4; > diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c > index 99e8d9c..21d64c0 100644 > --- a/drivers/gpu/drm/i915/intel_display.c > +++ b/drivers/gpu/drm/i915/intel_display.c > @@ -11662,6 +11662,9 @@ static void __printf(3, 4) > if ((INTEL_GEN(dev_priv) < 8 && !IS_HASWELL(dev_priv)) || > IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) > PIPE_CONF_CHECK_I(limited_color_range); > + > + PIPE_CONF_CHECK_I(hdmi_scrambling); > + PIPE_CONF_CHECK_I(hdmi_high_tmds_clock_ratio); > PIPE_CONF_CHECK_I(has_infoframe); > > PIPE_CONF_CHECK_I(has_audio); > diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h > index e6fbbee..62fbeb2 100644 > --- a/drivers/gpu/drm/i915/intel_drv.h > +++ b/drivers/gpu/drm/i915/intel_drv.h > @@ -695,6 +695,12 @@ struct intel_crtc_state { > > /* Gamma mode programmed on the pipe */ > uint32_t gamma_mode; > + > + /* HDMI scrambling status (sink) */ > + bool hdmi_scrambling; > + > + /* HDMI High TMDS char rate ratio (sink) */ > + bool hdmi_high_tmds_clock_ratio; > }; > > struct vlv_wm_state { > @@ -1626,6 +1632,10 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port, > bool intel_hdmi_compute_config(struct intel_encoder *encoder, > struct intel_crtc_state *pipe_config, > struct drm_connector_state *conn_state); > +void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder, > + struct drm_connector *connector, > + struct intel_crtc_state *config, > + bool enable); > void intel_dp_dual_mode_set_tmds_output(struct intel_hdmi *hdmi, bool enable); > > > diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c > index c2184f7..c6e2398 100644 > --- a/drivers/gpu/drm/i915/intel_hdmi.c > +++ b/drivers/gpu/drm/i915/intel_hdmi.c > @@ -34,6 +34,7 @@ > #include <drm/drm_atomic_helper.h> > #include <drm/drm_crtc.h> > #include <drm/drm_edid.h> > +#include <drm/drm_scdc_helper.h> > #include "intel_drv.h" > #include <drm/i915_drm.h> > #include <drm/intel_lpe_audio.h> > @@ -1316,6 +1317,7 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder, > struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&encoder->base); > struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); > struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode; > + struct drm_scdc *scdc = &conn_state->connector->display_info.hdmi.scdc; > int clock_8bpc = pipe_config->base.adjusted_mode.crtc_clock; > int clock_12bpc = clock_8bpc * 3 / 2; > int desired_bpp; > @@ -1385,6 +1387,16 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder, > > pipe_config->lane_count = 4; > > + if (scdc->scrambling.supported && IS_GEMINILAKE(dev_priv)) { > + if (scdc->scrambling.low_rates) > + pipe_config->hdmi_scrambling = true; > + > + if (pipe_config->port_clock > 340000) { > + pipe_config->hdmi_scrambling = true; > + pipe_config->hdmi_high_tmds_clock_ratio = true; > + } > + } > + > return true; > } > > @@ -1794,6 +1806,46 @@ static void intel_hdmi_destroy(struct drm_connector *connector) > intel_hdmi->aspect_ratio = HDMI_PICTURE_ASPECT_NONE; > } > > +void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder, > + struct drm_connector *connector, > + struct intel_crtc_state *config, > + bool enable) > +{ > + struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&intel_encoder->base); > + struct drm_i915_private *dev_priv = connector->dev->dev_private; > + struct drm_scrambling *scrambling = > + &connector->display_info.hdmi.scdc.scrambling; > + struct i2c_adapter *adptr = intel_gmbus_get_adapter(dev_priv, > + intel_hdmi->ddc_bus); > + bool ret; > + > + if (!scrambling->supported) > + return; > + > + DRM_DEBUG_KMS("Setting sink scrambling for enc:%s connector:%s\n", > + intel_encoder->base.name, connector->name); > + > + if (config->hdmi_high_tmds_clock_ratio) { > + /* Set TMDS bit clock ratio to 1/40 or 1/10 */ > + ret = drm_scdc_set_high_tmds_clock_ratio(adptr, enable); > + if (!ret) { > + DRM_ERROR("Set TMDS ratio failed\n"); > + return; > + } > + } > + > + if (config->hdmi_scrambling) { > + /* Enable/disable sink scrambling */ > + ret = drm_scdc_set_scrambling(adptr, enable); > + if (!ret) { > + DRM_ERROR("Set sink scrambling failed\n"); > + return; > + } > + } > + > + DRM_DEBUG_KMS("sink scrambling handled\n"); > +} > + > static u8 intel_hdmi_ddc_pin(struct drm_i915_private *dev_priv, > enum port port) > {
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index 4906ce4d..bfd988b 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -7824,7 +7824,14 @@ enum { #define TRANS_DDI_EDP_INPUT_B_ONOFF (5<<12) #define TRANS_DDI_EDP_INPUT_C_ONOFF (6<<12) #define TRANS_DDI_DP_VC_PAYLOAD_ALLOC (1<<8) +#define TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE (1<<7) +#define TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ (1<<6) #define TRANS_DDI_BFI_ENABLE (1<<4) +#define TRANS_DDI_HIGH_TMDS_CHAR_RATE (1<<4) +#define TRANS_DDI_HDMI_SCRAMBLING (1<<0) +#define TRANS_DDI_HDMI_SCRAMBLING_MASK (TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE \ + | TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ \ + | TRANS_DDI_HDMI_SCRAMBLING) /* DisplayPort Transport Control */ #define _DP_TP_CTL_A 0x64040 diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c index a7c08d7..2159b2b 100644 --- a/drivers/gpu/drm/i915/intel_ddi.c +++ b/drivers/gpu/drm/i915/intel_ddi.c @@ -1311,6 +1311,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc) temp |= TRANS_DDI_MODE_SELECT_HDMI; else temp |= TRANS_DDI_MODE_SELECT_DVI; + + if (intel_crtc->config->hdmi_scrambling) + temp |= TRANS_DDI_HDMI_SCRAMBLING_MASK; + if (intel_crtc->config->hdmi_high_tmds_clock_ratio) + temp |= TRANS_DDI_HIGH_TMDS_CHAR_RATE; } else if (type == INTEL_OUTPUT_ANALOG) { temp |= TRANS_DDI_MODE_SELECT_FDI; temp |= (intel_crtc->config->fdi_lanes - 1) << 1; @@ -1885,6 +1890,20 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder, struct intel_digital_port *intel_dig_port = enc_to_dig_port(encoder); + if (IS_GEMINILAKE(dev_priv)) { + /* + * GLK sports a native HDMI 2.0 controller. If required + * clock rate is > 340 Mhz && scrambling is supported + * by sink, enable scrambling before enabling the + * HDMI 2.0 port. The sink can choose to disable the + * scrambling if it doesn't detect a scrambled within + * 100 ms. + */ + intel_hdmi_handle_sink_scrambling(intel_encoder, + conn_state->connector, + pipe_config, true); + } + /* In HDMI/DVI mode, the port width, and swing/emphasis values * are ignored so nothing special needs to be done besides * enabling the port. @@ -1917,6 +1936,14 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder, if (old_crtc_state->has_audio) intel_audio_codec_disable(intel_encoder); + if (type == INTEL_OUTPUT_HDMI) { + struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc); + + intel_hdmi_handle_sink_scrambling(intel_encoder, + old_conn_state->connector, + intel_crtc->config, false); + } + if (type == INTEL_OUTPUT_EDP) { struct intel_dp *intel_dp = enc_to_intel_dp(encoder); @@ -2044,6 +2071,12 @@ void intel_ddi_get_config(struct intel_encoder *encoder, if (intel_hdmi->infoframe_enabled(&encoder->base, pipe_config)) pipe_config->has_infoframe = true; + + if ((temp & TRANS_DDI_HDMI_SCRAMBLING_MASK) == + TRANS_DDI_HDMI_SCRAMBLING_MASK) + pipe_config->hdmi_scrambling = true; + if (temp & TRANS_DDI_HIGH_TMDS_CHAR_RATE) + pipe_config->hdmi_high_tmds_clock_ratio = true; /* fall through */ case TRANS_DDI_MODE_SELECT_DVI: pipe_config->lane_count = 4; diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 99e8d9c..21d64c0 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -11662,6 +11662,9 @@ static void __printf(3, 4) if ((INTEL_GEN(dev_priv) < 8 && !IS_HASWELL(dev_priv)) || IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) PIPE_CONF_CHECK_I(limited_color_range); + + PIPE_CONF_CHECK_I(hdmi_scrambling); + PIPE_CONF_CHECK_I(hdmi_high_tmds_clock_ratio); PIPE_CONF_CHECK_I(has_infoframe); PIPE_CONF_CHECK_I(has_audio); diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h index e6fbbee..62fbeb2 100644 --- a/drivers/gpu/drm/i915/intel_drv.h +++ b/drivers/gpu/drm/i915/intel_drv.h @@ -695,6 +695,12 @@ struct intel_crtc_state { /* Gamma mode programmed on the pipe */ uint32_t gamma_mode; + + /* HDMI scrambling status (sink) */ + bool hdmi_scrambling; + + /* HDMI High TMDS char rate ratio (sink) */ + bool hdmi_high_tmds_clock_ratio; }; struct vlv_wm_state { @@ -1626,6 +1632,10 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port, bool intel_hdmi_compute_config(struct intel_encoder *encoder, struct intel_crtc_state *pipe_config, struct drm_connector_state *conn_state); +void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder, + struct drm_connector *connector, + struct intel_crtc_state *config, + bool enable); void intel_dp_dual_mode_set_tmds_output(struct intel_hdmi *hdmi, bool enable); diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c index c2184f7..c6e2398 100644 --- a/drivers/gpu/drm/i915/intel_hdmi.c +++ b/drivers/gpu/drm/i915/intel_hdmi.c @@ -34,6 +34,7 @@ #include <drm/drm_atomic_helper.h> #include <drm/drm_crtc.h> #include <drm/drm_edid.h> +#include <drm/drm_scdc_helper.h> #include "intel_drv.h" #include <drm/i915_drm.h> #include <drm/intel_lpe_audio.h> @@ -1316,6 +1317,7 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder, struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&encoder->base); struct drm_i915_private *dev_priv = to_i915(encoder->base.dev); struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode; + struct drm_scdc *scdc = &conn_state->connector->display_info.hdmi.scdc; int clock_8bpc = pipe_config->base.adjusted_mode.crtc_clock; int clock_12bpc = clock_8bpc * 3 / 2; int desired_bpp; @@ -1385,6 +1387,16 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder, pipe_config->lane_count = 4; + if (scdc->scrambling.supported && IS_GEMINILAKE(dev_priv)) { + if (scdc->scrambling.low_rates) + pipe_config->hdmi_scrambling = true; + + if (pipe_config->port_clock > 340000) { + pipe_config->hdmi_scrambling = true; + pipe_config->hdmi_high_tmds_clock_ratio = true; + } + } + return true; } @@ -1794,6 +1806,46 @@ static void intel_hdmi_destroy(struct drm_connector *connector) intel_hdmi->aspect_ratio = HDMI_PICTURE_ASPECT_NONE; } +void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder, + struct drm_connector *connector, + struct intel_crtc_state *config, + bool enable) +{ + struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&intel_encoder->base); + struct drm_i915_private *dev_priv = connector->dev->dev_private; + struct drm_scrambling *scrambling = + &connector->display_info.hdmi.scdc.scrambling; + struct i2c_adapter *adptr = intel_gmbus_get_adapter(dev_priv, + intel_hdmi->ddc_bus); + bool ret; + + if (!scrambling->supported) + return; + + DRM_DEBUG_KMS("Setting sink scrambling for enc:%s connector:%s\n", + intel_encoder->base.name, connector->name); + + if (config->hdmi_high_tmds_clock_ratio) { + /* Set TMDS bit clock ratio to 1/40 or 1/10 */ + ret = drm_scdc_set_high_tmds_clock_ratio(adptr, enable); + if (!ret) { + DRM_ERROR("Set TMDS ratio failed\n"); + return; + } + } + + if (config->hdmi_scrambling) { + /* Enable/disable sink scrambling */ + ret = drm_scdc_set_scrambling(adptr, enable); + if (!ret) { + DRM_ERROR("Set sink scrambling failed\n"); + return; + } + } + + DRM_DEBUG_KMS("sink scrambling handled\n"); +} + static u8 intel_hdmi_ddc_pin(struct drm_i915_private *dev_priv, enum port port) {
Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint. This patch checks if the monitor supports scrambling, and if required, enables it during the modeset. V2: Addressed review comments from Ville: - Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state. - Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port. V3: Addressed review comments from Jani - In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec. V4: Addressed review comment from Maarten - scrambling -> hdmi_scrambling high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio V5: Addressed review comments from Ville and Ander - Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config. - While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks. V6: Addressed review comments from Ville - Do not add IS_GLK check in disable/enable function, instead add it in compute_config, while setting state flags. - Remove unnecessary paranthesis. - Simplyfy handle_sink_scrambling function as suggested. - Add readout code for scrambling status in get_ddi_config and add a check for the same in pipe_config_compare. V7: Addressed review comments from Ander/Ville - No separate function for source scrambling, make it inline - Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK - Do not add platform check while setting source scrambling - Use pipe_config instead of crtc->config to set sink scrambling - To readout scrambling status, Compare with SCRAMBLING_MASK not any of its bits - Remove platform check in intel_pipe_config_compare while checking scrambling status Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> --- drivers/gpu/drm/i915/i915_reg.h | 7 +++++ drivers/gpu/drm/i915/intel_ddi.c | 33 +++++++++++++++++++++++ drivers/gpu/drm/i915/intel_display.c | 3 +++ drivers/gpu/drm/i915/intel_drv.h | 10 +++++++ drivers/gpu/drm/i915/intel_hdmi.c | 52 ++++++++++++++++++++++++++++++++++++ 5 files changed, 105 insertions(+)