| Message ID | 20170712010255.26855-3-stephen.boyd@linaro.org (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Delegated to: | Andy Gross |
| Headers | show |
On 2017-07-12 03:02, Stephen Boyd wrote: > On the db410c 96boards platform we have a TC7USB40MU on the board > to mux the D+/D- lines coming from the controller between a micro > usb "device" port and a USB hub for "host" roles[1]. During a > role switch, we need to toggle this mux to forward the D+/D- > lines to either the port or the hub. Add the necessary code to do > the role switch in chipidea core via the generic mux framework. > Board configurations like on db410c are expected to change roles > via the sysfs API described in > Documentation/ABI/testing/sysfs-platform-chipidea-usb2. > > [1] https://github.com/96boards/documentation/raw/master/ConsumerEdition/DragonBoard-410c/HardwareDocs/Schematics_DragonBoard.pdf > > Cc: Peter Rosin <peda@axentia.se> > Cc: Peter Chen <peter.chen@nxp.com> > Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> > Cc: <devicetree@vger.kernel.org> > Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> > --- > Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt | 8 ++++++++ > drivers/usb/chipidea/core.c | 17 +++++++++++++++++ > drivers/usb/chipidea/host.c | 10 ++++++++++ > drivers/usb/chipidea/udc.c | 11 +++++++++++ > include/linux/usb/chipidea.h | 14 ++++++++++++++ > 5 files changed, 60 insertions(+) > > diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt > index 0e03344e2e8b..96ce81d975d5 100644 > --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt > +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt > @@ -76,6 +76,11 @@ Optional properties: > needs to make sure it does not send more than 90% > maximum_periodic_data_per_frame. The use case is multiple transactions, but > less frame rate. > +- mux-controls: The mux control for toggling host/device output of this > + controller. > +- mux-control-names: Shall be "usb_switch" if mux-controls is specified. > +- usb-switch-states: Two u32's defining the state to set on the mux for the > + host mode and device modes respectively. > > i.mx specific properties > - fsl,usbmisc: phandler of non-core register device, with one > @@ -102,4 +107,7 @@ Example: > rx-burst-size-dword = <0x10>; > extcon = <0>, <&usb_id>; > phy-clkgate-delay-us = <400>; > + mux-controls = <&usb_switch>; > + mux-control-names = "usb_switch"; > + usb-switch-states = <0>, <1>; I don't see the need for usb-switch-states? Just assume states 0/1 and if someone later needs some other states, make them add a property that overrides the defaults. Just document that 0 is host and 1 is device. > }; > diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c > index b17ed3a9a304..6531d771f296 100644 > --- a/drivers/usb/chipidea/core.c > +++ b/drivers/usb/chipidea/core.c > @@ -64,6 +64,7 @@ > #include <linux/of.h> > #include <linux/regulator/consumer.h> > #include <linux/usb/ehci_def.h> > +#include <linux/mux/consumer.h> > > #include "ci.h" > #include "udc.h" > @@ -606,6 +607,7 @@ static int ci_get_platdata(struct device *dev, > { > struct extcon_dev *ext_vbus, *ext_id; > struct ci_hdrc_cable *cable; > + struct ci_hdrc_switch *usb_switch; > int ret; > > if (!platdata->phy_mode) > @@ -690,6 +692,21 @@ static int ci_get_platdata(struct device *dev, > if (of_find_property(dev->of_node, "non-zero-ttctrl-ttha", NULL)) > platdata->flags |= CI_HDRC_SET_NON_ZERO_TTHA; > > + if (IS_ENABLED(CONFIG_MULTIPLEXER)) { > + usb_switch = &platdata->usb_switch; > + usb_switch->mux = devm_mux_control_get(dev, "usb_switch"); > + if (!IS_ERR(usb_switch->mux)) { > + if (of_property_read_u32_index(dev->of_node, > + "usb-switch-states", > + 0, &usb_switch->device)) > + return -EINVAL; > + if (of_property_read_u32_index(dev->of_node, > + "usb-switch-states", > + 1, &usb_switch->host)) > + return -EINVAL; > + } > + } > + > ext_id = ERR_PTR(-ENODEV); > ext_vbus = ERR_PTR(-ENODEV); > if (of_property_read_bool(dev->of_node, "extcon")) { > diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c > index 18cb8e46262d..9fd23ecc2da3 100644 > --- a/drivers/usb/chipidea/host.c > +++ b/drivers/usb/chipidea/host.c > @@ -25,6 +25,7 @@ > #include <linux/usb/hcd.h> > #include <linux/usb/chipidea.h> > #include <linux/regulator/consumer.h> > +#include <linux/mux/consumer.h> > > #include "../host/ehci.h" > > @@ -123,6 +124,13 @@ static int host_start(struct ci_hdrc *ci) > if (usb_disabled()) > return -ENODEV; > > + if (!IS_ERR(ci->platdata->usb_switch.mux)) { > + ret = mux_control_select(ci->platdata->usb_switch.mux, > + ci->platdata->usb_switch.host); > + if (ret) > + return ret; > + } > + You *must* call mux_control_deselect to clean up if there is a failure later in host_start. Is that handled in some non-obvious way? > hcd = __usb_create_hcd(&ci_ehci_hc_driver, ci->dev->parent, > ci->dev, dev_name(ci->dev), NULL); > if (!hcd) > @@ -205,6 +213,8 @@ static void host_stop(struct ci_hdrc *ci) > if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci) && > (ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON)) > regulator_disable(ci->platdata->reg_vbus); > + if (!IS_ERR(ci->platdata->usb_switch.mux)) > + mux_control_deselect(ci->platdata->usb_switch.mux); > } > ci->hcd = NULL; > ci->otg.host = NULL; > diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c > index d68b125796f9..ab3355905740 100644 > --- a/drivers/usb/chipidea/udc.c > +++ b/drivers/usb/chipidea/udc.c > @@ -22,6 +22,7 @@ > #include <linux/usb/gadget.h> > #include <linux/usb/otg-fsm.h> > #include <linux/usb/chipidea.h> > +#include <linux/mux/consumer.h> > > #include "ci.h" > #include "udc.h" > @@ -1899,6 +1900,13 @@ static int udc_start(struct ci_hdrc *ci) > ci->gadget.name = ci->platdata->name; > ci->gadget.otg_caps = otg_caps; > > + if (!IS_ERR(ci->platdata->usb_switch.mux)) { > + retval = mux_control_select(ci->platdata->usb_switch.mux, > + ci->platdata->usb_switch.device); > + if (retval) > + return retval; > + } > + Dito. Cheers, peda > if (ci->is_otg && (otg_caps->hnp_support || otg_caps->srp_support || > otg_caps->adp_support)) > ci->gadget.is_otg = 1; > @@ -1982,6 +1990,9 @@ static void udc_id_switch_for_host(struct ci_hdrc *ci) > hw_write_otgsc(ci, OTGSC_BSVIE | OTGSC_BSVIS, OTGSC_BSVIS); > > ci->vbus_active = 0; > + > + if (!IS_ERR(ci->platdata->usb_switch.mux)) > + mux_control_deselect(ci->platdata->usb_switch.mux); > } > > /** > diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h > index c5fdfcf99828..559bd470b8c0 100644 > --- a/include/linux/usb/chipidea.h > +++ b/include/linux/usb/chipidea.h > @@ -9,6 +9,7 @@ > #include <linux/usb/otg.h> > > struct ci_hdrc; > +struct mux_control; > > /** > * struct ci_hdrc_cable - structure for external connector cable state tracking > @@ -29,6 +30,18 @@ struct ci_hdrc_cable { > struct notifier_block nb; > }; > > +/** > + * struct ci_hdrc_switch - structure for usb mux control > + * @mux: mux to set @host state or @device state on during role switch > + * @host: Value to set for mux to connect D+/D- to host D+/D- lines > + * @device: Value to set for mux to connect D+/D- to device D+/D- lines > + */ > +struct ci_hdrc_switch { > + struct mux_control *mux; > + int host; > + int device; > +}; > + > struct ci_hdrc_platform_data { > const char *name; > /* offset of the capability registers */ > @@ -74,6 +87,7 @@ struct ci_hdrc_platform_data { > /* VBUS and ID signal state tracking, using extcon framework */ > struct ci_hdrc_cable vbus_extcon; > struct ci_hdrc_cable id_extcon; > + struct ci_hdrc_switch usb_switch; > u32 phy_clkgate_delay_us; > }; > > -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoting Peter Rosin (2017-07-11 23:45:24) > On 2017-07-12 03:02, Stephen Boyd wrote: > > @@ -102,4 +107,7 @@ Example: > > rx-burst-size-dword = <0x10>; > > extcon = <0>, <&usb_id>; > > phy-clkgate-delay-us = <400>; > > + mux-controls = <&usb_switch>; > > + mux-control-names = "usb_switch"; > > + usb-switch-states = <0>, <1>; > > I don't see the need for usb-switch-states? Just assume states 0/1 and > if someone later needs some other states, make them add a property that > overrides the defaults. Just document that 0 is host and 1 is device. > Fine by me. Rob H do you agree? > > diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c > > index 18cb8e46262d..9fd23ecc2da3 100644 > > --- a/drivers/usb/chipidea/host.c > > +++ b/drivers/usb/chipidea/host.c > > @@ -25,6 +25,7 @@ > > #include <linux/usb/hcd.h> > > #include <linux/usb/chipidea.h> > > #include <linux/regulator/consumer.h> > > +#include <linux/mux/consumer.h> > > > > #include "../host/ehci.h" > > > > @@ -123,6 +124,13 @@ static int host_start(struct ci_hdrc *ci) > > if (usb_disabled()) > > return -ENODEV; > > > > + if (!IS_ERR(ci->platdata->usb_switch.mux)) { > > + ret = mux_control_select(ci->platdata->usb_switch.mux, > > + ci->platdata->usb_switch.host); > > + if (ret) > > + return ret; > > + } > > + > > You *must* call mux_control_deselect to clean up if there is a failure > later in host_start. Is that handled in some non-obvious way? Good catch. Thanks. I'll add in the unwinding on the error path. -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, Jul 13, 2017 at 03:29:43PM -0700, Stephen Boyd wrote: > Quoting Peter Rosin (2017-07-11 23:45:24) > > On 2017-07-12 03:02, Stephen Boyd wrote: > > > @@ -102,4 +107,7 @@ Example: > > > rx-burst-size-dword = <0x10>; > > > extcon = <0>, <&usb_id>; > > > phy-clkgate-delay-us = <400>; > > > + mux-controls = <&usb_switch>; > > > + mux-control-names = "usb_switch"; Pointless to have a name when there is only 1. > > > + usb-switch-states = <0>, <1>; > > > > I don't see the need for usb-switch-states? Just assume states 0/1 and > > if someone later needs some other states, make them add a property that > > overrides the defaults. Just document that 0 is host and 1 is device. > > > > Fine by me. Rob H do you agree? Yes. Rob -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 0e03344e2e8b..96ce81d975d5 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -76,6 +76,11 @@ Optional properties: needs to make sure it does not send more than 90% maximum_periodic_data_per_frame. The use case is multiple transactions, but less frame rate. +- mux-controls: The mux control for toggling host/device output of this + controller. +- mux-control-names: Shall be "usb_switch" if mux-controls is specified. +- usb-switch-states: Two u32's defining the state to set on the mux for the + host mode and device modes respectively. i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one @@ -102,4 +107,7 @@ Example: rx-burst-size-dword = <0x10>; extcon = <0>, <&usb_id>; phy-clkgate-delay-us = <400>; + mux-controls = <&usb_switch>; + mux-control-names = "usb_switch"; + usb-switch-states = <0>, <1>; }; diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c index b17ed3a9a304..6531d771f296 100644 --- a/drivers/usb/chipidea/core.c +++ b/drivers/usb/chipidea/core.c @@ -64,6 +64,7 @@ #include <linux/of.h> #include <linux/regulator/consumer.h> #include <linux/usb/ehci_def.h> +#include <linux/mux/consumer.h> #include "ci.h" #include "udc.h" @@ -606,6 +607,7 @@ static int ci_get_platdata(struct device *dev, { struct extcon_dev *ext_vbus, *ext_id; struct ci_hdrc_cable *cable; + struct ci_hdrc_switch *usb_switch; int ret; if (!platdata->phy_mode) @@ -690,6 +692,21 @@ static int ci_get_platdata(struct device *dev, if (of_find_property(dev->of_node, "non-zero-ttctrl-ttha", NULL)) platdata->flags |= CI_HDRC_SET_NON_ZERO_TTHA; + if (IS_ENABLED(CONFIG_MULTIPLEXER)) { + usb_switch = &platdata->usb_switch; + usb_switch->mux = devm_mux_control_get(dev, "usb_switch"); + if (!IS_ERR(usb_switch->mux)) { + if (of_property_read_u32_index(dev->of_node, + "usb-switch-states", + 0, &usb_switch->device)) + return -EINVAL; + if (of_property_read_u32_index(dev->of_node, + "usb-switch-states", + 1, &usb_switch->host)) + return -EINVAL; + } + } + ext_id = ERR_PTR(-ENODEV); ext_vbus = ERR_PTR(-ENODEV); if (of_property_read_bool(dev->of_node, "extcon")) { diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c index 18cb8e46262d..9fd23ecc2da3 100644 --- a/drivers/usb/chipidea/host.c +++ b/drivers/usb/chipidea/host.c @@ -25,6 +25,7 @@ #include <linux/usb/hcd.h> #include <linux/usb/chipidea.h> #include <linux/regulator/consumer.h> +#include <linux/mux/consumer.h> #include "../host/ehci.h" @@ -123,6 +124,13 @@ static int host_start(struct ci_hdrc *ci) if (usb_disabled()) return -ENODEV; + if (!IS_ERR(ci->platdata->usb_switch.mux)) { + ret = mux_control_select(ci->platdata->usb_switch.mux, + ci->platdata->usb_switch.host); + if (ret) + return ret; + } + hcd = __usb_create_hcd(&ci_ehci_hc_driver, ci->dev->parent, ci->dev, dev_name(ci->dev), NULL); if (!hcd) @@ -205,6 +213,8 @@ static void host_stop(struct ci_hdrc *ci) if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci) && (ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON)) regulator_disable(ci->platdata->reg_vbus); + if (!IS_ERR(ci->platdata->usb_switch.mux)) + mux_control_deselect(ci->platdata->usb_switch.mux); } ci->hcd = NULL; ci->otg.host = NULL; diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c index d68b125796f9..ab3355905740 100644 --- a/drivers/usb/chipidea/udc.c +++ b/drivers/usb/chipidea/udc.c @@ -22,6 +22,7 @@ #include <linux/usb/gadget.h> #include <linux/usb/otg-fsm.h> #include <linux/usb/chipidea.h> +#include <linux/mux/consumer.h> #include "ci.h" #include "udc.h" @@ -1899,6 +1900,13 @@ static int udc_start(struct ci_hdrc *ci) ci->gadget.name = ci->platdata->name; ci->gadget.otg_caps = otg_caps; + if (!IS_ERR(ci->platdata->usb_switch.mux)) { + retval = mux_control_select(ci->platdata->usb_switch.mux, + ci->platdata->usb_switch.device); + if (retval) + return retval; + } + if (ci->is_otg && (otg_caps->hnp_support || otg_caps->srp_support || otg_caps->adp_support)) ci->gadget.is_otg = 1; @@ -1982,6 +1990,9 @@ static void udc_id_switch_for_host(struct ci_hdrc *ci) hw_write_otgsc(ci, OTGSC_BSVIE | OTGSC_BSVIS, OTGSC_BSVIS); ci->vbus_active = 0; + + if (!IS_ERR(ci->platdata->usb_switch.mux)) + mux_control_deselect(ci->platdata->usb_switch.mux); } /** diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h index c5fdfcf99828..559bd470b8c0 100644 --- a/include/linux/usb/chipidea.h +++ b/include/linux/usb/chipidea.h @@ -9,6 +9,7 @@ #include <linux/usb/otg.h> struct ci_hdrc; +struct mux_control; /** * struct ci_hdrc_cable - structure for external connector cable state tracking @@ -29,6 +30,18 @@ struct ci_hdrc_cable { struct notifier_block nb; }; +/** + * struct ci_hdrc_switch - structure for usb mux control + * @mux: mux to set @host state or @device state on during role switch + * @host: Value to set for mux to connect D+/D- to host D+/D- lines + * @device: Value to set for mux to connect D+/D- to device D+/D- lines + */ +struct ci_hdrc_switch { + struct mux_control *mux; + int host; + int device; +}; + struct ci_hdrc_platform_data { const char *name; /* offset of the capability registers */ @@ -74,6 +87,7 @@ struct ci_hdrc_platform_data { /* VBUS and ID signal state tracking, using extcon framework */ struct ci_hdrc_cable vbus_extcon; struct ci_hdrc_cable id_extcon; + struct ci_hdrc_switch usb_switch; u32 phy_clkgate_delay_us; };
On the db410c 96boards platform we have a TC7USB40MU on the board to mux the D+/D- lines coming from the controller between a micro usb "device" port and a USB hub for "host" roles[1]. During a role switch, we need to toggle this mux to forward the D+/D- lines to either the port or the hub. Add the necessary code to do the role switch in chipidea core via the generic mux framework. Board configurations like on db410c are expected to change roles via the sysfs API described in Documentation/ABI/testing/sysfs-platform-chipidea-usb2. [1] https://github.com/96boards/documentation/raw/master/ConsumerEdition/DragonBoard-410c/HardwareDocs/Schematics_DragonBoard.pdf Cc: Peter Rosin <peda@axentia.se> Cc: Peter Chen <peter.chen@nxp.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <devicetree@vger.kernel.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> --- Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt | 8 ++++++++ drivers/usb/chipidea/core.c | 17 +++++++++++++++++ drivers/usb/chipidea/host.c | 10 ++++++++++ drivers/usb/chipidea/udc.c | 11 +++++++++++ include/linux/usb/chipidea.h | 14 ++++++++++++++ 5 files changed, 60 insertions(+)