| Message ID | 1500287629-23703-5-git-send-email-todor.tomov@linaro.org (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Delegated to: | Andy Gross |
| Headers | show |
Hi Todor, On Mon, Jul 17, 2017 at 01:33:30PM +0300, Todor Tomov wrote: > Add DT binding document for Qualcomm Camera subsystem driver. > > CC: Rob Herring <robh+dt@kernel.org> > CC: devicetree@vger.kernel.org > Signed-off-by: Todor Tomov <todor.tomov@linaro.org> > --- > .../devicetree/bindings/media/qcom,camss.txt | 191 +++++++++++++++++++++ > 1 file changed, 191 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/qcom,camss.txt > > diff --git a/Documentation/devicetree/bindings/media/qcom,camss.txt b/Documentation/devicetree/bindings/media/qcom,camss.txt > new file mode 100644 > index 0000000..f698498 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/qcom,camss.txt > @@ -0,0 +1,191 @@ > +Qualcomm Camera Subsystem > + > +* Properties > + > +- compatible: > + Usage: required > + Value type: <stringlist> > + Definition: Should contain: > + - "qcom,msm8916-camss" > +- reg: > + Usage: required > + Value type: <prop-encoded-array> > + Definition: Register ranges as listed in the reg-names property. > +- reg-names: > + Usage: required > + Value type: <stringlist> > + Definition: Should contain the following entries: > + - "csiphy0" > + - "csiphy0_clk_mux" > + - "csiphy1" > + - "csiphy1_clk_mux" > + - "csid0" > + - "csid1" > + - "ispif" > + - "csi_clk_mux" > + - "vfe0" > +- interrupts: > + Usage: required > + Value type: <prop-encoded-array> > + Definition: Interrupts as listed in the interrupt-names property. > +- interrupt-names: > + Usage: required > + Value type: <stringlist> > + Definition: Should contain the following entries: > + - "csiphy0" > + - "csiphy1" > + - "csid0" > + - "csid1" > + - "ispif" > + - "vfe0" > +- power-domains: > + Usage: required > + Value type: <prop-encoded-array> > + Definition: A phandle and power domain specifier pairs to the > + power domain which is responsible for collapsing > + and restoring power to the peripheral. > +- clocks: > + Usage: required > + Value type: <prop-encoded-array> > + Definition: A list of phandle and clock specifier pairs as listed > + in clock-names property. > +- clock-names: > + Usage: required > + Value type: <stringlist> > + Definition: Should contain the following entries: > + - "camss_top_ahb" > + - "ispif_ahb" > + - "csiphy0_timer" > + - "csiphy1_timer" > + - "csi0_ahb" > + - "csi0" > + - "csi0_phy" > + - "csi0_pix" > + - "csi0_rdi" > + - "csi1_ahb" > + - "csi1" > + - "csi1_phy" > + - "csi1_pix" > + - "csi1_rdi" > + - "camss_ahb" > + - "camss_vfe_vfe" > + - "camss_csi_vfe" > + - "iface" > + - "bus" > +- vdda-supply: > + Usage: required > + Value type: <phandle> > + Definition: A phandle to voltage supply for CSI2. > +- iommus: > + Usage: required > + Value type: <prop-encoded-array> > + Definition: A list of phandle and IOMMU specifier pairs. > + > +* Nodes > + > +- ports: > + Usage: required > + Definition: As described in video-interfaces.txt in same directory. > + Properties: > + - reg: > + Usage: required > + Value type: <u32> > + Definition: Selects CSI2 PHY interface - PHY0 or PHY1. > + Endpoint node properties: > + - clock-lanes: > + Usage: required > + Value type: <u32> > + Definition: The clock lane. > + - data-lanes: > + Usage: required > + Value type: <prop-encoded-array> > + Definition: An array of data lanes. > + > +* An Example > + > + camss: camss@1b00000 { > + compatible = "qcom,msm8916-camss"; > + reg = <0x1b0ac00 0x200>, > + <0x1b00030 0x4>, > + <0x1b0b000 0x200>, > + <0x1b00038 0x4>, > + <0x1b08000 0x100>, > + <0x1b08400 0x100>, > + <0x1b0a000 0x500>, > + <0x1b00020 0x10>, > + <0x1b10000 0x1000>; > + reg-names = "csiphy0", > + "csiphy0_clk_mux", > + "csiphy1", > + "csiphy1_clk_mux", > + "csid0", > + "csid1", > + "ispif", > + "csi_clk_mux", > + "vfe0"; > + interrupts = <GIC_SPI 78 0>, > + <GIC_SPI 79 0>, > + <GIC_SPI 51 0>, > + <GIC_SPI 52 0>, > + <GIC_SPI 55 0>, > + <GIC_SPI 57 0>; > + interrupt-names = "csiphy0", > + "csiphy1", > + "csid0", > + "csid1", > + "ispif", > + "vfe0"; > + power-domains = <&gcc VFE_GDSC>; > + clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>, > + <&gcc GCC_CAMSS_ISPIF_AHB_CLK>, > + <&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>, > + <&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>, > + <&gcc GCC_CAMSS_CSI0_AHB_CLK>, > + <&gcc GCC_CAMSS_CSI0_CLK>, > + <&gcc GCC_CAMSS_CSI0PHY_CLK>, > + <&gcc GCC_CAMSS_CSI0PIX_CLK>, > + <&gcc GCC_CAMSS_CSI0RDI_CLK>, > + <&gcc GCC_CAMSS_CSI1_AHB_CLK>, > + <&gcc GCC_CAMSS_CSI1_CLK>, > + <&gcc GCC_CAMSS_CSI1PHY_CLK>, > + <&gcc GCC_CAMSS_CSI1PIX_CLK>, > + <&gcc GCC_CAMSS_CSI1RDI_CLK>, > + <&gcc GCC_CAMSS_AHB_CLK>, > + <&gcc GCC_CAMSS_VFE0_CLK>, > + <&gcc GCC_CAMSS_CSI_VFE0_CLK>, > + <&gcc GCC_CAMSS_VFE_AHB_CLK>, > + <&gcc GCC_CAMSS_VFE_AXI_CLK>; > + clock-names = "camss_top_ahb", > + "ispif_ahb", > + "csiphy0_timer", > + "csiphy1_timer", > + "csi0_ahb", > + "csi0", > + "csi0_phy", > + "csi0_pix", > + "csi0_rdi", > + "csi1_ahb", > + "csi1", > + "csi1_phy", > + "csi1_pix", > + "csi1_rdi", > + "camss_ahb", > + "camss_vfe_vfe", > + "camss_csi_vfe", > + "iface", > + "bus"; > + vdda-supply = <&pm8916_l2>; > + iommus = <&apps_iommu 3>; > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + port@0 { > + reg = <0>; > + csiphy0_ep: endpoint { > + clock-lanes = <1>; > + data-lanes = <0 2>; Do you support lane mapping? The values suggest "yes". That's something I could improve in the documentation: if lane mapping isn't supported, then the clock lane should be 0 and the data lanes from 1 to n. Is the split of the lanes between the ports static and specific to the hardware? > + remote-endpoint = <&ov5645_ep>; > + }; > + }; > + }; > + };
On Mon, Jul 17, 2017 at 01:33:30PM +0300, Todor Tomov wrote: > Add DT binding document for Qualcomm Camera subsystem driver. > > CC: Rob Herring <robh+dt@kernel.org> > CC: devicetree@vger.kernel.org > Signed-off-by: Todor Tomov <todor.tomov@linaro.org> > --- > .../devicetree/bindings/media/qcom,camss.txt | 191 +++++++++++++++++++++ > 1 file changed, 191 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/qcom,camss.txt > > diff --git a/Documentation/devicetree/bindings/media/qcom,camss.txt b/Documentation/devicetree/bindings/media/qcom,camss.txt > new file mode 100644 > index 0000000..f698498 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/qcom,camss.txt qcom,camss.txt or qcom,camss-8x16.txt?
On Mon, Jul 17, 2017 at 01:33:30PM +0300, Todor Tomov wrote: > Add DT binding document for Qualcomm Camera subsystem driver. > > CC: Rob Herring <robh+dt@kernel.org> > CC: devicetree@vger.kernel.org > Signed-off-by: Todor Tomov <todor.tomov@linaro.org> > --- > .../devicetree/bindings/media/qcom,camss.txt | 191 +++++++++++++++++++++ > 1 file changed, 191 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/qcom,camss.txt Acked-by: Rob Herring <robh@kernel.org> -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Sakari, Thank you for the review. On 20.07.2017 13:13, Sakari Ailus wrote: > Hi Todor, > > On Mon, Jul 17, 2017 at 01:33:30PM +0300, Todor Tomov wrote: >> Add DT binding document for Qualcomm Camera subsystem driver. >> >> CC: Rob Herring <robh+dt@kernel.org> >> CC: devicetree@vger.kernel.org >> Signed-off-by: Todor Tomov <todor.tomov@linaro.org> >> --- >> .../devicetree/bindings/media/qcom,camss.txt | 191 +++++++++++++++++++++ >> 1 file changed, 191 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/media/qcom,camss.txt >> >> diff --git a/Documentation/devicetree/bindings/media/qcom,camss.txt b/Documentation/devicetree/bindings/media/qcom,camss.txt >> new file mode 100644 >> index 0000000..f698498 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/media/qcom,camss.txt >> @@ -0,0 +1,191 @@ >> +Qualcomm Camera Subsystem >> + >> +* Properties >> + >> +- compatible: >> + Usage: required >> + Value type: <stringlist> >> + Definition: Should contain: >> + - "qcom,msm8916-camss" >> +- reg: >> + Usage: required >> + Value type: <prop-encoded-array> >> + Definition: Register ranges as listed in the reg-names property. >> +- reg-names: >> + Usage: required >> + Value type: <stringlist> >> + Definition: Should contain the following entries: >> + - "csiphy0" >> + - "csiphy0_clk_mux" >> + - "csiphy1" >> + - "csiphy1_clk_mux" >> + - "csid0" >> + - "csid1" >> + - "ispif" >> + - "csi_clk_mux" >> + - "vfe0" >> +- interrupts: >> + Usage: required >> + Value type: <prop-encoded-array> >> + Definition: Interrupts as listed in the interrupt-names property. >> +- interrupt-names: >> + Usage: required >> + Value type: <stringlist> >> + Definition: Should contain the following entries: >> + - "csiphy0" >> + - "csiphy1" >> + - "csid0" >> + - "csid1" >> + - "ispif" >> + - "vfe0" >> +- power-domains: >> + Usage: required >> + Value type: <prop-encoded-array> >> + Definition: A phandle and power domain specifier pairs to the >> + power domain which is responsible for collapsing >> + and restoring power to the peripheral. >> +- clocks: >> + Usage: required >> + Value type: <prop-encoded-array> >> + Definition: A list of phandle and clock specifier pairs as listed >> + in clock-names property. >> +- clock-names: >> + Usage: required >> + Value type: <stringlist> >> + Definition: Should contain the following entries: >> + - "camss_top_ahb" >> + - "ispif_ahb" >> + - "csiphy0_timer" >> + - "csiphy1_timer" >> + - "csi0_ahb" >> + - "csi0" >> + - "csi0_phy" >> + - "csi0_pix" >> + - "csi0_rdi" >> + - "csi1_ahb" >> + - "csi1" >> + - "csi1_phy" >> + - "csi1_pix" >> + - "csi1_rdi" >> + - "camss_ahb" >> + - "camss_vfe_vfe" >> + - "camss_csi_vfe" >> + - "iface" >> + - "bus" >> +- vdda-supply: >> + Usage: required >> + Value type: <phandle> >> + Definition: A phandle to voltage supply for CSI2. >> +- iommus: >> + Usage: required >> + Value type: <prop-encoded-array> >> + Definition: A list of phandle and IOMMU specifier pairs. >> + >> +* Nodes >> + >> +- ports: >> + Usage: required >> + Definition: As described in video-interfaces.txt in same directory. >> + Properties: >> + - reg: >> + Usage: required >> + Value type: <u32> >> + Definition: Selects CSI2 PHY interface - PHY0 or PHY1. >> + Endpoint node properties: >> + - clock-lanes: >> + Usage: required >> + Value type: <u32> >> + Definition: The clock lane. >> + - data-lanes: >> + Usage: required >> + Value type: <prop-encoded-array> >> + Definition: An array of data lanes. >> + >> +* An Example >> + >> + camss: camss@1b00000 { >> + compatible = "qcom,msm8916-camss"; >> + reg = <0x1b0ac00 0x200>, >> + <0x1b00030 0x4>, >> + <0x1b0b000 0x200>, >> + <0x1b00038 0x4>, >> + <0x1b08000 0x100>, >> + <0x1b08400 0x100>, >> + <0x1b0a000 0x500>, >> + <0x1b00020 0x10>, >> + <0x1b10000 0x1000>; >> + reg-names = "csiphy0", >> + "csiphy0_clk_mux", >> + "csiphy1", >> + "csiphy1_clk_mux", >> + "csid0", >> + "csid1", >> + "ispif", >> + "csi_clk_mux", >> + "vfe0"; >> + interrupts = <GIC_SPI 78 0>, >> + <GIC_SPI 79 0>, >> + <GIC_SPI 51 0>, >> + <GIC_SPI 52 0>, >> + <GIC_SPI 55 0>, >> + <GIC_SPI 57 0>; >> + interrupt-names = "csiphy0", >> + "csiphy1", >> + "csid0", >> + "csid1", >> + "ispif", >> + "vfe0"; >> + power-domains = <&gcc VFE_GDSC>; >> + clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>, >> + <&gcc GCC_CAMSS_ISPIF_AHB_CLK>, >> + <&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>, >> + <&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>, >> + <&gcc GCC_CAMSS_CSI0_AHB_CLK>, >> + <&gcc GCC_CAMSS_CSI0_CLK>, >> + <&gcc GCC_CAMSS_CSI0PHY_CLK>, >> + <&gcc GCC_CAMSS_CSI0PIX_CLK>, >> + <&gcc GCC_CAMSS_CSI0RDI_CLK>, >> + <&gcc GCC_CAMSS_CSI1_AHB_CLK>, >> + <&gcc GCC_CAMSS_CSI1_CLK>, >> + <&gcc GCC_CAMSS_CSI1PHY_CLK>, >> + <&gcc GCC_CAMSS_CSI1PIX_CLK>, >> + <&gcc GCC_CAMSS_CSI1RDI_CLK>, >> + <&gcc GCC_CAMSS_AHB_CLK>, >> + <&gcc GCC_CAMSS_VFE0_CLK>, >> + <&gcc GCC_CAMSS_CSI_VFE0_CLK>, >> + <&gcc GCC_CAMSS_VFE_AHB_CLK>, >> + <&gcc GCC_CAMSS_VFE_AXI_CLK>; >> + clock-names = "camss_top_ahb", >> + "ispif_ahb", >> + "csiphy0_timer", >> + "csiphy1_timer", >> + "csi0_ahb", >> + "csi0", >> + "csi0_phy", >> + "csi0_pix", >> + "csi0_rdi", >> + "csi1_ahb", >> + "csi1", >> + "csi1_phy", >> + "csi1_pix", >> + "csi1_rdi", >> + "camss_ahb", >> + "camss_vfe_vfe", >> + "camss_csi_vfe", >> + "iface", >> + "bus"; >> + vdda-supply = <&pm8916_l2>; >> + iommus = <&apps_iommu 3>; >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + port@0 { >> + reg = <0>; >> + csiphy0_ep: endpoint { >> + clock-lanes = <1>; >> + data-lanes = <0 2>; > > Do you support lane mapping? The values suggest "yes". That's something I > could improve in the documentation: if lane mapping isn't supported, then > the clock lane should be 0 and the data lanes from 1 to n. Lane mapping is supported only for the data lanes. The clock lane is always the physical lane 1. This is why I think it makes sense to keep the value of the clock lane to 1 as this is the physical lane 1 really. I'll add explanation in the documentation for this and for the data lanes too so it is clear. > > Is the split of the lanes between the ports static and specific to the > hardware? Each port describes a separate CSIPHY so each has its own set of lanes. > >> + remote-endpoint = <&ov5645_ep>; >> + }; >> + }; >> + }; >> + }; >
Hi Todor, On Fri, Aug 04, 2017 at 02:54:21PM +0300, Todor Tomov wrote: > Hi Sakari, > > Thank you for the review. You're welcome! > > On 20.07.2017 13:13, Sakari Ailus wrote: > > Hi Todor, > > > > On Mon, Jul 17, 2017 at 01:33:30PM +0300, Todor Tomov wrote: > >> Add DT binding document for Qualcomm Camera subsystem driver. > >> > >> CC: Rob Herring <robh+dt@kernel.org> > >> CC: devicetree@vger.kernel.org > >> Signed-off-by: Todor Tomov <todor.tomov@linaro.org> > >> --- > >> .../devicetree/bindings/media/qcom,camss.txt | 191 +++++++++++++++++++++ > >> 1 file changed, 191 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/media/qcom,camss.txt > >> > >> diff --git a/Documentation/devicetree/bindings/media/qcom,camss.txt b/Documentation/devicetree/bindings/media/qcom,camss.txt > >> new file mode 100644 > >> index 0000000..f698498 > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/media/qcom,camss.txt > >> @@ -0,0 +1,191 @@ > >> +Qualcomm Camera Subsystem > >> + > >> +* Properties > >> + > >> +- compatible: > >> + Usage: required > >> + Value type: <stringlist> > >> + Definition: Should contain: > >> + - "qcom,msm8916-camss" > >> +- reg: > >> + Usage: required > >> + Value type: <prop-encoded-array> > >> + Definition: Register ranges as listed in the reg-names property. > >> +- reg-names: > >> + Usage: required > >> + Value type: <stringlist> > >> + Definition: Should contain the following entries: > >> + - "csiphy0" > >> + - "csiphy0_clk_mux" > >> + - "csiphy1" > >> + - "csiphy1_clk_mux" > >> + - "csid0" > >> + - "csid1" > >> + - "ispif" > >> + - "csi_clk_mux" > >> + - "vfe0" > >> +- interrupts: > >> + Usage: required > >> + Value type: <prop-encoded-array> > >> + Definition: Interrupts as listed in the interrupt-names property. > >> +- interrupt-names: > >> + Usage: required > >> + Value type: <stringlist> > >> + Definition: Should contain the following entries: > >> + - "csiphy0" > >> + - "csiphy1" > >> + - "csid0" > >> + - "csid1" > >> + - "ispif" > >> + - "vfe0" > >> +- power-domains: > >> + Usage: required > >> + Value type: <prop-encoded-array> > >> + Definition: A phandle and power domain specifier pairs to the > >> + power domain which is responsible for collapsing > >> + and restoring power to the peripheral. > >> +- clocks: > >> + Usage: required > >> + Value type: <prop-encoded-array> > >> + Definition: A list of phandle and clock specifier pairs as listed > >> + in clock-names property. > >> +- clock-names: > >> + Usage: required > >> + Value type: <stringlist> > >> + Definition: Should contain the following entries: > >> + - "camss_top_ahb" > >> + - "ispif_ahb" > >> + - "csiphy0_timer" > >> + - "csiphy1_timer" > >> + - "csi0_ahb" > >> + - "csi0" > >> + - "csi0_phy" > >> + - "csi0_pix" > >> + - "csi0_rdi" > >> + - "csi1_ahb" > >> + - "csi1" > >> + - "csi1_phy" > >> + - "csi1_pix" > >> + - "csi1_rdi" > >> + - "camss_ahb" > >> + - "camss_vfe_vfe" > >> + - "camss_csi_vfe" > >> + - "iface" > >> + - "bus" > >> +- vdda-supply: > >> + Usage: required > >> + Value type: <phandle> > >> + Definition: A phandle to voltage supply for CSI2. > >> +- iommus: > >> + Usage: required > >> + Value type: <prop-encoded-array> > >> + Definition: A list of phandle and IOMMU specifier pairs. > >> + > >> +* Nodes > >> + > >> +- ports: > >> + Usage: required > >> + Definition: As described in video-interfaces.txt in same directory. > >> + Properties: > >> + - reg: > >> + Usage: required > >> + Value type: <u32> > >> + Definition: Selects CSI2 PHY interface - PHY0 or PHY1. > >> + Endpoint node properties: > >> + - clock-lanes: > >> + Usage: required > >> + Value type: <u32> > >> + Definition: The clock lane. > >> + - data-lanes: > >> + Usage: required > >> + Value type: <prop-encoded-array> > >> + Definition: An array of data lanes. > >> + > >> +* An Example > >> + > >> + camss: camss@1b00000 { > >> + compatible = "qcom,msm8916-camss"; > >> + reg = <0x1b0ac00 0x200>, > >> + <0x1b00030 0x4>, > >> + <0x1b0b000 0x200>, > >> + <0x1b00038 0x4>, > >> + <0x1b08000 0x100>, > >> + <0x1b08400 0x100>, > >> + <0x1b0a000 0x500>, > >> + <0x1b00020 0x10>, > >> + <0x1b10000 0x1000>; > >> + reg-names = "csiphy0", > >> + "csiphy0_clk_mux", > >> + "csiphy1", > >> + "csiphy1_clk_mux", > >> + "csid0", > >> + "csid1", > >> + "ispif", > >> + "csi_clk_mux", > >> + "vfe0"; > >> + interrupts = <GIC_SPI 78 0>, > >> + <GIC_SPI 79 0>, > >> + <GIC_SPI 51 0>, > >> + <GIC_SPI 52 0>, > >> + <GIC_SPI 55 0>, > >> + <GIC_SPI 57 0>; > >> + interrupt-names = "csiphy0", > >> + "csiphy1", > >> + "csid0", > >> + "csid1", > >> + "ispif", > >> + "vfe0"; > >> + power-domains = <&gcc VFE_GDSC>; > >> + clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>, > >> + <&gcc GCC_CAMSS_ISPIF_AHB_CLK>, > >> + <&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>, > >> + <&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>, > >> + <&gcc GCC_CAMSS_CSI0_AHB_CLK>, > >> + <&gcc GCC_CAMSS_CSI0_CLK>, > >> + <&gcc GCC_CAMSS_CSI0PHY_CLK>, > >> + <&gcc GCC_CAMSS_CSI0PIX_CLK>, > >> + <&gcc GCC_CAMSS_CSI0RDI_CLK>, > >> + <&gcc GCC_CAMSS_CSI1_AHB_CLK>, > >> + <&gcc GCC_CAMSS_CSI1_CLK>, > >> + <&gcc GCC_CAMSS_CSI1PHY_CLK>, > >> + <&gcc GCC_CAMSS_CSI1PIX_CLK>, > >> + <&gcc GCC_CAMSS_CSI1RDI_CLK>, > >> + <&gcc GCC_CAMSS_AHB_CLK>, > >> + <&gcc GCC_CAMSS_VFE0_CLK>, > >> + <&gcc GCC_CAMSS_CSI_VFE0_CLK>, > >> + <&gcc GCC_CAMSS_VFE_AHB_CLK>, > >> + <&gcc GCC_CAMSS_VFE_AXI_CLK>; > >> + clock-names = "camss_top_ahb", > >> + "ispif_ahb", > >> + "csiphy0_timer", > >> + "csiphy1_timer", > >> + "csi0_ahb", > >> + "csi0", > >> + "csi0_phy", > >> + "csi0_pix", > >> + "csi0_rdi", > >> + "csi1_ahb", > >> + "csi1", > >> + "csi1_phy", > >> + "csi1_pix", > >> + "csi1_rdi", > >> + "camss_ahb", > >> + "camss_vfe_vfe", > >> + "camss_csi_vfe", > >> + "iface", > >> + "bus"; > >> + vdda-supply = <&pm8916_l2>; > >> + iommus = <&apps_iommu 3>; > >> + ports { > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + port@0 { > >> + reg = <0>; > >> + csiphy0_ep: endpoint { > >> + clock-lanes = <1>; > >> + data-lanes = <0 2>; > > > > Do you support lane mapping? The values suggest "yes". That's something I > > could improve in the documentation: if lane mapping isn't supported, then > > the clock lane should be 0 and the data lanes from 1 to n. > > Lane mapping is supported only for the data lanes. The clock lane is always > the physical lane 1. This is why I think it makes sense to keep the value > of the clock lane to 1 as this is the physical lane 1 really. I'll add > explanation in the documentation for this and for the data lanes too so > it is clear. Could you document this in the binding documentation? What I've seen previously is that either the lanes can be mapped any way you want, or there's just a single possible mapping. > > > > > Is the split of the lanes between the ports static and specific to the > > hardware? > > Each port describes a separate CSIPHY so each has its own set of lanes. Ack. I asked since if the lanes can be shared, the lane numbering needs to be global to the device; otherwise there's no way to convey the lane/PHY association using the standard bindings.
diff --git a/Documentation/devicetree/bindings/media/qcom,camss.txt b/Documentation/devicetree/bindings/media/qcom,camss.txt new file mode 100644 index 0000000..f698498 --- /dev/null +++ b/Documentation/devicetree/bindings/media/qcom,camss.txt @@ -0,0 +1,191 @@ +Qualcomm Camera Subsystem + +* Properties + +- compatible: + Usage: required + Value type: <stringlist> + Definition: Should contain: + - "qcom,msm8916-camss" +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register ranges as listed in the reg-names property. +- reg-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the following entries: + - "csiphy0" + - "csiphy0_clk_mux" + - "csiphy1" + - "csiphy1_clk_mux" + - "csid0" + - "csid1" + - "ispif" + - "csi_clk_mux" + - "vfe0" +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Interrupts as listed in the interrupt-names property. +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the following entries: + - "csiphy0" + - "csiphy1" + - "csid0" + - "csid1" + - "ispif" + - "vfe0" +- power-domains: + Usage: required + Value type: <prop-encoded-array> + Definition: A phandle and power domain specifier pairs to the + power domain which is responsible for collapsing + and restoring power to the peripheral. +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and clock specifier pairs as listed + in clock-names property. +- clock-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the following entries: + - "camss_top_ahb" + - "ispif_ahb" + - "csiphy0_timer" + - "csiphy1_timer" + - "csi0_ahb" + - "csi0" + - "csi0_phy" + - "csi0_pix" + - "csi0_rdi" + - "csi1_ahb" + - "csi1" + - "csi1_phy" + - "csi1_pix" + - "csi1_rdi" + - "camss_ahb" + - "camss_vfe_vfe" + - "camss_csi_vfe" + - "iface" + - "bus" +- vdda-supply: + Usage: required + Value type: <phandle> + Definition: A phandle to voltage supply for CSI2. +- iommus: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. + +* Nodes + +- ports: + Usage: required + Definition: As described in video-interfaces.txt in same directory. + Properties: + - reg: + Usage: required + Value type: <u32> + Definition: Selects CSI2 PHY interface - PHY0 or PHY1. + Endpoint node properties: + - clock-lanes: + Usage: required + Value type: <u32> + Definition: The clock lane. + - data-lanes: + Usage: required + Value type: <prop-encoded-array> + Definition: An array of data lanes. + +* An Example + + camss: camss@1b00000 { + compatible = "qcom,msm8916-camss"; + reg = <0x1b0ac00 0x200>, + <0x1b00030 0x4>, + <0x1b0b000 0x200>, + <0x1b00038 0x4>, + <0x1b08000 0x100>, + <0x1b08400 0x100>, + <0x1b0a000 0x500>, + <0x1b00020 0x10>, + <0x1b10000 0x1000>; + reg-names = "csiphy0", + "csiphy0_clk_mux", + "csiphy1", + "csiphy1_clk_mux", + "csid0", + "csid1", + "ispif", + "csi_clk_mux", + "vfe0"; + interrupts = <GIC_SPI 78 0>, + <GIC_SPI 79 0>, + <GIC_SPI 51 0>, + <GIC_SPI 52 0>, + <GIC_SPI 55 0>, + <GIC_SPI 57 0>; + interrupt-names = "csiphy0", + "csiphy1", + "csid0", + "csid1", + "ispif", + "vfe0"; + power-domains = <&gcc VFE_GDSC>; + clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>, + <&gcc GCC_CAMSS_ISPIF_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>, + <&gcc GCC_CAMSS_CSI0_AHB_CLK>, + <&gcc GCC_CAMSS_CSI0_CLK>, + <&gcc GCC_CAMSS_CSI0PHY_CLK>, + <&gcc GCC_CAMSS_CSI0PIX_CLK>, + <&gcc GCC_CAMSS_CSI0RDI_CLK>, + <&gcc GCC_CAMSS_CSI1_AHB_CLK>, + <&gcc GCC_CAMSS_CSI1_CLK>, + <&gcc GCC_CAMSS_CSI1PHY_CLK>, + <&gcc GCC_CAMSS_CSI1PIX_CLK>, + <&gcc GCC_CAMSS_CSI1RDI_CLK>, + <&gcc GCC_CAMSS_AHB_CLK>, + <&gcc GCC_CAMSS_VFE0_CLK>, + <&gcc GCC_CAMSS_CSI_VFE0_CLK>, + <&gcc GCC_CAMSS_VFE_AHB_CLK>, + <&gcc GCC_CAMSS_VFE_AXI_CLK>; + clock-names = "camss_top_ahb", + "ispif_ahb", + "csiphy0_timer", + "csiphy1_timer", + "csi0_ahb", + "csi0", + "csi0_phy", + "csi0_pix", + "csi0_rdi", + "csi1_ahb", + "csi1", + "csi1_phy", + "csi1_pix", + "csi1_rdi", + "camss_ahb", + "camss_vfe_vfe", + "camss_csi_vfe", + "iface", + "bus"; + vdda-supply = <&pm8916_l2>; + iommus = <&apps_iommu 3>; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + csiphy0_ep: endpoint { + clock-lanes = <1>; + data-lanes = <0 2>; + remote-endpoint = <&ov5645_ep>; + }; + }; + }; + };
Add DT binding document for Qualcomm Camera subsystem driver. CC: Rob Herring <robh+dt@kernel.org> CC: devicetree@vger.kernel.org Signed-off-by: Todor Tomov <todor.tomov@linaro.org> --- .../devicetree/bindings/media/qcom,camss.txt | 191 +++++++++++++++++++++ 1 file changed, 191 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/qcom,camss.txt