[v3,3/5] ASoC: codecs: msm8916-wcd-analog: add MBHC support

Message ID	20170809164927.19663-4-srinivas.kandagatla@linaro.org (mailing list archive)
State	New, archived
Headers	show Return-Path: <alsa-devel-bounces@alsa-project.org> From: srinivas.kandagatla@linaro.org To: Mark Brown <broonie@kernel.org>, Banajit Goswami <bgoswami@codeaurora.org>, alsa-devel@alsa-project.org Date: Wed, 9 Aug 2017 18:49:25 +0200 Message-Id: <20170809164927.19663-4-srinivas.kandagatla@linaro.org> In-Reply-To: <20170809164927.19663-1-srinivas.kandagatla@linaro.org> References: <20170809164927.19663-1-srinivas.kandagatla@linaro.org> Cc: damien.riegel@savoirfairelinux.com, Patrick Lai <plai@codeaurora.org>, linux-kernel@vger.kernel.org, Takashi Iwai <tiwai@suse.com>, Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Subject: [alsa-devel] [PATCH v3 3/5] ASoC: codecs: msm8916-wcd-analog: add MBHC support Precedence: list MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Errors-To: alsa-devel-bounces@alsa-project.org Sender: alsa-devel-bounces@alsa-project.org

diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt index 05b67a1..551ecab 100644 --- a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt +++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt @@ -31,9 +31,22 @@ Required properties - vdd-cdc-io-supply: phandle to VDD_CDC_IO regulator DT node. - vdd-cdc-tx-rx-cx-supply: phandle to VDD_CDC_TX/RX/CX regulator DT node. - vdd-micbias-supply: phandle of VDD_MICBIAS supply's regulator DT node. - Optional Properties: + - qcom,mbhc-vthreshold-low: Array of 5 threshold voltages in mV for 5 buttons + detection on headset when the mbhc is powered up + by internal current source, this is a low power. + - qcom,mbhc-vthreshold-high: Array of 5 thresold voltages in mV for 5 buttons + detection on headset when mbhc is powered up + from micbias. - qcom,micbias-lvl: Voltage (mV) for Mic Bias +- qcom,hphl-jack-type-normally-open: boolean, present if hphl pin on jack is a + NO (Normally Open). If not specified, then + its assumed that hphl pin on jack is NC + (Normally Closed). +- qcom,gnd-jack-type-normally-open: boolean, present if gnd pin on jack is + NO (Normally Open). If not specified, then + its assumed that gnd pin on jack is NC + (Normally Closed). - qcom,micbias1-ext-cap: boolean, present if micbias1 has external capacitor connected. - qcom,micbias2-ext-cap: boolean, present if micbias2 has external capacitor @@ -49,6 +62,8 @@ spmi_bus { reg-names = "pmic-codec-core"; clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>; clock-names = "mclk"; + qcom,mbhc-vthreshold-low = <75 150 237 450 500>; + qcom,mbhc-vthreshold-high = <75 150 237 450 500>; interrupt-parent = <&spmi_bus>; interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>, <0x1 0xf0 0x1 IRQ_TYPE_NONE>, diff --git a/sound/soc/codecs/msm8916-wcd-analog.c b/sound/soc/codecs/msm8916-wcd-analog.c index dec4978..b84aeb4 100644 --- a/sound/soc/codecs/msm8916-wcd-analog.c +++ b/sound/soc/codecs/msm8916-wcd-analog.c @@ -12,9 +12,16 @@ #include <sound/pcm.h> #include <sound/pcm_params.h> #include <sound/tlv.h> +#include <sound/jack.h> #define CDC_D_REVISION1 (0xf000) #define CDC_D_PERPH_SUBTYPE (0xf005) +#define CDC_D_INT_EN_SET (0x015) +#define CDC_D_INT_EN_CLR (0x016) +#define MBHC_SWITCH_INT BIT(7) +#define MBHC_MIC_ELECTRICAL_INS_REM_DET BIT(6) +#define MBHC_BUTTON_PRESS_DET BIT(5) +#define MBHC_BUTTON_RELEASE_DET BIT(4) #define CDC_D_CDC_RST_CTL (0xf046) #define RST_CTL_DIG_SW_RST_N_MASK BIT(7) #define RST_CTL_DIG_SW_RST_N_RESET 0 @@ -37,6 +44,8 @@ #define DIG_CLK_CTL_RXD1_CLK_EN BIT(0) #define DIG_CLK_CTL_RXD2_CLK_EN BIT(1) #define DIG_CLK_CTL_RXD3_CLK_EN BIT(2) +#define DIG_CLK_CTL_D_MBHC_CLK_EN_MASK BIT(3) +#define DIG_CLK_CTL_D_MBHC_CLK_EN BIT(3) #define DIG_CLK_CTL_TXD_CLK_EN BIT(4) #define DIG_CLK_CTL_NCP_CLK_EN_MASK BIT(6) #define DIG_CLK_CTL_NCP_CLK_EN BIT(6) @@ -132,8 +141,51 @@ #define MICB_1_INT_TX3_INT_PULLUP_EN_TX1N_TO_GND 0 #define CDC_A_MICB_2_EN (0xf144) +#define CDC_A_MICB_2_EN_ENABLE BIT(7) +#define CDC_A_MICB_2_PULL_DOWN_EN_MASK BIT(5) +#define CDC_A_MICB_2_PULL_DOWN_EN BIT(5) #define CDC_A_TX_1_2_ATEST_CTL_2 (0xf145) #define CDC_A_MASTER_BIAS_CTL (0xf146) +#define CDC_A_MBHC_DET_CTL_1 (0xf147) +#define CDC_A_MBHC_DET_CTL_L_DET_EN BIT(7) +#define CDC_A_MBHC_DET_CTL_GND_DET_EN BIT(6) +#define CDC_A_MBHC_DET_CTL_MECH_DET_TYPE_INSERTION BIT(5) +#define CDC_A_MBHC_DET_CTL_MECH_DET_TYPE_REMOVAL (0) +#define CDC_A_MBHC_DET_CTL_MECH_DET_TYPE_MASK BIT(5) +#define CDC_A_MBHC_DET_CTL_MECH_DET_TYPE_SHIFT (5) +#define CDC_A_MBHC_DET_CTL_MIC_CLAMP_CTL_AUTO BIT(4) +#define CDC_A_MBHC_DET_CTL_MIC_CLAMP_CTL_MANUAL BIT(3) +#define CDC_A_MBHC_DET_CTL_MIC_CLAMP_CTL_MASK GENMASK(4, 3) +#define CDC_A_MBHC_DET_CTL_MBHC_BIAS_EN BIT(2) +#define CDC_A_MBHC_DET_CTL_2 (0xf150) +#define CDC_A_MBHC_DET_CTL_HS_L_DET_PULL_UP_CTRL_I_3P0 (BIT(7) | BIT(6)) +#define CDC_A_MBHC_DET_CTL_HS_L_DET_COMPA_CTRL_V0P9_VDD BIT(5) +#define CDC_A_PLUG_TYPE_MASK GENMASK(4, 3) +#define CDC_A_HPHL_PLUG_TYPE_NO BIT(4) +#define CDC_A_GND_PLUG_TYPE_NO BIT(3) +#define CDC_A_MBHC_DET_CTL_HPHL_100K_TO_GND_EN_MASK BIT(0) +#define CDC_A_MBHC_DET_CTL_HPHL_100K_TO_GND_EN BIT(0) +#define CDC_A_MBHC_FSM_CTL (0xf151) +#define CDC_A_MBHC_FSM_CTL_MBHC_FSM_EN BIT(7) +#define CDC_A_MBHC_FSM_CTL_MBHC_FSM_EN_MASK BIT(7) +#define CDC_A_MBHC_FSM_CTL_BTN_ISRC_CTRL_I_100UA (0x3 << 4) +#define CDC_A_MBHC_FSM_CTL_BTN_ISRC_CTRL_MASK GENMASK(6, 4) +#define CDC_A_MBHC_DBNC_TIMER (0xf152) +#define CDC_A_MBHC_DBNC_TIMER_BTN_DBNC_T_16MS BIT(3) +#define CDC_A_MBHC_DBNC_TIMER_INSREM_DBNC_T_256_MS (0x9 << 4) +#define CDC_A_MBHC_BTN0_ZDET_CTL_0 (0xf153) +#define CDC_A_MBHC_BTN1_ZDET_CTL_1 (0xf154) +#define CDC_A_MBHC_BTN2_ZDET_CTL_2 (0xf155) +#define CDC_A_MBHC_BTN3_CTL (0xf156) +#define CDC_A_MBHC_BTN4_CTL (0xf157) +#define CDC_A_MBHC_BTN_VREF_FINE_SHIFT (2) +#define CDC_A_MBHC_BTN_VREF_FINE_MASK GENMASK(4, 2) +#define CDC_A_MBHC_BTN_VREF_COARSE_MASK GENMASK(7, 5) +#define CDC_A_MBHC_BTN_VREF_COARSE_SHIFT (5) +#define CDC_A_MBHC_BTN_VREF_MASK (CDC_A_MBHC_BTN_VREF_COARSE_MASK | \ + CDC_A_MBHC_BTN_VREF_FINE_MASK) +#define CDC_A_MBHC_RESULT_1 (0xf158) +#define CDC_A_MBHC_RESULT_1_BTN_RESULT_MASK GENMASK(4, 0) #define CDC_A_TX_1_EN (0xf160) #define CDC_A_TX_2_EN (0xf161) #define CDC_A_TX_1_2_TEST_CTL_1 (0xf162) @@ -217,16 +269,34 @@ #define MSM8916_WCD_ANALOG_FORMATS (SNDRV_PCM_FMTBIT_S16_LE |\ SNDRV_PCM_FMTBIT_S24_LE) +static int btn_mask = SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3 | SND_JACK_BTN_4; +static int hs_jack_mask = SND_JACK_HEADPHONE | SND_JACK_HEADSET; + static const char * const supply_names[] = { "vdd-cdc-io", "vdd-cdc-tx-rx-cx", }; +#define MBHC_MAX_BUTTONS (5) + struct pm8916_wcd_analog_priv { u16 pmic_rev; u16 codec_version; + bool mbhc_btn_enabled; + /* special event to detect accessory type */ + bool mbhc_btn0_pressed; + bool detect_accessory_type; struct clk *mclk; + struct snd_soc_codec *codec; struct regulator_bulk_data supplies[ARRAY_SIZE(supply_names)]; + struct snd_soc_jack *jack; + bool hphl_jack_type_normally_open; + bool gnd_jack_type_normally_open; + /* Voltage threshold when internal current source of 100uA is used */ + u32 vref_btn_cs[MBHC_MAX_BUTTONS]; + /* Voltage threshold when microphone bias is ON */ + u32 vref_btn_micb[MBHC_MAX_BUTTONS]; unsigned int micbias1_cap_mode; unsigned int micbias2_cap_mode; unsigned int micbias_mv; @@ -366,6 +436,97 @@ static int pm8916_wcd_analog_enable_micbias_int1(struct wcd->micbias1_cap_mode); } +static void pm8916_wcd_setup_mbhc(struct pm8916_wcd_analog_priv *wcd) +{ + struct snd_soc_codec *codec = wcd->codec; + u32 plug_type = 0; + u32 int_en_mask; + + snd_soc_write(codec, CDC_A_MBHC_DET_CTL_1, + CDC_A_MBHC_DET_CTL_L_DET_EN | + CDC_A_MBHC_DET_CTL_MECH_DET_TYPE_INSERTION | + CDC_A_MBHC_DET_CTL_MIC_CLAMP_CTL_AUTO | + CDC_A_MBHC_DET_CTL_MBHC_BIAS_EN); + + if (wcd->hphl_jack_type_normally_open) + plug_type |= CDC_A_HPHL_PLUG_TYPE_NO; + + if (wcd->gnd_jack_type_normally_open) + plug_type |= CDC_A_GND_PLUG_TYPE_NO; + + snd_soc_write(codec, CDC_A_MBHC_DET_CTL_2, + CDC_A_MBHC_DET_CTL_HS_L_DET_PULL_UP_CTRL_I_3P0 | + CDC_A_MBHC_DET_CTL_HS_L_DET_COMPA_CTRL_V0P9_VDD | + plug_type | + CDC_A_MBHC_DET_CTL_HPHL_100K_TO_GND_EN); + + + snd_soc_write(codec, CDC_A_MBHC_DBNC_TIMER, + CDC_A_MBHC_DBNC_TIMER_INSREM_DBNC_T_256_MS | + CDC_A_MBHC_DBNC_TIMER_BTN_DBNC_T_16MS); + + /* enable MBHC clock */ + snd_soc_update_bits(codec, CDC_D_CDC_DIG_CLK_CTL, + DIG_CLK_CTL_D_MBHC_CLK_EN_MASK, + DIG_CLK_CTL_D_MBHC_CLK_EN); + + int_en_mask = MBHC_SWITCH_INT; + if (wcd->mbhc_btn_enabled) + int_en_mask |= MBHC_BUTTON_PRESS_DET | MBHC_BUTTON_RELEASE_DET; + + snd_soc_update_bits(codec, CDC_D_INT_EN_CLR, int_en_mask, 0); + snd_soc_update_bits(codec, CDC_D_INT_EN_SET, int_en_mask, int_en_mask); + wcd->mbhc_btn0_pressed = false; + wcd->detect_accessory_type = true; +} + +static int pm8916_mbhc_configure_bias(struct pm8916_wcd_analog_priv *priv, + bool micbias2_enabled) +{ + struct snd_soc_codec *codec = priv->codec; + u32 coarse, fine, reg_val, reg_addr; + int *vrefs, i; + + if (!micbias2_enabled) { /* use internal 100uA Current source */ + /* Enable internal 2.2k Internal Rbias Resistor */ + snd_soc_update_bits(codec, CDC_A_MICB_1_INT_RBIAS, + MICB_1_INT_TX2_INT_RBIAS_EN_MASK, + MICB_1_INT_TX2_INT_RBIAS_EN_ENABLE); + /* Remove pull down on MIC BIAS2 */ + snd_soc_update_bits(codec, CDC_A_MICB_2_EN, + CDC_A_MICB_2_PULL_DOWN_EN_MASK, + 0); + /* enable 100uA internal current source */ + snd_soc_update_bits(codec, CDC_A_MBHC_FSM_CTL, + CDC_A_MBHC_FSM_CTL_BTN_ISRC_CTRL_MASK, + CDC_A_MBHC_FSM_CTL_BTN_ISRC_CTRL_I_100UA); + } + snd_soc_update_bits(codec, CDC_A_MBHC_FSM_CTL, + CDC_A_MBHC_FSM_CTL_MBHC_FSM_EN_MASK, + CDC_A_MBHC_FSM_CTL_MBHC_FSM_EN); + + if (micbias2_enabled) + vrefs = &priv->vref_btn_micb[0]; + else + vrefs = &priv->vref_btn_cs[0]; + + /* program vref ranges for all the buttons */ + reg_addr = CDC_A_MBHC_BTN0_ZDET_CTL_0; + for (i = 0; i < MBHC_MAX_BUTTONS; i++) { + /* split mv in to coarse parts of 100mv & fine parts of 12mv */ + coarse = (vrefs[i] / 100); + fine = ((vrefs[i] % 100) / 12); + reg_val = (coarse << CDC_A_MBHC_BTN_VREF_COARSE_SHIFT) | + (fine << CDC_A_MBHC_BTN_VREF_FINE_SHIFT); + snd_soc_update_bits(codec, reg_addr, + CDC_A_MBHC_BTN_VREF_MASK, + reg_val); + reg_addr++; + } + + return 0; +} + static int pm8916_wcd_analog_enable_micbias_int2(struct snd_soc_dapm_widget *w, struct snd_kcontrol @@ -374,6 +535,15 @@ static int pm8916_wcd_analog_enable_micbias_int2(struct struct snd_soc_codec *codec = snd_soc_dapm_to_codec(w->dapm); struct pm8916_wcd_analog_priv *wcd = snd_soc_codec_get_drvdata(codec); + switch (event) { + case SND_SOC_DAPM_POST_PMU: + pm8916_mbhc_configure_bias(wcd, true); + break; + case SND_SOC_DAPM_POST_PMD: + pm8916_mbhc_configure_bias(wcd, false); + break; + } + return pm8916_wcd_analog_enable_micbias_int(codec, event, w->reg, wcd->micbias2_cap_mode); } @@ -541,9 +711,14 @@ static int pm8916_wcd_analog_probe(struct snd_soc_codec *codec) snd_soc_write(codec, wcd_reg_defaults_2_0[reg].reg, wcd_reg_defaults_2_0[reg].def); + priv->codec = codec; + snd_soc_update_bits(codec, CDC_D_CDC_RST_CTL, RST_CTL_DIG_SW_RST_N_MASK, RST_CTL_DIG_SW_RST_N_REMOVE_RESET); + + pm8916_wcd_setup_mbhc(priv); + return 0; } @@ -742,11 +917,130 @@ static const struct snd_soc_dapm_widget pm8916_wcd_analog_dapm_widgets[] = { SND_SOC_DAPM_SUPPLY("A_MCLK2", CDC_D_CDC_TOP_CLK_CTL, 3, 0, NULL, 0), }; +static int pm8916_wcd_analog_set_jack(struct snd_soc_codec *codec, + struct snd_soc_jack *jack, + void *data) +{ + struct pm8916_wcd_analog_priv *wcd = snd_soc_codec_get_drvdata(codec); + + wcd->jack = jack; + + return 0; +} + static struct regmap *pm8916_get_regmap(struct device *dev) { return dev_get_regmap(dev->parent, NULL); } +static irqreturn_t mbhc_btn_release_irq_handler(int irq, void *arg) +{ + struct pm8916_wcd_analog_priv *priv = arg; + + if (priv->detect_accessory_type) { + struct snd_soc_codec *codec = priv->codec; + u32 val = snd_soc_read(codec, CDC_A_MBHC_RESULT_1); + + /* check if its BTN0 thats released */ + if ((val >= 0) && !(val & CDC_A_MBHC_RESULT_1_BTN_RESULT_MASK)) + priv->mbhc_btn0_pressed = false; + + } else { + snd_soc_jack_report(priv->jack, 0, btn_mask); + } + + return IRQ_HANDLED; +} + +static irqreturn_t mbhc_btn_press_irq_handler(int irq, void *arg) +{ + struct pm8916_wcd_analog_priv *priv = arg; + struct snd_soc_codec *codec = priv->codec; + u32 btn_result; + + btn_result = snd_soc_read(codec, CDC_A_MBHC_RESULT_1) & + CDC_A_MBHC_RESULT_1_BTN_RESULT_MASK; + + switch (btn_result) { + case 0xf: + snd_soc_jack_report(priv->jack, SND_JACK_BTN_4, btn_mask); + break; + case 0x7: + snd_soc_jack_report(priv->jack, SND_JACK_BTN_3, btn_mask); + break; + case 0x3: + snd_soc_jack_report(priv->jack, SND_JACK_BTN_2, btn_mask); + break; + case 0x1: + snd_soc_jack_report(priv->jack, SND_JACK_BTN_1, btn_mask); + break; + case 0x0: + /* handle BTN_0 specially for type detection */ + if (priv->detect_accessory_type) + priv->mbhc_btn0_pressed = true; + else + snd_soc_jack_report(priv->jack, + SND_JACK_BTN_0, btn_mask); + break; + default: + dev_err(codec->dev, + "Unexpected button press result (%x)", btn_result); + break; + } + + return IRQ_HANDLED; +} + + +static irqreturn_t pm8916_mbhc_switch_irq_handler(int irq, void *arg) +{ + struct pm8916_wcd_analog_priv *priv = arg; + struct snd_soc_codec *codec = priv->codec; + bool ins = false; + + if (snd_soc_read(codec, CDC_A_MBHC_DET_CTL_1) & + CDC_A_MBHC_DET_CTL_MECH_DET_TYPE_MASK) + ins = true; + + /* Set the detection type appropriately */ + snd_soc_update_bits(codec, CDC_A_MBHC_DET_CTL_1, + CDC_A_MBHC_DET_CTL_MECH_DET_TYPE_MASK, + (!ins << CDC_A_MBHC_DET_CTL_MECH_DET_TYPE_SHIFT)); + + + if (ins) { /* hs insertion */ + bool micbias_enabled = false; + + if (snd_soc_read(codec, CDC_A_MICB_2_EN) & + CDC_A_MICB_2_EN_ENABLE) + micbias_enabled = true; + + pm8916_mbhc_configure_bias(priv, micbias_enabled); + + /* + * if only a btn0 press event is receive just before + * insert event then its a 3 pole headphone else if + * both press and release event received then its + * a headset. + */ + if (priv->mbhc_btn0_pressed) + snd_soc_jack_report(priv->jack, + SND_JACK_HEADPHONE, hs_jack_mask); + else + snd_soc_jack_report(priv->jack, + SND_JACK_HEADSET, hs_jack_mask); + + priv->detect_accessory_type = false; + + } else { /* removal */ + snd_soc_jack_report(priv->jack, 0, hs_jack_mask); + priv->detect_accessory_type = true; + priv->mbhc_btn0_pressed = false; + } + + return IRQ_HANDLED; +} + static struct snd_soc_dai_driver pm8916_wcd_analog_dai[] = { [0] = { .name = "pm8916_wcd_analog_pdm_rx", @@ -775,6 +1069,7 @@ static struct snd_soc_dai_driver pm8916_wcd_analog_dai[] = { static struct snd_soc_codec_driver pm8916_wcd_analog = { .probe = pm8916_wcd_analog_probe, .remove = pm8916_wcd_analog_remove, + .set_jack = pm8916_wcd_analog_set_jack, .get_regmap = pm8916_get_regmap, .component_driver = { .controls = pm8916_wcd_analog_snd_controls, @@ -789,6 +1084,7 @@ static struct snd_soc_codec_driver pm8916_wcd_analog = { static int pm8916_wcd_analog_parse_dt(struct device *dev, struct pm8916_wcd_analog_priv *priv) { + int rval; if (of_property_read_bool(dev->of_node, "qcom,micbias1-ext-cap")) priv->micbias1_cap_mode = MICB_1_EN_EXT_BYP_CAP; @@ -803,6 +1099,39 @@ static int pm8916_wcd_analog_parse_dt(struct device *dev, of_property_read_u32(dev->of_node, "qcom,micbias-lvl", &priv->micbias_mv); + if (of_property_read_bool(dev->of_node, + "qcom,hphl-jack-type-normally-open")) + priv->hphl_jack_type_normally_open = true; + else + priv->hphl_jack_type_normally_open = false; + + if (of_property_read_bool(dev->of_node, + "qcom,gnd-jack-type-normally-open")) + priv->gnd_jack_type_normally_open = true; + else + priv->gnd_jack_type_normally_open = false; + + priv->mbhc_btn_enabled = true; + rval = of_property_read_u32_array(dev->of_node, + "qcom,mbhc-vthreshold-low", + &priv->vref_btn_cs[0], + MBHC_MAX_BUTTONS); + if (rval < 0) { + priv->mbhc_btn_enabled = false; + } else { + rval = of_property_read_u32_array(dev->of_node, + "qcom,mbhc-vthreshold-high", + &priv->vref_btn_micb[0], + MBHC_MAX_BUTTONS); + if (rval < 0) + priv->mbhc_btn_enabled = false; + } + + if (!priv->mbhc_btn_enabled) + dev_err(dev, + "DT property missing, MBHC btn detection disabled\n"); + + return 0; } @@ -810,7 +1139,7 @@ static int pm8916_wcd_analog_spmi_probe(struct platform_device *pdev) { struct pm8916_wcd_analog_priv *priv; struct device *dev = &pdev->dev; - int ret, i; + int ret, i, irq; priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); if (!priv) @@ -842,6 +1171,48 @@ static int pm8916_wcd_analog_spmi_probe(struct platform_device *pdev) return ret; } + irq = platform_get_irq_byname(pdev, "mbhc_switch_int"); + if (irq < 0) { + dev_err(dev, "failed to get mbhc switch irq\n"); + return irq; + } + + ret = devm_request_irq(dev, irq, pm8916_mbhc_switch_irq_handler, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | + IRQF_ONESHOT, + "mbhc switch irq", priv); + if (ret) + dev_err(dev, "cannot request mbhc switch irq\n"); + + if (priv->mbhc_btn_enabled) { + irq = platform_get_irq_byname(pdev, "mbhc_but_press_det"); + if (irq < 0) { + dev_err(dev, "failed to get button press irq\n"); + return irq; + } + + ret = devm_request_irq(dev, irq, mbhc_btn_press_irq_handler, + IRQF_TRIGGER_RISING | + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + "mbhc btn press irq", priv); + if (ret) + dev_err(dev, "cannot request mbhc button press irq\n"); + + irq = platform_get_irq_byname(pdev, "mbhc_but_rel_det"); + if (irq < 0) { + dev_err(dev, "failed to get button release irq\n"); + return irq; + } + + ret = devm_request_irq(dev, irq, mbhc_btn_release_irq_handler, + IRQF_TRIGGER_RISING | + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + "mbhc btn release irq", priv); + if (ret) + dev_err(dev, "cannot request mbhc button release irq\n"); + + } + dev_set_drvdata(dev, priv); return snd_soc_register_codec(dev, &pm8916_wcd_analog,

[v3,3/5] ASoC: codecs: msm8916-wcd-analog: add MBHC support

Commit Message

Comments

Patch