@@ -198,6 +198,13 @@ to specify in a pin configuration subnode:
in analog-pass-through mode.
Valid values are 1-4 corresponding to ATEST1 to ATEST4.
+- qcom,dtest-buffer:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects DTEST rail to route to GPIO when it's configured
+ as digital input.
+ Valid values are 1-4 corresponding to DTEST1 to DTEST4.
+
Example:
pm8921_gpio: gpio@150 {
@@ -51,6 +51,7 @@
#define PMIC_GPIO_REG_DIG_VIN_CTL 0x41
#define PMIC_GPIO_REG_DIG_PULL_CTL 0x42
#define PMIC_GPIO_REG_LV_MV_DIG_OUT_SOURCE_CTL 0x44
+#define PMIC_GPIO_REG_DIG_IN_CTL 0x43
#define PMIC_GPIO_REG_DIG_OUT_CTL 0x45
#define PMIC_GPIO_REG_EN_CTL 0x46
#define PMIC_GPIO_REG_LV_MV_ANA_PASS_THRU_SEL 0x4A
@@ -84,6 +85,11 @@
#define PMIC_GPIO_LV_MV_OUTPUT_INVERT_SHIFT 7
#define PMIC_GPIO_LV_MV_OUTPUT_SOURCE_SEL_MASK 0xF
+/* PMIC_GPIO_REG_DIG_IN_CTL */
+#define PMIC_GPIO_LV_MV_DIG_IN_DTEST_EN 0x80
+#define PMIC_GPIO_LV_MV_DIG_IN_DTEST_SEL_MASK 0x7
+#define PMIC_GPIO_DIG_IN_DTEST_SEL_MASK 0xf
+
/* PMIC_GPIO_REG_DIG_OUT_CTL */
#define PMIC_GPIO_REG_OUT_STRENGTH_SHIFT 0
#define PMIC_GPIO_REG_OUT_STRENGTH_MASK 0x3
@@ -111,6 +117,7 @@
#define PMIC_GPIO_CONF_STRENGTH (PIN_CONFIG_END + 2)
#define PMIC_GPIO_CONF_ATEST (PIN_CONFIG_END + 3)
#define PMIC_GPIO_CONF_ANALOG_PASS (PIN_CONFIG_END + 4)
+#define PMIC_GPIO_CONF_DTEST_BUFFER (PIN_CONFIG_END + 5)
/* The index of each function in pmic_gpio_functions[] array */
enum pmic_gpio_func_index {
@@ -145,6 +152,7 @@ enum pmic_gpio_func_index {
* @strength: No, Low, Medium, High
* @function: See pmic_gpio_functions[]
* @atest: the ATEST selection for GPIO analog-pass-through mode
+ * @dtest_buffer: the DTEST buffer selection for digital input mode.
*/
struct pmic_gpio_pad {
u16 base;
@@ -163,6 +171,7 @@ struct pmic_gpio_pad {
unsigned int strength;
unsigned int function;
unsigned int atest;
+ unsigned int dtest_buffer;
};
struct pmic_gpio_state {
@@ -177,6 +186,7 @@ struct pmic_gpio_state {
{"qcom,drive-strength", PMIC_GPIO_CONF_STRENGTH, 0},
{"qcom,atest", PMIC_GPIO_CONF_ATEST, 0},
{"qcom,analog-pass", PMIC_GPIO_CONF_ANALOG_PASS, 0},
+ {"qcom,dtest-buffer", PMIC_GPIO_CONF_DTEST_BUFFER, 0},
};
#ifdef CONFIG_DEBUG_FS
@@ -185,6 +195,7 @@ struct pmic_gpio_state {
PCONFDUMP(PMIC_GPIO_CONF_STRENGTH, "drive-strength", NULL, true),
PCONFDUMP(PMIC_GPIO_CONF_ATEST, "atest", NULL, true),
PCONFDUMP(PMIC_GPIO_CONF_ANALOG_PASS, "analog-pass", NULL, true),
+ PCONFDUMP(PMIC_GPIO_CONF_DTEST_BUFFER, "dtest-buffer", NULL, true),
};
#endif
@@ -420,6 +431,9 @@ static int pmic_gpio_config_get(struct pinctrl_dev *pctldev,
case PMIC_GPIO_CONF_ANALOG_PASS:
arg = pad->analog_pass;
break;
+ case PMIC_GPIO_CONF_DTEST_BUFFER:
+ arg = pad->dtest_buffer;
+ break;
default:
return -EINVAL;
}
@@ -504,6 +518,11 @@ static int pmic_gpio_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
return -EINVAL;
pad->analog_pass = true;
break;
+ case PMIC_GPIO_CONF_DTEST_BUFFER:
+ if (arg > 4)
+ return -EINVAL;
+ pad->dtest_buffer = arg;
+ break;
default:
return -EINVAL;
}
@@ -528,6 +547,20 @@ static int pmic_gpio_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
if (ret < 0)
return ret;
+ if (pad->dtest_buffer == 0) {
+ val = 0;
+ } else {
+ if (pad->lv_mv_type) {
+ val = pad->dtest_buffer - 1;
+ val |= PMIC_GPIO_LV_MV_DIG_IN_DTEST_EN;
+ } else {
+ val = BIT(pad->dtest_buffer - 1);
+ }
+ }
+ ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_DIG_IN_CTL, val);
+ if (ret < 0)
+ return ret;
+
if (pad->analog_pass)
val = PMIC_GPIO_MODE_ANALOG_PASS_THRU;
else if (pad->output_enabled && pad->input_enabled)
@@ -627,6 +660,7 @@ static void pmic_gpio_config_dbg_show(struct pinctrl_dev *pctldev,
seq_printf(s, " %-4s", pad->out_value ? "high" : "low");
seq_printf(s, " %-7s", strengths[pad->strength]);
seq_printf(s, " atest-%d", pad->atest);
+ seq_printf(s, " dtest-%d", pad->dtest_buffer);
}
}
@@ -845,6 +879,22 @@ static int pmic_gpio_populate(struct pmic_gpio_state *state,
pad->pullup = val >> PMIC_GPIO_REG_PULL_SHIFT;
pad->pullup &= PMIC_GPIO_REG_PULL_MASK;
+ val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_IN_CTL);
+ if (val < 0)
+ return val;
+
+ if (pad->lv_mv_type && (val & PMIC_GPIO_LV_MV_DIG_IN_DTEST_EN))
+ pad->dtest_buffer =
+ (val & PMIC_GPIO_LV_MV_DIG_IN_DTEST_SEL_MASK) + 1;
+ else if (!pad->lv_mv_type)
+ pad->dtest_buffer = ffs(val);
+ else
+ pad->dtest_buffer = 0;
+
+ val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_OUT_CTL);
+ if (val < 0)
+ return val;
+
pad->strength = val >> PMIC_GPIO_REG_OUT_STRENGTH_SHIFT;
pad->strength &= PMIC_GPIO_REG_OUT_STRENGTH_MASK;