@@ -10,6 +10,15 @@ compatible = "axentia,linea",
and following the rules from atmel-at91.txt for a sama5d31 SoC.
+Nattis v2 board with Natte v2 power board
+-----------------------------------------
+
+Required root node properties:
+compatible = "axentia,nattis-2", "axentia,natte-2", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+and following the rules from above for the axentia,linea CPU module.
+
+
TSE-850 v3 board
----------------
@@ -2500,6 +2500,8 @@ L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: Documentation/devicetree/bindings/arm/axentia.txt
F: arch/arm/boot/dts/at91-linea.dtsi
+F: arch/arm/boot/dts/at91-natte.dtsi
+F: arch/arm/boot/dts/at91-nattis-2-natte-2.dts
F: arch/arm/boot/dts/at91-tse850-3.dts
AXENTIA ASOC DRIVERS
@@ -47,6 +47,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
at91sam9x35ek.dtb
dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
+ at91-nattis-2-natte-2.dtb \
at91-sama5d27_som1_ek.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
new file mode 100644
@@ -0,0 +1,244 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * at91-natte.dts - Device Tree include file for the Natte board
+ *
+ * Copyright (C) 2017 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda@axentia.se>
+ */
+
+/ {
+ mux: mux-controller {
+ compatible = "gpio-mux";
+ #mux-control-cells = <0>;
+
+ mux-gpios = <&ioexp 0 GPIO_ACTIVE_HIGH>,
+ <&ioexp 1 GPIO_ACTIVE_HIGH>,
+ <&ioexp 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ batntc-mux {
+ compatible = "io-channel-mux";
+ io-channels = <&adc 5>;
+ io-channel-names = "parent";
+ mux-controls = <&mux>;
+
+ channels =
+ "batntc0", "batntc1", "batntc2", "batntc3",
+ "batntc4", "batntc5", "batntc6", "batntc7";
+ };
+
+ batv-mux {
+ compatible = "io-channel-mux";
+ io-channels = <&adc 6>;
+ io-channel-names = "parent";
+ mux-controls = <&mux>;
+
+ channels =
+ "batv0", "batv1", "batv2", "batv3",
+ "batv4", "batv5", "batv6", "batv7";
+ };
+
+ iout-mux {
+ compatible = "io-channel-mux";
+ io-channels = <&adc 7>;
+ io-channel-names = "parent";
+ mux-controls = <&mux>;
+
+ channels =
+ "iout0", "iout1", "iout2", "iout3",
+ "iout4", "iout5", "iout6", "iout7";
+ };
+
+ i2c-mux {
+ compatible = "i2c-mux";
+ mux-locked;
+ i2c-parent = <&i2c0>;
+ mux-controls = <&mux>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@9 {
+ compatible = "ti,bq24735";
+ reg = <0x9>;
+
+ ti,charge-current = <2000>;
+ ti,charge-voltage = <16800>;
+
+ poll-interval = <20000>;
+ };
+ };
+
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@9 {
+ compatible = "ti,bq24735";
+ reg = <0x9>;
+
+ ti,charge-current = <2000>;
+ ti,charge-voltage = <16800>;
+
+ poll-interval = <20000>;
+ };
+ };
+
+ i2c@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@9 {
+ compatible = "ti,bq24735";
+ reg = <0x9>;
+
+ ti,charge-current = <2000>;
+ ti,charge-voltage = <16800>;
+
+ poll-interval = <20000>;
+ };
+ };
+
+ i2c@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@9 {
+ compatible = "ti,bq24735";
+ reg = <0x9>;
+
+ ti,charge-current = <2000>;
+ ti,charge-voltage = <16800>;
+
+ poll-interval = <20000>;
+ };
+ };
+
+ i2c@4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@9 {
+ compatible = "ti,bq24735";
+ reg = <0x9>;
+
+ ti,charge-current = <2000>;
+ ti,charge-voltage = <16800>;
+
+ poll-interval = <20000>;
+ };
+ };
+
+ i2c@5 {
+ reg = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@9 {
+ compatible = "ti,bq24735";
+ reg = <0x9>;
+
+ ti,charge-current = <2000>;
+ ti,charge-voltage = <16800>;
+
+ poll-interval = <20000>;
+ };
+ };
+
+ i2c@6 {
+ reg = <6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@9 {
+ compatible = "ti,bq24735";
+ reg = <0x9>;
+
+ ti,charge-current = <2000>;
+ ti,charge-voltage = <16800>;
+
+ poll-interval = <20000>;
+ };
+ };
+
+ i2c@7 {
+ reg = <7>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@9 {
+ compatible = "ti,bq24735";
+ reg = <0x9>;
+
+ ti,charge-current = <2000>;
+ ti,charge-voltage = <16800>;
+
+ poll-interval = <20000>;
+ };
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ ioexp: ioexp@20 {
+ #gpio-cells = <2>;
+ compatible = "semtech,sx1502q";
+ reg = <0x20>;
+
+ gpio-controller;
+ ngpios = <8>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio3_cfg_pins>;
+
+ gpio3_cfg_pins: gpio3_cfg {
+ pins = "gpio3";
+ bias-pull-up;
+ };
+ };
+
+ adc: adc@48 {
+ compatible = "ti,ads1015";
+ reg = <0x48>;
+ #io-channel-cells = <1>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@4 {
+ reg = <4>;
+ ti,gain = <2>;
+ ti,datarate = <4>;
+ };
+
+ channel@5 {
+ reg = <5>;
+ ti,gain = <2>;
+ ti,datarate = <4>;
+ };
+
+ channel@6 {
+ reg = <6>;
+ ti,gain = <1>;
+ ti,datarate = <4>;
+ };
+
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <4>;
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * at91-nattis-2-natte-2.dts - Device Tree file for the Linea/Nattis board
+ *
+ * Copyright (C) 2017 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda@axentia.se>
+ */
+/dts-v1/;
+#include "at91-linea.dtsi"
+#include "sama5d3_lcd.dtsi"
+#include "at91-natte.dtsi"
+
+/ {
+ model = "Axentia Linea-Nattis v2 Natte v2";
+ compatible = "axentia,nattis-2", "axentia,natte-2", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ pinctrl@fffff200 {
+ nattis {
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOD 28
+ AT91_PERIPH_GPIO
+ AT91_PINCTRL_DEGLITCH>;
+ };
+
+ pinctrl_mmc0_cd: mmc0_cd {
+ atmel,pins =
+ <AT91_PIOD 5
+ AT91_PERIPH_GPIO
+ AT91_PINCTRL_PULL_UP_DEGLITCH>;
+ };
+
+ pinctrl_lcd_prlud0: lcd_prlud0 {
+ atmel,pins =
+ <AT91_PIOA 21
+ AT91_PERIPH_GPIO
+ AT91_PINCTRL_OUTPUT_VAL(0)>;
+ };
+
+ pinctrl_lcd_hipow0: lcd_hipow0 {
+ atmel,pins =
+ <AT91_PIOA 23
+ AT91_PERIPH_GPIO
+ AT91_PINCTRL_OUTPUT_VAL(0)>;
+ };
+ };
+ };
+
+ watchdog@fffffe40 {
+ status = "okay";
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ wakeup {
+ label = "Wakeup";
+ linux,code = <10>;
+ gpio-key,wakeup;
+ gpios = <&pioB 27 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ panel_reg: panel-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "panel-VCC";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ bl_reg: backlight-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "panel-VDD";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ panel_bl: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&hlcdc_pwm 0 100000 0>;
+
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <40>;
+
+ power-supply = <&bl_reg>;
+ enable-gpios = <&pioA 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ panel: panel {
+ compatible = "sharp,lq150x1lg11";
+ backlight = <&panel_bl>;
+ power-supply = <&panel_reg>;
+
+ port {
+ panel_input: endpoint {
+ remote-endpoint = <&hlcdc_panel_output>;
+ };
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+
+ simple-audio-card,name = "nattis-tfa9879";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&cpu_dai>;
+ simple-audio-card,frame-master = <&cpu_dai>;
+ simple-audio-card,widgets = "Line", "Line Out Jack";
+ simple-audio-card,routing = "Line Out Jack", "LINEOUT";
+
+ cpu_dai: simple-audio-card,cpu {
+ sound-dai = <&ssc0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&>;
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ clock-frequency = <100000>;
+
+ temp@18 {
+ compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+ reg = <0x18>;
+ smbus-timeout-disable;
+ };
+
+ eeprom@50 {
+ compatible = "nxp,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+
+ amp: amplifier@6c {
+ compatible = "nxp,tfa9879";
+ reg = <0x6c>;
+ #sound-dai-cells = <0>;
+ };
+};
+
+&ssc0 {
+ status = "okay";
+
+ atmel,clk-from-rk-pin;
+ #sound-dai-cells = <0>;
+};
+
+&hlcdc {
+ status = "okay";
+
+ hlcdc-display-controller {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_base
+ &pinctrl_lcd_rgb565
+ &pinctrl_lcd_prlud0
+ &pinctrl_lcd_hipow0>;
+
+ port@0 {
+ hlcdc_panel_output: endpoint {
+ remote-endpoint = <&panel_input>;
+ };
+ };
+ };
+};
+
+&mmc0 {
+ status = "okay";
+
+ pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0
+ &pinctrl_mmc0_dat1_3
+ &pinctrl_mmc0_cd>;
+
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&usart0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart0>;
+ atmel,use-dma-rx;
+};
+
+&nand {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ bootloader@40000 {
+ label = "bootloader";
+ reg = <0x40000 0x80000>;
+ };
+
+ bootloaderenv@c0000 {
+ label = "bootloader env";
+ reg = <0xc0000 0xc0000>;
+ };
+
+ dtb@180000 {
+ label = "device tree";
+ reg = <0x180000 0x80000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x600000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+ };
+};
+
+&dbgu {
+ status = "okay";
+
+ atmel,use-dma-rx;
+};
+
+&usb0 {
+ status = "okay";
+
+ atmel,vbus-gpio = <&pioD 28 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+};
The Axentia Nattis is a device designed for presenting departures for public transport systems. The Natte helper board provides power and features a battery of battery chargers. Signed-off-by: Peter Rosin <peda@axentia.se> --- This was part of a two-patch series, but the first patch in that series was redundant, so I dropped it (there was a dt binding recently added for the tfa9879 amplifier that I had not noticed). Changes since v1: https://lkml.org/lkml/2017/12/1/844 - removed chip-ids from before the @-sign instead naming the nodes for the function, e.g sx1502q@20 -> ioexp@20 - added #sound-dai-cells to the amplifier node - switch to SPDX license tags Cheers, Peter Documentation/devicetree/bindings/arm/axentia.txt | 9 + MAINTAINERS | 2 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/at91-natte.dtsi | 244 ++++++++++++++++++++ arch/arm/boot/dts/at91-nattis-2-natte-2.dts | 258 ++++++++++++++++++++++ 5 files changed, 514 insertions(+) create mode 100644 arch/arm/boot/dts/at91-natte.dtsi create mode 100644 arch/arm/boot/dts/at91-nattis-2-natte-2.dts