| Message ID | 20180110141226.27826-4-linus.walleij@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Linus Walleij <linus.walleij@linaro.org> writes: > If the bridge has a too strict setup time for the incoming > signals, we may not be fast enough and then we need to > compensate by outputting the signal on the inverse clock > edge so it is for sure stable when the bridge samples it. > > Since bridges in difference to panels does not expose their > connectors, make the connector optional in the display > setup code. > > Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> > --- > ChangeLog v5->v6: > - Collect Laurent's ACK. > ChangeLog v4->v5: > - Use the new bridge timings setup method. > --- > drivers/gpu/drm/pl111/Kconfig | 1 + > drivers/gpu/drm/pl111/pl111_display.c | 35 +++++++++++++++++++++++++++++++---- > drivers/gpu/drm/pl111/pl111_drv.c | 20 +++++++++++--------- > 3 files changed, 43 insertions(+), 13 deletions(-) > > diff --git a/drivers/gpu/drm/pl111/Kconfig b/drivers/gpu/drm/pl111/Kconfig > index e5e2abd66491..82cb3e60ddc8 100644 > --- a/drivers/gpu/drm/pl111/Kconfig > +++ b/drivers/gpu/drm/pl111/Kconfig > @@ -8,6 +8,7 @@ config DRM_PL111 > select DRM_GEM_CMA_HELPER > select DRM_BRIDGE > select DRM_PANEL_BRIDGE > + select DRM_DUMB_VGA_DAC > select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE > help > Choose this option for DRM support for the PL111 CLCD controller. Should this be in PL111, or in whatever machine is a consumer of this driver plus a dumb dac? I'm OK either way, it's not a big deal for the platform I've got. > diff --git a/drivers/gpu/drm/pl111/pl111_drv.c b/drivers/gpu/drm/pl111/pl111_drv.c > index 201d57d5cb54..101a9c7db6ff 100644 > --- a/drivers/gpu/drm/pl111/pl111_drv.c > +++ b/drivers/gpu/drm/pl111/pl111_drv.c > @@ -107,11 +107,17 @@ static int pl111_modeset_init(struct drm_device *dev) > ret = PTR_ERR(bridge); > goto out_config; > } > - /* > - * TODO: when we are using a different bridge than a panel > - * (such as a dumb VGA connector) we need to devise a different > - * method to get the connector out of the bridge. > - */ > + } else if (bridge) { > + dev_info(dev->dev, "Using non-panel bridge\n"); This looks like it might be a debug printf you didn't intend to leave in. Either way, the patch gets my: Reviewed-by: Eric Anholt <eric@anholt.net>
diff --git a/drivers/gpu/drm/pl111/Kconfig b/drivers/gpu/drm/pl111/Kconfig index e5e2abd66491..82cb3e60ddc8 100644 --- a/drivers/gpu/drm/pl111/Kconfig +++ b/drivers/gpu/drm/pl111/Kconfig @@ -8,6 +8,7 @@ config DRM_PL111 select DRM_GEM_CMA_HELPER select DRM_BRIDGE select DRM_PANEL_BRIDGE + select DRM_DUMB_VGA_DAC select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE help Choose this option for DRM support for the PL111 CLCD controller. diff --git a/drivers/gpu/drm/pl111/pl111_display.c b/drivers/gpu/drm/pl111/pl111_display.c index 06c4bf756b69..7fe4040aea46 100644 --- a/drivers/gpu/drm/pl111/pl111_display.c +++ b/drivers/gpu/drm/pl111/pl111_display.c @@ -94,6 +94,7 @@ static void pl111_display_enable(struct drm_simple_display_pipe *pipe, const struct drm_display_mode *mode = &cstate->mode; struct drm_framebuffer *fb = plane->state->fb; struct drm_connector *connector = priv->connector; + struct drm_bridge *bridge = priv->bridge; u32 cntl; u32 ppl, hsw, hfp, hbp; u32 lpp, vsw, vfp, vbp; @@ -143,11 +144,37 @@ static void pl111_display_enable(struct drm_simple_display_pipe *pipe, if (mode->flags & DRM_MODE_FLAG_NVSYNC) tim2 |= TIM2_IVS; - if (connector->display_info.bus_flags & DRM_BUS_FLAG_DE_LOW) - tim2 |= TIM2_IOE; + if (connector) { + if (connector->display_info.bus_flags & DRM_BUS_FLAG_DE_LOW) + tim2 |= TIM2_IOE; - if (connector->display_info.bus_flags & DRM_BUS_FLAG_PIXDATA_NEGEDGE) - tim2 |= TIM2_IPC; + if (connector->display_info.bus_flags & + DRM_BUS_FLAG_PIXDATA_NEGEDGE) + tim2 |= TIM2_IPC; + } + + if (bridge) { + const struct drm_bridge_timings *btimings = bridge->timings; + + /* + * Here is when things get really fun. Sometimes the bridge + * timings are such that the signal out from PL11x is not + * stable before the receiving bridge (such as a dumb VGA DAC + * or similar) samples it. If that happens, we compensate by + * the only method we have: output the data on the opposite + * edge of the clock so it is for sure stable when it gets + * sampled. + * + * The PL111 manual does not contain proper timining diagrams + * or data for these details, but we know from experiments + * that the setup time is more than 3000 picoseconds (3 ns). + * If we have a bridge that requires the signal to be stable + * earlier than 3000 ps before the clock pulse, we have to + * output the data on the opposite edge to avoid flicker. + */ + if (btimings && btimings->setup_time_ps >= 3000) + tim2 ^= TIM2_IPC; + } tim2 |= cpl << 16; writel(tim2, priv->regs + CLCD_TIM2); diff --git a/drivers/gpu/drm/pl111/pl111_drv.c b/drivers/gpu/drm/pl111/pl111_drv.c index 201d57d5cb54..101a9c7db6ff 100644 --- a/drivers/gpu/drm/pl111/pl111_drv.c +++ b/drivers/gpu/drm/pl111/pl111_drv.c @@ -107,11 +107,17 @@ static int pl111_modeset_init(struct drm_device *dev) ret = PTR_ERR(bridge); goto out_config; } - /* - * TODO: when we are using a different bridge than a panel - * (such as a dumb VGA connector) we need to devise a different - * method to get the connector out of the bridge. - */ + } else if (bridge) { + dev_info(dev->dev, "Using non-panel bridge\n"); + } else { + dev_err(dev->dev, "No bridge, exiting\n"); + return -ENODEV; + } + + priv->bridge = bridge; + if (panel) { + priv->panel = panel; + priv->connector = panel->connector; } ret = pl111_display_init(dev); @@ -125,10 +131,6 @@ static int pl111_modeset_init(struct drm_device *dev) if (ret) return ret; - priv->bridge = bridge; - priv->panel = panel; - priv->connector = panel->connector; - ret = drm_vblank_init(dev, 1); if (ret != 0) { dev_err(dev->dev, "Failed to init vblank\n");