@@ -995,6 +995,17 @@ config I2C_SUN6I_P2WI
This interface is used to connect to specific PMIC devices (like the
AXP221).
+config I2C_SYNQUACER
+ tristate "Socionext SynQuacer I2C controller"
+ depends on ARCH_SYNQUACER || COMPILE_TEST
+ depends on OF || ACPI
+ help
+ Say Y here to include support for the I2C controller used in some
+ Fujitsu and Socionext SoCs.
+
+ This driver can also be built as a module. If so, the module
+ will be called i2c-synquacer.
+
config I2C_TEGRA
tristate "NVIDIA Tegra internal I2C controller"
depends on ARCH_TEGRA
@@ -98,6 +98,7 @@ obj-$(CONFIG_I2C_STM32F4) += i2c-stm32f4.o
obj-$(CONFIG_I2C_STM32F7) += i2c-stm32f7.o
obj-$(CONFIG_I2C_STU300) += i2c-stu300.o
obj-$(CONFIG_I2C_SUN6I_P2WI) += i2c-sun6i-p2wi.o
+obj-$(CONFIG_I2C_SYNQUACER) += i2c-synquacer.o
obj-$(CONFIG_I2C_TEGRA) += i2c-tegra.o
obj-$(CONFIG_I2C_TEGRA_BPMP) += i2c-tegra-bpmp.o
obj-$(CONFIG_I2C_UNIPHIER) += i2c-uniphier.o
new file mode 100644
@@ -0,0 +1,817 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2012 FUJITSU SEMICONDUCTOR LIMITED
+ */
+
+#include <linux/acpi.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+#define WAIT_PCLK(n, rate) ndelay((((1000000000 + (rate) - 1) / \
+ (rate) + n - 1) / n) + 10)
+#define SYNQUACER_I2C_TIMEOUT(x) (msecs_to_jiffies(x))
+
+/* I2C register adress definitions */
+#define SYNQUACER_I2C_REG_BSR (0x00 << 2) // Bus Status
+#define SYNQUACER_I2C_REG_BCR (0x01 << 2) // Bus Control
+#define SYNQUACER_I2C_REG_CCR (0x02 << 2) // Clock Control
+#define SYNQUACER_I2C_REG_ADR (0x03 << 2) // Address
+#define SYNQUACER_I2C_REG_DAR (0x04 << 2) // Data
+#define SYNQUACER_I2C_REG_CSR (0x05 << 2) // Expansion CS
+#define SYNQUACER_I2C_REG_FSR (0x06 << 2) // Bus Clock Freq
+#define SYNQUACER_I2C_REG_BC2R (0x07 << 2) // Bus Control 2
+
+/* I2C register bit definitions */
+#define SYNQUACER_I2C_BSR_FBT BIT(0) // First Byte Transfer
+#define SYNQUACER_I2C_BSR_GCA BIT(1) // General Call Address
+#define SYNQUACER_I2C_BSR_AAS BIT(2) // Address as Slave
+#define SYNQUACER_I2C_BSR_TRX BIT(3) // Transfer/Receive
+#define SYNQUACER_I2C_BSR_LRB BIT(4) // Last Received Bit
+#define SYNQUACER_I2C_BSR_AL BIT(5) // Arbitration Lost
+#define SYNQUACER_I2C_BSR_RSC BIT(6) // Repeated Start Cond.
+#define SYNQUACER_I2C_BSR_BB BIT(7) // Bus Busy
+
+#define SYNQUACER_I2C_BCR_INT BIT(0) // Interrupt
+#define SYNQUACER_I2C_BCR_INTE BIT(1) // Interrupt Enable
+#define SYNQUACER_I2C_BCR_GCAA BIT(2) // Gen. Call Access Ack.
+#define SYNQUACER_I2C_BCR_ACK BIT(3) // Acknowledge
+#define SYNQUACER_I2C_BCR_MSS BIT(4) // Master Slave Select
+#define SYNQUACER_I2C_BCR_SCC BIT(5) // Start Condition Cont.
+#define SYNQUACER_I2C_BCR_BEIE BIT(6) // Bus Error Int Enable
+#define SYNQUACER_I2C_BCR_BER BIT(7) // Bus Error
+
+#define SYNQUACER_I2C_CCR_CS_MASK (0x1f) // CCR Clock Period Sel.
+#define SYNQUACER_I2C_CCR_EN BIT(5) // Enable
+#define SYNQUACER_I2C_CCR_FM BIT(6) // Speed Mode Select
+
+#define SYNQUACER_I2C_CSR_CS_MASK (0x3f) // CSR Clock Period Sel.
+
+#define SYNQUACER_I2C_BC2R_SCLL BIT(0) // SCL Low Drive
+#define SYNQUACER_I2C_BC2R_SDAL BIT(1) // SDA Low Drive
+#define SYNQUACER_I2C_BC2R_SCLS BIT(4) // SCL Status
+#define SYNQUACER_I2C_BC2R_SDAS BIT(5) // SDA Status
+
+/* PCLK frequency */
+#define SYNQUACER_I2C_BUS_CLK_FR(rate) (((rate) / 20000000) + 1)
+
+/* STANDARD MODE frequency */
+#define SYNQUACER_I2C_CLK_MASTER_STD(rate) \
+ DIV_ROUND_UP(DIV_ROUND_UP((rate), 100000) - 2, 2)
+/* FAST MODE frequency */
+#define SYNQUACER_I2C_CLK_MASTER_FAST(rate) \
+ DIV_ROUND_UP((DIV_ROUND_UP((rate), 400000) - 2) * 2, 3)
+
+/* (clkrate <= 18000000) */
+/* calculate the value of CS bits in CCR register on standard mode */
+#define SYNQUACER_I2C_CCR_CS_STD_MAX_18M(rate) \
+ ((SYNQUACER_I2C_CLK_MASTER_STD(rate) - 65) \
+ & SYNQUACER_I2C_CCR_CS_MASK)
+
+/* calculate the value of CS bits in CSR register on standard mode */
+#define SYNQUACER_I2C_CSR_CS_STD_MAX_18M(rate) 0x00
+
+/* calculate the value of CS bits in CCR register on fast mode */
+#define SYNQUACER_I2C_CCR_CS_FAST_MAX_18M(rate) \
+ ((SYNQUACER_I2C_CLK_MASTER_FAST(rate) - 1) \
+ & SYNQUACER_I2C_CCR_CS_MASK)
+
+/* calculate the value of CS bits in CSR register on fast mode */
+#define SYNQUACER_I2C_CSR_CS_FAST_MAX_18M(rate) 0x00
+
+/* (clkrate > 18000000) */
+/* calculate the value of CS bits in CCR register on standard mode */
+#define SYNQUACER_I2C_CCR_CS_STD_MIN_18M(rate) \
+ ((SYNQUACER_I2C_CLK_MASTER_STD(rate) - 1) \
+ & SYNQUACER_I2C_CCR_CS_MASK)
+
+/* calculate the value of CS bits in CSR register on standard mode */
+#define SYNQUACER_I2C_CSR_CS_STD_MIN_18M(rate) \
+ (((SYNQUACER_I2C_CLK_MASTER_STD(rate) - 1) >> 5) \
+ & SYNQUACER_I2C_CSR_CS_MASK)
+
+/* calculate the value of CS bits in CCR register on fast mode */
+#define SYNQUACER_I2C_CCR_CS_FAST_MIN_18M(rate) \
+ ((SYNQUACER_I2C_CLK_MASTER_FAST(rate) - 1) \
+ & SYNQUACER_I2C_CCR_CS_MASK)
+
+/* calculate the value of CS bits in CSR register on fast mode */
+#define SYNQUACER_I2C_CSR_CS_FAST_MIN_18M(rate) \
+ (((SYNQUACER_I2C_CLK_MASTER_FAST(rate) - 1) >> 5) \
+ & SYNQUACER_I2C_CSR_CS_MASK)
+
+/* min I2C clock frequency 14M */
+#define SYNQUACER_I2C_MIN_CLK_RATE (14 * 1000000)
+/* max I2C clock frequency 200M */
+#define SYNQUACER_I2C_MAX_CLK_RATE (200 * 1000000)
+/* I2C clock frequency 18M */
+#define SYNQUACER_I2C_CLK_RATE_18M (18 * 1000000)
+
+#define SYNQUACER_I2C_SPEED_FM 400 // Fast Mode
+#define SYNQUACER_I2C_SPEED_SM 100 // Standard Mode
+
+enum i2c_state {
+ STATE_IDLE,
+ STATE_START,
+ STATE_READ,
+ STATE_WRITE
+};
+
+struct synquacer_i2c {
+ struct completion completion;
+
+ struct i2c_msg *msg;
+ u32 msg_num;
+ u32 msg_idx;
+ u32 msg_ptr;
+
+ u32 irq;
+ struct device *dev;
+ void __iomem *base;
+ struct clk *clk;
+ u32 clkrate;
+ u32 speed_khz;
+ u32 timeout_ms;
+ enum i2c_state state;
+ struct i2c_adapter adapter;
+
+ bool is_suspended;
+};
+
+static inline int is_lastmsg(struct synquacer_i2c *i2c)
+{
+ return i2c->msg_idx >= (i2c->msg_num - 1);
+}
+
+static inline int is_msglast(struct synquacer_i2c *i2c)
+{
+ return i2c->msg_ptr == (i2c->msg->len - 1);
+}
+
+static inline int is_msgend(struct synquacer_i2c *i2c)
+{
+ return i2c->msg_ptr >= i2c->msg->len;
+}
+
+static inline unsigned long calc_timeout_ms(struct synquacer_i2c *i2c,
+ struct i2c_msg *msgs,
+ int num)
+{
+ unsigned long bit_count = 0;
+ int i;
+
+ for (i = 0; i < num; i++, msgs++)
+ bit_count += msgs->len;
+
+ return DIV_ROUND_UP(((bit_count * 9) + (10 * num)) * 3, 200) + 10;
+}
+
+static void synquacer_i2c_stop(struct synquacer_i2c *i2c, int ret)
+{
+ dev_dbg(i2c->dev, "STOP\n");
+
+ /*
+ * clear IRQ (INT=0, BER=0)
+ * set Stop Condition (MSS=0)
+ * Interrupt Disable
+ */
+ writeb(0, i2c->base + SYNQUACER_I2C_REG_BCR);
+
+ i2c->state = STATE_IDLE;
+
+ i2c->msg_ptr = 0;
+ i2c->msg = NULL;
+ i2c->msg_idx++;
+ i2c->msg_num = 0;
+ if (ret)
+ i2c->msg_idx = ret;
+
+ complete(&i2c->completion);
+}
+
+static void synquacer_i2c_hw_init(struct synquacer_i2c *i2c)
+{
+ unsigned char ccr_cs, csr_cs;
+ u32 rt = i2c->clkrate;
+
+ /* Set own Address */
+ writeb(0, i2c->base + SYNQUACER_I2C_REG_ADR);
+
+ /* Set PCLK frequency */
+ writeb(SYNQUACER_I2C_BUS_CLK_FR(i2c->clkrate),
+ i2c->base + SYNQUACER_I2C_REG_FSR);
+
+ switch (i2c->speed_khz) {
+ case SYNQUACER_I2C_SPEED_FM:
+ if (i2c->clkrate <= SYNQUACER_I2C_CLK_RATE_18M) {
+ ccr_cs = SYNQUACER_I2C_CCR_CS_FAST_MAX_18M(rt);
+ csr_cs = SYNQUACER_I2C_CSR_CS_FAST_MAX_18M(rt);
+ } else {
+ ccr_cs = SYNQUACER_I2C_CCR_CS_FAST_MIN_18M(rt);
+ csr_cs = SYNQUACER_I2C_CSR_CS_FAST_MIN_18M(rt);
+ }
+
+ /* Set Clock and enable, Set fast mode*/
+ writeb(ccr_cs | SYNQUACER_I2C_CCR_FM |
+ SYNQUACER_I2C_CCR_EN,
+ i2c->base + SYNQUACER_I2C_REG_CCR);
+ writeb(csr_cs, i2c->base + SYNQUACER_I2C_REG_CSR);
+ break;
+ case SYNQUACER_I2C_SPEED_SM:
+ if (i2c->clkrate <= SYNQUACER_I2C_CLK_RATE_18M) {
+ ccr_cs = SYNQUACER_I2C_CCR_CS_STD_MAX_18M(rt);
+ csr_cs = SYNQUACER_I2C_CSR_CS_STD_MAX_18M(rt);
+ } else {
+ ccr_cs = SYNQUACER_I2C_CCR_CS_STD_MIN_18M(rt);
+ csr_cs = SYNQUACER_I2C_CSR_CS_STD_MIN_18M(rt);
+ }
+
+ /* Set Clock and enable, Set standard mode */
+ writeb(ccr_cs | SYNQUACER_I2C_CCR_EN,
+ i2c->base + SYNQUACER_I2C_REG_CCR);
+ writeb(csr_cs, i2c->base + SYNQUACER_I2C_REG_CSR);
+ break;
+ default:
+ BUG();
+ }
+
+ /* clear IRQ (INT=0, BER=0), Interrupt Disable */
+ writeb(0, i2c->base + SYNQUACER_I2C_REG_BCR);
+ writeb(0, i2c->base + SYNQUACER_I2C_REG_BC2R);
+}
+
+static void synquacer_i2c_hw_reset(struct synquacer_i2c *i2c)
+{
+ /* Disable clock */
+ writeb(0, i2c->base + SYNQUACER_I2C_REG_CCR);
+ writeb(0, i2c->base + SYNQUACER_I2C_REG_CSR);
+
+ WAIT_PCLK(100, i2c->clkrate);
+
+ synquacer_i2c_hw_init(i2c);
+}
+
+static int synquacer_i2c_master_start(struct synquacer_i2c *i2c,
+ struct i2c_msg *pmsg)
+{
+ unsigned char bsr, bcr;
+
+ if (pmsg->flags & I2C_M_RD)
+ writeb((pmsg->addr << 1) | 1,
+ i2c->base + SYNQUACER_I2C_REG_DAR);
+ else
+ writeb(pmsg->addr << 1,
+ i2c->base + SYNQUACER_I2C_REG_DAR);
+
+ dev_dbg(i2c->dev, "%s slave:0x%02x\n", __func__, pmsg->addr);
+
+ /* Generate Start Condition */
+ bsr = readb(i2c->base + SYNQUACER_I2C_REG_BSR);
+ bcr = readb(i2c->base + SYNQUACER_I2C_REG_BCR);
+ dev_dbg(i2c->dev, "%s bsr:0x%08x, bcr:0x%08x\n", __func__, bsr,
+ bcr);
+
+ if ((bsr & SYNQUACER_I2C_BSR_BB) &&
+ !(bcr & SYNQUACER_I2C_BCR_MSS)) {
+ dev_dbg(i2c->dev, "%s bus is busy", __func__);
+ return -EBUSY;
+ }
+
+ if (bsr & SYNQUACER_I2C_BSR_BB) { /* Bus is busy */
+ dev_dbg(i2c->dev, "%s Continuous Start", __func__);
+ writeb(bcr | SYNQUACER_I2C_BCR_SCC,
+ i2c->base + SYNQUACER_I2C_REG_BCR);
+ } else {
+ if (bcr & SYNQUACER_I2C_BCR_MSS) {
+ dev_dbg(i2c->dev, "%s is not in master mode",
+ __func__);
+ return -EAGAIN;
+ }
+ dev_dbg(i2c->dev, "%s Start Condition", __func__);
+ /* Start Condition + Enable Interrupts */
+ writeb(bcr | SYNQUACER_I2C_BCR_MSS |
+ SYNQUACER_I2C_BCR_INTE | SYNQUACER_I2C_BCR_BEIE,
+ i2c->base + SYNQUACER_I2C_REG_BCR);
+ }
+
+ WAIT_PCLK(10, i2c->clkrate);
+
+ /* get bsr&bcr register */
+ bsr = readb(i2c->base + SYNQUACER_I2C_REG_BSR);
+ bcr = readb(i2c->base + SYNQUACER_I2C_REG_BCR);
+ dev_dbg(i2c->dev, "%s bsr:0x%08x, bcr:0x%08x\n", __func__, bsr,
+ bcr);
+
+ if ((bsr & SYNQUACER_I2C_BSR_AL) ||
+ !(bcr & SYNQUACER_I2C_BCR_MSS)) {
+ dev_dbg(i2c->dev, "%s arbitration lost\n", __func__);
+ return -EAGAIN;
+ }
+
+ return 0;
+}
+
+static int synquacer_i2c_master_recover(struct synquacer_i2c *i2c)
+{
+ unsigned int count = 0;
+ unsigned char bc2r;
+
+ /* Disable interrupts */
+ writeb(0, i2c->base + SYNQUACER_I2C_REG_BCR);
+
+ /* monitor SDA, SCL */
+ bc2r = readb(i2c->base + SYNQUACER_I2C_REG_BC2R);
+ dev_dbg(i2c->dev, "%s bc2r:0x%02x\n", __func__, bc2r);
+
+ while (count <= 100) {
+ WAIT_PCLK(20, i2c->clkrate);
+ bc2r = readb(i2c->base + SYNQUACER_I2C_REG_BC2R);
+
+ /* another master is running */
+ if ((bc2r & SYNQUACER_I2C_BC2R_SDAS) ||
+ !(bc2r & SYNQUACER_I2C_BC2R_SCLS)) {
+ dev_dbg(i2c->dev, "%s: another master is running?\n",
+ __func__);
+ return -EAGAIN;
+ }
+ count++;
+ }
+
+ /* Force to make one clock pulse */
+ count = 0;
+ for (;;) {
+ /* SCL = L->H */
+ writeb(SYNQUACER_I2C_BC2R_SCLL,
+ i2c->base + SYNQUACER_I2C_REG_BC2R);
+ WAIT_PCLK(20, i2c->clkrate);
+ writeb(0, i2c->base + SYNQUACER_I2C_REG_BC2R);
+
+ WAIT_PCLK(10, i2c->clkrate);
+
+ bc2r = readb(i2c->base + SYNQUACER_I2C_REG_BC2R);
+
+ WAIT_PCLK(5, i2c->clkrate);
+
+ if (bc2r & SYNQUACER_I2C_BC2R_SDAS)
+ break;
+ WAIT_PCLK(10, i2c->clkrate);
+ if (++count > 9) {
+ dev_err(i2c->dev, "%s: count: %i, bc2r: 0x%x\n",
+ __func__, count, bc2r);
+ return -EIO;
+ }
+ }
+
+ /* force to make bus-error phase */
+ /* SDA = L */
+ writeb(SYNQUACER_I2C_BC2R_SDAL,
+ i2c->base + SYNQUACER_I2C_REG_BC2R);
+ WAIT_PCLK(10, i2c->clkrate);
+ /* SDA = H */
+ writeb(0, i2c->base + SYNQUACER_I2C_REG_BC2R);
+ WAIT_PCLK(10, i2c->clkrate);
+
+ /* Both SDA & SDL should be H */
+ bc2r = readb(i2c->base + SYNQUACER_I2C_REG_BC2R);
+ if ((bc2r & (SYNQUACER_I2C_BC2R_SDAS | SYNQUACER_I2C_BC2R_SCLS))
+ != (SYNQUACER_I2C_BC2R_SDAS | SYNQUACER_I2C_BC2R_SCLS)) {
+ dev_err(i2c->dev, "%s: bc2r: 0x%x\n", __func__, bc2r);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int synquacer_i2c_doxfer(struct synquacer_i2c *i2c,
+ struct i2c_msg *msgs, int num)
+{
+ unsigned char bsr;
+ unsigned long timeout, bb_timeout;
+ int ret = 0;
+
+ if (i2c->is_suspended)
+ return -EBUSY;
+
+ synquacer_i2c_hw_init(i2c);
+ bsr = readb(i2c->base + SYNQUACER_I2C_REG_BSR);
+ if (bsr & SYNQUACER_I2C_BSR_BB) {
+ dev_err(i2c->dev, "cannot get bus (bus busy)\n");
+ return -EBUSY;
+ }
+
+ init_completion(&i2c->completion);
+
+ i2c->msg = msgs;
+ i2c->msg_num = num;
+ i2c->msg_ptr = 0;
+ i2c->msg_idx = 0;
+ i2c->state = STATE_START;
+
+ ret = synquacer_i2c_master_start(i2c, i2c->msg);
+ if (ret < 0) {
+ dev_dbg(i2c->dev, "Address failed: (0x%08x)\n", ret);
+ goto out;
+ }
+
+ timeout = wait_for_completion_timeout(&i2c->completion,
+ SYNQUACER_I2C_TIMEOUT(i2c->timeout_ms));
+ if (timeout <= 0) {
+ dev_dbg(i2c->dev, "timeout\n");
+ ret = -EAGAIN;
+ goto out;
+ }
+
+ ret = i2c->msg_idx;
+ if (ret != num) {
+ dev_dbg(i2c->dev, "incomplete xfer (%d)\n", ret);
+ ret = -EAGAIN;
+ goto out;
+ }
+
+ /* ensure the stop has been through the bus */
+ bb_timeout = jiffies + HZ;
+ do {
+ bsr = readb(i2c->base + SYNQUACER_I2C_REG_BSR);
+ } while ((bsr & SYNQUACER_I2C_BSR_BB) &&
+ time_before(jiffies, bb_timeout));
+out:
+ return ret;
+}
+
+static irqreturn_t synquacer_i2c_isr(int irq, void *dev_id)
+{
+ struct synquacer_i2c *i2c = dev_id;
+
+ unsigned char byte;
+ unsigned char bsr, bcr;
+ int ret = 0;
+
+ bcr = readb(i2c->base + SYNQUACER_I2C_REG_BCR);
+ bsr = readb(i2c->base + SYNQUACER_I2C_REG_BSR);
+ dev_dbg(i2c->dev, "%s bsr:0x%02x, bcr:0x%02x\n", __func__,
+ bsr, bcr);
+
+ if (bcr & SYNQUACER_I2C_BCR_BER) {
+ dev_err(i2c->dev, "%s: bus error\n", __func__);
+ synquacer_i2c_stop(i2c, -EAGAIN);
+ goto out;
+ }
+ if ((bsr & SYNQUACER_I2C_BSR_AL) ||
+ !(bcr & SYNQUACER_I2C_BCR_MSS)) {
+ dev_dbg(i2c->dev, "%s arbitration lost\n", __func__);
+ synquacer_i2c_stop(i2c, -EAGAIN);
+ goto out;
+ }
+
+ switch (i2c->state) {
+
+ case STATE_START:
+ if (bsr & SYNQUACER_I2C_BSR_LRB) {
+ dev_dbg(i2c->dev, "ack was not received\n");
+ synquacer_i2c_stop(i2c, -EAGAIN);
+ goto out;
+ }
+
+ if (i2c->msg->flags & I2C_M_RD)
+ i2c->state = STATE_READ;
+ else
+ i2c->state = STATE_WRITE;
+
+ if (is_lastmsg(i2c) && i2c->msg->len == 0) {
+ synquacer_i2c_stop(i2c, 0);
+ goto out;
+ }
+
+ if (i2c->state == STATE_READ)
+ goto prepare_read;
+
+ /* fallthru */
+
+ case STATE_WRITE:
+ if (bsr & SYNQUACER_I2C_BSR_LRB) {
+ dev_dbg(i2c->dev, "WRITE: No Ack\n");
+ synquacer_i2c_stop(i2c, -EAGAIN);
+ goto out;
+ }
+
+ if (!is_msgend(i2c)) {
+ writeb(i2c->msg->buf[i2c->msg_ptr++],
+ i2c->base + SYNQUACER_I2C_REG_DAR);
+
+ /* clear IRQ, and continue */
+ writeb(SYNQUACER_I2C_BCR_BEIE |
+ SYNQUACER_I2C_BCR_MSS |
+ SYNQUACER_I2C_BCR_INTE,
+ i2c->base + SYNQUACER_I2C_REG_BCR);
+ break;
+ }
+ if (is_lastmsg(i2c)) {
+ synquacer_i2c_stop(i2c, 0);
+ break;
+ }
+ dev_dbg(i2c->dev, "WRITE: Next Message\n");
+
+ i2c->msg_ptr = 0;
+ i2c->msg_idx++;
+ i2c->msg++;
+
+ /* send the new start */
+ ret = synquacer_i2c_master_start(i2c, i2c->msg);
+ if (ret < 0) {
+ dev_dbg(i2c->dev, "restart err:0x%08x\n", ret);
+ synquacer_i2c_stop(i2c, -EAGAIN);
+ break;
+ }
+ i2c->state = STATE_START;
+ break;
+
+ case STATE_READ:
+ if (!(bsr & SYNQUACER_I2C_BSR_FBT)) { /* data */
+ byte = readb(i2c->base + SYNQUACER_I2C_REG_DAR);
+ i2c->msg->buf[i2c->msg_ptr++] = byte;
+ } else /* address */
+ dev_dbg(i2c->dev, ", address:0x%08x. ignore it.\n",
+ readb(i2c->base + SYNQUACER_I2C_REG_DAR));
+
+prepare_read:
+ if (is_msglast(i2c)) {
+ writeb(SYNQUACER_I2C_BCR_MSS |
+ SYNQUACER_I2C_BCR_BEIE |
+ SYNQUACER_I2C_BCR_INTE,
+ i2c->base + SYNQUACER_I2C_REG_BCR);
+ break;
+ }
+ if (!is_msgend(i2c)) {
+ writeb(SYNQUACER_I2C_BCR_MSS |
+ SYNQUACER_I2C_BCR_BEIE |
+ SYNQUACER_I2C_BCR_INTE |
+ SYNQUACER_I2C_BCR_ACK,
+ i2c->base + SYNQUACER_I2C_REG_BCR);
+ break;
+ }
+ if (is_lastmsg(i2c)) {
+ /* last message, send stop and complete */
+ dev_dbg(i2c->dev, "READ: Send Stop\n");
+ synquacer_i2c_stop(i2c, 0);
+ break;
+ }
+ dev_dbg(i2c->dev, "READ: Next Transfer\n");
+
+ i2c->msg_ptr = 0;
+ i2c->msg_idx++;
+ i2c->msg++;
+
+ ret = synquacer_i2c_master_start(i2c, i2c->msg);
+ if (ret < 0) {
+ dev_dbg(i2c->dev, "restart err: 0x%08x\n", ret);
+ synquacer_i2c_stop(i2c, -EAGAIN);
+ } else
+ i2c->state = STATE_START;
+ break;
+ default:
+ dev_err(i2c->dev, "%s: called in err STATE (%d)\n",
+ __func__, i2c->state);
+ break;
+ }
+
+out:
+ WAIT_PCLK(10, i2c->clkrate);
+ return IRQ_HANDLED;
+}
+
+static int synquacer_i2c_xfer(struct i2c_adapter *adap,
+ struct i2c_msg *msgs, int num)
+{
+ struct synquacer_i2c *i2c;
+ int retry;
+ int ret = 0;
+
+ if (!msgs)
+ return -EINVAL;
+ if (num <= 0)
+ return -EINVAL;
+
+ i2c = i2c_get_adapdata(adap);
+ i2c->timeout_ms = calc_timeout_ms(i2c, msgs, num);
+
+ dev_dbg(i2c->dev, "calculated timeout %d ms\n",
+ i2c->timeout_ms);
+
+ for (retry = 0; retry < adap->retries; retry++) {
+
+ ret = synquacer_i2c_doxfer(i2c, msgs, num);
+ if (ret != -EAGAIN)
+ return ret;
+
+ dev_dbg(i2c->dev, "Retrying transmission (%d)\n",
+ retry);
+
+ synquacer_i2c_master_recover(i2c);
+ synquacer_i2c_hw_reset(i2c);
+ }
+ return -EIO;
+}
+
+static u32 synquacer_i2c_functionality(struct i2c_adapter *adap)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static const struct i2c_algorithm synquacer_i2c_algo = {
+ .master_xfer = synquacer_i2c_xfer,
+ .functionality = synquacer_i2c_functionality,
+};
+
+static struct i2c_adapter synquacer_i2c_ops = {
+ .owner = THIS_MODULE,
+ .name = "synquacer_i2c-adapter",
+ .algo = &synquacer_i2c_algo,
+ .retries = 5,
+};
+
+static int synquacer_i2c_probe(struct platform_device *pdev)
+{
+ struct synquacer_i2c *i2c;
+ struct resource *r;
+ int speed_khz;
+ int ret;
+
+ ret = device_property_read_u32(&pdev->dev, "clock-frequency",
+ &speed_khz);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "Missing clock-frequency property\n");
+ return -EINVAL;
+ }
+ speed_khz /= 1000;
+
+ i2c = devm_kzalloc(&pdev->dev, sizeof(*i2c), GFP_KERNEL);
+ if (!i2c)
+ return -ENOMEM;
+
+ if (dev_of_node(&pdev->dev)) {
+ i2c->clk = devm_clk_get(&pdev->dev, "pclk");
+ if (IS_ERR(i2c->clk)) {
+ dev_err(&pdev->dev, "cannot get clock\n");
+ return PTR_ERR(i2c->clk);
+ }
+ dev_dbg(&pdev->dev, "clock source %p\n", i2c->clk);
+
+ i2c->clkrate = clk_get_rate(i2c->clk);
+ dev_dbg(&pdev->dev, "clock rate %d\n", i2c->clkrate);
+ clk_prepare_enable(i2c->clk);
+ } else {
+ ret = device_property_read_u32(&pdev->dev,
+ "socionext,pclk-rate",
+ &i2c->clkrate);
+ if (ret)
+ return ret;
+ }
+
+ if (i2c->clkrate < SYNQUACER_I2C_MIN_CLK_RATE ||
+ i2c->clkrate > SYNQUACER_I2C_MAX_CLK_RATE) {
+ dev_err(&pdev->dev, "PCLK rate out of range (%d)\n",
+ i2c->clkrate);
+ return -EINVAL;
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ i2c->base = devm_ioremap_resource(&pdev->dev, r);
+ if (IS_ERR(i2c->base))
+ return PTR_ERR(i2c->base);
+
+ dev_dbg(&pdev->dev, "registers %p (%p)\n", i2c->base, r);
+
+ i2c->irq = platform_get_irq(pdev, 0);
+ if (i2c->irq <= 0) {
+ dev_err(&pdev->dev, "no IRQ resource found\n");
+ return -ENODEV;
+ }
+
+ ret = devm_request_irq(&pdev->dev, i2c->irq, synquacer_i2c_isr,
+ 0, dev_name(&pdev->dev), i2c);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "cannot claim IRQ %d\n", i2c->irq);
+ return ret;
+ }
+
+ i2c->state = STATE_IDLE;
+ i2c->dev = &pdev->dev;
+ i2c->msg = NULL;
+ i2c->speed_khz = SYNQUACER_I2C_SPEED_SM;
+ if (speed_khz == SYNQUACER_I2C_SPEED_FM)
+ i2c->speed_khz = SYNQUACER_I2C_SPEED_FM;
+
+ synquacer_i2c_hw_init(i2c);
+
+ i2c->adapter = synquacer_i2c_ops;
+ i2c_set_adapdata(&i2c->adapter, i2c);
+ i2c->adapter.dev.parent = &pdev->dev;
+ i2c->adapter.nr = pdev->id;
+
+ ret = i2c_add_numbered_adapter(&i2c->adapter);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to add bus to i2c core\n");
+ return ret;
+ }
+
+ platform_set_drvdata(pdev, i2c);
+
+ dev_info(&pdev->dev, "%s: synquacer_i2c adapter\n",
+ dev_name(&i2c->adapter.dev));
+
+ return 0;
+}
+
+static int synquacer_i2c_remove(struct platform_device *pdev)
+{
+ struct synquacer_i2c *i2c = platform_get_drvdata(pdev);
+
+ platform_set_drvdata(pdev, NULL);
+ i2c_del_adapter(&i2c->adapter);
+ clk_disable_unprepare(i2c->clk);
+
+ return 0;
+};
+
+#ifdef CONFIG_PM_SLEEP
+static int synquacer_i2c_suspend(struct device *dev)
+{
+ struct synquacer_i2c *i2c = dev_get_drvdata(dev);
+
+ i2c_lock_adapter(&i2c->adapter);
+ i2c->is_suspended = true;
+ i2c_unlock_adapter(&i2c->adapter);
+
+ clk_disable_unprepare(i2c->clk);
+
+ return 0;
+}
+
+static int synquacer_i2c_resume(struct device *dev)
+{
+ struct synquacer_i2c *i2c = dev_get_drvdata(dev);
+ int ret;
+
+ i2c_lock_adapter(&i2c->adapter);
+
+ ret = clk_prepare_enable(i2c->clk);
+
+ if (!ret)
+ i2c->is_suspended = false;
+
+ i2c_unlock_adapter(&i2c->adapter);
+
+ return ret;
+}
+
+static SIMPLE_DEV_PM_OPS(synquacer_i2c_pm, synquacer_i2c_suspend,
+ synquacer_i2c_resume);
+#define SYNQUACER_I2C_PM (&synquacer_i2c_pm)
+#else
+#define SYNQUACER_I2C_PM NULL
+#endif
+
+#ifdef CONFIG_OF
+static const struct of_device_id synquacer_i2c_dt_ids[] = {
+ { .compatible = "socionext,synquacer-i2c" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, synquacer_i2c_dt_ids);
+#endif
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id synquacer_i2c_acpi_ids[] = {
+ { "SCX0003" },
+ { /* sentinel */ }
+};
+#endif
+
+static struct platform_driver synquacer_i2c_driver = {
+ .probe = synquacer_i2c_probe,
+ .remove = synquacer_i2c_remove,
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "synquacer_i2c",
+ .of_match_table = of_match_ptr(synquacer_i2c_dt_ids),
+ .acpi_match_table = ACPI_PTR(synquacer_i2c_acpi_ids),
+ .pm = SYNQUACER_I2C_PM,
+ },
+};
+module_platform_driver(synquacer_i2c_driver);
+
+MODULE_AUTHOR("Fujitsu Semiconductor Ltd");
+MODULE_DESCRIPTION("Socionext SynQuacer I2C Driver");
+MODULE_LICENSE("GPL v2");
This is a cleaned up version of the I2C controller driver for the Fujitsu F_I2C IP, which was never supported upstream, and has now been incorporated into the Socionext SynQuacer SoC. Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> --- drivers/i2c/busses/Kconfig | 11 + drivers/i2c/busses/Makefile | 1 + drivers/i2c/busses/i2c-synquacer.c | 817 ++++++++++++++++++++ 3 files changed, 829 insertions(+)