| Message ID | 1310966402-12318-1-git-send-email-tony.lin@freescale.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Does anybody have any comment? Anybody tried this patch? BR Tony > -----Original Message----- > From: linux-arm-kernel-bounces@lists.infradead.org [mailto:linux-arm- > kernel-bounces@lists.infradead.org] On Behalf Of Tony Lin > Sent: Monday, July 18, 2011 1:20 PM > To: linux-mmc@vger.kernel.org > Cc: cjb@laptop.org; linux-arm-kernel@lists.infradead.org > Subject: [PATCH 1/1] fix card interrupt losing issue on freescale eSDHC > > apply workaround for imx eSDHC controller to avoid missing card interrupt > so that SDIO function is workable > > Signed-off-by: Tony Lin <tony.lin@freescale.com> > --- > drivers/mmc/host/sdhci-esdhc-imx.c | 39 +++++++++++++++++++++++++++--- > ----- > 1 files changed, 30 insertions(+), 9 deletions(-) > > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci- > esdhc-imx.c > index a19967d..da77cae 100644 > --- a/drivers/mmc/host/sdhci-esdhc-imx.c > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c > @@ -32,6 +32,8 @@ > #define SDHCI_VENDOR_SPEC_SDIO_QUIRK 0x00000002 > > #define ESDHC_FLAG_GPIO_FOR_CD_WP (1 << 0) > + > +#define SDHCI_CTRL_D3CD 0x08 > /* > * The CMDTYPE of the CMD register (offset 0xE) should be set to > * "11" when the STOP CMD12 is issued on imx53 to abort one @@ -87,14 > +89,31 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, > int reg) { > struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > struct pltfm_imx_data *imx_data = pltfm_host->priv; > - > - if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE) > - && (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP))) > - /* > - * these interrupts won't work with a custom card_detect gpio > - * (only applied to mx25/35) > - */ > - val &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT); > + u32 data; > + > + if (unlikely((reg == SDHCI_INT_ENABLE || reg == > SDHCI_SIGNAL_ENABLE))) { > + if (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP) > + /* > + * these interrupts won't work with a custom > + * card_detect gpio (only applied to mx25/35) > + */ > + val &= ~(SDHCI_INT_CARD_REMOVE | \ > + SDHCI_INT_CARD_INSERT); > + > + if (val & SDHCI_INT_CARD_INT) { > + /* > + * clear D3CD bit and set D3CD bit to avoid > + * missing card interrupt > + * this is a eSDHC controller problem so that > + * we need to apply following workaround > + */ > + data = readl(host->ioaddr + SDHCI_HOST_CONTROL); > + data &= ~SDHCI_CTRL_D3CD; > + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); > + data |= SDHCI_CTRL_D3CD; > + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); > + } > + } > > if (unlikely((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT) > && (reg == SDHCI_INT_STATUS) > @@ -165,7 +184,9 @@ static void esdhc_writeb_le(struct sdhci_host *host, > u8 val, int reg) > return; > case SDHCI_HOST_CONTROL: > /* FSL messed up here, so we can just keep those two */ > - new_val = val & (SDHCI_CTRL_LED | SDHCI_CTRL_4BITBUS); > + new_val = val & (SDHCI_CTRL_LED | \ > + SDHCI_CTRL_4BITBUS | \ > + SDHCI_CTRL_D3CD); > /* ensure the endianess */ > new_val |= ESDHC_HOST_CONTROL_LE; > /* DMA mode bits are shifted */ > -- > 1.7.0.4 > > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello Tony, On Mon, Jul 18, 2011 at 01:20:02PM +0800, Tony Lin wrote: > apply workaround for imx eSDHC controller to avoid > missing card interrupt so that SDIO function is workable Fixing a few typos (but note, I'm not a native speaker): mmc/sdhci-esdhc-imx: fix losing card interrupt Apply workaround for the imx eSDHC controller to avoid missing a card interrupt. Signed-off-by: ... > Signed-off-by: Tony Lin <tony.lin@freescale.com> > --- > drivers/mmc/host/sdhci-esdhc-imx.c | 39 +++++++++++++++++++++++++++-------- > 1 files changed, 30 insertions(+), 9 deletions(-) > > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c > index a19967d..da77cae 100644 > --- a/drivers/mmc/host/sdhci-esdhc-imx.c > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c > @@ -32,6 +32,8 @@ > #define SDHCI_VENDOR_SPEC_SDIO_QUIRK 0x00000002 > > #define ESDHC_FLAG_GPIO_FOR_CD_WP (1 << 0) > + > +#define SDHCI_CTRL_D3CD 0x08 > /* > * The CMDTYPE of the CMD register (offset 0xE) should be set to > * "11" when the STOP CMD12 is issued on imx53 to abort one > @@ -87,14 +89,31 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg) > { > struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > struct pltfm_imx_data *imx_data = pltfm_host->priv; > - > - if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE) > - && (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP))) > - /* > - * these interrupts won't work with a custom card_detect gpio > - * (only applied to mx25/35) > - */ > - val &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT); > + u32 data; > + > + if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE))) { > + if (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP) > + /* > + * these interrupts won't work with a custom > + * card_detect gpio (only applied to mx25/35) hmm, ok, this was here before, but I wonder about the "only applied to mx25/35" part. How is that meant? I don't see logic to prevent other socs using this workaround. > + */ > + val &= ~(SDHCI_INT_CARD_REMOVE | \ > + SDHCI_INT_CARD_INSERT); > + > + if (val & SDHCI_INT_CARD_INT) { > + /* > + * clear D3CD bit and set D3CD bit to avoid > + * missing card interrupt > + * this is a eSDHC controller problem so that > + * we need to apply following workaround s/following/this/ ? If not, according to my (non-native) English you need to add a "the" before "following". > + */ > + data = readl(host->ioaddr + SDHCI_HOST_CONTROL); > + data &= ~SDHCI_CTRL_D3CD; > + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); > + data |= SDHCI_CTRL_D3CD; > + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); Is there some Documentation about this problem? If yes, maybe add a link to it? Alternatively describe the problem more exact in a comment please. > + } > + } > > if (unlikely((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT) > && (reg == SDHCI_INT_STATUS) > @@ -165,7 +184,9 @@ static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg) > return; > case SDHCI_HOST_CONTROL: > /* FSL messed up here, so we can just keep those two */ > - new_val = val & (SDHCI_CTRL_LED | SDHCI_CTRL_4BITBUS); > + new_val = val & (SDHCI_CTRL_LED | \ > + SDHCI_CTRL_4BITBUS | \ > + SDHCI_CTRL_D3CD); This makes the comment wrong---now there are three bits that can be preserved. Best regards Uwe
> -----Original Message----- > From: linux-arm-kernel-bounces@lists.infradead.org [mailto:linux-arm- > kernel-bounces@lists.infradead.org] On Behalf Of Uwe Kleine-K?nig > Sent: Wednesday, July 27, 2011 3:47 PM > To: Lin Tony-B19295 > Cc: cjb@laptop.org; linux-mmc@vger.kernel.org; kernel@pengutronix.de; > linux-arm-kernel@lists.infradead.org > Subject: Re: [PATCH 1/1] fix card interrupt losing issue on freescale > eSDHC > > Hello Tony, > > On Mon, Jul 18, 2011 at 01:20:02PM +0800, Tony Lin wrote: > > apply workaround for imx eSDHC controller to avoid missing card > > interrupt so that SDIO function is workable > Fixing a few typos (but note, I'm not a native speaker): > > mmc/sdhci-esdhc-imx: fix losing card interrupt > > Apply workaround for the imx eSDHC controller to avoid missing a > card interrupt. > > Signed-off-by: ... > > > Signed-off-by: Tony Lin <tony.lin@freescale.com> > > --- > > drivers/mmc/host/sdhci-esdhc-imx.c | 39 +++++++++++++++++++++++++++- > ------- > > 1 files changed, 30 insertions(+), 9 deletions(-) > > > > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c > > b/drivers/mmc/host/sdhci-esdhc-imx.c > > index a19967d..da77cae 100644 > > --- a/drivers/mmc/host/sdhci-esdhc-imx.c > > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c > > @@ -32,6 +32,8 @@ > > #define SDHCI_VENDOR_SPEC_SDIO_QUIRK 0x00000002 > > > > #define ESDHC_FLAG_GPIO_FOR_CD_WP (1 << 0) > > + > > +#define SDHCI_CTRL_D3CD 0x08 > > /* > > * The CMDTYPE of the CMD register (offset 0xE) should be set to > > * "11" when the STOP CMD12 is issued on imx53 to abort one @@ -87,14 > > +89,31 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 > > val, int reg) { > > struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); > > struct pltfm_imx_data *imx_data = pltfm_host->priv; > > - > > - if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE) > > - && (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP))) > > - /* > > - * these interrupts won't work with a custom card_detect gpio > > - * (only applied to mx25/35) > > - */ > > - val &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT); > > + u32 data; > > + > > + if (unlikely((reg == SDHCI_INT_ENABLE || reg == > SDHCI_SIGNAL_ENABLE))) { > > + if (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP) > > + /* > > + * these interrupts won't work with a custom > > + * card_detect gpio (only applied to mx25/35) > hmm, ok, this was here before, but I wonder about the "only applied to > mx25/35" part. How is that meant? I don't see logic to prevent other socs > using this workaround. Sorry, not so sure about mx25/35 history. But the flag is set only if it's mx25 or mx35. You can check the code in esdhc_pltfm_init. > > > + */ > > + val &= ~(SDHCI_INT_CARD_REMOVE | \ > > + SDHCI_INT_CARD_INSERT); > > + > > + if (val & SDHCI_INT_CARD_INT) { > > + /* > > + * clear D3CD bit and set D3CD bit to avoid > > + * missing card interrupt > > + * this is a eSDHC controller problem so that > > + * we need to apply following workaround > s/following/this/ ? If not, according to my (non-native) English you need > to add a "the" before "following". > > > + */ > > + data = readl(host->ioaddr + SDHCI_HOST_CONTROL); > > + data &= ~SDHCI_CTRL_D3CD; > > + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); > > + data |= SDHCI_CTRL_D3CD; > > + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); > Is there some Documentation about this problem? If yes, maybe add a link > to it? Alternatively describe the problem more exact in a comment please. > > > + } > > + } > > > > if (unlikely((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT) > > && (reg == SDHCI_INT_STATUS) > > @@ -165,7 +184,9 @@ static void esdhc_writeb_le(struct sdhci_host *host, > u8 val, int reg) > > return; > > case SDHCI_HOST_CONTROL: > > /* FSL messed up here, so we can just keep those two */ > > - new_val = val & (SDHCI_CTRL_LED | SDHCI_CTRL_4BITBUS); > > + new_val = val & (SDHCI_CTRL_LED | \ > > + SDHCI_CTRL_4BITBUS | \ > > + SDHCI_CTRL_D3CD); > This makes the comment wrong---now there are three bits that can be > preserved. > Thanks for your comments. Accepted. > Best regards > Uwe > > -- > Pengutronix e.K. | Uwe Kleine-König > | > Industrial Linux Solutions | http://www.pengutronix.de/ > | > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Lin Tony-B19295 <B19295@freescale.com> writes: Hi, >> -----Original Message----- >> From: linux-arm-kernel-bounces@lists.infradead.org [mailto:linux-arm- >> kernel-bounces@lists.infradead.org] On Behalf Of Uwe Kleine-K?nig >> Sent: Wednesday, July 27, 2011 3:47 PM >> To: Lin Tony-B19295 >> Cc: cjb@laptop.org; linux-mmc@vger.kernel.org; kernel@pengutronix.de; >> linux-arm-kernel@lists.infradead.org >> Subject: Re: [PATCH 1/1] fix card interrupt losing issue on freescale >> eSDHC >> >> Hello Tony, >> >> On Mon, Jul 18, 2011 at 01:20:02PM +0800, Tony Lin wrote: >> > apply workaround for imx eSDHC controller to avoid missing card >> > interrupt so that SDIO function is workable >> Fixing a few typos (but note, I'm not a native speaker): >> >> mmc/sdhci-esdhc-imx: fix losing card interrupt >> >> Apply workaround for the imx eSDHC controller to avoid missing a >> card interrupt. >> >> Signed-off-by: ... >> >> > Signed-off-by: Tony Lin <tony.lin@freescale.com> >> > --- >> > drivers/mmc/host/sdhci-esdhc-imx.c | 39 +++++++++++++++++++++++++++- >> ------- >> > 1 files changed, 30 insertions(+), 9 deletions(-) >> > >> > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c >> > b/drivers/mmc/host/sdhci-esdhc-imx.c >> > index a19967d..da77cae 100644 >> > --- a/drivers/mmc/host/sdhci-esdhc-imx.c >> > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c >> > @@ -32,6 +32,8 @@ >> > #define SDHCI_VENDOR_SPEC_SDIO_QUIRK 0x00000002 >> > >> > #define ESDHC_FLAG_GPIO_FOR_CD_WP (1 << 0) >> > + >> > +#define SDHCI_CTRL_D3CD 0x08 >> > /* >> > * The CMDTYPE of the CMD register (offset 0xE) should be set to >> > * "11" when the STOP CMD12 is issued on imx53 to abort one @@ -87,14 >> > +89,31 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 >> > val, int reg) { >> > struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); >> > struct pltfm_imx_data *imx_data = pltfm_host->priv; >> > - >> > - if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE) >> > - && (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP))) >> > - /* >> > - * these interrupts won't work with a custom card_detect gpio >> > - * (only applied to mx25/35) >> > - */ >> > - val &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT); >> > + u32 data; >> > + >> > + if (unlikely((reg == SDHCI_INT_ENABLE || reg == >> SDHCI_SIGNAL_ENABLE))) { >> > + if (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP) >> > + /* >> > + * these interrupts won't work with a custom >> > + * card_detect gpio (only applied to mx25/35) >> hmm, ok, this was here before, but I wonder about the "only applied to >> mx25/35" part. How is that meant? I don't see logic to prevent other socs >> using this workaround. > Sorry, not so sure about mx25/35 history. But the flag is set only if it's mx25 or mx35. > You can check the code in esdhc_pltfm_init. btw, I didn't notice when looking at the patch but this flag has been renamed and maybe will be gone. See : - latest commits on this file on mmc for-next: http://git.kernel.org/?p=linux/kernel/git/cjb/mmc.git;a=commitdiff;h=e8cd77e467f7bb1d4b942037c47b087334a484d4 - last patch of the imx mmc fixes for cd/wp: http://lists.infradead.org/pipermail/linux-arm-kernel/2011-June/052743.html So, imho, it would be better to use an other way to check for mx25/35 as current one won't work (at least won't compile but won't work as intended if the last patch mentionned is merged. There are other systems using gpio for cd or wp which are not mx25/35). Arnaud -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c index a19967d..da77cae 100644 --- a/drivers/mmc/host/sdhci-esdhc-imx.c +++ b/drivers/mmc/host/sdhci-esdhc-imx.c @@ -32,6 +32,8 @@ #define SDHCI_VENDOR_SPEC_SDIO_QUIRK 0x00000002 #define ESDHC_FLAG_GPIO_FOR_CD_WP (1 << 0) + +#define SDHCI_CTRL_D3CD 0x08 /* * The CMDTYPE of the CMD register (offset 0xE) should be set to * "11" when the STOP CMD12 is issued on imx53 to abort one @@ -87,14 +89,31 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg) { struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct pltfm_imx_data *imx_data = pltfm_host->priv; - - if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE) - && (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP))) - /* - * these interrupts won't work with a custom card_detect gpio - * (only applied to mx25/35) - */ - val &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT); + u32 data; + + if (unlikely((reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE))) { + if (imx_data->flags & ESDHC_FLAG_GPIO_FOR_CD_WP) + /* + * these interrupts won't work with a custom + * card_detect gpio (only applied to mx25/35) + */ + val &= ~(SDHCI_INT_CARD_REMOVE | \ + SDHCI_INT_CARD_INSERT); + + if (val & SDHCI_INT_CARD_INT) { + /* + * clear D3CD bit and set D3CD bit to avoid + * missing card interrupt + * this is a eSDHC controller problem so that + * we need to apply following workaround + */ + data = readl(host->ioaddr + SDHCI_HOST_CONTROL); + data &= ~SDHCI_CTRL_D3CD; + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); + data |= SDHCI_CTRL_D3CD; + writel(data, host->ioaddr + SDHCI_HOST_CONTROL); + } + } if (unlikely((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT) && (reg == SDHCI_INT_STATUS) @@ -165,7 +184,9 @@ static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg) return; case SDHCI_HOST_CONTROL: /* FSL messed up here, so we can just keep those two */ - new_val = val & (SDHCI_CTRL_LED | SDHCI_CTRL_4BITBUS); + new_val = val & (SDHCI_CTRL_LED | \ + SDHCI_CTRL_4BITBUS | \ + SDHCI_CTRL_D3CD); /* ensure the endianess */ new_val |= ESDHC_HOST_CONTROL_LE; /* DMA mode bits are shifted */
apply workaround for imx eSDHC controller to avoid missing card interrupt so that SDIO function is workable Signed-off-by: Tony Lin <tony.lin@freescale.com> --- drivers/mmc/host/sdhci-esdhc-imx.c | 39 +++++++++++++++++++++++++++-------- 1 files changed, 30 insertions(+), 9 deletions(-)