| Message ID | 1528813566-17927-7-git-send-email-jacopo+renesas@jmondi.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Jacopo, On Tue, Jun 12, 2018 at 04:26:06PM +0200, Jacopo Mondi wrote: > Add a note to the R-Car VIN interface bindings to clarify that all > properties listed as generic properties in video-interfaces.txt can > be included in port@0 endpoint, but if not explicitly listed in the > interface bindings documentation, they do not modify it behaviour. > > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > --- > Documentation/devicetree/bindings/media/rcar_vin.txt | 6 ++++++ > 1 file changed, 6 insertions(+) > > diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt > index 8130849..03544c7 100644 > --- a/Documentation/devicetree/bindings/media/rcar_vin.txt > +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt > @@ -55,6 +55,12 @@ from local SoC CSI-2 receivers (port1) depending on SoC. > instances that are connected to external pins should have port 0. > > - Optional properties for endpoint nodes of port@0: > + > + All properties described in [1] and which apply to the selected > + media bus type could be optionally listed here to better describe > + the current hardware configuration, but only the following ones do > + actually modify the VIN interface behaviour: > + I don't think this should be needed. You should only have properties that describe the hardware configuration in a given system. > - hsync-active: see [1] for description. Default is active high. > - vsync-active: see [1] for description. Default is active high. > - data-enable-active: polarity of CLKENB signal, see [1] for > -- > 2.7.4 >
Hello, On Tuesday, 12 June 2018 18:45:53 EEST Sakari Ailus wrote: > On Tue, Jun 12, 2018 at 04:26:06PM +0200, Jacopo Mondi wrote: > > Add a note to the R-Car VIN interface bindings to clarify that all > > properties listed as generic properties in video-interfaces.txt can > > be included in port@0 endpoint, but if not explicitly listed in the > > interface bindings documentation, they do not modify it behaviour. > > > > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > > --- > > > > Documentation/devicetree/bindings/media/rcar_vin.txt | 6 ++++++ > > 1 file changed, 6 insertions(+) > > > > diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt > > b/Documentation/devicetree/bindings/media/rcar_vin.txt index > > 8130849..03544c7 100644 > > --- a/Documentation/devicetree/bindings/media/rcar_vin.txt > > +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt > > @@ -55,6 +55,12 @@ from local SoC CSI-2 receivers (port1) depending on > > SoC. > > > > instances that are connected to external pins should have port 0. > > > > - Optional properties for endpoint nodes of port@0: > > + > > + All properties described in [1] and which apply to the selected > > + media bus type could be optionally listed here to better describe > > + the current hardware configuration, but only the following ones > > do > > + actually modify the VIN interface behaviour: > > + > > I don't think this should be needed. You should only have properties that > describe the hardware configuration in a given system. I agree. Please list explicitly all properties that are applicable for this device, and don't tell which one(s) are used by the driver. > > - hsync-active: see [1] for description. Default is active high. > > - vsync-active: see [1] for description. Default is active high. > > - data-enable-active: polarity of CLKENB signal, see [1] for
Hi Sakari, On Tue, Jun 12, 2018 at 06:45:53PM +0300, Sakari Ailus wrote: > Hi Jacopo, > > On Tue, Jun 12, 2018 at 04:26:06PM +0200, Jacopo Mondi wrote: > > Add a note to the R-Car VIN interface bindings to clarify that all > > properties listed as generic properties in video-interfaces.txt can > > be included in port@0 endpoint, but if not explicitly listed in the > > interface bindings documentation, they do not modify it behaviour. > > > > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > > --- > > Documentation/devicetree/bindings/media/rcar_vin.txt | 6 ++++++ > > 1 file changed, 6 insertions(+) > > > > diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt > > index 8130849..03544c7 100644 > > --- a/Documentation/devicetree/bindings/media/rcar_vin.txt > > +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt > > @@ -55,6 +55,12 @@ from local SoC CSI-2 receivers (port1) depending on SoC. > > instances that are connected to external pins should have port 0. > > > > - Optional properties for endpoint nodes of port@0: > > + > > + All properties described in [1] and which apply to the selected > > + media bus type could be optionally listed here to better describe > > + the current hardware configuration, but only the following ones do > > + actually modify the VIN interface behaviour: > > + > > I don't think this should be needed. You should only have properties that > describe the hardware configuration in a given system. > There has been quite some debate on this, and please bear with me here for re-proposing it: I started by removing properties in some DT files for older Renesas board which listed endpoint properties not documented in the VIN's bindings and not parsed by the VIN driver [1] Niklas (but Simon and Geert seems to agree here) opposed to that patch, as those properties where described in 'video-interfaces.txt' and even if not parsed by the current driver implementation, they actually describe hardware. I rebated that only properties listed in the device bindings documentation should actually be used, and having properties not parsed by the driver confuses users, which may expect changing them modifies the interface configuration, which does not happens at the moment. This came out as a middle ground from a discussion with Niklas. As stated in the cover letter if this patch makes someone uncomfortable, feel free to drop it not to hold back the rest of the series which has been well received instead. Thanks j [1] https://www.spinics.net/lists/arm-kernel/msg656302.html > > - hsync-active: see [1] for description. Default is active high. > > - vsync-active: see [1] for description. Default is active high. > > - data-enable-active: polarity of CLKENB signal, see [1] for > > -- > > 2.7.4 > > > > -- > Sakari Ailus > sakari.ailus@linux.intel.com
Hi Jacopo, Sakari and Laurent, Jacopo, thanks for your patch and continued work on resolving this. On 2018-06-13 10:54:55 +0200, Jacopo Mondi wrote: > Hi Sakari, > > On Tue, Jun 12, 2018 at 06:45:53PM +0300, Sakari Ailus wrote: > > Hi Jacopo, > > > > On Tue, Jun 12, 2018 at 04:26:06PM +0200, Jacopo Mondi wrote: > > > Add a note to the R-Car VIN interface bindings to clarify that all > > > properties listed as generic properties in video-interfaces.txt can > > > be included in port@0 endpoint, but if not explicitly listed in the > > > interface bindings documentation, they do not modify it behaviour. > > > > > > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > > > --- > > > Documentation/devicetree/bindings/media/rcar_vin.txt | 6 ++++++ > > > 1 file changed, 6 insertions(+) > > > > > > diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt > > > index 8130849..03544c7 100644 > > > --- a/Documentation/devicetree/bindings/media/rcar_vin.txt > > > +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt > > > @@ -55,6 +55,12 @@ from local SoC CSI-2 receivers (port1) depending on SoC. > > > instances that are connected to external pins should have port 0. > > > > > > - Optional properties for endpoint nodes of port@0: > > > + > > > + All properties described in [1] and which apply to the selected > > > + media bus type could be optionally listed here to better describe > > > + the current hardware configuration, but only the following ones do > > > + actually modify the VIN interface behaviour: > > > + I'm not sure the description have to be as explicit to that the properties in 'video-interfaces.txt' are not currently used by the driver. I find it not relevant which ones are used or not, what is important for me is that all properties in 'video-interfaces.txt' which can be used to describe the specific bus are valid for the DT description. On a side note, in rcar_vin.txt we have this section describing the Gen2 bindings: The per-board settings Gen2 platforms: - port sub-node describing a single endpoint connected to the vin as described in video-interfaces.txt[1]. Only the first one will be considered as each vin interface has one input port. This whole series only deals with documenting the Gen3 optional properties and not the Gen2. Maybe with parallel input support for Gen3 patches on there way to making it upstream this series should be extended to in a good way merge the port@0 optional properties for both generations of hardware? > > > > I don't think this should be needed. You should only have properties that > > describe the hardware configuration in a given system. > > > > There has been quite some debate on this, and please bear with me > here for re-proposing it: I started by removing properties in some DT > files for older Renesas board which listed endpoint properties not > documented in the VIN's bindings and not parsed by the VIN driver [1] > Niklas (but Simon and Geert seems to agree here) opposed to that > patch, as those properties where described in 'video-interfaces.txt' and > even if not parsed by the current driver implementation, they actually > describe hardware. I rebated that only properties listed in the device > bindings documentation should actually be used, and having properties > not parsed by the driver confuses users, which may expect changing > them modifies the interface configuration, which does not happens at > the moment. > > This came out as a middle ground from a discussion with Niklas. As > stated in the cover letter if this patch makes someone uncomfortable, feel > free to drop it not to hold back the rest of the series which has been > well received instead. What I don't agree with and sparked this debate from my side was the deletion of properties in dts files which correctly does describe the bus but which are not currently parsed by the driver. To me that is decreasing the value of the dts. If on the other hand the goal is to deprecate a property from the video-interfaces.txt by slowly removing them from dts where the driver don't use them I'm all for it. But I don't think this is the case here right? > > Thanks > j > > [1] https://www.spinics.net/lists/arm-kernel/msg656302.html > > > > - hsync-active: see [1] for description. Default is active high. > > > - vsync-active: see [1] for description. Default is active high. > > > - data-enable-active: polarity of CLKENB signal, see [1] for > > > -- > > > 2.7.4 > > > > > > > -- > > Sakari Ailus > > sakari.ailus@linux.intel.com
Hi Niklas, On Wednesday, 27 June 2018 08:24:31 EEST Niklas Söderlund wrote: > On 2018-06-13 10:54:55 +0200, Jacopo Mondi wrote: > > On Tue, Jun 12, 2018 at 06:45:53PM +0300, Sakari Ailus wrote: > >> On Tue, Jun 12, 2018 at 04:26:06PM +0200, Jacopo Mondi wrote: > >>> Add a note to the R-Car VIN interface bindings to clarify that all > >>> properties listed as generic properties in video-interfaces.txt can > >>> be included in port@0 endpoint, but if not explicitly listed in the > >>> interface bindings documentation, they do not modify it behaviour. > >>> > >>> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > >>> --- > >>> > >>> Documentation/devicetree/bindings/media/rcar_vin.txt | 6 ++++++ > >>> 1 file changed, 6 insertions(+) > >>> > >>> diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt > >>> b/Documentation/devicetree/bindings/media/rcar_vin.txt index > >>> 8130849..03544c7 100644 > >>> --- a/Documentation/devicetree/bindings/media/rcar_vin.txt > >>> +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt > >>> @@ -55,6 +55,12 @@ from local SoC CSI-2 receivers (port1) depending on > >>> SoC. > >>> > >>> instances that are connected to external pins should have port > >>> 0. > >>> > >>> - Optional properties for endpoint nodes of port@0: > >>> + > >>> + All properties described in [1] and which apply to the > >>> selected > >>> + media bus type could be optionally listed here to better > >>> describe > >>> + the current hardware configuration, but only the following > >>> ones do > >>> + actually modify the VIN interface behaviour: > >>> + > > I'm not sure the description have to be as explicit to that the > properties in 'video-interfaces.txt' are not currently used by the > driver. I find it not relevant which ones are used or not, what is > important for me is that all properties in 'video-interfaces.txt' which > can be used to describe the specific bus are valid for the DT > description. I agree with you. The driver is irrelevant in this context. What matters is which properties are applicable to the bus. For instance, if the VIN parallel input supports configurable polarities for the h/v sync signals, hsync-active and vsync-active should be listed in the bindings. On the other hand, if the polarities are fixed, then the properties are not needed. > On a side note, in rcar_vin.txt we have this section describing the Gen2 > bindings: > > The per-board settings Gen2 platforms: > - port sub-node describing a single endpoint connected to the vin > as described in video-interfaces.txt[1]. Only the first one will > be considered as each vin interface has one input port. > > This whole series only deals with documenting the Gen3 optional > properties and not the Gen2. Maybe with parallel input support for Gen3 > patches on there way to making it upstream this series should be > extended to in a good way merge the port@0 optional properties for both > generations of hardware? That would be nice too :-) > >> I don't think this should be needed. You should only have properties > >> that describe the hardware configuration in a given system. > > > > There has been quite some debate on this, and please bear with me > > here for re-proposing it: I started by removing properties in some DT > > files for older Renesas board which listed endpoint properties not > > documented in the VIN's bindings and not parsed by the VIN driver [1] > > Niklas (but Simon and Geert seems to agree here) opposed to that > > patch, as those properties where described in 'video-interfaces.txt' and > > even if not parsed by the current driver implementation, they actually > > describe hardware. I rebated that only properties listed in the device > > bindings documentation should actually be used, and having properties > > not parsed by the driver confuses users, which may expect changing > > them modifies the interface configuration, which does not happens at > > the moment. > > > > This came out as a middle ground from a discussion with Niklas. As > > stated in the cover letter if this patch makes someone uncomfortable, feel > > free to drop it not to hold back the rest of the series which has been > > well received instead. > > What I don't agree with and sparked this debate from my side was the > deletion of properties in dts files which correctly does describe the > bus but which are not currently parsed by the driver. To me that is > decreasing the value of the dts. If on the other hand the goal is to > deprecate a property from the video-interfaces.txt by slowly removing > them from dts where the driver don't use them I'm all for it. But I > don't think this is the case here right? I think you're right, I don't think that's the case. We should not remove properties from the dts files when they correctly describe the hardware and have an added-value. On the other hand, if a property correctly describes the hardware, but is constrained to a single value due to hardware limitations, then we can omit it. > > [1] https://www.spinics.net/lists/arm-kernel/msg656302.html > > > >>> - hsync-active: see [1] for description. Default is active high. > >>> - vsync-active: see [1] for description. Default is active high. > >>> - data-enable-active: polarity of CLKENB signal, see [1] for
Hi Laurent, Niklas, On Mon, Jul 02, 2018 at 10:19:25AM +0300, Laurent Pinchart wrote: > Hi Niklas, > > On Wednesday, 27 June 2018 08:24:31 EEST Niklas Söderlund wrote: > > On 2018-06-13 10:54:55 +0200, Jacopo Mondi wrote: > > > On Tue, Jun 12, 2018 at 06:45:53PM +0300, Sakari Ailus wrote: > > >> On Tue, Jun 12, 2018 at 04:26:06PM +0200, Jacopo Mondi wrote: > > >>> Add a note to the R-Car VIN interface bindings to clarify that all > > >>> properties listed as generic properties in video-interfaces.txt can > > >>> be included in port@0 endpoint, but if not explicitly listed in the > > >>> interface bindings documentation, they do not modify it behaviour. > > >>> > > >>> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > > >>> --- > > >>> > > >>> Documentation/devicetree/bindings/media/rcar_vin.txt | 6 ++++++ > > >>> 1 file changed, 6 insertions(+) > > >>> > > >>> diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt > > >>> b/Documentation/devicetree/bindings/media/rcar_vin.txt index > > >>> 8130849..03544c7 100644 > > >>> --- a/Documentation/devicetree/bindings/media/rcar_vin.txt > > >>> +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt > > >>> @@ -55,6 +55,12 @@ from local SoC CSI-2 receivers (port1) depending on > > >>> SoC. > > >>> > > >>> instances that are connected to external pins should have port > > >>> 0. > > >>> > > >>> - Optional properties for endpoint nodes of port@0: > > >>> + > > >>> + All properties described in [1] and which apply to the > > >>> selected > > >>> + media bus type could be optionally listed here to better > > >>> describe > > >>> + the current hardware configuration, but only the following > > >>> ones do > > >>> + actually modify the VIN interface behaviour: > > >>> + > > > > I'm not sure the description have to be as explicit to that the > > properties in 'video-interfaces.txt' are not currently used by the > > driver. I find it not relevant which ones are used or not, what is > > important for me is that all properties in 'video-interfaces.txt' which > > can be used to describe the specific bus are valid for the DT > > description. > > I agree with you. The driver is irrelevant in this context. What matters is > which properties are applicable to the bus. For instance, if the VIN parallel > input supports configurable polarities for the h/v sync signals, hsync-active > and vsync-active should be listed in the bindings. On the other hand, if the > polarities are fixed, then the properties are not needed. > Fine, I'll surrender then, you're too many to fight against :p Joking aside, I see your points, and I'll resend dropping this last bit and documenting which properties applies to the interface. I can list: - vsync-active (added by this series) - hsync-active (added by this series) - data-enable-active (added by this series) - field-active-even (to be added) I haven't find a way to configure the plck-sample value in the VINs registers. Should we skip it? I also think 'bus-width' and 'data-shift' are not directly configurable in registers but depends on SoC, the selected input interface, and the input image format (see tables at 26.3.1 datasheet revision 1.00), so it makes sense list them as acceptable properties. Do I have your ack on this so I can re-spin? > > On a side note, in rcar_vin.txt we have this section describing the Gen2 > > bindings: > > > > The per-board settings Gen2 platforms: > > - port sub-node describing a single endpoint connected to the vin > > as described in video-interfaces.txt[1]. Only the first one will > > be considered as each vin interface has one input port. > > > > This whole series only deals with documenting the Gen3 optional > > properties and not the Gen2. Maybe with parallel input support for Gen3 > > patches on there way to making it upstream this series should be > > extended to in a good way merge the port@0 optional properties for both > > generations of hardware? > > That would be nice too :-) I see.. Well, I would keep the Gen2/Gen3 sections separate, as they have a different layout of port nodes (Gen2 has a single 'port' node, while Gen3 could have several 'port' nodes enclosed in a 'ports' one). But I could indeed reference the optional endpoint properties of 'port@0' of Gen3 bindings in Gen2 ones. Or the other way around. Do you have any preference? Thanks j > > > >> I don't think this should be needed. You should only have properties > > >> that describe the hardware configuration in a given system. > > > > > > There has been quite some debate on this, and please bear with me > > > here for re-proposing it: I started by removing properties in some DT > > > files for older Renesas board which listed endpoint properties not > > > documented in the VIN's bindings and not parsed by the VIN driver [1] > > > Niklas (but Simon and Geert seems to agree here) opposed to that > > > patch, as those properties where described in 'video-interfaces.txt' and > > > even if not parsed by the current driver implementation, they actually > > > describe hardware. I rebated that only properties listed in the device > > > bindings documentation should actually be used, and having properties > > > not parsed by the driver confuses users, which may expect changing > > > them modifies the interface configuration, which does not happens at > > > the moment. > > > > > > This came out as a middle ground from a discussion with Niklas. As > > > stated in the cover letter if this patch makes someone uncomfortable, feel > > > free to drop it not to hold back the rest of the series which has been > > > well received instead. > > > > What I don't agree with and sparked this debate from my side was the > > deletion of properties in dts files which correctly does describe the > > bus but which are not currently parsed by the driver. To me that is > > decreasing the value of the dts. If on the other hand the goal is to > > deprecate a property from the video-interfaces.txt by slowly removing > > them from dts where the driver don't use them I'm all for it. But I > > don't think this is the case here right? > > I think you're right, I don't think that's the case. > > We should not remove properties from the dts files when they correctly > describe the hardware and have an added-value. On the other hand, if a > property correctly describes the hardware, but is constrained to a single > value due to hardware limitations, then we can omit it. > > > > [1] https://www.spinics.net/lists/arm-kernel/msg656302.html > > > > > >>> - hsync-active: see [1] for description. Default is active high. > > >>> - vsync-active: see [1] for description. Default is active high. > > >>> - data-enable-active: polarity of CLKENB signal, see [1] for > > -- > Regards, > > Laurent Pinchart > > >
Hi Jacopo, Thanks for not giving up on this work :-) On 2018-07-03 21:52:38 +0200, Jacopo Mondi wrote: > Hi Laurent, Niklas, > > On Mon, Jul 02, 2018 at 10:19:25AM +0300, Laurent Pinchart wrote: > > Hi Niklas, > > > > On Wednesday, 27 June 2018 08:24:31 EEST Niklas Söderlund wrote: > > > On 2018-06-13 10:54:55 +0200, Jacopo Mondi wrote: > > > > On Tue, Jun 12, 2018 at 06:45:53PM +0300, Sakari Ailus wrote: > > > >> On Tue, Jun 12, 2018 at 04:26:06PM +0200, Jacopo Mondi wrote: > > > >>> Add a note to the R-Car VIN interface bindings to clarify that all > > > >>> properties listed as generic properties in video-interfaces.txt can > > > >>> be included in port@0 endpoint, but if not explicitly listed in the > > > >>> interface bindings documentation, they do not modify it behaviour. > > > >>> > > > >>> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > > > >>> --- > > > >>> > > > >>> Documentation/devicetree/bindings/media/rcar_vin.txt | 6 ++++++ > > > >>> 1 file changed, 6 insertions(+) > > > >>> > > > >>> diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt > > > >>> b/Documentation/devicetree/bindings/media/rcar_vin.txt index > > > >>> 8130849..03544c7 100644 > > > >>> --- a/Documentation/devicetree/bindings/media/rcar_vin.txt > > > >>> +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt > > > >>> @@ -55,6 +55,12 @@ from local SoC CSI-2 receivers (port1) depending on > > > >>> SoC. > > > >>> > > > >>> instances that are connected to external pins should have port > > > >>> 0. > > > >>> > > > >>> - Optional properties for endpoint nodes of port@0: > > > >>> + > > > >>> + All properties described in [1] and which apply to the > > > >>> selected > > > >>> + media bus type could be optionally listed here to better > > > >>> describe > > > >>> + the current hardware configuration, but only the following > > > >>> ones do > > > >>> + actually modify the VIN interface behaviour: > > > >>> + > > > > > > I'm not sure the description have to be as explicit to that the > > > properties in 'video-interfaces.txt' are not currently used by the > > > driver. I find it not relevant which ones are used or not, what is > > > important for me is that all properties in 'video-interfaces.txt' which > > > can be used to describe the specific bus are valid for the DT > > > description. > > > > I agree with you. The driver is irrelevant in this context. What matters is > > which properties are applicable to the bus. For instance, if the VIN parallel > > input supports configurable polarities for the h/v sync signals, hsync-active > > and vsync-active should be listed in the bindings. On the other hand, if the > > polarities are fixed, then the properties are not needed. > > > > Fine, I'll surrender then, you're too many to fight against :p > > Joking aside, I see your points, and I'll resend dropping this last > bit and documenting which properties applies to the interface. > > I can list: > - vsync-active (added by this series) > - hsync-active (added by this series) > - data-enable-active (added by this series) > - field-active-even (to be added) > > I haven't find a way to configure the plck-sample value in the VINs > registers. Should we skip it? IIRC my findings agree with yours, no register to control plck-sample in the VIN register set. > > I also think 'bus-width' and 'data-shift' are not directly configurable in > registers but depends on SoC, the selected input interface, and the > input image format (see tables at 26.3.1 datasheet revision 1.00), so > it makes sense list them as acceptable properties. > > Do I have your ack on this so I can re-spin? I think I understand your plan and I think it sounds ok, please try it :-) > > > > On a side note, in rcar_vin.txt we have this section describing the Gen2 > > > bindings: > > > > > > The per-board settings Gen2 platforms: > > > - port sub-node describing a single endpoint connected to the vin > > > as described in video-interfaces.txt[1]. Only the first one will > > > be considered as each vin interface has one input port. > > > > > > This whole series only deals with documenting the Gen3 optional > > > properties and not the Gen2. Maybe with parallel input support for Gen3 > > > patches on there way to making it upstream this series should be > > > extended to in a good way merge the port@0 optional properties for both > > > generations of hardware? > > > > That would be nice too :-) > > I see.. > > Well, I would keep the Gen2/Gen3 sections separate, as they have a > different layout of port nodes (Gen2 has a single 'port' node, while Gen3 could > have several 'port' nodes enclosed in a 'ports' one). > > But I could indeed reference the optional endpoint properties of > 'port@0' of Gen3 bindings in Gen2 ones. Or the other way around. Do > you have any preference? My preference would be to list the properties in the Gen2 section and in the Gen3 port@0 section refer to the Gen2 optional properties. > > Thanks > j > > > > > > > >> I don't think this should be needed. You should only have properties > > > >> that describe the hardware configuration in a given system. > > > > > > > > There has been quite some debate on this, and please bear with me > > > > here for re-proposing it: I started by removing properties in some DT > > > > files for older Renesas board which listed endpoint properties not > > > > documented in the VIN's bindings and not parsed by the VIN driver [1] > > > > Niklas (but Simon and Geert seems to agree here) opposed to that > > > > patch, as those properties where described in 'video-interfaces.txt' and > > > > even if not parsed by the current driver implementation, they actually > > > > describe hardware. I rebated that only properties listed in the device > > > > bindings documentation should actually be used, and having properties > > > > not parsed by the driver confuses users, which may expect changing > > > > them modifies the interface configuration, which does not happens at > > > > the moment. > > > > > > > > This came out as a middle ground from a discussion with Niklas. As > > > > stated in the cover letter if this patch makes someone uncomfortable, feel > > > > free to drop it not to hold back the rest of the series which has been > > > > well received instead. > > > > > > What I don't agree with and sparked this debate from my side was the > > > deletion of properties in dts files which correctly does describe the > > > bus but which are not currently parsed by the driver. To me that is > > > decreasing the value of the dts. If on the other hand the goal is to > > > deprecate a property from the video-interfaces.txt by slowly removing > > > them from dts where the driver don't use them I'm all for it. But I > > > don't think this is the case here right? > > > > I think you're right, I don't think that's the case. > > > > We should not remove properties from the dts files when they correctly > > describe the hardware and have an added-value. On the other hand, if a > > property correctly describes the hardware, but is constrained to a single > > value due to hardware limitations, then we can omit it. > > > > > > [1] https://www.spinics.net/lists/arm-kernel/msg656302.html > > > > > > > >>> - hsync-active: see [1] for description. Default is active high. > > > >>> - vsync-active: see [1] for description. Default is active high. > > > >>> - data-enable-active: polarity of CLKENB signal, see [1] for > > > > -- > > Regards, > > > > Laurent Pinchart > > > > > >
diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 8130849..03544c7 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -55,6 +55,12 @@ from local SoC CSI-2 receivers (port1) depending on SoC. instances that are connected to external pins should have port 0. - Optional properties for endpoint nodes of port@0: + + All properties described in [1] and which apply to the selected + media bus type could be optionally listed here to better describe + the current hardware configuration, but only the following ones do + actually modify the VIN interface behaviour: + - hsync-active: see [1] for description. Default is active high. - vsync-active: see [1] for description. Default is active high. - data-enable-active: polarity of CLKENB signal, see [1] for
Add a note to the R-Car VIN interface bindings to clarify that all properties listed as generic properties in video-interfaces.txt can be included in port@0 endpoint, but if not explicitly listed in the interface bindings documentation, they do not modify it behaviour. Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> --- Documentation/devicetree/bindings/media/rcar_vin.txt | 6 ++++++ 1 file changed, 6 insertions(+)