diff mbox

[v7,1/4] i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller

Message ID 1528823348-30532-2-git-send-email-kramasub@codeaurora.org (mailing list archive)
State Not Applicable, archived
Delegated to: Andy Gross
Headers show

Commit Message

Karthikeyan Ramasubramanian June 12, 2018, 5:09 p.m. UTC
This bus driver supports the GENI based i2c hardware controller in the
Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
module supporting a wide range of serial interfaces including I2C. The
driver supports FIFO mode and DMA mode of transfer and switches modes
dynamically depending on the size of the transfer.

Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
---
 drivers/i2c/busses/Kconfig         |  13 +
 drivers/i2c/busses/Makefile        |   1 +
 drivers/i2c/busses/i2c-qcom-geni.c | 649 +++++++++++++++++++++++++++++++++++++
 3 files changed, 663 insertions(+)
 create mode 100644 drivers/i2c/busses/i2c-qcom-geni.c

Comments

Stephen Boyd June 13, 2018, 4:10 p.m. UTC | #1
Quoting Karthikeyan Ramasubramanian (2018-06-12 10:09:05)
> This bus driver supports the GENI based i2c hardware controller in the
> Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
> module supporting a wide range of serial interfaces including I2C. The
> driver supports FIFO mode and DMA mode of transfer and switches modes
> dynamically depending on the size of the transfer.
> 
> Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
> Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
> Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
> Reviewed-by: Douglas Anderson <dianders@chromium.org>
> ---

Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>

--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Wolfram Sang July 29, 2018, 10:32 a.m. UTC | #2
On Tue, Jun 12, 2018 at 11:09:05AM -0600, Karthikeyan Ramasubramanian wrote:
> This bus driver supports the GENI based i2c hardware controller in the
> Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
> module supporting a wide range of serial interfaces including I2C. The
> driver supports FIFO mode and DMA mode of transfer and switches modes
> dynamically depending on the size of the transfer.
> 
> Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
> Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
> Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
> Reviewed-by: Douglas Anderson <dianders@chromium.org>

Looks good except one minor thing:

> +	pm_runtime_set_suspended(gi2c->se.dev);
> +	pm_runtime_set_autosuspend_delay(gi2c->se.dev, I2C_AUTO_SUSPEND_DELAY);
> +	pm_runtime_use_autosuspend(gi2c->se.dev);
> +	pm_runtime_enable(gi2c->se.dev);
> +	i2c_add_adapter(&gi2c->adap);
> +
> +	return 0;

i2c_add_adapter can fail. So, I'd guess you want to check the return
value and move it above the pm_runtime calls?
Karthikeyan Ramasubramanian July 30, 2018, 5:15 p.m. UTC | #3
On 7/29/2018 4:32 AM, Wolfram Sang wrote:
> On Tue, Jun 12, 2018 at 11:09:05AM -0600, Karthikeyan Ramasubramanian wrote:
>> This bus driver supports the GENI based i2c hardware controller in the
>> Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
>> module supporting a wide range of serial interfaces including I2C. The
>> driver supports FIFO mode and DMA mode of transfer and switches modes
>> dynamically depending on the size of the transfer.
>>
>> Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
>> Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
>> Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
>> Reviewed-by: Douglas Anderson <dianders@chromium.org>
> 
> Looks good except one minor thing:
> 
>> +	pm_runtime_set_suspended(gi2c->se.dev);
>> +	pm_runtime_set_autosuspend_delay(gi2c->se.dev, I2C_AUTO_SUSPEND_DELAY);
>> +	pm_runtime_use_autosuspend(gi2c->se.dev);
>> +	pm_runtime_enable(gi2c->se.dev);
>> +	i2c_add_adapter(&gi2c->adap);
>> +
>> +	return 0;
> 
> i2c_add_adapter can fail. So, I'd guess you want to check the return
> value and move it above the pm_runtime calls?
> 
Sure, I will update and upload a new patchset.

Regards,
Karthik.
diff mbox

Patch

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index fce9f2c..cfbf16c 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -828,6 +828,19 @@  config I2C_PXA_SLAVE
 	  is necessary for systems where the PXA may be a target on the
 	  I2C bus.
 
+config I2C_QCOM_GENI
+	tristate "Qualcomm Technologies Inc.'s GENI based I2C controller"
+	depends on ARCH_QCOM || COMPILE_TEST
+	depends on QCOM_GENI_SE
+	help
+	  This driver supports GENI serial engine based I2C controller in
+	  master mode on the Qualcomm Technologies Inc.'s SoCs. If you say
+	  yes to this option, support will be included for the built-in I2C
+	  interface on the Qualcomm Technologies Inc.'s SoCs.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-qcom-geni.
+
 config I2C_QUP
 	tristate "Qualcomm QUP based I2C controller"
 	depends on ARCH_QCOM
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 189e34b..8457dc3 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -83,6 +83,7 @@  obj-$(CONFIG_I2C_PNX)		+= i2c-pnx.o
 obj-$(CONFIG_I2C_PUV3)		+= i2c-puv3.o
 obj-$(CONFIG_I2C_PXA)		+= i2c-pxa.o
 obj-$(CONFIG_I2C_PXA_PCI)	+= i2c-pxa-pci.o
+obj-$(CONFIG_I2C_QCOM_GENI)	+= i2c-qcom-geni.o
 obj-$(CONFIG_I2C_QUP)		+= i2c-qup.o
 obj-$(CONFIG_I2C_RIIC)		+= i2c-riic.o
 obj-$(CONFIG_I2C_RK3X)		+= i2c-rk3x.o
diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
new file mode 100644
index 0000000..54bcd1a
--- /dev/null
+++ b/drivers/i2c/busses/i2c-qcom-geni.c
@@ -0,0 +1,649 @@ 
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017-2018, The Linux Foundation. All rights reserved.
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/qcom-geni-se.h>
+#include <linux/spinlock.h>
+
+#define SE_I2C_TX_TRANS_LEN		0x26c
+#define SE_I2C_RX_TRANS_LEN		0x270
+#define SE_I2C_SCL_COUNTERS		0x278
+
+#define SE_I2C_ERR  (M_CMD_OVERRUN_EN | M_ILLEGAL_CMD_EN | M_CMD_FAILURE_EN |\
+			M_GP_IRQ_1_EN | M_GP_IRQ_3_EN | M_GP_IRQ_4_EN)
+#define SE_I2C_ABORT		BIT(1)
+
+/* M_CMD OP codes for I2C */
+#define I2C_WRITE		0x1
+#define I2C_READ		0x2
+#define I2C_WRITE_READ		0x3
+#define I2C_ADDR_ONLY		0x4
+#define I2C_BUS_CLEAR		0x6
+#define I2C_STOP_ON_BUS		0x7
+/* M_CMD params for I2C */
+#define PRE_CMD_DELAY		BIT(0)
+#define TIMESTAMP_BEFORE	BIT(1)
+#define STOP_STRETCH		BIT(2)
+#define TIMESTAMP_AFTER		BIT(3)
+#define POST_COMMAND_DELAY	BIT(4)
+#define IGNORE_ADD_NACK		BIT(6)
+#define READ_FINISHED_WITH_ACK	BIT(7)
+#define BYPASS_ADDR_PHASE	BIT(8)
+#define SLV_ADDR_MSK		GENMASK(15, 9)
+#define SLV_ADDR_SHFT		9
+/* I2C SCL COUNTER fields */
+#define HIGH_COUNTER_MSK	GENMASK(29, 20)
+#define HIGH_COUNTER_SHFT	20
+#define LOW_COUNTER_MSK		GENMASK(19, 10)
+#define LOW_COUNTER_SHFT	10
+#define CYCLE_COUNTER_MSK	GENMASK(9, 0)
+
+enum geni_i2c_err_code {
+	GP_IRQ0,
+	NACK,
+	GP_IRQ2,
+	BUS_PROTO,
+	ARB_LOST,
+	GP_IRQ5,
+	GENI_OVERRUN,
+	GENI_ILLEGAL_CMD,
+	GENI_ABORT_DONE,
+	GENI_TIMEOUT,
+};
+
+#define DM_I2C_CB_ERR		((BIT(NACK) | BIT(BUS_PROTO) | BIT(ARB_LOST)) \
+									<< 5)
+
+#define I2C_AUTO_SUSPEND_DELAY	250
+#define KHZ(freq)		(1000 * freq)
+#define PACKING_BYTES_PW	4
+
+#define ABORT_TIMEOUT		HZ
+#define XFER_TIMEOUT		HZ
+#define RST_TIMEOUT		HZ
+
+struct geni_i2c_dev {
+	struct geni_se se;
+	u32 tx_wm;
+	int irq;
+	int err;
+	struct i2c_adapter adap;
+	struct completion done;
+	struct i2c_msg *cur;
+	int cur_wr;
+	int cur_rd;
+	spinlock_t lock;
+	u32 clk_freq_out;
+	const struct geni_i2c_clk_fld *clk_fld;
+};
+
+struct geni_i2c_err_log {
+	int err;
+	const char *msg;
+};
+
+static const struct geni_i2c_err_log gi2c_log[] = {
+	[GP_IRQ0] = {-EIO, "Unknown I2C err GP_IRQ0"},
+	[NACK] = {-ENXIO, "NACK: slv unresponsive, check its power/reset-ln"},
+	[GP_IRQ2] = {-EIO, "Unknown I2C err GP IRQ2"},
+	[BUS_PROTO] = {-EPROTO, "Bus proto err, noisy/unepxected start/stop"},
+	[ARB_LOST] = {-EAGAIN, "Bus arbitration lost, clock line undriveable"},
+	[GP_IRQ5] = {-EIO, "Unknown I2C err GP IRQ5"},
+	[GENI_OVERRUN] = {-EIO, "Cmd overrun, check GENI cmd-state machine"},
+	[GENI_ILLEGAL_CMD] = {-EIO, "Illegal cmd, check GENI cmd-state machine"},
+	[GENI_ABORT_DONE] = {-ETIMEDOUT, "Abort after timeout successful"},
+	[GENI_TIMEOUT] = {-ETIMEDOUT, "I2C TXN timed out"},
+};
+
+struct geni_i2c_clk_fld {
+	u32	clk_freq_out;
+	u8	clk_div;
+	u8	t_high_cnt;
+	u8	t_low_cnt;
+	u8	t_cycle_cnt;
+};
+
+/*
+ * Hardware uses the underlying formula to calculate time periods of
+ * SCL clock cycle. Firmware uses some additional cycles excluded from the
+ * below formula and it is confirmed that the time periods are within
+ * specification limits.
+ *
+ * time of high period of SCL: t_high = (t_high_cnt * clk_div) / source_clock
+ * time of low period of SCL: t_low = (t_low_cnt * clk_div) / source_clock
+ * time of full period of SCL: t_cycle = (t_cycle_cnt * clk_div) / source_clock
+ * clk_freq_out = t / t_cycle
+ * source_clock = 19.2 MHz
+ */
+static const struct geni_i2c_clk_fld geni_i2c_clk_map[] = {
+	{KHZ(100), 7, 10, 11, 26},
+	{KHZ(400), 2,  5, 12, 24},
+	{KHZ(1000), 1, 3,  9, 18},
+};
+
+static int geni_i2c_clk_map_idx(struct geni_i2c_dev *gi2c)
+{
+	int i;
+	const struct geni_i2c_clk_fld *itr = geni_i2c_clk_map;
+
+	for (i = 0; i < ARRAY_SIZE(geni_i2c_clk_map); i++, itr++) {
+		if (itr->clk_freq_out == gi2c->clk_freq_out) {
+			gi2c->clk_fld = itr;
+			return 0;
+		}
+	}
+	return -EINVAL;
+}
+
+static void qcom_geni_i2c_conf(struct geni_i2c_dev *gi2c)
+{
+	const struct geni_i2c_clk_fld *itr = gi2c->clk_fld;
+	u32 val;
+
+	writel_relaxed(0, gi2c->se.base + SE_GENI_CLK_SEL);
+
+	val = (itr->clk_div << CLK_DIV_SHFT) | SER_CLK_EN;
+	writel_relaxed(val, gi2c->se.base + GENI_SER_M_CLK_CFG);
+
+	val = itr->t_high_cnt << HIGH_COUNTER_SHFT;
+	val |= itr->t_low_cnt << LOW_COUNTER_SHFT;
+	val |= itr->t_cycle_cnt;
+	writel_relaxed(val, gi2c->se.base + SE_I2C_SCL_COUNTERS);
+}
+
+static void geni_i2c_err_misc(struct geni_i2c_dev *gi2c)
+{
+	u32 m_cmd = readl_relaxed(gi2c->se.base + SE_GENI_M_CMD0);
+	u32 m_stat = readl_relaxed(gi2c->se.base + SE_GENI_M_IRQ_STATUS);
+	u32 geni_s = readl_relaxed(gi2c->se.base + SE_GENI_STATUS);
+	u32 geni_ios = readl_relaxed(gi2c->se.base + SE_GENI_IOS);
+	u32 dma = readl_relaxed(gi2c->se.base + SE_GENI_DMA_MODE_EN);
+	u32 rx_st, tx_st;
+
+	if (dma) {
+		rx_st = readl_relaxed(gi2c->se.base + SE_DMA_RX_IRQ_STAT);
+		tx_st = readl_relaxed(gi2c->se.base + SE_DMA_TX_IRQ_STAT);
+	} else {
+		rx_st = readl_relaxed(gi2c->se.base + SE_GENI_RX_FIFO_STATUS);
+		tx_st = readl_relaxed(gi2c->se.base + SE_GENI_TX_FIFO_STATUS);
+	}
+	dev_dbg(gi2c->se.dev, "DMA:%d tx_stat:0x%x, rx_stat:0x%x, irq-stat:0x%x\n",
+		dma, tx_st, rx_st, m_stat);
+	dev_dbg(gi2c->se.dev, "m_cmd:0x%x, geni_status:0x%x, geni_ios:0x%x\n",
+		m_cmd, geni_s, geni_ios);
+}
+
+static void geni_i2c_err(struct geni_i2c_dev *gi2c, int err)
+{
+	if (!gi2c->err)
+		gi2c->err = gi2c_log[err].err;
+	if (gi2c->cur)
+		dev_dbg(gi2c->se.dev, "len:%d, slv-addr:0x%x, RD/WR:%d\n",
+			gi2c->cur->len, gi2c->cur->addr, gi2c->cur->flags);
+
+	if (err != NACK && err != GENI_ABORT_DONE) {
+		dev_err(gi2c->se.dev, "%s\n", gi2c_log[err].msg);
+		geni_i2c_err_misc(gi2c);
+	}
+}
+
+static irqreturn_t geni_i2c_irq(int irq, void *dev)
+{
+	struct geni_i2c_dev *gi2c = dev;
+	int j;
+	u32 m_stat;
+	u32 rx_st;
+	u32 dm_tx_st;
+	u32 dm_rx_st;
+	u32 dma;
+	struct i2c_msg *cur;
+	unsigned long flags;
+
+	spin_lock_irqsave(&gi2c->lock, flags);
+	m_stat = readl_relaxed(gi2c->se.base + SE_GENI_M_IRQ_STATUS);
+	rx_st = readl_relaxed(gi2c->se.base + SE_GENI_RX_FIFO_STATUS);
+	dm_tx_st = readl_relaxed(gi2c->se.base + SE_DMA_TX_IRQ_STAT);
+	dm_rx_st = readl_relaxed(gi2c->se.base + SE_DMA_RX_IRQ_STAT);
+	dma = readl_relaxed(gi2c->se.base + SE_GENI_DMA_MODE_EN);
+	cur = gi2c->cur;
+
+	if (!cur ||
+	    m_stat & (M_CMD_FAILURE_EN | M_CMD_ABORT_EN) ||
+	    dm_rx_st & (DM_I2C_CB_ERR)) {
+		if (m_stat & M_GP_IRQ_1_EN)
+			geni_i2c_err(gi2c, NACK);
+		if (m_stat & M_GP_IRQ_3_EN)
+			geni_i2c_err(gi2c, BUS_PROTO);
+		if (m_stat & M_GP_IRQ_4_EN)
+			geni_i2c_err(gi2c, ARB_LOST);
+		if (m_stat & M_CMD_OVERRUN_EN)
+			geni_i2c_err(gi2c, GENI_OVERRUN);
+		if (m_stat & M_ILLEGAL_CMD_EN)
+			geni_i2c_err(gi2c, GENI_ILLEGAL_CMD);
+		if (m_stat & M_CMD_ABORT_EN)
+			geni_i2c_err(gi2c, GENI_ABORT_DONE);
+		if (m_stat & M_GP_IRQ_0_EN)
+			geni_i2c_err(gi2c, GP_IRQ0);
+
+		/* Disable the TX Watermark interrupt to stop TX */
+		if (!dma)
+			writel_relaxed(0, gi2c->se.base +
+					   SE_GENI_TX_WATERMARK_REG);
+		goto irqret;
+	}
+
+	if (dma) {
+		dev_dbg(gi2c->se.dev, "i2c dma tx:0x%x, dma rx:0x%x\n",
+			dm_tx_st, dm_rx_st);
+		goto irqret;
+	}
+
+	if (cur->flags & I2C_M_RD &&
+	    m_stat & (M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN)) {
+		u32 rxcnt = rx_st & RX_FIFO_WC_MSK;
+
+		for (j = 0; j < rxcnt; j++) {
+			u32 val;
+			int p = 0;
+
+			val = readl_relaxed(gi2c->se.base + SE_GENI_RX_FIFOn);
+			while (gi2c->cur_rd < cur->len && p < sizeof(val)) {
+				cur->buf[gi2c->cur_rd++] = val & 0xff;
+				val >>= 8;
+				p++;
+			}
+			if (gi2c->cur_rd == cur->len)
+				break;
+		}
+	} else if (!(cur->flags & I2C_M_RD) &&
+		   m_stat & M_TX_FIFO_WATERMARK_EN) {
+		for (j = 0; j < gi2c->tx_wm; j++) {
+			u32 temp;
+			u32 val = 0;
+			int p = 0;
+
+			while (gi2c->cur_wr < cur->len && p < sizeof(val)) {
+				temp = cur->buf[gi2c->cur_wr++];
+				val |= temp << (p * 8);
+				p++;
+			}
+			writel_relaxed(val, gi2c->se.base + SE_GENI_TX_FIFOn);
+			/* TX Complete, Disable the TX Watermark interrupt */
+			if (gi2c->cur_wr == cur->len) {
+				writel_relaxed(0, gi2c->se.base +
+						SE_GENI_TX_WATERMARK_REG);
+				break;
+			}
+		}
+	}
+irqret:
+	if (m_stat)
+		writel_relaxed(m_stat, gi2c->se.base + SE_GENI_M_IRQ_CLEAR);
+
+	if (dma) {
+		if (dm_tx_st)
+			writel_relaxed(dm_tx_st, gi2c->se.base +
+						SE_DMA_TX_IRQ_CLR);
+		if (dm_rx_st)
+			writel_relaxed(dm_rx_st, gi2c->se.base +
+						SE_DMA_RX_IRQ_CLR);
+	}
+	/* if this is err with done-bit not set, handle that through timeout. */
+	if (m_stat & M_CMD_DONE_EN || m_stat & M_CMD_ABORT_EN)
+		complete(&gi2c->done);
+	else if (dm_tx_st & TX_DMA_DONE || dm_tx_st & TX_RESET_DONE)
+		complete(&gi2c->done);
+	else if (dm_rx_st & RX_DMA_DONE || dm_rx_st & RX_RESET_DONE)
+		complete(&gi2c->done);
+
+	spin_unlock_irqrestore(&gi2c->lock, flags);
+	return IRQ_HANDLED;
+}
+
+static void geni_i2c_abort_xfer(struct geni_i2c_dev *gi2c)
+{
+	u32 val;
+	unsigned long time_left = ABORT_TIMEOUT;
+	unsigned long flags;
+
+	spin_lock_irqsave(&gi2c->lock, flags);
+	geni_i2c_err(gi2c, GENI_TIMEOUT);
+	gi2c->cur = NULL;
+	geni_se_abort_m_cmd(&gi2c->se);
+	spin_unlock_irqrestore(&gi2c->lock, flags);
+	do {
+		time_left = wait_for_completion_timeout(&gi2c->done, time_left);
+		val = readl_relaxed(gi2c->se.base + SE_GENI_M_IRQ_STATUS);
+	} while (!(val & M_CMD_ABORT_EN) && time_left);
+
+	if (!(val & M_CMD_ABORT_EN))
+		dev_err(gi2c->se.dev, "Timeout abort_m_cmd\n");
+}
+
+static void geni_i2c_rx_fsm_rst(struct geni_i2c_dev *gi2c)
+{
+	u32 val;
+	unsigned long time_left = RST_TIMEOUT;
+
+	writel_relaxed(1, gi2c->se.base + SE_DMA_RX_FSM_RST);
+	do {
+		time_left = wait_for_completion_timeout(&gi2c->done, time_left);
+		val = readl_relaxed(gi2c->se.base + SE_DMA_RX_IRQ_STAT);
+	} while (!(val & RX_RESET_DONE) && time_left);
+
+	if (!(val & RX_RESET_DONE))
+		dev_err(gi2c->se.dev, "Timeout resetting RX_FSM\n");
+}
+
+static void geni_i2c_tx_fsm_rst(struct geni_i2c_dev *gi2c)
+{
+	u32 val;
+	unsigned long time_left = RST_TIMEOUT;
+
+	writel_relaxed(1, gi2c->se.base + SE_DMA_TX_FSM_RST);
+	do {
+		time_left = wait_for_completion_timeout(&gi2c->done, time_left);
+		val = readl_relaxed(gi2c->se.base + SE_DMA_TX_IRQ_STAT);
+	} while (!(val & TX_RESET_DONE) && time_left);
+
+	if (!(val & TX_RESET_DONE))
+		dev_err(gi2c->se.dev, "Timeout resetting TX_FSM\n");
+}
+
+static int geni_i2c_rx_one_msg(struct geni_i2c_dev *gi2c, struct i2c_msg *msg,
+				u32 m_param)
+{
+	dma_addr_t rx_dma;
+	enum geni_se_xfer_mode mode;
+	unsigned long time_left = XFER_TIMEOUT;
+
+	gi2c->cur = msg;
+	mode = msg->len > 32 ? GENI_SE_DMA : GENI_SE_FIFO;
+	geni_se_select_mode(&gi2c->se, mode);
+	writel_relaxed(msg->len, gi2c->se.base + SE_I2C_RX_TRANS_LEN);
+	geni_se_setup_m_cmd(&gi2c->se, I2C_READ, m_param);
+	if (mode == GENI_SE_DMA) {
+		int ret;
+
+		ret = geni_se_rx_dma_prep(&gi2c->se, msg->buf, msg->len,
+								&rx_dma);
+		if (ret) {
+			mode = GENI_SE_FIFO;
+			geni_se_select_mode(&gi2c->se, mode);
+		}
+	}
+
+	time_left = wait_for_completion_timeout(&gi2c->done, XFER_TIMEOUT);
+	if (!time_left)
+		geni_i2c_abort_xfer(gi2c);
+
+	gi2c->cur_rd = 0;
+	if (mode == GENI_SE_DMA) {
+		if (gi2c->err)
+			geni_i2c_rx_fsm_rst(gi2c);
+		geni_se_rx_dma_unprep(&gi2c->se, rx_dma, msg->len);
+	}
+	return gi2c->err;
+}
+
+static int geni_i2c_tx_one_msg(struct geni_i2c_dev *gi2c, struct i2c_msg *msg,
+				u32 m_param)
+{
+	dma_addr_t tx_dma;
+	enum geni_se_xfer_mode mode;
+	unsigned long time_left;
+
+	gi2c->cur = msg;
+	mode = msg->len > 32 ? GENI_SE_DMA : GENI_SE_FIFO;
+	geni_se_select_mode(&gi2c->se, mode);
+	writel_relaxed(msg->len, gi2c->se.base + SE_I2C_TX_TRANS_LEN);
+	geni_se_setup_m_cmd(&gi2c->se, I2C_WRITE, m_param);
+	if (mode == GENI_SE_DMA) {
+		int ret;
+
+		ret = geni_se_tx_dma_prep(&gi2c->se, msg->buf, msg->len,
+								&tx_dma);
+		if (ret) {
+			mode = GENI_SE_FIFO;
+			geni_se_select_mode(&gi2c->se, mode);
+		}
+	}
+
+	if (mode == GENI_SE_FIFO) /* Get FIFO IRQ */
+		writel_relaxed(1, gi2c->se.base + SE_GENI_TX_WATERMARK_REG);
+
+	time_left = wait_for_completion_timeout(&gi2c->done, XFER_TIMEOUT);
+	if (!time_left)
+		geni_i2c_abort_xfer(gi2c);
+
+	gi2c->cur_wr = 0;
+	if (mode == GENI_SE_DMA) {
+		if (gi2c->err)
+			geni_i2c_tx_fsm_rst(gi2c);
+		geni_se_tx_dma_unprep(&gi2c->se, tx_dma, msg->len);
+	}
+	return gi2c->err;
+}
+
+static int geni_i2c_xfer(struct i2c_adapter *adap,
+			 struct i2c_msg msgs[],
+			 int num)
+{
+	struct geni_i2c_dev *gi2c = i2c_get_adapdata(adap);
+	int i, ret;
+
+	gi2c->err = 0;
+	reinit_completion(&gi2c->done);
+	ret = pm_runtime_get_sync(gi2c->se.dev);
+	if (ret < 0) {
+		dev_err(gi2c->se.dev, "error turning SE resources:%d\n", ret);
+		pm_runtime_put_noidle(gi2c->se.dev);
+		/* Set device in suspended since resume failed */
+		pm_runtime_set_suspended(gi2c->se.dev);
+		return ret;
+	}
+
+	qcom_geni_i2c_conf(gi2c);
+	for (i = 0; i < num; i++) {
+		u32 m_param = i < (num - 1) ? STOP_STRETCH : 0;
+
+		m_param |= ((msgs[i].addr << SLV_ADDR_SHFT) & SLV_ADDR_MSK);
+
+		if (msgs[i].flags & I2C_M_RD)
+			ret = geni_i2c_rx_one_msg(gi2c, &msgs[i], m_param);
+		else
+			ret = geni_i2c_tx_one_msg(gi2c, &msgs[i], m_param);
+
+		if (ret)
+			break;
+	}
+	if (ret == 0)
+		ret = num;
+
+	pm_runtime_mark_last_busy(gi2c->se.dev);
+	pm_runtime_put_autosuspend(gi2c->se.dev);
+	gi2c->cur = NULL;
+	gi2c->err = 0;
+	return ret;
+}
+
+static u32 geni_i2c_func(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
+}
+
+static const struct i2c_algorithm geni_i2c_algo = {
+	.master_xfer	= geni_i2c_xfer,
+	.functionality	= geni_i2c_func,
+};
+
+static int geni_i2c_probe(struct platform_device *pdev)
+{
+	struct geni_i2c_dev *gi2c;
+	struct resource *res;
+	u32 proto, tx_depth;
+	int ret;
+
+	gi2c = devm_kzalloc(&pdev->dev, sizeof(*gi2c), GFP_KERNEL);
+	if (!gi2c)
+		return -ENOMEM;
+
+	gi2c->se.dev = &pdev->dev;
+	gi2c->se.wrapper = dev_get_drvdata(pdev->dev.parent);
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	gi2c->se.base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(gi2c->se.base))
+		return PTR_ERR(gi2c->se.base);
+
+	gi2c->se.clk = devm_clk_get(&pdev->dev, "se");
+	if (IS_ERR(gi2c->se.clk)) {
+		ret = PTR_ERR(gi2c->se.clk);
+		dev_err(&pdev->dev, "Err getting SE Core clk %d\n", ret);
+		return ret;
+	}
+
+	ret = device_property_read_u32(&pdev->dev, "clock-frequency",
+							&gi2c->clk_freq_out);
+	if (ret) {
+		dev_info(&pdev->dev,
+			"Bus frequency not specified, default to 100kHz.\n");
+		gi2c->clk_freq_out = KHZ(100);
+	}
+
+	gi2c->irq = platform_get_irq(pdev, 0);
+	if (gi2c->irq < 0) {
+		dev_err(&pdev->dev, "IRQ error for i2c-geni\n");
+		return gi2c->irq;
+	}
+
+	ret = geni_i2c_clk_map_idx(gi2c);
+	if (ret) {
+		dev_err(&pdev->dev, "Invalid clk frequency %d Hz: %d\n",
+			gi2c->clk_freq_out, ret);
+		return ret;
+	}
+
+	gi2c->adap.algo = &geni_i2c_algo;
+	init_completion(&gi2c->done);
+	spin_lock_init(&gi2c->lock);
+	platform_set_drvdata(pdev, gi2c);
+	ret = devm_request_irq(&pdev->dev, gi2c->irq, geni_i2c_irq,
+			       IRQF_TRIGGER_HIGH, "i2c_geni", gi2c);
+	if (ret) {
+		dev_err(&pdev->dev, "Request_irq failed:%d: err:%d\n",
+			gi2c->irq, ret);
+		return ret;
+	}
+	/* Disable the interrupt so that the system can enter low-power mode */
+	disable_irq(gi2c->irq);
+	i2c_set_adapdata(&gi2c->adap, gi2c);
+	gi2c->adap.dev.parent = &pdev->dev;
+	gi2c->adap.dev.of_node = pdev->dev.of_node;
+	strlcpy(gi2c->adap.name, "Geni-I2C", sizeof(gi2c->adap.name));
+
+	ret = geni_se_resources_on(&gi2c->se);
+	if (ret) {
+		dev_err(&pdev->dev, "Error turning on resources %d\n", ret);
+		return ret;
+	}
+	proto = geni_se_read_proto(&gi2c->se);
+	tx_depth = geni_se_get_tx_fifo_depth(&gi2c->se);
+	if (proto != GENI_SE_I2C) {
+		dev_err(&pdev->dev, "Invalid proto %d\n", proto);
+		geni_se_resources_off(&gi2c->se);
+		return -ENXIO;
+	}
+	gi2c->tx_wm = tx_depth - 1;
+	geni_se_init(&gi2c->se, gi2c->tx_wm, tx_depth);
+	geni_se_config_packing(&gi2c->se, BITS_PER_BYTE, PACKING_BYTES_PW,
+							true, true, true);
+	geni_se_resources_off(&gi2c->se);
+	dev_dbg(&pdev->dev, "i2c fifo/se-dma mode. fifo depth:%d\n", tx_depth);
+
+	pm_runtime_set_suspended(gi2c->se.dev);
+	pm_runtime_set_autosuspend_delay(gi2c->se.dev, I2C_AUTO_SUSPEND_DELAY);
+	pm_runtime_use_autosuspend(gi2c->se.dev);
+	pm_runtime_enable(gi2c->se.dev);
+	i2c_add_adapter(&gi2c->adap);
+
+	return 0;
+}
+
+static int geni_i2c_remove(struct platform_device *pdev)
+{
+	struct geni_i2c_dev *gi2c = platform_get_drvdata(pdev);
+
+	pm_runtime_disable(gi2c->se.dev);
+	i2c_del_adapter(&gi2c->adap);
+	return 0;
+}
+
+static int __maybe_unused geni_i2c_runtime_suspend(struct device *dev)
+{
+	struct geni_i2c_dev *gi2c = dev_get_drvdata(dev);
+
+	disable_irq(gi2c->irq);
+	geni_se_resources_off(&gi2c->se);
+	return 0;
+}
+
+static int __maybe_unused geni_i2c_runtime_resume(struct device *dev)
+{
+	int ret;
+	struct geni_i2c_dev *gi2c = dev_get_drvdata(dev);
+
+	ret = geni_se_resources_on(&gi2c->se);
+	if (ret)
+		return ret;
+
+	enable_irq(gi2c->irq);
+	return 0;
+}
+
+static int __maybe_unused geni_i2c_suspend_noirq(struct device *dev)
+{
+	if (!pm_runtime_suspended(dev)) {
+		geni_i2c_runtime_suspend(dev);
+		pm_runtime_disable(dev);
+		pm_runtime_set_suspended(dev);
+		pm_runtime_enable(dev);
+	}
+	return 0;
+}
+
+static const struct dev_pm_ops geni_i2c_pm_ops = {
+	SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(geni_i2c_suspend_noirq, NULL)
+	SET_RUNTIME_PM_OPS(geni_i2c_runtime_suspend, geni_i2c_runtime_resume,
+									NULL)
+};
+
+static const struct of_device_id geni_i2c_dt_match[] = {
+	{ .compatible = "qcom,geni-i2c" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, geni_i2c_dt_match);
+
+static struct platform_driver geni_i2c_driver = {
+	.probe  = geni_i2c_probe,
+	.remove = geni_i2c_remove,
+	.driver = {
+		.name = "geni_i2c",
+		.pm = &geni_i2c_pm_ops,
+		.of_match_table = geni_i2c_dt_match,
+	},
+};
+
+module_platform_driver(geni_i2c_driver);
+
+MODULE_DESCRIPTION("I2C Controller Driver for GENI based QUP cores");
+MODULE_LICENSE("GPL v2");