[v2,3/6] regmap: Add regmap_pipe_read API

Commit Message

Stefan Popa Aug. 1, 2018, 3:17 p.m. UTC

From: Crestez Dan Leonard <[e-mail]>

The regmap API usually assumes that bulk read operations will read a
range of registers but some I2C/SPI devices have certain registers for
which a such a read operation will return data from an internal FIFO
instead. Add an explicit API to support bulk read with pipe rather than
range semantics.

Some linux drivers use regmap_bulk_read or regmap_raw_read for such
registers, for example mpu6050 or bmi150 from IIO. This only happens to
work because when caching is disabled a single regmap read op will map
to a single bus read op (as desired). This breaks if caching is enabled and
reg+1 happens to be a cacheable register.

Without regmap support refactoring a driver to enable regmap caching
requires separate I2C and SPI paths. This is exactly what regmap is
supposed to help avoid.

Suggested-by: Jonathan Cameron <[e-mail]>
Signed-off-by: Crestez Dan Leonard <[e-mail]>
Signed-off-by: Stefan Popa <[e-mail]>
---
Changes in v2:
	Included as part of this patch series as the regmap_pipe_read()
	API will be used to read the data from the FIFO.

 drivers/base/regmap/regmap.c | 64 +++++++++++++++++++++++++++++++++++++++++++-
 include/linux/regmap.h       |  9 +++++++
 2 files changed, 72 insertions(+), 1 deletion(-)

Comments

Mark Brown Aug. 2, 2018, 10:14 a.m. UTC | #1

On Wed, Aug 01, 2018 at 06:17:47PM +0300, Stefan Popa wrote:
> From: Crestez Dan Leonard <[e-mail]>
> 
> The regmap API usually assumes that bulk read operations will read a
> range of registers but some I2C/SPI devices have certain registers for
> which a such a read operation will return data from an internal FIFO
> instead. Add an explicit API to support bulk read with pipe rather than
> range semantics.

If we're going to do this it's probably best to explicitly mark the
registers where it will work otherwise we'll end up confusing ourselves
and corrupting data at some point, provide another op like readable and
so on.  

I'd also suggest calling it something like _noinc (for non-incrementing)
instead of _pipe as I was a bit confused about what a pipe read was.  We
could also have a software implementation for things like ADC outputs
where the register doesn't have the convenient nonincrementing behaviour
but we want to do repeated reads.

Patch

diff --git a/drivers/base/regmap/regmap.c b/drivers/base/regmap/regmap.c
index 3bc8488..73bacbd 100644
--- a/drivers/base/regmap/regmap.c
+++ b/drivers/base/regmap/regmap.c
@@ -2564,7 +2564,69 @@  int regmap_raw_read(struct regmap *map, unsigned int reg, void *val,
 EXPORT_SYMBOL_GPL(regmap_raw_read);
 
 /**
- * regmap_field_read() - Read a value to a single register field
+ * regmap_pipe_read(): Read data from a register with pipe semantics
+ *
+ * @map: Register map to read from
+ * @reg: Register to read from
+ * @val: Pointer to data buffer
+ * @val_len: Length of output buffer in bytes.
+ *
+ * The regmap API usually assumes that bulk bus read operations will read a
+ * range of registers. Some devices have certain registers for which a read
+ * operation read will read from an internal FIFO.
+ *
+ * The target register must be volatile but registers after it can be
+ * completely unrelated cacheable registers.
+ *
+ * This will attempt multiple reads as required to read val_len bytes.
+ *
+ * A value of zero will be returned on success, a negative errno will be
+ * returned in error cases.
+ */
+int regmap_pipe_read(struct regmap *map, unsigned int reg,
+		     void *val, size_t val_len)
+{
+	size_t read_len;
+	int ret;
+
+	if (!map->bus)
+		return -EINVAL;
+	if (!map->bus->read)
+		return -ENOTSUPP;
+	if (val_len % map->format.val_bytes)
+		return -EINVAL;
+	if (!IS_ALIGNED(reg, map->reg_stride))
+		return -EINVAL;
+	if (val_len == 0)
+		return -EINVAL;
+
+	map->lock(map->lock_arg);
+
+	if (!regmap_volatile(map, reg)) {
+		ret = -EINVAL;
+		goto out_unlock;
+	}
+
+	while (val_len) {
+		if (map->max_raw_read && map->max_raw_read < val_len)
+			read_len = map->max_raw_read;
+		else
+			read_len = val_len;
+		ret = _regmap_raw_read(map, reg, val, read_len);
+		if (ret)
+			goto out_unlock;
+		val = ((u8 *)val) + read_len;
+		val_len -= read_len;
+	}
+
+out_unlock:
+	map->unlock(map->lock_arg);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(regmap_pipe_read);
+
+/**
+ * regmap_field_read(): Read a value to a single register field
  *
  * @field: Register field to read from
  * @val: Pointer to store read value
diff --git a/include/linux/regmap.h b/include/linux/regmap.h
index 4f38068..91c5cb6 100644
--- a/include/linux/regmap.h
+++ b/include/linux/regmap.h
@@ -946,6 +946,8 @@  int regmap_raw_write_async(struct regmap *map, unsigned int reg,
 int regmap_read(struct regmap *map, unsigned int reg, unsigned int *val);
 int regmap_raw_read(struct regmap *map, unsigned int reg,
 		    void *val, size_t val_len);
+int regmap_pipe_read(struct regmap *map, unsigned int reg,
+		     void *val, size_t val_len);
 int regmap_bulk_read(struct regmap *map, unsigned int reg, void *val,
 		     size_t val_count);
 int regmap_update_bits_base(struct regmap *map, unsigned int reg,
@@ -1196,6 +1198,13 @@  static inline int regmap_raw_read(struct regmap *map, unsigned int reg,
 	return -EINVAL;
 }
 
+static inline int regmap_pipe_read(struct regmap *map, unsigned int reg,
+				   void *val, size_t val_len)
+{
+	WARN_ONCE(1, "regmap API is disabled");
+	return -EINVAL;
+}
+
 static inline int regmap_bulk_read(struct regmap *map, unsigned int reg,
 				   void *val, size_t val_count)
 {