diff mbox series

[V5,3/8] backlight: qcom-wled: Add new properties for PMI8998

Message ID 1535106467-17843-4-git-send-email-kgunda@codeaurora.org (mailing list archive)
State New, archived
Headers show
Series backlight: qcom-wled: Support for QCOM wled driver | expand

Commit Message

Kiran Gunda Aug. 24, 2018, 10:27 a.m. UTC 
Update the bindings with the new properties used for
PMI8998.

Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
---
Changes from V3:
    - Removed the default values.
    - Removed pmi8998 example.

Changes from V4:
    - modified qcom,enabled-strings property with decimal numbers.

 .../bindings/leds/backlight/qcom-wled.txt          | 76 ++++++++++++++++++----
 1 file changed, 62 insertions(+), 14 deletions(-)

Comments

Pavel Machek Aug. 27, 2018, 10:01 a.m. UTC | #1 
Hi!

On Fri 2018-08-24 15:57:42, Kiran Gunda wrote:
> Update the bindings with the new properties used for
> PMI8998.

> Changes from V3:
>     - Removed the default values.

Why?

> +- qcom,current-limit-microamp
> +	Usage:        optional
> +	Value type:   <u32>
> +	Definition:   uA; per-string current limit; value from 0 to 30000 with
> +		      2500 uA step.
>  
>  - qcom,current-boost-limit
>  	Usage:        optional
>  	Value type:   <u32>
>  	Definition:   mA; boost current limit.
>  		      For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400,
> -		      1680. Default: 805 mA
> +		      1680.
>  		      For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300,
> -		      1500. Default: 970 mA
> +		      1500.
>

I'd say that optional properties should list default values...?

>  - qcom,ovp
>  	Usage:        optional
>  	Value type:   <u32>
>  	Definition:   V; Over-voltage protection limit; one of:
> -		      27, 29, 32, 35. default: 29V
> +		      27, 29, 32, 35.
>  		      This property is supported only for PM8941.
>

Same here.

> +- qcom,ovp-millivolt
> +	Usage:        optional
> +	Value type:   <u32>
> +	Definition:   mV; Over-voltage protection limit;
> +		      For pmi8998: one of 18100, 19600, 29600, 31100
> +		      If this property is not specified for PM8941, it
> +		      falls back to "qcom,ovp" property.
> +

"voltage-limit-millivolt"? "ovp" is not really well known acronym.
									Pavel
Kiran Gunda Aug. 29, 2018, 5:52 a.m. UTC | #2 
On 2018-08-27 15:31, Pavel Machek wrote:
> Hi!
> 
> On Fri 2018-08-24 15:57:42, Kiran Gunda wrote:
>> Update the bindings with the new properties used for
>> PMI8998.
> 
>> Changes from V3:
>>     - Removed the default values.
> 
> Why?
> 
As per Bjorn's comment I have removed the default values.
Do you want to add them back ?

>> +- qcom,current-limit-microamp
>> +	Usage:        optional
>> +	Value type:   <u32>
>> +	Definition:   uA; per-string current limit; value from 0 to 30000 
>> with
>> +		      2500 uA step.
>> 
>>  - qcom,current-boost-limit
>>  	Usage:        optional
>>  	Value type:   <u32>
>>  	Definition:   mA; boost current limit.
>>  		      For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400,
>> -		      1680. Default: 805 mA
>> +		      1680.
>>  		      For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300,
>> -		      1500. Default: 970 mA
>> +		      1500.
>> 
> 
> I'd say that optional properties should list default values...?
> 
Same as above.

>>  - qcom,ovp
>>  	Usage:        optional
>>  	Value type:   <u32>
>>  	Definition:   V; Over-voltage protection limit; one of:
>> -		      27, 29, 32, 35. default: 29V
>> +		      27, 29, 32, 35.
>>  		      This property is supported only for PM8941.
>> 
> 
> Same here.
> 
Same as above.
>> +- qcom,ovp-millivolt
>> +	Usage:        optional
>> +	Value type:   <u32>
>> +	Definition:   mV; Over-voltage protection limit;
>> +		      For pmi8998: one of 18100, 19600, 29600, 31100
>> +		      If this property is not specified for PM8941, it
>> +		      falls back to "qcom,ovp" property.
>> +
> 
> "voltage-limit-millivolt"? "ovp" is not really well known acronym.
> 									Pavel
"ovp" is already being used in pm8941-wled.c driver. That's why I am 
using ovp-millivolt.
If I rename this, i think I have to rename the existing "qcom,ovp" also, 
which will break
the backward compatibility.
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
index 14f28f2..9d840d5 100644
--- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
+++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
@@ -20,8 +20,7 @@  platforms. The PMIC is connected to the host processor via SPMI bus.
 - default-brightness
 	Usage:        optional
 	Value type:   <u32>
-	Definition:   brightness value on boot, value from: 0-4095
-		      Default: 2048
+	Definition:   brightness value on boot, value from: 0-4095.
 
 - label
 	Usage:        required
@@ -48,20 +47,24 @@  platforms. The PMIC is connected to the host processor via SPMI bus.
 - qcom,current-limit
 	Usage:        optional
 	Value type:   <u32>
-	Definition:   mA; per-string current limit
-		      value: For pm8941: from 0 to 25 with 5 mA step
-			     Default 20 mA.
-			     For pmi8998: from 0 to 30 with 5 mA step
-			     Default 25 mA.
+	Definition:   mA; per-string current limit; value from 0 to 25 with
+		      1 mA step.
+		      This property is supported only for pm8941.
+
+- qcom,current-limit-microamp
+	Usage:        optional
+	Value type:   <u32>
+	Definition:   uA; per-string current limit; value from 0 to 30000 with
+		      2500 uA step.
 
 - qcom,current-boost-limit
 	Usage:        optional
 	Value type:   <u32>
 	Definition:   mA; boost current limit.
 		      For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400,
-		      1680. Default: 805 mA
+		      1680.
 		      For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300,
-		      1500. Default: 970 mA
+		      1500.
 
 - qcom,switching-freq
 	Usage:        optional
@@ -69,22 +72,66 @@  platforms. The PMIC is connected to the host processor via SPMI bus.
 	 Definition:   kHz; switching frequency; one of: 600, 640, 685, 738,
 		       800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200,
 		       4800, 9600.
-		       Default: for pm8941: 1600 kHz
-				for pmi8998: 800 kHz
 
 - qcom,ovp
 	Usage:        optional
 	Value type:   <u32>
 	Definition:   V; Over-voltage protection limit; one of:
-		      27, 29, 32, 35. default: 29V
+		      27, 29, 32, 35.
 		      This property is supported only for PM8941.
 
+- qcom,ovp-millivolt
+	Usage:        optional
+	Value type:   <u32>
+	Definition:   mV; Over-voltage protection limit;
+		      For pmi8998: one of 18100, 19600, 29600, 31100
+		      If this property is not specified for PM8941, it
+		      falls back to "qcom,ovp" property.
+
 - qcom,num-strings
 	Usage:        optional
 	Value type:   <u32>
 	Definition:   #; number of led strings attached;
-		      value from 1 to 3. default: 2
-		      This property is supported only for PM8941.
+		      value: For PM8941 from 1 to 3.
+			     For PMI8998 from 1 to 4.
+
+- interrupts
+	Usage:        optional
+	Value type:   <prop encoded array>
+	Definition:   Interrupts associated with WLED. This should be
+		      "short" and "ovp" interrupts. Interrupts can be
+		      specified as per the encoding listed under
+		      Documentation/devicetree/bindings/spmi/
+		      qcom,spmi-pmic-arb.txt.
+
+- interrupt-names
+	Usage:        optional
+	Value type:   <string>
+	Definition:   Interrupt names associated with the interrupts.
+		      Must be "short" and "ovp". The short circuit detection
+		      is not supported for PM8941.
+
+- qcom,enabled-strings
+	Usage:        optional
+	Value tyoe:   <u32 array>
+	Definition:   Array of the WLED strings numbered from 0 to 3. Each
+		      string of leds are operated individually. Specify the
+		      list of strings used by the device. Any combination of
+		      led strings can be used.
+
+- qcom,external-pfet
+	Usage:        optional
+	Value type:   <bool>
+	Definition:   Specify if external PFET control for short circuit
+		      protection is used. This property is supported only
+		      for PMI8998.
+
+- qcom,auto-string-detection
+	Usage:        optional
+	Value type:   <bool>
+	Definition:   Enables auto-detection of the WLED string configuration.
+		      This feature is not supported for PM8941.
+
 
 Example:
 
@@ -99,4 +146,5 @@  pm8941-wled@d800 {
 	qcom,switching-freq = <1600>;
 	qcom,ovp = <29>;
 	qcom,num-strings = <2>;
+	qcom,enabled-strings = <0 1>;
 };