| Message ID | 20180829110408.556c3622@xhacker.debian (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v3] PCI: dwc: fix scheduling while atomic issues | expand |
Hi all, On Wed, 29 Aug 2018 11:04:08 +0800 Jisheng Zhang wrote: > When programming inbound/outbound atu, we call usleep_range() after > each checking PCIE_ATU_ENABLE bit. Unfortunately, the atu programming > can be called in atomic context: > > inbound atu programming could be called through > pci_epc_write_header() > =>dw_pcie_ep_write_header() > =>dw_pcie_prog_inbound_atu() > > outbound atu programming could be called through > pci_bus_read_config_dword() > =>dw_pcie_rd_conf() > =>dw_pcie_prog_outbound_atu() > > Fix this issue by calling mdelay() instead. Any comments about this patch? Thanks, Jisheng > > Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support") > Fixes: d8bbeb39fbf3 ("PCI: designware: Wait for iATU enable") > Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> > Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> > --- > > since v2: > - Add Fixes tag > - Add Gustavo's Ack > > since v1: > - use mdelay() instead of udelay() to avoid __bad_udelay() > > drivers/pci/controller/dwc/pcie-designware.c | 8 ++++---- > drivers/pci/controller/dwc/pcie-designware.h | 3 +-- > 2 files changed, 5 insertions(+), 6 deletions(-) > > diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c > index 778c4f76a884..2153956a0b20 100644 > --- a/drivers/pci/controller/dwc/pcie-designware.c > +++ b/drivers/pci/controller/dwc/pcie-designware.c > @@ -135,7 +135,7 @@ static void dw_pcie_prog_outbound_atu_unroll(struct dw_pcie *pci, int index, > if (val & PCIE_ATU_ENABLE) > return; > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > + mdelay(LINK_WAIT_IATU); > } > dev_err(pci->dev, "Outbound iATU is not being enabled\n"); > } > @@ -178,7 +178,7 @@ void dw_pcie_prog_outbound_atu(struct dw_pcie *pci, int index, int type, > if (val & PCIE_ATU_ENABLE) > return; > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > + mdelay(LINK_WAIT_IATU); > } > dev_err(pci->dev, "Outbound iATU is not being enabled\n"); > } > @@ -236,7 +236,7 @@ static int dw_pcie_prog_inbound_atu_unroll(struct dw_pcie *pci, int index, > if (val & PCIE_ATU_ENABLE) > return 0; > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > + mdelay(LINK_WAIT_IATU); > } > dev_err(pci->dev, "Inbound iATU is not being enabled\n"); > > @@ -282,7 +282,7 @@ int dw_pcie_prog_inbound_atu(struct dw_pcie *pci, int index, int bar, > if (val & PCIE_ATU_ENABLE) > return 0; > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > + mdelay(LINK_WAIT_IATU); > } > dev_err(pci->dev, "Inbound iATU is not being enabled\n"); > > diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h > index 96126fd8403c..9f1a5e399b70 100644 > --- a/drivers/pci/controller/dwc/pcie-designware.h > +++ b/drivers/pci/controller/dwc/pcie-designware.h > @@ -26,8 +26,7 @@ > > /* Parameters for the waiting for iATU enabled routine */ > #define LINK_WAIT_MAX_IATU_RETRIES 5 > -#define LINK_WAIT_IATU_MIN 9000 > -#define LINK_WAIT_IATU_MAX 10000 > +#define LINK_WAIT_IATU 9 > > /* Synopsys-specific PCIe configuration registers */ > #define PCIE_PORT_LINK_CONTROL 0x710
On Mon, Sep 10, 2018 at 04:57:22PM +0800, Jisheng Zhang wrote: > Hi all, > > On Wed, 29 Aug 2018 11:04:08 +0800 Jisheng Zhang wrote: > > > When programming inbound/outbound atu, we call usleep_range() after > > each checking PCIE_ATU_ENABLE bit. Unfortunately, the atu programming > > can be called in atomic context: > > > > inbound atu programming could be called through > > pci_epc_write_header() > > =>dw_pcie_ep_write_header() > > =>dw_pcie_prog_inbound_atu() > > > > outbound atu programming could be called through > > pci_bus_read_config_dword() > > =>dw_pcie_rd_conf() > > =>dw_pcie_prog_outbound_atu() > > > > Fix this issue by calling mdelay() instead. > > Any comments about this patch? > > Thanks, > Jisheng > > > > > Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support") > > Fixes: d8bbeb39fbf3 ("PCI: designware: Wait for iATU enable") Can you split it into two patches and repost it please ? It will make everyone's life easier to backport it if there is need, I will apply then. Thanks, Lorenzo > > Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> > > Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> > > --- > > > > since v2: > > - Add Fixes tag > > - Add Gustavo's Ack > > > > since v1: > > - use mdelay() instead of udelay() to avoid __bad_udelay() > > > > drivers/pci/controller/dwc/pcie-designware.c | 8 ++++---- > > drivers/pci/controller/dwc/pcie-designware.h | 3 +-- > > 2 files changed, 5 insertions(+), 6 deletions(-) > > > > diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c > > index 778c4f76a884..2153956a0b20 100644 > > --- a/drivers/pci/controller/dwc/pcie-designware.c > > +++ b/drivers/pci/controller/dwc/pcie-designware.c > > @@ -135,7 +135,7 @@ static void dw_pcie_prog_outbound_atu_unroll(struct dw_pcie *pci, int index, > > if (val & PCIE_ATU_ENABLE) > > return; > > > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > > + mdelay(LINK_WAIT_IATU); > > } > > dev_err(pci->dev, "Outbound iATU is not being enabled\n"); > > } > > @@ -178,7 +178,7 @@ void dw_pcie_prog_outbound_atu(struct dw_pcie *pci, int index, int type, > > if (val & PCIE_ATU_ENABLE) > > return; > > > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > > + mdelay(LINK_WAIT_IATU); > > } > > dev_err(pci->dev, "Outbound iATU is not being enabled\n"); > > } > > @@ -236,7 +236,7 @@ static int dw_pcie_prog_inbound_atu_unroll(struct dw_pcie *pci, int index, > > if (val & PCIE_ATU_ENABLE) > > return 0; > > > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > > + mdelay(LINK_WAIT_IATU); > > } > > dev_err(pci->dev, "Inbound iATU is not being enabled\n"); > > > > @@ -282,7 +282,7 @@ int dw_pcie_prog_inbound_atu(struct dw_pcie *pci, int index, int bar, > > if (val & PCIE_ATU_ENABLE) > > return 0; > > > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > > + mdelay(LINK_WAIT_IATU); > > } > > dev_err(pci->dev, "Inbound iATU is not being enabled\n"); > > > > diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h > > index 96126fd8403c..9f1a5e399b70 100644 > > --- a/drivers/pci/controller/dwc/pcie-designware.h > > +++ b/drivers/pci/controller/dwc/pcie-designware.h > > @@ -26,8 +26,7 @@ > > > > /* Parameters for the waiting for iATU enabled routine */ > > #define LINK_WAIT_MAX_IATU_RETRIES 5 > > -#define LINK_WAIT_IATU_MIN 9000 > > -#define LINK_WAIT_IATU_MAX 10000 > > +#define LINK_WAIT_IATU 9 > > > > /* Synopsys-specific PCIe configuration registers */ > > #define PCIE_PORT_LINK_CONTROL 0x710 >
Hi Lorenzo, On Thu, 13 Sep 2018 10:15:34 +0100 Lorenzo Pieralisi wrote: > On Mon, Sep 10, 2018 at 04:57:22PM +0800, Jisheng Zhang wrote: > > Hi all, > > > > On Wed, 29 Aug 2018 11:04:08 +0800 Jisheng Zhang wrote: > > > > > When programming inbound/outbound atu, we call usleep_range() after > > > each checking PCIE_ATU_ENABLE bit. Unfortunately, the atu programming > > > can be called in atomic context: > > > > > > inbound atu programming could be called through > > > pci_epc_write_header() > > > =>dw_pcie_ep_write_header() > > > =>dw_pcie_prog_inbound_atu() > > > > > > outbound atu programming could be called through > > > pci_bus_read_config_dword() > > > =>dw_pcie_rd_conf() > > > =>dw_pcie_prog_outbound_atu() > > > > > > Fix this issue by calling mdelay() instead. > > > > Any comments about this patch? > > > > Thanks, > > Jisheng > > > > > > > > Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support") > > > Fixes: d8bbeb39fbf3 ("PCI: designware: Wait for iATU enable") > > Can you split it into two patches and repost it please ? It will make > everyone's life easier to backport it if there is need, I will apply > then. IIUC, the purpose of this split is to make the backport to stable easier. If so, I realise that the Fixes tags were not enough, we missed: Fixes: edd45e396829 ("PCI: dwc: designware: Move _unroll configurations to a separate function") I'm not sure how to handle this case. From another side, the issue to be fixed is the same: call sleep in atomic context in the same driver, is it better to use one patch? As for stable tree, I could send out separate patches instead. What do you think? Thanks, Jisheng
On Thu, Sep 13, 2018 at 06:29:54PM +0800, Jisheng Zhang wrote: > Hi Lorenzo, > > On Thu, 13 Sep 2018 10:15:34 +0100 Lorenzo Pieralisi wrote: > > > On Mon, Sep 10, 2018 at 04:57:22PM +0800, Jisheng Zhang wrote: > > > Hi all, > > > > > > On Wed, 29 Aug 2018 11:04:08 +0800 Jisheng Zhang wrote: > > > > > > > When programming inbound/outbound atu, we call usleep_range() after > > > > each checking PCIE_ATU_ENABLE bit. Unfortunately, the atu programming > > > > can be called in atomic context: > > > > > > > > inbound atu programming could be called through > > > > pci_epc_write_header() > > > > =>dw_pcie_ep_write_header() > > > > =>dw_pcie_prog_inbound_atu() > > > > > > > > outbound atu programming could be called through > > > > pci_bus_read_config_dword() > > > > =>dw_pcie_rd_conf() > > > > =>dw_pcie_prog_outbound_atu() > > > > > > > > Fix this issue by calling mdelay() instead. > > > > > > Any comments about this patch? > > > > > > Thanks, > > > Jisheng > > > > > > > > > > > Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support") > > > > Fixes: d8bbeb39fbf3 ("PCI: designware: Wait for iATU enable") > > > > Can you split it into two patches and repost it please ? It will make > > everyone's life easier to backport it if there is need, I will apply > > then. > > IIUC, the purpose of this split is to make the backport to stable easier. If > so, I realise that the Fixes tags were not enough, we missed: > > Fixes: edd45e396829 ("PCI: dwc: designware: Move _unroll configurations to a > separate function") > > I'm not sure how to handle this case. From another side, the issue to be > fixed is the same: call sleep in atomic context in the same driver, is it > better to use one patch? > > As for stable tree, I could send out separate patches instead. What do you > think? OK, I will merge the patch as-is and we will handle the stable backports when Greg sends the patches out. Lorenzo
On Wed, Aug 29, 2018 at 11:04:08AM +0800, Jisheng Zhang wrote: > When programming inbound/outbound atu, we call usleep_range() after > each checking PCIE_ATU_ENABLE bit. Unfortunately, the atu programming > can be called in atomic context: > > inbound atu programming could be called through > pci_epc_write_header() > =>dw_pcie_ep_write_header() > =>dw_pcie_prog_inbound_atu() > > outbound atu programming could be called through > pci_bus_read_config_dword() > =>dw_pcie_rd_conf() > =>dw_pcie_prog_outbound_atu() > > Fix this issue by calling mdelay() instead. > > Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support") > Fixes: d8bbeb39fbf3 ("PCI: designware: Wait for iATU enable") > Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> > Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> > --- Applied to pci/controller-fixes aiming at one of the upcoming -rc*. Thanks, Lorenzo > since v2: > - Add Fixes tag > - Add Gustavo's Ack > > since v1: > - use mdelay() instead of udelay() to avoid __bad_udelay() > > drivers/pci/controller/dwc/pcie-designware.c | 8 ++++---- > drivers/pci/controller/dwc/pcie-designware.h | 3 +-- > 2 files changed, 5 insertions(+), 6 deletions(-) > > diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c > index 778c4f76a884..2153956a0b20 100644 > --- a/drivers/pci/controller/dwc/pcie-designware.c > +++ b/drivers/pci/controller/dwc/pcie-designware.c > @@ -135,7 +135,7 @@ static void dw_pcie_prog_outbound_atu_unroll(struct dw_pcie *pci, int index, > if (val & PCIE_ATU_ENABLE) > return; > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > + mdelay(LINK_WAIT_IATU); > } > dev_err(pci->dev, "Outbound iATU is not being enabled\n"); > } > @@ -178,7 +178,7 @@ void dw_pcie_prog_outbound_atu(struct dw_pcie *pci, int index, int type, > if (val & PCIE_ATU_ENABLE) > return; > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > + mdelay(LINK_WAIT_IATU); > } > dev_err(pci->dev, "Outbound iATU is not being enabled\n"); > } > @@ -236,7 +236,7 @@ static int dw_pcie_prog_inbound_atu_unroll(struct dw_pcie *pci, int index, > if (val & PCIE_ATU_ENABLE) > return 0; > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > + mdelay(LINK_WAIT_IATU); > } > dev_err(pci->dev, "Inbound iATU is not being enabled\n"); > > @@ -282,7 +282,7 @@ int dw_pcie_prog_inbound_atu(struct dw_pcie *pci, int index, int bar, > if (val & PCIE_ATU_ENABLE) > return 0; > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > + mdelay(LINK_WAIT_IATU); > } > dev_err(pci->dev, "Inbound iATU is not being enabled\n"); > > diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h > index 96126fd8403c..9f1a5e399b70 100644 > --- a/drivers/pci/controller/dwc/pcie-designware.h > +++ b/drivers/pci/controller/dwc/pcie-designware.h > @@ -26,8 +26,7 @@ > > /* Parameters for the waiting for iATU enabled routine */ > #define LINK_WAIT_MAX_IATU_RETRIES 5 > -#define LINK_WAIT_IATU_MIN 9000 > -#define LINK_WAIT_IATU_MAX 10000 > +#define LINK_WAIT_IATU 9 > > /* Synopsys-specific PCIe configuration registers */ > #define PCIE_PORT_LINK_CONTROL 0x710 > -- > 2.18.0 >
On Thu, Sep 13, 2018 at 04:05:54PM +0100, Lorenzo Pieralisi wrote: > On Wed, Aug 29, 2018 at 11:04:08AM +0800, Jisheng Zhang wrote: > > When programming inbound/outbound atu, we call usleep_range() after > > each checking PCIE_ATU_ENABLE bit. Unfortunately, the atu programming > > can be called in atomic context: > > > > inbound atu programming could be called through > > pci_epc_write_header() > > =>dw_pcie_ep_write_header() > > =>dw_pcie_prog_inbound_atu() > > > > outbound atu programming could be called through > > pci_bus_read_config_dword() > > =>dw_pcie_rd_conf() > > =>dw_pcie_prog_outbound_atu() > > > > Fix this issue by calling mdelay() instead. > > > > Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support") > > Fixes: d8bbeb39fbf3 ("PCI: designware: Wait for iATU enable") > > Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> > > Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> > > --- > > Applied to pci/controller-fixes aiming at one of the upcoming -rc*. I cherry-picked this into for-linus for v4.19. > > since v2: > > - Add Fixes tag > > - Add Gustavo's Ack > > > > since v1: > > - use mdelay() instead of udelay() to avoid __bad_udelay() > > > > drivers/pci/controller/dwc/pcie-designware.c | 8 ++++---- > > drivers/pci/controller/dwc/pcie-designware.h | 3 +-- > > 2 files changed, 5 insertions(+), 6 deletions(-) > > > > diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c > > index 778c4f76a884..2153956a0b20 100644 > > --- a/drivers/pci/controller/dwc/pcie-designware.c > > +++ b/drivers/pci/controller/dwc/pcie-designware.c > > @@ -135,7 +135,7 @@ static void dw_pcie_prog_outbound_atu_unroll(struct dw_pcie *pci, int index, > > if (val & PCIE_ATU_ENABLE) > > return; > > > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > > + mdelay(LINK_WAIT_IATU); > > } > > dev_err(pci->dev, "Outbound iATU is not being enabled\n"); > > } > > @@ -178,7 +178,7 @@ void dw_pcie_prog_outbound_atu(struct dw_pcie *pci, int index, int type, > > if (val & PCIE_ATU_ENABLE) > > return; > > > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > > + mdelay(LINK_WAIT_IATU); > > } > > dev_err(pci->dev, "Outbound iATU is not being enabled\n"); > > } > > @@ -236,7 +236,7 @@ static int dw_pcie_prog_inbound_atu_unroll(struct dw_pcie *pci, int index, > > if (val & PCIE_ATU_ENABLE) > > return 0; > > > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > > + mdelay(LINK_WAIT_IATU); > > } > > dev_err(pci->dev, "Inbound iATU is not being enabled\n"); > > > > @@ -282,7 +282,7 @@ int dw_pcie_prog_inbound_atu(struct dw_pcie *pci, int index, int bar, > > if (val & PCIE_ATU_ENABLE) > > return 0; > > > > - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); > > + mdelay(LINK_WAIT_IATU); > > } > > dev_err(pci->dev, "Inbound iATU is not being enabled\n"); > > > > diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h > > index 96126fd8403c..9f1a5e399b70 100644 > > --- a/drivers/pci/controller/dwc/pcie-designware.h > > +++ b/drivers/pci/controller/dwc/pcie-designware.h > > @@ -26,8 +26,7 @@ > > > > /* Parameters for the waiting for iATU enabled routine */ > > #define LINK_WAIT_MAX_IATU_RETRIES 5 > > -#define LINK_WAIT_IATU_MIN 9000 > > -#define LINK_WAIT_IATU_MAX 10000 > > +#define LINK_WAIT_IATU 9 > > > > /* Synopsys-specific PCIe configuration registers */ > > #define PCIE_PORT_LINK_CONTROL 0x710 > > -- > > 2.18.0 > > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c index 778c4f76a884..2153956a0b20 100644 --- a/drivers/pci/controller/dwc/pcie-designware.c +++ b/drivers/pci/controller/dwc/pcie-designware.c @@ -135,7 +135,7 @@ static void dw_pcie_prog_outbound_atu_unroll(struct dw_pcie *pci, int index, if (val & PCIE_ATU_ENABLE) return; - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); + mdelay(LINK_WAIT_IATU); } dev_err(pci->dev, "Outbound iATU is not being enabled\n"); } @@ -178,7 +178,7 @@ void dw_pcie_prog_outbound_atu(struct dw_pcie *pci, int index, int type, if (val & PCIE_ATU_ENABLE) return; - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); + mdelay(LINK_WAIT_IATU); } dev_err(pci->dev, "Outbound iATU is not being enabled\n"); } @@ -236,7 +236,7 @@ static int dw_pcie_prog_inbound_atu_unroll(struct dw_pcie *pci, int index, if (val & PCIE_ATU_ENABLE) return 0; - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); + mdelay(LINK_WAIT_IATU); } dev_err(pci->dev, "Inbound iATU is not being enabled\n"); @@ -282,7 +282,7 @@ int dw_pcie_prog_inbound_atu(struct dw_pcie *pci, int index, int bar, if (val & PCIE_ATU_ENABLE) return 0; - usleep_range(LINK_WAIT_IATU_MIN, LINK_WAIT_IATU_MAX); + mdelay(LINK_WAIT_IATU); } dev_err(pci->dev, "Inbound iATU is not being enabled\n"); diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h index 96126fd8403c..9f1a5e399b70 100644 --- a/drivers/pci/controller/dwc/pcie-designware.h +++ b/drivers/pci/controller/dwc/pcie-designware.h @@ -26,8 +26,7 @@ /* Parameters for the waiting for iATU enabled routine */ #define LINK_WAIT_MAX_IATU_RETRIES 5 -#define LINK_WAIT_IATU_MIN 9000 -#define LINK_WAIT_IATU_MAX 10000 +#define LINK_WAIT_IATU 9 /* Synopsys-specific PCIe configuration registers */ #define PCIE_PORT_LINK_CONTROL 0x710
When programming inbound/outbound atu, we call usleep_range() after each checking PCIE_ATU_ENABLE bit. Unfortunately, the atu programming can be called in atomic context: inbound atu programming could be called through pci_epc_write_header() =>dw_pcie_ep_write_header() =>dw_pcie_prog_inbound_atu() outbound atu programming could be called through pci_bus_read_config_dword() =>dw_pcie_rd_conf() =>dw_pcie_prog_outbound_atu() Fix this issue by calling mdelay() instead. Fixes: f8aed6ec624f ("PCI: dwc: designware: Add EP mode support") Fixes: d8bbeb39fbf3 ("PCI: designware: Wait for iATU enable") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> --- since v2: - Add Fixes tag - Add Gustavo's Ack since v1: - use mdelay() instead of udelay() to avoid __bad_udelay() drivers/pci/controller/dwc/pcie-designware.c | 8 ++++---- drivers/pci/controller/dwc/pcie-designware.h | 3 +-- 2 files changed, 5 insertions(+), 6 deletions(-)