diff mbox series

[v4,2/2] mtd: rawnand: meson: add support for Amlogic NAND flash controller

Message ID 1537433449-65213-3-git-send-email-jianxin.pan@amlogic.com (mailing list archive)
State Not Applicable
Headers show
Series mtd: rawnand: meson: add Amlogic NAND driver support | expand

Commit Message

Jianxin Pan Sept. 20, 2018, 8:50 a.m. UTC
From: Liang Yang <liang.yang@amlogic.com>

Add initial support for the Amlogic NAND flash controller which found
in the Meson-GXBB/GXL/AXG SoCs.

Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
---
 drivers/mtd/nand/raw/Kconfig      |   10 +
 drivers/mtd/nand/raw/Makefile     |    1 +
 drivers/mtd/nand/raw/meson_nand.c | 1372 +++++++++++++++++++++++++++++++++++++
 3 files changed, 1383 insertions(+)
 create mode 100644 drivers/mtd/nand/raw/meson_nand.c

Comments

Martin Blumenstingl Sept. 22, 2018, 3:32 p.m. UTC | #1
Hello,

On Thu, Sep 20, 2018 at 10:51 AM Jianxin Pan <jianxin.pan@amlogic.com> wrote:
[snip]
> +static int meson_nfc_clk_init(struct meson_nfc *nfc)
> +{
> +       int ret;
> +
> +       /* request core clock */
> +       nfc->core_clk = devm_clk_get(nfc->dev, "core");
> +       if (IS_ERR(nfc->core_clk)) {
> +               dev_err(nfc->dev, "failed to get core clk\n");
> +               return PTR_ERR(nfc->core_clk);
> +       }
> +
> +       nfc->device_clk = devm_clk_get(nfc->dev, "device");
> +       if (IS_ERR(nfc->device_clk)) {
> +               dev_err(nfc->dev, "failed to get device clk\n");
> +               return PTR_ERR(nfc->device_clk);
> +       }
> +
> +       nfc->phase_tx = devm_clk_get(nfc->dev, "tx");
> +       if (IS_ERR(nfc->phase_tx)) {
> +               dev_err(nfc->dev, "failed to get tx clk\n");
> +               return PTR_ERR(nfc->phase_tx);
> +       }
> +
> +       nfc->phase_rx = devm_clk_get(nfc->dev, "rx");
> +       if (IS_ERR(nfc->phase_rx)) {
> +               dev_err(nfc->dev, "failed to get rx clk\n");
> +               return PTR_ERR(nfc->phase_rx);
> +       }
neither the "rx" nor the "tx" clock are documented in the dt-bindings patch

> +       /* init SD_EMMC_CLOCK to sane defaults w/min clock rate */
> +       regmap_update_bits(nfc->reg_clk, 0,
> +                          CLK_SELECT_NAND | CLK_ALWAYS_ON | CLK_DIV_MASK,
> +                          CLK_SELECT_NAND | CLK_ALWAYS_ON | CLK_DIV_MASK);
clk_set_rate also works for clocks that are not enabled yet (except if
they have the flag CLK_SET_RATE_UNGATE)
this should help you to remove CLK_DIV_MASK here

is CLK_SELECT_NAND a bit that switches the clock output from the sdmmc
controller to the NAND controller?
if so: can this be modeled as a mux clock?

the public S905 datasheet doesn't mention CLK_ALWAYS_ON at bit 28 but
uses bit 24 instead. the description from the datasheet:
Cfg_always_on:
1: Keep clock always on
0: Clock on/off controlled by activities.
    Any APB3 access or descriptor execution will turn clock on.
Recommended value: 0

can you please explain what CLK_ALWAYS_ON does and why it has to be 1?


Regards
Martin
Liang Yang Sept. 27, 2018, 8:16 a.m. UTC | #2
Hello Martin,

On 9/22/2018 11:32 PM, Martin Blumenstingl wrote:
> Hello,
> 
> On Thu, Sep 20, 2018 at 10:51 AM Jianxin Pan <jianxin.pan@amlogic.com> wrote:
> [snip]
>> +static int meson_nfc_clk_init(struct meson_nfc *nfc)
>> +{
>> +       int ret;
>> +
>> +       /* request core clock */
>> +       nfc->core_clk = devm_clk_get(nfc->dev, "core");
>> +       if (IS_ERR(nfc->core_clk)) {
>> +               dev_err(nfc->dev, "failed to get core clk\n");
>> +               return PTR_ERR(nfc->core_clk);
>> +       }
>> +
>> +       nfc->device_clk = devm_clk_get(nfc->dev, "device");
>> +       if (IS_ERR(nfc->device_clk)) {
>> +               dev_err(nfc->dev, "failed to get device clk\n");
>> +               return PTR_ERR(nfc->device_clk);
>> +       }
>> +
>> +       nfc->phase_tx = devm_clk_get(nfc->dev, "tx");
>> +       if (IS_ERR(nfc->phase_tx)) {
>> +               dev_err(nfc->dev, "failed to get tx clk\n");
>> +               return PTR_ERR(nfc->phase_tx);
>> +       }
>> +
>> +       nfc->phase_rx = devm_clk_get(nfc->dev, "rx");
>> +       if (IS_ERR(nfc->phase_rx)) {
>> +               dev_err(nfc->dev, "failed to get rx clk\n");
>> +               return PTR_ERR(nfc->phase_rx);
>> +       }
> neither the "rx" nor the "tx" clock are documented in the dt-bindings patch
> 

ok, i will add them later.

>> +       /* init SD_EMMC_CLOCK to sane defaults w/min clock rate */
>> +       regmap_update_bits(nfc->reg_clk, 0,
>> +                          CLK_SELECT_NAND | CLK_ALWAYS_ON | CLK_DIV_MASK,
>> +                          CLK_SELECT_NAND | CLK_ALWAYS_ON | CLK_DIV_MASK);
> clk_set_rate also works for clocks that are not enabled yet (except if
> they have the flag CLK_SET_RATE_UNGATE)
> this should help you to remove CLK_DIV_MASK here
> 

if not set clk_div_mask here, the value 0x00 of divider means nand clock 
off, even read/write nand register is forbidden.

> is CLK_SELECT_NAND a bit that switches the clock output from the sdmmc
> controller to the NAND controller?
> if so: can this be modeled as a mux clock?
> 

it seems to like a gate. 1: nand is selected; 0: emmc is selected.
Is it suitable for making it as a mux clock?

> the public S905 datasheet doesn't mention CLK_ALWAYS_ON at bit 28 but
> uses bit 24 instead. the description from the datasheet:
> Cfg_always_on:
> 1: Keep clock always on
> 0: Clock on/off controlled by activities.
>      Any APB3 access or descriptor execution will turn clock on.
> Recommended value: 0
> 
> can you please explain what CLK_ALWAYS_ON does and why it has to be 1?
> 

em , it is the same as bit 24 in S905 datasheet, only moves to bit 28.
it means keeping internal clock on whether nand wroks or not.
it doesn't have to be 1; i have tried 0 successfully on AXG platform.

> 
> Regards
> Martin
> 
> .
>
Martin Blumenstingl Sept. 27, 2018, 9:12 a.m. UTC | #3
Hello Liang,

On Thu, Sep 27, 2018 at 10:19 AM Liang Yang <liang.yang@amlogic.com> wrote:
>
> Hello Martin,
>
> On 9/22/2018 11:32 PM, Martin Blumenstingl wrote:
> > Hello,
> >
> > On Thu, Sep 20, 2018 at 10:51 AM Jianxin Pan <jianxin.pan@amlogic.com> wrote:
> > [snip]
> >> +static int meson_nfc_clk_init(struct meson_nfc *nfc)
> >> +{
> >> +       int ret;
> >> +
> >> +       /* request core clock */
> >> +       nfc->core_clk = devm_clk_get(nfc->dev, "core");
> >> +       if (IS_ERR(nfc->core_clk)) {
> >> +               dev_err(nfc->dev, "failed to get core clk\n");
> >> +               return PTR_ERR(nfc->core_clk);
> >> +       }
> >> +
> >> +       nfc->device_clk = devm_clk_get(nfc->dev, "device");
> >> +       if (IS_ERR(nfc->device_clk)) {
> >> +               dev_err(nfc->dev, "failed to get device clk\n");
> >> +               return PTR_ERR(nfc->device_clk);
> >> +       }
> >> +
> >> +       nfc->phase_tx = devm_clk_get(nfc->dev, "tx");
> >> +       if (IS_ERR(nfc->phase_tx)) {
> >> +               dev_err(nfc->dev, "failed to get tx clk\n");
> >> +               return PTR_ERR(nfc->phase_tx);
> >> +       }
> >> +
> >> +       nfc->phase_rx = devm_clk_get(nfc->dev, "rx");
> >> +       if (IS_ERR(nfc->phase_rx)) {
> >> +               dev_err(nfc->dev, "failed to get rx clk\n");
> >> +               return PTR_ERR(nfc->phase_rx);
> >> +       }
> > neither the "rx" nor the "tx" clock are documented in the dt-bindings patch
> >
>
> ok, i will add them later.
>
> >> +       /* init SD_EMMC_CLOCK to sane defaults w/min clock rate */
> >> +       regmap_update_bits(nfc->reg_clk, 0,
> >> +                          CLK_SELECT_NAND | CLK_ALWAYS_ON | CLK_DIV_MASK,
> >> +                          CLK_SELECT_NAND | CLK_ALWAYS_ON | CLK_DIV_MASK);
> > clk_set_rate also works for clocks that are not enabled yet (except if
> > they have the flag CLK_SET_RATE_UNGATE)
> > this should help you to remove CLK_DIV_MASK here
> >
>
> if not set clk_div_mask here, the value 0x00 of divider means nand clock
> off, even read/write nand register is forbidden.
ah, now I see the pattern here.
Jerome has written a "sclk-div" driver (which is currently only used
for the audio clocks on AXG). based on reading the code it seems that
switching the driver of the divider clock to sclk-div would allow you
to remove setting CLK_DIV_MASK here:
- the  "hi" parameter in struct meson_sclk_div_data is optional ->
then the sclk-div clock won't try to change the duty cycle
- sclk_div_init reads the divider at initialization time - if it's 0
it takes the maximum possible divider value
- sclk_div_enable (which you're going to call anyways, through
clk_prepare_enable) will then set the divider to the greatest possible
value

> > is CLK_SELECT_NAND a bit that switches the clock output from the sdmmc
> > controller to the NAND controller?
> > if so: can this be modeled as a mux clock?
> >
>
> it seems to like a gate. 1: nand is selected; 0: emmc is selected.
> Is it suitable for making it as a mux clock?
my understanding of a gate is:
- register value X = OFF, value Y = ON

but in your case it's:
- 0 = eMMC is ON but NAND is OFF
- 1 = eMMC is OFF but NAND is ON
(so both values mean "on", just for different contexts)

I believe you need to set this value for eMMC as well:
what if the bootloader (or hardware defaults, etc.) incorrectly sets
the value to 1 but the Linux .dts is configured to use eMMC?

> > the public S905 datasheet doesn't mention CLK_ALWAYS_ON at bit 28 but
> > uses bit 24 instead. the description from the datasheet:
> > Cfg_always_on:
> > 1: Keep clock always on
> > 0: Clock on/off controlled by activities.
> >      Any APB3 access or descriptor execution will turn clock on.
> > Recommended value: 0
> >
> > can you please explain what CLK_ALWAYS_ON does and why it has to be 1?
> >
>
> em , it is the same as bit 24 in S905 datasheet, only moves to bit 28.
> it means keeping internal clock on whether nand wroks or not.
> it doesn't have to be 1; i have tried 0 successfully on AXG platform.
my preference would be to use the recommended value from the datasheet
unless there's a good argument why it has to be different


Regards
Martin
Liang Yang Sept. 28, 2018, 8:31 a.m. UTC | #4
On 9/27/2018 5:12 PM, Martin Blumenstingl wrote:
> Hello Liang,
> 
> On Thu, Sep 27, 2018 at 10:19 AM Liang Yang <liang.yang@amlogic.com> wrote:
>>
>> Hello Martin,
>>
>> On 9/22/2018 11:32 PM, Martin Blumenstingl wrote:
>>> Hello,
>>>
>>> On Thu, Sep 20, 2018 at 10:51 AM Jianxin Pan <jianxin.pan@amlogic.com> wrote:
>>> [snip]
>>>> +static int meson_nfc_clk_init(struct meson_nfc *nfc)
>>>> +{
>>>> +       int ret;
>>>> +
>>>> +       /* request core clock */
>>>> +       nfc->core_clk = devm_clk_get(nfc->dev, "core");
>>>> +       if (IS_ERR(nfc->core_clk)) {
>>>> +               dev_err(nfc->dev, "failed to get core clk\n");
>>>> +               return PTR_ERR(nfc->core_clk);
>>>> +       }
>>>> +
>>>> +       nfc->device_clk = devm_clk_get(nfc->dev, "device");
>>>> +       if (IS_ERR(nfc->device_clk)) {
>>>> +               dev_err(nfc->dev, "failed to get device clk\n");
>>>> +               return PTR_ERR(nfc->device_clk);
>>>> +       }
>>>> +
>>>> +       nfc->phase_tx = devm_clk_get(nfc->dev, "tx");
>>>> +       if (IS_ERR(nfc->phase_tx)) {
>>>> +               dev_err(nfc->dev, "failed to get tx clk\n");
>>>> +               return PTR_ERR(nfc->phase_tx);
>>>> +       }
>>>> +
>>>> +       nfc->phase_rx = devm_clk_get(nfc->dev, "rx");
>>>> +       if (IS_ERR(nfc->phase_rx)) {
>>>> +               dev_err(nfc->dev, "failed to get rx clk\n");
>>>> +               return PTR_ERR(nfc->phase_rx);
>>>> +       }
>>> neither the "rx" nor the "tx" clock are documented in the dt-bindings patch
>>>
>>
>> ok, i will add them later.
>>
>>>> +       /* init SD_EMMC_CLOCK to sane defaults w/min clock rate */
>>>> +       regmap_update_bits(nfc->reg_clk, 0,
>>>> +                          CLK_SELECT_NAND | CLK_ALWAYS_ON | CLK_DIV_MASK,
>>>> +                          CLK_SELECT_NAND | CLK_ALWAYS_ON | CLK_DIV_MASK);
>>> clk_set_rate also works for clocks that are not enabled yet (except if
>>> they have the flag CLK_SET_RATE_UNGATE)
>>> this should help you to remove CLK_DIV_MASK here
>>>
>>
>> if not set clk_div_mask here, the value 0x00 of divider means nand clock
>> off, even read/write nand register is forbidden.
> ah, now I see the pattern here.
> Jerome has written a "sclk-div" driver (which is currently only used
> for the audio clocks on AXG). based on reading the code it seems that
> switching the driver of the divider clock to sclk-div would allow you
> to remove setting CLK_DIV_MASK here:
> - the  "hi" parameter in struct meson_sclk_div_data is optional ->
> then the sclk-div clock won't try to change the duty cycle
> - sclk_div_init reads the divider at initialization time - if it's 0
> it takes the maximum possible divider value
> - sclk_div_enable (which you're going to call anyways, through
> clk_prepare_enable) will then set the divider to the greatest possible
> value
> 
I read the code and it makes sense.
I try ro add mmc_clkc_regmap_divider_ops in clk-regmap.c and implement 
the initial value when enable call. like this:
+static int mmc_clkc_regmap_div_enable(struct clk_hw *hw)
+{
+       struct clk_regmap *clk = to_clk_regmap(hw);
+       struct clk_regmap_div_data *div = clk_get_regmap_div_data(clk);
+       unsigned int val;
+
+       regmap_read(clk->map, div->offset, &val);
+       val &= clk_div_mask(div->width);
+       if (!val)
+               regmap_update_bits(clk->map, div->offset,
+                                  clk_div_mask(div->width) << div->shift,
+                                  clk_div_mask(div->width));

+       return 0;
+}

it works.

>>> is CLK_SELECT_NAND a bit that switches the clock output from the sdmmc
>>> controller to the NAND controller?
>>> if so: can this be modeled as a mux clock?
>>>
>>
>> it seems to like a gate. 1: nand is selected; 0: emmc is selected.
>> Is it suitable for making it as a mux clock?
> my understanding of a gate is:
> - register value X = OFF, value Y = ON
> 
> but in your case it's:
> - 0 = eMMC is ON but NAND is OFF
> - 1 = eMMC is OFF but NAND is ON
> (so both values mean "on", just for different contexts)
> 
> I believe you need to set this value for eMMC as well:
> what if the bootloader (or hardware defaults, etc.) incorrectly sets
> the value to 1 but the Linux .dts is configured to use eMMC?
> 
en , we need set 0 for emmc as well.

>>> the public S905 datasheet doesn't mention CLK_ALWAYS_ON at bit 28 but
>>> uses bit 24 instead. the description from the datasheet:
>>> Cfg_always_on:
>>> 1: Keep clock always on
>>> 0: Clock on/off controlled by activities.
>>>       Any APB3 access or descriptor execution will turn clock on.
>>> Recommended value: 0
>>>
>>> can you please explain what CLK_ALWAYS_ON does and why it has to be 1?
>>>
>>
>> em , it is the same as bit 24 in S905 datasheet, only moves to bit 28.
>> it means keeping internal clock on whether nand wroks or not.
>> it doesn't have to be 1; i have tried 0 successfully on AXG platform.
> my preference would be to use the recommended value from the datasheet
> unless there's a good argument why it has to be different
> 
>
indeed, i will adopt the recommended value.

> Regards
> Martin
> 
> .
>
Miquel Raynal Oct. 29, 2018, 9:47 a.m. UTC | #5
Hi Jianxin,

Jianxin Pan <jianxin.pan@amlogic.com> wrote
on Thu, 20 Sep 2018 16:50:49 +0800:

> From: Liang Yang <liang.yang@amlogic.com>
> 
> Add initial support for the Amlogic NAND flash controller which found
> in the Meson-GXBB/GXL/AXG SoCs.
> 
> Signed-off-by: Liang Yang <liang.yang@amlogic.com>
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
> ---

I lost track of what's ongoing there, can you remind me the status of
the whole clk/nand series?

If the clock driver is ready, can you resend the NAND controller driver
please? IIRC it was in a pretty good shape already.

Thanks,
Miquèl
Jianxin Pan Oct. 29, 2018, 11:09 a.m. UTC | #6
Hi Miquel,

On 2018/10/29 17:47, Miquel Raynal wrote:
> Hi Jianxin,
> 
> Jianxin Pan <jianxin.pan@amlogic.com> wrote
> on Thu, 20 Sep 2018 16:50:49 +0800:
> 
>> From: Liang Yang <liang.yang@amlogic.com>
>>
>> Add initial support for the Amlogic NAND flash controller which found
>> in the Meson-GXBB/GXL/AXG SoCs.
>>
>> Signed-off-by: Liang Yang <liang.yang@amlogic.com>
>> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
>> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
>> ---
> 
> I lost track of what's ongoing there, can you remind me the status of
> the whole clk/nand series?
> 
> If the clock driver is ready, can you resend the NAND controller driver
> please? IIRC it was in a pretty good shape already.
>
We got some suggestions about the clock driver, and we are preparing for the next version.
I will resend it soon.
Thank you.
 

> Thanks,
> Miquèl
> 
> .
>
diff mbox series

Patch

diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index 5fc9a1b..b3ea0d6 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -561,4 +561,14 @@  config MTD_NAND_TEGRA
 	  is supported. Extra OOB bytes when using HW ECC are currently
 	  not supported.
 
+config MTD_NAND_MESON
+	tristate "Support for NAND controller on Amlogic's Meson SoCs"
+	depends on ARCH_MESON || COMPILE_TEST
+	depends on COMMON_CLK_AMLOGIC
+	select COMMON_CLK_REGMAP_MESON
+	select MFD_SYSCON
+	help
+	  Enables support for NAND controller on Amlogic's Meson SoCs.
+	  This controller is found on Meson GXBB, GXL, AXG SoCs.
+
 endif # MTD_NAND
diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
index d5a5f98..53abc43 100644
--- a/drivers/mtd/nand/raw/Makefile
+++ b/drivers/mtd/nand/raw/Makefile
@@ -57,6 +57,7 @@  obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand/
 obj-$(CONFIG_MTD_NAND_QCOM)		+= qcom_nandc.o
 obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_ecc.o mtk_nand.o
 obj-$(CONFIG_MTD_NAND_TEGRA)		+= tegra_nand.o
+obj-$(CONFIG_MTD_NAND_MESON)		+= meson_nand.o
 
 nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
 nand-objs += nand_amd.o
diff --git a/drivers/mtd/nand/raw/meson_nand.c b/drivers/mtd/nand/raw/meson_nand.c
new file mode 100644
index 0000000..74ba2fa
--- /dev/null
+++ b/drivers/mtd/nand/raw/meson_nand.c
@@ -0,0 +1,1372 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Amlogic Meson Nand Flash Controller Driver
+ *
+ * Copyright (c) 2018 Amlogic, inc.
+ * Author: Liang Yang <liang.yang@amlogic.com>
+ */
+
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/clk.h>
+#include <linux/mtd/rawnand.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/iopoll.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+
+#define NFC_REG_CMD		0x00
+#define NFC_CMD_DRD		(0x8 << 14)
+#define NFC_CMD_IDLE		(0xc << 14)
+#define NFC_CMD_DWR		(0x4 << 14)
+#define NFC_CMD_CLE		(0x5 << 14)
+#define NFC_CMD_ALE		(0x6 << 14)
+#define NFC_CMD_ADL		((0 << 16) | (3 << 20))
+#define NFC_CMD_ADH		((1 << 16) | (3 << 20))
+#define NFC_CMD_AIL		((2 << 16) | (3 << 20))
+#define NFC_CMD_AIH		((3 << 16) | (3 << 20))
+#define NFC_CMD_SEED		((8 << 16) | (3 << 20))
+#define NFC_CMD_M2N		((0 << 17) | (2 << 20))
+#define NFC_CMD_N2M		((1 << 17) | (2 << 20))
+#define NFC_CMD_RB		BIT(20)
+#define NFC_CMD_IO6		((0xb << 10) | (1 << 18))
+
+#define NFC_REG_CFG		0x04
+#define NFC_REG_DADR		0x08
+#define NFC_REG_IADR		0x0c
+#define NFC_REG_BUF		0x10
+#define NFC_REG_INFO		0x14
+#define NFC_REG_DC		0x18
+#define NFC_REG_ADR		0x1c
+#define NFC_REG_DL		0x20
+#define NFC_REG_DH		0x24
+#define NFC_REG_CADR		0x28
+#define NFC_REG_SADR		0x2c
+#define NFC_REG_PINS		0x30
+#define NFC_REG_VER		0x38
+
+#define NFC_RB_IRQ_EN		BIT(21)
+#define NFC_INT_MASK		(3 << 20)
+
+#define CMDRWGEN(cmd_dir, ran, bch, short_mode, page_size, pages)	\
+	(								\
+		(cmd_dir)			|			\
+		((ran) << 19)			|			\
+		((bch) << 14)			|			\
+		((short_mode) << 13)		|			\
+		(((page_size) & 0x7f) << 6)	|			\
+		((pages) & 0x3f)					\
+	)
+
+#define GENCMDDADDRL(adl, addr)		((adl) | ((addr) & 0xffff))
+#define GENCMDDADDRH(adh, addr)		((adh) | (((addr) >> 16) & 0xffff))
+#define GENCMDIADDRL(ail, addr)		((ail) | ((addr) & 0xffff))
+#define GENCMDIADDRH(aih, addr)		((aih) | (((addr) >> 16) & 0xffff))
+
+#define RB_STA(x)		(1 << (26 + (x)))
+#define DMA_DIR(dir)		((dir) ? NFC_CMD_N2M : NFC_CMD_M2N)
+
+#define ECC_CHECK_RETURN_FF	(-1)
+
+#define NAND_CE0		(0xe << 10)
+#define NAND_CE1		(0xd << 10)
+
+#define DMA_BUSY_TIMEOUT	0x100000
+#define CMD_FIFO_EMPTY_TIMEOUT	1000
+
+#define MAX_CE_NUM		2
+
+/* eMMC clock register, misc control */
+#define SD_EMMC_CLOCK		0x00
+#define CLK_ALWAYS_ON		BIT(28)
+#define CLK_SELECT_NAND		BIT(31)
+#define CLK_DIV_MASK		GENMASK(5, 0)
+
+#define NFC_CLK_CYCLE		6
+
+/* nand flash controller delay 3 ns */
+#define NFC_DEFAULT_DELAY	3000
+
+#define MAX_ECC_INDEX		10
+
+#define MUX_CLK_NUM_PARENTS	2
+
+#define ROW_ADDER(page, index)	(((page) >> (8 * (index))) & 0xff)
+#define MAX_CYCLE_ROW_ADDRS	3
+#define MAX_CYCLE_COLUMN_ADDRS	2
+#define DIRREAD			1
+#define DIRWRITE		0
+
+#define ECC_PARITY_BCH8_512B	14
+
+struct meson_nfc_info_format {
+	u16 info_bytes;
+
+	/* bit[5:0] are valid */
+	u8 zero_cnt;
+	struct ecc_sta {
+		u8 eccerr_cnt : 6;
+		u8 notused : 1;
+		u8 completed : 1;
+	} ecc;
+	u32 reserved;
+};
+
+#define PER_INFO_BYTE	(sizeof(struct meson_nfc_info_format))
+
+struct meson_nfc_nand_chip {
+	struct list_head node;
+	struct nand_chip nand;
+	bool is_scramble;
+	int bch_mode;
+	int nsels;
+	u8 sels[0];
+};
+
+struct meson_nand_ecc {
+	int bch;
+	int strength;
+};
+
+struct meson_nfc_data {
+	const struct nand_ecc_caps *ecc_caps;
+};
+
+struct meson_nfc_param {
+	int chip_select;
+	int rb_select;
+};
+
+struct nand_rw_cmd {
+	int cmd0;
+	int col[MAX_CYCLE_COLUMN_ADDRS];
+	int row[MAX_CYCLE_ROW_ADDRS];
+	int cmd1;
+};
+
+struct nand_timing {
+	int twb;
+	int tadl;
+	int twhr;
+};
+
+struct meson_nfc {
+	struct nand_controller controller;
+	struct clk *core_clk;
+	struct clk *device_clk;
+	struct clk *phase_tx;
+	struct clk *phase_rx;
+
+	struct device *dev;
+	void __iomem *reg_base;
+	struct regmap *reg_clk;
+	struct completion completion;
+	struct list_head chips;
+	const struct meson_nfc_data *data;
+	struct meson_nfc_param param;
+	struct nand_timing timing;
+	union {
+		int cmd[32];
+		struct nand_rw_cmd rw;
+	} cmdfifo;
+
+	dma_addr_t data_dma;
+	dma_addr_t info_dma;
+
+	unsigned long assigned_cs;
+
+	u8 *data_buf;
+	u8 *info_buf;
+};
+
+enum {
+	NFC_ECC_BCH8_1K		= 2,
+	NFC_ECC_BCH24_1K,
+	NFC_ECC_BCH30_1K,
+	NFC_ECC_BCH40_1K,
+	NFC_ECC_BCH50_1K,
+	NFC_ECC_BCH60_1K,
+};
+
+#define MESON_ECC_DATA(b, s)	{ .bch = (b),	.strength = (s)}
+
+static int meson_nand_calc_ecc_bytes(int step_size, int strength)
+{
+	int ecc_bytes;
+
+	if (step_size == 512 && strength == 8)
+		return ECC_PARITY_BCH8_512B;
+
+	ecc_bytes = DIV_ROUND_UP(strength * fls(step_size * 8), 8);
+	if (ecc_bytes % 2)
+		ecc_bytes++;
+
+	return ecc_bytes;
+}
+
+NAND_ECC_CAPS_SINGLE(meson_gxl_ecc_caps,
+		     meson_nand_calc_ecc_bytes, 1024, 8, 24, 30, 40, 50, 60);
+NAND_ECC_CAPS_SINGLE(meson_axg_ecc_caps,
+		     meson_nand_calc_ecc_bytes, 1024, 8);
+
+static inline
+struct meson_nfc_nand_chip *to_meson_nand(struct nand_chip *nand)
+{
+	return container_of(nand, struct meson_nfc_nand_chip, nand);
+}
+
+static void meson_nfc_select_chip(struct mtd_info *mtd, int chip)
+{
+	struct nand_chip *nand = mtd_to_nand(mtd);
+	struct meson_nfc_nand_chip *meson_chip = to_meson_nand(nand);
+	struct meson_nfc *nfc = nand_get_controller_data(nand);
+
+	if (chip < 0 || chip > MAX_CE_NUM)
+		return;
+
+	nfc->param.chip_select = meson_chip->sels[chip] ? NAND_CE1 : NAND_CE0;
+	nfc->param.rb_select = nfc->param.chip_select;
+}
+
+static inline void meson_nfc_cmd_idle(struct meson_nfc *nfc, u32 time)
+{
+	writel(nfc->param.chip_select | NFC_CMD_IDLE | (time & 0x3ff),
+	       nfc->reg_base + NFC_REG_CMD);
+}
+
+static inline void meson_nfc_cmd_seed(struct meson_nfc *nfc, u32 seed)
+{
+	writel(NFC_CMD_SEED | (0xc2 + (seed & 0x7fff)),
+	       nfc->reg_base + NFC_REG_CMD);
+}
+
+static void meson_nfc_cmd_access(struct meson_nfc *nfc,
+				 struct mtd_info *mtd, int raw, bool dir)
+{
+	struct nand_chip *nand = mtd_to_nand(mtd);
+	struct meson_nfc_nand_chip *meson_chip = to_meson_nand(nand);
+	u32 cmd, pagesize, pages;
+	int bch = meson_chip->bch_mode;
+	int len = mtd->writesize;
+	int scramble = meson_chip->is_scramble ? 1 : 0;
+
+	pagesize = nand->ecc.size;
+
+	if (raw) {
+		bch = NAND_ECC_NONE;
+		len = mtd->writesize + mtd->oobsize;
+		cmd = (len & 0x3fff) | (scramble << 19) | DMA_DIR(dir);
+		writel(cmd, nfc->reg_base + NFC_REG_CMD);
+		return;
+	}
+
+	pages = len / nand->ecc.size;
+
+	cmd = CMDRWGEN(DMA_DIR(dir), scramble, bch, 0, pagesize, pages);
+
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+}
+
+static inline void meson_nfc_drain_cmd(struct meson_nfc *nfc)
+{
+	/*
+	 * Insert two commands to make sure all valid commands are finished.
+	 *
+	 * The Nand flash controller is designed as two stages pipleline -
+	 *  a) fetch and b) excute.
+	 * There might be cases when the driver see command queue is empty,
+	 * but the Nand flash controller still has two commands buffered,
+	 * one is fetched into NFC request queue (ready to run), and another
+	 * is actively executing. So pushing 2 "IDLE" commands guarantees that
+	 * the pipeline is emptied.
+	 */
+	meson_nfc_cmd_idle(nfc, 0);
+	meson_nfc_cmd_idle(nfc, 0);
+}
+
+static int meson_nfc_wait_cmd_finish(struct meson_nfc *nfc,
+				     unsigned int timeout_ms)
+{
+	u32 cmd_size = 0;
+	int ret;
+
+	/* wait cmd fifo is empty */
+	ret = readl_poll_timeout(nfc->reg_base + NFC_REG_CMD, cmd_size,
+				 !((cmd_size >> 22) & 0x1f),
+				 10, timeout_ms * 1000);
+	if (ret)
+		dev_err(nfc->dev, "wait for empty cmd FIFO time out\n");
+
+	return ret;
+}
+
+static int meson_nfc_wait_dma_finish(struct meson_nfc *nfc)
+{
+	meson_nfc_drain_cmd(nfc);
+
+	return meson_nfc_wait_cmd_finish(nfc, DMA_BUSY_TIMEOUT);
+}
+
+static inline
+struct meson_nfc_info_format *nfc_info_ptr(struct meson_nfc *nfc,
+					   int index)
+{
+	return (struct meson_nfc_info_format *)&nfc->info_buf[index * 8];
+}
+
+static u8 *meson_nfc_oob_ptr(struct meson_nfc *nfc,
+			     struct mtd_info *mtd, int i)
+{
+	struct nand_chip *nand = mtd_to_nand(mtd);
+	int len;
+
+	len = nand->ecc.size * (i + 1) + (nand->ecc.bytes + 2) * i;
+
+	return nfc->data_buf + len;
+}
+
+static u8 *meson_nfc_data_ptr(struct meson_nfc *nfc,
+			      struct mtd_info *mtd, int i)
+{
+	struct nand_chip *nand = mtd_to_nand(mtd);
+	int len;
+	int temp;
+
+	temp = nand->ecc.size + nand->ecc.bytes;
+	len = (temp + 2) * i;
+
+	return nfc->data_buf + len;
+}
+
+static void meson_nfc_prase_data_oob(struct meson_nfc *nfc,
+				     struct mtd_info *mtd, u8 *buf, u8 *oobbuf)
+{
+	struct nand_chip *nand = mtd_to_nand(mtd);
+	int i, oob_len = 0;
+	u8 *dsrc, *osrc;
+
+	for (i = 0; i < mtd->writesize / nand->ecc.size; i++) {
+		if (buf) {
+			dsrc = meson_nfc_data_ptr(nfc, mtd, i);
+			memcpy(buf, dsrc, nand->ecc.size);
+			buf += nand->ecc.size;
+		}
+		oob_len = nand->ecc.bytes + 2;
+		osrc = meson_nfc_oob_ptr(nfc, mtd, i);
+		memcpy(oobbuf, osrc, oob_len);
+		oobbuf += oob_len;
+	}
+}
+
+static void meson_nfc_format_data_oob(struct meson_nfc *nfc,
+				      struct mtd_info *mtd,
+				      const u8 *buf, u8 *oobbuf)
+{
+	struct nand_chip *nand = mtd_to_nand(mtd);
+	int i, oob_len = 0;
+	u8 *dsrc, *osrc;
+
+	for (i = 0; i < mtd->writesize / nand->ecc.size; i++) {
+		if (buf) {
+			dsrc = meson_nfc_data_ptr(nfc, mtd, i);
+			memcpy(dsrc, buf, nand->ecc.size);
+			buf += nand->ecc.size;
+		}
+		oob_len = nand->ecc.bytes + 2;
+		osrc = meson_nfc_oob_ptr(nfc, mtd, i);
+		memcpy(osrc, oobbuf, oob_len);
+		oobbuf += oob_len;
+	}
+}
+
+static int meson_nfc_queue_rb(struct meson_nfc *nfc, int timeout_ms)
+{
+	u32 cmd, cfg;
+	int ret = 0;
+
+	meson_nfc_cmd_idle(nfc, nfc->timing.twb);
+	meson_nfc_drain_cmd(nfc);
+	meson_nfc_wait_cmd_finish(nfc, CMD_FIFO_EMPTY_TIMEOUT);
+
+	cfg = readl(nfc->reg_base + NFC_REG_CFG);
+	cfg |= (1 << 21);
+	writel(cfg, nfc->reg_base + NFC_REG_CFG);
+
+	init_completion(&nfc->completion);
+
+	cmd = NFC_CMD_RB | (0x1 << 14) | nfc->param.chip_select | 0x18;
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+
+	ret = wait_for_completion_timeout(&nfc->completion,
+					  msecs_to_jiffies(timeout_ms));
+	if (ret == 0) {
+		dev_err(nfc->dev, "wait nand irq timeout\n");
+		ret = -1;
+	}
+	return ret;
+}
+
+static void meson_nfc_set_user_byte(struct mtd_info *mtd,
+				    struct nand_chip *chip, u8 *oob_buf)
+{
+	struct meson_nfc *nfc = nand_get_controller_data(chip);
+	struct meson_nfc_info_format *info;
+	int i, count;
+
+	for (i = 0, count = 0; i < chip->ecc.steps; i++, count += 2) {
+		info = nfc_info_ptr(nfc, i);
+		info->info_bytes =
+			oob_buf[count] | (oob_buf[count + 1] << 8);
+	}
+}
+
+static void meson_nfc_get_user_byte(struct mtd_info *mtd,
+				    struct nand_chip *chip, u8 *oob_buf)
+{
+	struct meson_nfc *nfc = nand_get_controller_data(chip);
+	struct meson_nfc_info_format *info;
+	int i, count;
+
+	for (i = 0, count = 0; i < chip->ecc.steps; i++, count += 2) {
+		info = nfc_info_ptr(nfc, i);
+		oob_buf[count] = info->info_bytes & 0xff;
+		oob_buf[count + 1] = (info->info_bytes >> 8) & 0xff;
+	}
+}
+
+static int meson_nfc_ecc_correct(struct mtd_info *mtd,
+				 struct nand_chip *chip)
+{
+	struct meson_nfc *nfc = nand_get_controller_data(chip);
+	struct meson_nfc_nand_chip *meson_chip = to_meson_nand(chip);
+	struct meson_nfc_info_format *info;
+	u32 bitflips = 0, i;
+	u8 zero_cnt;
+
+	for (i = 0; i < chip->ecc.steps; i++) {
+		info = nfc_info_ptr(nfc, i);
+		if (info->ecc.eccerr_cnt == 0x3f) {
+			zero_cnt = info->zero_cnt & 0x3f;
+			if (meson_chip->is_scramble &&
+			    zero_cnt < chip->ecc.strength)
+				return ECC_CHECK_RETURN_FF;
+			mtd->ecc_stats.failed++;
+			continue;
+		}
+		mtd->ecc_stats.corrected += info->ecc.eccerr_cnt;
+		bitflips = max_t(u32, bitflips, info->ecc.eccerr_cnt);
+	}
+
+	return bitflips;
+}
+
+static inline u8 meson_nfc_read_byte(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct meson_nfc *nfc = nand_get_controller_data(chip);
+	u32 cmd;
+
+	cmd = nfc->param.chip_select | NFC_CMD_DRD | 0;
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+
+	meson_nfc_drain_cmd(nfc);
+
+	meson_nfc_wait_cmd_finish(nfc, 1000);
+
+	return readb(nfc->reg_base + NFC_REG_BUF);
+}
+
+static void meson_nfc_read_buf(struct mtd_info *mtd, u8 *buf, int len)
+{
+	int i;
+
+	for (i = 0; i < len; i++)
+		buf[i] = meson_nfc_read_byte(mtd);
+}
+
+static void meson_nfc_write_byte(struct mtd_info *mtd, u8 byte)
+{
+	struct meson_nfc *nfc = nand_get_controller_data(mtd_to_nand(mtd));
+	u32 cmd;
+
+	meson_nfc_cmd_idle(nfc, nfc->timing.twb);
+
+	cmd = nfc->param.chip_select | NFC_CMD_DWR | (byte & 0xff);
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+
+	meson_nfc_cmd_idle(nfc, nfc->timing.twb);
+	meson_nfc_cmd_idle(nfc, 0);
+
+	meson_nfc_wait_cmd_finish(nfc, CMD_FIFO_EMPTY_TIMEOUT);
+}
+
+static void meson_nfc_write_buf(struct mtd_info *mtd,
+				const u8 *buf, int len)
+{
+	int i;
+
+	for (i = 0; i < len; i++)
+		meson_nfc_write_byte(mtd, buf[i]);
+}
+
+static int
+meson_nfc_rw_cmd_prepare_and_execute(struct meson_nfc *nfc,
+				     struct nand_chip *chip, int page, bool in)
+{
+	const struct nand_sdr_timings *sdr =
+		nand_get_sdr_timings(&chip->data_interface);
+	int cs = nfc->param.chip_select;
+	int i, cmd0, cmd_num;
+	int ret = 0;
+
+	cmd0 = in ? NAND_CMD_READ0 : NAND_CMD_SEQIN;
+	cmd_num = sizeof(struct nand_rw_cmd) / sizeof(int);
+	if (!in)
+		cmd_num--;
+
+	nfc->cmdfifo.rw.cmd0 = cs | NFC_CMD_CLE | cmd0;
+	for (i = 0; i < MAX_CYCLE_COLUMN_ADDRS; i++)
+		nfc->cmdfifo.rw.col[i] = cs | NFC_CMD_ALE | 0;
+
+	for (i = 0; i < MAX_CYCLE_ROW_ADDRS; i++)
+		nfc->cmdfifo.rw.row[i] = cs | NFC_CMD_ALE | ROW_ADDER(page, i);
+
+	nfc->cmdfifo.rw.cmd1 = cs | NFC_CMD_CLE | NAND_CMD_READSTART;
+
+	for (i = 0; i < cmd_num; i++)
+		writel(nfc->cmdfifo.cmd[i], nfc->reg_base + NFC_REG_CMD);
+
+	if (in)
+		meson_nfc_queue_rb(nfc, sdr->tR_max);
+	else
+		meson_nfc_cmd_idle(nfc, nfc->timing.tadl);
+
+	return ret;
+}
+
+static int meson_nfc_write_page_sub(struct mtd_info *mtd,
+				    struct nand_chip *chip, const u8 *buf,
+				    int page, int raw)
+{
+	const struct nand_sdr_timings *sdr =
+		nand_get_sdr_timings(&chip->data_interface);
+	struct meson_nfc *nfc = nand_get_controller_data(chip);
+	dma_addr_t daddr, iaddr;
+	u32 cmd, ecc_step;
+	int ret;
+
+	ecc_step = mtd->writesize / chip->ecc.size;
+
+	daddr = dma_map_single(nfc->dev, (void *)nfc->data_buf,
+			       mtd->writesize + mtd->oobsize,
+			       DMA_TO_DEVICE);
+	ret = dma_mapping_error(nfc->dev, daddr);
+	if (ret) {
+		dev_err(nfc->dev, "dma mapping error\n");
+		goto err;
+	}
+
+	iaddr = dma_map_single(nfc->dev, (void *)nfc->info_buf,
+			       ecc_step * PER_INFO_BYTE,
+			       DMA_TO_DEVICE);
+	ret = dma_mapping_error(nfc->dev, iaddr);
+	if (ret) {
+		dev_err(nfc->dev, "dma mapping error\n");
+		goto err_map_daddr;
+	}
+
+	ret = meson_nfc_rw_cmd_prepare_and_execute(nfc, chip, page, DIRWRITE);
+	if (ret)
+		goto err_map_iaddr;
+
+	cmd = GENCMDDADDRL(NFC_CMD_ADL, daddr);
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+
+	cmd = GENCMDDADDRH(NFC_CMD_ADH, daddr);
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+
+	cmd = GENCMDIADDRL(NFC_CMD_AIL, iaddr);
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+
+	cmd = GENCMDIADDRH(NFC_CMD_AIH, iaddr);
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+
+	meson_nfc_cmd_seed(nfc, page);
+
+	meson_nfc_cmd_access(nfc, mtd, raw, DIRWRITE);
+
+	ret = meson_nfc_wait_dma_finish(nfc);
+	cmd = nfc->param.chip_select | NFC_CMD_CLE | NAND_CMD_PAGEPROG;
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+	meson_nfc_queue_rb(nfc, sdr->tPROG_max);
+
+err_map_iaddr:
+	dma_unmap_single(nfc->dev, iaddr,
+			 ecc_step * PER_INFO_BYTE, DMA_TO_DEVICE);
+err_map_daddr:
+	dma_unmap_single(nfc->dev, daddr,
+			 mtd->writesize + mtd->oobsize, DMA_TO_DEVICE);
+err:
+	return ret;
+}
+
+static int meson_nfc_write_page_raw(struct mtd_info *mtd,
+				    struct nand_chip *chip, const u8 *buf,
+				    int oob_required, int page)
+{
+	struct meson_nfc *nfc = nand_get_controller_data(chip);
+	u8 *oob_buf = chip->oob_poi;
+
+	meson_nfc_format_data_oob(nfc, mtd, buf, oob_buf);
+
+	return meson_nfc_write_page_sub(mtd, chip, nfc->data_buf, page, 1);
+}
+
+static int meson_nfc_write_page_hwecc(struct mtd_info *mtd,
+				      struct nand_chip *chip, const u8 *buf,
+				      int oob_required, int page)
+{
+	struct meson_nfc *nfc = nand_get_controller_data(chip);
+	u8 *oob_buf = chip->oob_poi;
+
+	memcpy(nfc->data_buf, buf, mtd->writesize);
+	meson_nfc_set_user_byte(mtd, chip, oob_buf);
+
+	return meson_nfc_write_page_sub(mtd, chip, nfc->data_buf, page, 0);
+}
+
+static void meson_nfc_check_ecc_pages_valid(struct meson_nfc *nfc,
+					    struct mtd_info *mtd, int raw)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct meson_nfc_info_format *info;
+	int neccpages, i;
+
+	neccpages = raw ? 1 : (mtd->writesize / chip->ecc.size);
+
+	for (i = 0; i < neccpages; i++) {
+		info = nfc_info_ptr(nfc, neccpages - 1);
+		if (info->ecc.completed == 0)
+			dev_err(nfc->dev, "seems eccpage is invalid\n");
+	}
+}
+
+static int meson_nfc_read_page_sub(struct mtd_info *mtd,
+				   struct nand_chip *chip, const u8 *buf,
+				   int page, int raw)
+{
+	struct meson_nfc *nfc = nand_get_controller_data(chip);
+	dma_addr_t daddr, iaddr;
+	u32 cmd, ecc_step;
+	int ret;
+
+	ecc_step =  mtd->writesize / chip->ecc.size;
+
+	daddr = dma_map_single(nfc->dev, (void *)nfc->data_buf,
+			       mtd->writesize + mtd->oobsize, DMA_FROM_DEVICE);
+	ret = dma_mapping_error(nfc->dev, daddr);
+	if (ret) {
+		dev_err(nfc->dev, "dma mapping error\n");
+		goto err;
+	}
+
+	iaddr = dma_map_single(nfc->dev, (void *)nfc->info_buf,
+			       ecc_step * PER_INFO_BYTE, DMA_FROM_DEVICE);
+	ret = dma_mapping_error(nfc->dev, iaddr);
+	if (ret) {
+		dev_err(nfc->dev, "dma mapping error\n");
+		goto err_map_daddr;
+	}
+
+	ret = meson_nfc_rw_cmd_prepare_and_execute(nfc, chip, page, DIRREAD);
+	if (ret)
+		goto err_map_iaddr;
+
+	cmd = GENCMDDADDRL(NFC_CMD_ADL, daddr);
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+
+	cmd = GENCMDDADDRH(NFC_CMD_ADH, daddr);
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+
+	cmd = GENCMDIADDRL(NFC_CMD_AIL, iaddr);
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+
+	cmd = GENCMDIADDRH(NFC_CMD_AIH, iaddr);
+	writel(cmd, nfc->reg_base + NFC_REG_CMD);
+
+	meson_nfc_cmd_seed(nfc, page);
+	meson_nfc_cmd_access(nfc, mtd, raw, DIRREAD);
+	ret = meson_nfc_wait_dma_finish(nfc);
+	meson_nfc_check_ecc_pages_valid(nfc, mtd, raw);
+
+err_map_iaddr:
+	dma_unmap_single(nfc->dev, iaddr,
+			 ecc_step * PER_INFO_BYTE, DMA_FROM_DEVICE);
+err_map_daddr:
+	dma_unmap_single(nfc->dev, daddr,
+			 mtd->writesize + mtd->oobsize, DMA_FROM_DEVICE);
+err:
+	return ret;
+}
+
+static int meson_nfc_read_page_raw(struct mtd_info *mtd,
+				   struct nand_chip *chip, u8 *buf,
+				   int oob_required, int page)
+{
+	struct meson_nfc *nfc = nand_get_controller_data(chip);
+	u8 *oob_buf = chip->oob_poi;
+	int ret;
+
+	ret = meson_nfc_read_page_sub(mtd, chip, nfc->data_buf, page, 1);
+	if (ret)
+		return ret;
+
+	meson_nfc_prase_data_oob(nfc, mtd, buf, oob_buf);
+
+	return 0;
+}
+
+static int meson_nfc_read_page_hwecc(struct mtd_info *mtd,
+				     struct nand_chip *chip, u8 *buf,
+				     int oob_required, int page)
+{
+	struct meson_nfc *nfc = nand_get_controller_data(chip);
+	u8 *oob_buf = chip->oob_poi;
+	int ret;
+
+	ret = meson_nfc_read_page_sub(mtd, chip, nfc->data_buf, page, 0);
+	if (ret)
+		return ret;
+
+	meson_nfc_get_user_byte(mtd, chip, oob_buf);
+
+	ret = meson_nfc_ecc_correct(mtd, chip);
+	if (ret == ECC_CHECK_RETURN_FF) {
+		if (buf)
+			memset(buf, 0xff, mtd->writesize);
+
+		memset(oob_buf, 0xff, mtd->oobsize);
+		return 0;
+	}
+
+	if (buf && buf != nfc->data_buf)
+		memcpy(buf, nfc->data_buf, mtd->writesize);
+
+	return ret;
+}
+
+static int meson_nfc_read_oob_raw(struct mtd_info *mtd,
+				  struct nand_chip *chip, int page)
+{
+	return meson_nfc_read_page_raw(mtd, chip, NULL, 1, page);
+}
+
+static int meson_nfc_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+			      int page)
+{
+	return meson_nfc_read_page_hwecc(mtd, chip, NULL, 1, page);
+}
+
+static int meson_nfc_exec_op(struct nand_chip *chip,
+			     const struct nand_operation *op, bool check_only)
+{
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	struct meson_nfc *nfc = nand_get_controller_data(chip);
+	const struct nand_op_instr *instr = NULL;
+	int ret = 0, cmd;
+	unsigned int op_id;
+	int i;
+
+	for (op_id = 0; op_id < op->ninstrs; op_id++) {
+		instr = &op->instrs[op_id];
+		switch (instr->type) {
+		case NAND_OP_CMD_INSTR:
+			if (instr->ctx.cmd.opcode == NAND_CMD_STATUS)
+				meson_nfc_cmd_idle(nfc, nfc->timing.twb);
+			cmd = nfc->param.chip_select | NFC_CMD_CLE;
+			cmd |= instr->ctx.cmd.opcode & 0xff;
+			writel(cmd, nfc->reg_base + NFC_REG_CMD);
+			if (instr->ctx.cmd.opcode == NAND_CMD_STATUS)
+				meson_nfc_cmd_idle(nfc, nfc->timing.twhr);
+			break;
+
+		case NAND_OP_ADDR_INSTR:
+			for (i = 0; i < instr->ctx.addr.naddrs; i++) {
+				cmd = nfc->param.chip_select | NFC_CMD_ALE;
+				cmd |= instr->ctx.addr.addrs[i] & 0xff;
+				writel(cmd, nfc->reg_base + NFC_REG_CMD);
+			}
+			break;
+
+		case NAND_OP_DATA_IN_INSTR:
+			meson_nfc_read_buf(mtd, instr->ctx.data.buf.in,
+					   instr->ctx.data.len);
+			break;
+
+		case NAND_OP_DATA_OUT_INSTR:
+			meson_nfc_write_buf(mtd, instr->ctx.data.buf.out,
+					    instr->ctx.data.len);
+			break;
+
+		case NAND_OP_WAITRDY_INSTR:
+			meson_nfc_queue_rb(nfc, instr->ctx.waitrdy.timeout_ms);
+			break;
+		}
+	}
+	return ret;
+}
+
+static int meson_ooblayout_ecc(struct mtd_info *mtd, int section,
+			       struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+
+	if (section >= chip->ecc.steps)
+		return -ERANGE;
+
+	oobregion->offset =  2 + (section * (2 + chip->ecc.bytes));
+	oobregion->length = chip->ecc.bytes;
+
+	return 0;
+}
+
+static int meson_ooblayout_free(struct mtd_info *mtd, int section,
+				struct mtd_oob_region *oobregion)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+
+	if (section >= chip->ecc.steps)
+		return -ERANGE;
+
+	oobregion->offset = section * (2 + chip->ecc.bytes);
+	oobregion->length = 2;
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops meson_ooblayout_ops = {
+	.ecc = meson_ooblayout_ecc,
+	.free = meson_ooblayout_free,
+};
+
+static int meson_nfc_clk_init(struct meson_nfc *nfc)
+{
+	int ret;
+
+	/* request core clock */
+	nfc->core_clk = devm_clk_get(nfc->dev, "core");
+	if (IS_ERR(nfc->core_clk)) {
+		dev_err(nfc->dev, "failed to get core clk\n");
+		return PTR_ERR(nfc->core_clk);
+	}
+
+	nfc->device_clk = devm_clk_get(nfc->dev, "device");
+	if (IS_ERR(nfc->device_clk)) {
+		dev_err(nfc->dev, "failed to get device clk\n");
+		return PTR_ERR(nfc->device_clk);
+	}
+
+	nfc->phase_tx = devm_clk_get(nfc->dev, "tx");
+	if (IS_ERR(nfc->phase_tx)) {
+		dev_err(nfc->dev, "failed to get tx clk\n");
+		return PTR_ERR(nfc->phase_tx);
+	}
+
+	nfc->phase_rx = devm_clk_get(nfc->dev, "rx");
+	if (IS_ERR(nfc->phase_rx)) {
+		dev_err(nfc->dev, "failed to get rx clk\n");
+		return PTR_ERR(nfc->phase_rx);
+	}
+
+	/* init SD_EMMC_CLOCK to sane defaults w/min clock rate */
+	regmap_update_bits(nfc->reg_clk, 0,
+			   CLK_SELECT_NAND | CLK_ALWAYS_ON | CLK_DIV_MASK,
+			   CLK_SELECT_NAND | CLK_ALWAYS_ON | CLK_DIV_MASK);
+
+	ret = clk_prepare_enable(nfc->core_clk);
+	if (ret) {
+		dev_err(nfc->dev, "failed to enable core clk\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(nfc->device_clk);
+	if (ret) {
+		dev_err(nfc->dev, "failed to enable device clk\n");
+		clk_disable_unprepare(nfc->core_clk);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(nfc->phase_tx);
+	if (ret) {
+		dev_err(nfc->dev, "failed to enable tx clk\n");
+		clk_disable_unprepare(nfc->core_clk);
+		clk_disable_unprepare(nfc->device_clk);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(nfc->phase_rx);
+	if (ret) {
+		dev_err(nfc->dev, "failed to enable rx clk\n");
+		clk_disable_unprepare(nfc->core_clk);
+		clk_disable_unprepare(nfc->device_clk);
+		clk_disable_unprepare(nfc->phase_tx);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void meson_nfc_disable_clk(struct meson_nfc *nfc)
+{
+	clk_disable_unprepare(nfc->phase_rx);
+	clk_disable_unprepare(nfc->phase_tx);
+	clk_disable_unprepare(nfc->device_clk);
+	clk_disable_unprepare(nfc->core_clk);
+}
+
+static void meson_nfc_free_buffer(struct meson_nfc *nfc)
+{
+	kfree(nfc->info_buf);
+	kfree(nfc->data_buf);
+}
+
+static int meson_nfc_buffer_init(struct mtd_info *mtd)
+{
+	struct nand_chip *nand = mtd_to_nand(mtd);
+	struct meson_nfc *nfc = nand_get_controller_data(nand);
+	static int max_page_bytes, max_info_bytes;
+	int page_bytes, info_bytes;
+	int nsectors;
+
+	nsectors = mtd->writesize / nand->ecc.size;
+	page_bytes =  mtd->writesize + mtd->oobsize;
+	info_bytes = nsectors * PER_INFO_BYTE;
+
+	if (nfc->data_buf && nfc->info_buf) {
+		if (max_page_bytes < page_bytes)
+			meson_nfc_free_buffer(nfc);
+		else
+			return 0;
+	}
+
+	max_page_bytes = max_t(int, max_page_bytes, page_bytes);
+	max_info_bytes = max_t(int, max_info_bytes, info_bytes);
+
+	nfc->data_buf = kmalloc(max_page_bytes, GFP_KERNEL);
+	if (!nfc->data_buf)
+		return -ENOMEM;
+
+	nfc->info_buf = kmalloc(max_info_bytes, GFP_KERNEL);
+	if (!nfc->info_buf) {
+		kfree(nfc->data_buf);
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
+static int meson_nfc_calc_set_timing(struct meson_nfc *nfc,
+				     const struct nand_sdr_timings *timings)
+{
+	struct nand_timing *timing = &nfc->timing;
+	int div, bt_min, bt_max, bus_timing;
+	int ret;
+
+	div = DIV_ROUND_UP((timings->tRC_min / 1000), NFC_CLK_CYCLE);
+	ret = clk_set_rate(nfc->device_clk, 1000000000 / div);
+	if (ret) {
+		dev_err(nfc->dev, "failed to set nand clock rate\n");
+		return ret;
+	}
+
+	timing->twb = DIV_ROUND_UP(PSEC_TO_NSEC(timings->tWB_max),
+				   div * NFC_CLK_CYCLE);
+	timing->tadl = DIV_ROUND_UP(PSEC_TO_NSEC(timings->tADL_min),
+				    div * NFC_CLK_CYCLE);
+	timing->twhr = DIV_ROUND_UP(PSEC_TO_NSEC(timings->tWHR_min),
+				    div * NFC_CLK_CYCLE);
+
+	bt_min = (timings->tREA_max + NFC_DEFAULT_DELAY) / div;
+	bt_max = (NFC_DEFAULT_DELAY + timings->tRHOH_min
+			+ timings->tRC_min / 2) / div;
+
+	bt_min = DIV_ROUND_UP(bt_min, 1000);
+	bt_max = DIV_ROUND_UP(bt_max, 1000);
+
+	if (bt_max < bt_min)
+		return -EINVAL;
+
+	bus_timing = (bt_min + bt_max) / 2 + 1;
+
+	writel((1 << 21), nfc->reg_base + NFC_REG_CFG);
+	writel((NFC_CLK_CYCLE - 1) | (bus_timing << 5),
+	       nfc->reg_base + NFC_REG_CFG);
+
+	writel((1 << 31), nfc->reg_base + NFC_REG_CMD);
+
+	return 0;
+}
+
+static int
+meson_nfc_setup_data_interface(struct mtd_info *mtd, int csline,
+			       const struct nand_data_interface *conf)
+{
+	struct nand_chip *nand = mtd_to_nand(mtd);
+	struct meson_nfc *nfc = nand_get_controller_data(nand);
+	const struct nand_sdr_timings *timings;
+
+	timings = nand_get_sdr_timings(conf);
+	if (IS_ERR(timings))
+		return -ENOTSUPP;
+
+	if (csline == NAND_DATA_IFACE_CHECK_ONLY)
+		return 0;
+
+	meson_nfc_calc_set_timing(nfc, timings);
+	return 0;
+}
+
+static int meson_nand_bch_mode(struct nand_chip *nand)
+{
+	struct meson_nfc_nand_chip *meson_chip = to_meson_nand(nand);
+	struct meson_nand_ecc meson_ecc[] = {
+		MESON_ECC_DATA(NFC_ECC_BCH8_1K, 8),
+		MESON_ECC_DATA(NFC_ECC_BCH24_1K, 24),
+		MESON_ECC_DATA(NFC_ECC_BCH30_1K, 30),
+		MESON_ECC_DATA(NFC_ECC_BCH40_1K, 40),
+		MESON_ECC_DATA(NFC_ECC_BCH50_1K, 50),
+		MESON_ECC_DATA(NFC_ECC_BCH60_1K, 60),
+	};
+	int i, ret = 0;
+
+	if (nand->ecc.strength > 60 || nand->ecc.strength < 8)
+		return -EINVAL;
+
+	for (i = 0; i < sizeof(meson_ecc); i++) {
+		if (meson_ecc[i].strength == nand->ecc.strength) {
+			meson_chip->bch_mode = meson_ecc[i].bch;
+			break;
+		}
+	}
+
+	return ret;
+}
+
+static int meson_nand_attach_chip(struct nand_chip *nand)
+{
+	struct meson_nfc *nfc = nand_get_controller_data(nand);
+	struct meson_nfc_nand_chip *meson_chip = to_meson_nand(nand);
+	struct mtd_info *mtd = nand_to_mtd(nand);
+	int nsectors = mtd->writesize / 1024;
+	int ret;
+
+	if (!mtd->name) {
+		mtd->name = devm_kasprintf(nfc->dev, GFP_KERNEL,
+					   "%s:nand%d",
+					   dev_name(nfc->dev),
+					   meson_chip->sels[0]);
+		if (!mtd->name)
+			return -ENOMEM;
+	}
+
+	if (nand->bbt_options & NAND_BBT_USE_FLASH)
+		nand->bbt_options |= NAND_BBT_NO_OOB;
+
+	nand->options |= NAND_NO_SUBPAGE_WRITE;
+
+	meson_chip->is_scramble =
+		(nand->options & NAND_NEED_SCRAMBLING) ? 1 : 0;
+
+	ret = nand_ecc_choose_conf(nand, nfc->data->ecc_caps,
+				   mtd->oobsize - 2 * nsectors);
+	if (ret) {
+		dev_err(nfc->dev, "failed to ecc init\n");
+		return -EINVAL;
+	}
+
+	ret = meson_nand_bch_mode(nand);
+	if (ret)
+		return -EINVAL;
+
+	nand->ecc.mode = NAND_ECC_HW;
+	nand->ecc.write_page_raw = meson_nfc_write_page_raw;
+	nand->ecc.write_page = meson_nfc_write_page_hwecc;
+	nand->ecc.write_oob_raw = nand_write_oob_std;
+	nand->ecc.write_oob = nand_write_oob_std;
+
+	nand->ecc.read_page_raw = meson_nfc_read_page_raw;
+	nand->ecc.read_page = meson_nfc_read_page_hwecc;
+	nand->ecc.read_oob_raw = meson_nfc_read_oob_raw;
+	nand->ecc.read_oob = meson_nfc_read_oob;
+
+	if (nand->options & NAND_BUSWIDTH_16) {
+		dev_err(nfc->dev, "16bits buswidth not supported");
+		return -EINVAL;
+	}
+
+	ret = meson_nfc_buffer_init(mtd);
+	if (ret)
+		return -ENOMEM;
+
+	return ret;
+}
+
+static const struct nand_controller_ops meson_nand_controller_ops = {
+	.attach_chip = meson_nand_attach_chip,
+};
+
+static int
+meson_nfc_nand_chip_init(struct device *dev,
+			 struct meson_nfc *nfc, struct device_node *np)
+{
+	struct meson_nfc_nand_chip *chip;
+	struct nand_chip *nand;
+	struct mtd_info *mtd;
+	int ret, nsels, i;
+	u32 tmp;
+
+	if (!of_get_property(np, "reg", &nsels))
+		return -EINVAL;
+
+	nsels /= sizeof(u32);
+	if (!nsels || nsels > MAX_CE_NUM) {
+		dev_err(dev, "invalid reg property size\n");
+		return -EINVAL;
+	}
+
+	chip = devm_kzalloc(dev, sizeof(*chip) + (nsels * sizeof(u8)),
+			    GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->nsels = nsels;
+
+	for (i = 0; i < nsels; i++) {
+		ret = of_property_read_u32_index(np, "reg", i, &tmp);
+		if (ret) {
+			dev_err(dev, "could not retrieve reg property: %d\n",
+				ret);
+			return ret;
+		}
+
+		if (test_and_set_bit(tmp, &nfc->assigned_cs)) {
+			dev_err(dev, "CS %d already assigned\n", tmp);
+			return -EINVAL;
+		}
+	}
+
+	nand = &chip->nand;
+	nand->controller = &nfc->controller;
+	nand->controller->ops = &meson_nand_controller_ops;
+	nand_set_flash_node(nand, np);
+	nand_set_controller_data(nand, nfc);
+
+	nand->options |= NAND_USE_BOUNCE_BUFFER;
+	nand->select_chip = meson_nfc_select_chip;
+	nand->exec_op = meson_nfc_exec_op;
+	nand->setup_data_interface = meson_nfc_setup_data_interface;
+	mtd = nand_to_mtd(nand);
+	mtd->owner = THIS_MODULE;
+	mtd->dev.parent = dev;
+
+	ret = nand_scan(mtd, nsels);
+	if (ret)
+		return ret;
+
+	ret = mtd_device_register(mtd, NULL, 0);
+	if (ret) {
+		dev_err(dev, "failed to register mtd device: %d\n", ret);
+		nand_cleanup(nand);
+		return ret;
+	}
+
+	list_add_tail(&chip->node, &nfc->chips);
+
+	return 0;
+}
+
+static int meson_nfc_nand_chip_cleanup(struct meson_nfc *nfc)
+{
+	struct meson_nfc_nand_chip *chip;
+	struct mtd_info *mtd;
+	int ret;
+
+	while (!list_empty(&nfc->chips)) {
+		chip = list_first_entry(&nfc->chips, struct meson_nfc_nand_chip,
+					node);
+		mtd = nand_to_mtd(&chip->nand);
+		ret = mtd_device_unregister(mtd);
+		if (ret)
+			return ret;
+
+		nand_cleanup(&chip->nand);
+		list_del(&chip->node);
+	}
+
+	return 0;
+}
+
+static int meson_nfc_nand_chips_init(struct device *dev,
+				     struct meson_nfc *nfc)
+{
+	struct device_node *np = dev->of_node;
+	struct device_node *nand_np;
+	int ret;
+
+	for_each_child_of_node(np, nand_np) {
+		ret = meson_nfc_nand_chip_init(dev, nfc, nand_np);
+		if (ret) {
+			meson_nfc_nand_chip_cleanup(nfc);
+			return ret;
+		}
+	}
+	meson_nfc_free_buffer(nfc);
+
+	return 0;
+}
+
+static irqreturn_t meson_nfc_irq(int irq, void *id)
+{
+	struct meson_nfc *nfc = id;
+	u32 cfg;
+
+	cfg = readl(nfc->reg_base + NFC_REG_CFG);
+	if (!(cfg & NFC_RB_IRQ_EN))
+		return IRQ_NONE;
+
+	cfg &= ~(NFC_RB_IRQ_EN);
+	writel(cfg, nfc->reg_base + NFC_REG_CFG);
+
+	complete(&nfc->completion);
+	return IRQ_HANDLED;
+}
+
+static const struct meson_nfc_data meson_gxl_data = {
+	.ecc_caps = &meson_gxl_ecc_caps,
+};
+
+static const struct meson_nfc_data meson_axg_data = {
+	.ecc_caps = &meson_axg_ecc_caps,
+};
+
+static const struct of_device_id meson_nfc_id_table[] = {
+	{
+		.compatible = "amlogic,meson-gxl-nfc",
+		.data = &meson_gxl_data,
+	}, {
+		.compatible = "amlogic,meson-axg-nfc",
+		.data = &meson_axg_data,
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(of, meson_nfc_id_table);
+
+static int meson_nfc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct meson_nfc *nfc;
+	struct resource *res;
+	int ret, irq;
+
+	nfc = devm_kzalloc(dev, sizeof(*nfc), GFP_KERNEL);
+	if (!nfc)
+		return -ENOMEM;
+
+	nfc->data = of_device_get_match_data(&pdev->dev);
+	if (!nfc->data)
+		return -ENODEV;
+
+	nand_controller_init(&nfc->controller);
+	INIT_LIST_HEAD(&nfc->chips);
+
+	nfc->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	nfc->reg_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(nfc->reg_base))
+		return PTR_ERR(nfc->reg_base);
+
+	nfc->reg_clk =
+		syscon_regmap_lookup_by_phandle(dev->of_node,
+						"amlogic,mmc-syscon");
+	if (IS_ERR(nfc->reg_clk)) {
+		dev_err(dev, "Failed to lookup clock base\n");
+		return PTR_ERR(nfc->reg_clk);
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "no nfi irq resource\n");
+		return -EINVAL;
+	}
+
+	ret = meson_nfc_clk_init(nfc);
+	if (ret) {
+		dev_err(dev, "failed to initialize nand clk\n");
+		goto err;
+	}
+
+	writel(0, nfc->reg_base + NFC_REG_CFG);
+	ret = devm_request_irq(dev, irq, meson_nfc_irq, 0, dev_name(dev), nfc);
+	if (ret) {
+		dev_err(dev, "failed to request nfi irq\n");
+		ret = -EINVAL;
+		goto err_clk;
+	}
+
+	ret = dma_set_mask(dev, DMA_BIT_MASK(32));
+	if (ret) {
+		dev_err(dev, "failed to set dma mask\n");
+		goto err_clk;
+	}
+
+	platform_set_drvdata(pdev, nfc);
+
+	ret = meson_nfc_nand_chips_init(dev, nfc);
+	if (ret) {
+		dev_err(dev, "failed to init nand chips\n");
+		goto err_clk;
+	}
+
+	return 0;
+
+err_clk:
+	meson_nfc_disable_clk(nfc);
+err:
+	return ret;
+}
+
+static int meson_nfc_remove(struct platform_device *pdev)
+{
+	struct meson_nfc *nfc = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = meson_nfc_nand_chip_cleanup(nfc);
+	if (ret)
+		return ret;
+
+	meson_nfc_disable_clk(nfc);
+
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+static struct platform_driver meson_nfc_driver = {
+	.probe  = meson_nfc_probe,
+	.remove = meson_nfc_remove,
+	.driver = {
+		.name  = "meson-nand",
+		.of_match_table = meson_nfc_id_table,
+	},
+};
+module_platform_driver(meson_nfc_driver);
+
+MODULE_LICENSE("Dual MIT/GPL");
+MODULE_AUTHOR("Liang Yang <liang.yang@amlogic.com>");
+MODULE_DESCRIPTION("Amlogic's Meson NAND Flash Controller driver");