@@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-a95x.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
new file mode 100644
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ * Copyright (c) 2018 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905d.dtsi"
+
+/ {
+ compatible = "smartlabs,sml5442tw", "amlogic,s905d", "amlogic,meson-gxl";
+ model = "Smartlabs SML-5442TW";
+
+ aliases {
+ serial0 = &uart_AO;
+ serial1 = &uart_A;
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ yellow {
+ label = "sml5442tw:yellow";
+ gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ blue {
+ label = "sml5442tw:blue";
+ gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ green {
+ label = "sml5442tw:green";
+ gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ red {
+ label = "sml5442tw:red";
+ gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ hdmi_5v: regulator-hdmi-5v {
+ compatible = "regulator-fixed";
+
+ regulator-name = "HDMI_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+};
+
+&cec_AO {
+ status = "okay";
+ pinctrl-0 = <&ao_cec_pins>;
+ pinctrl-names = "default";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
+
+ðmac {
+ status = "okay";
+ phy-mode = "rmii";
+ phy-handle = <&internal_phy>;
+};
+
+/* This will enable the bluetooth module */
+&gpio {
+ bt-en {
+ gpio-hog;
+ gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "bt-en";
+ };
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&hdmi_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&i2c_A {
+ status = "okay";
+ pinctrl-0 = <&i2c_a_pins>;
+ pinctrl-names = "default";
+};
+
+&internal_phy {
+ pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>;
+ pinctrl-names = "default";
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+ linux,rc-map-name = "rc-o2cz-khamsin";
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <100000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* This is connected to the Bluetooth module: */
+&uart_A {
+ status = "okay";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+};
+
+/* This UART is brought out to the debug header */
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb0 {
+ status = "okay";
+};
The Smartlabs SML-5442TW is broadly similar to the P231 reference design but with the following differences: - Yellow and Blue front-panel LEDs are available but disabled - Red/Green LED is used to signal off/on status - GPIOX_17 is set high to enable the QCA9377 wireless module - uart_AO can be accessed after opening the case; soldered pins exist Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> --- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++ 2 files changed, 293 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts