| Message ID | 20181112141239.19646-4-linus.walleij@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Convert MMC slot GPIO to descriptors | expand |
Hi Linus, On Mon, Nov 12, 2018 at 03:12:32PM +0100, Linus Walleij wrote: > The power GPIO line is passed with inversion flags and all from > the platform data. Switch to using an optional GPIO descriptor and > use this to switch the power. > > Augment the only boardfile to pass in the proper "power" descriptor > in the GPIO descriptor machine table instead. > > As the GPIO handling is now much simpler, we can cut down on some > overhead code. > > Cc: Paul Cercueil <paul@crapouillou.net> > Cc: linux-mips@linux-mips.org > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Paul Burton <paul.burton@mips.com> Thanks, Paul > --- > .../mips/include/asm/mach-jz4740/jz4740_mmc.h | 2 - > arch/mips/jz4740/board-qi_lb60.c | 6 +- > drivers/mmc/host/jz4740_mmc.c | 65 +++++-------------- > 3 files changed, 18 insertions(+), 55 deletions(-)
On 12 November 2018 at 15:12, Linus Walleij <linus.walleij@linaro.org> wrote: > The power GPIO line is passed with inversion flags and all from > the platform data. Switch to using an optional GPIO descriptor and > use this to switch the power. > > Augment the only boardfile to pass in the proper "power" descriptor > in the GPIO descriptor machine table instead. > > As the GPIO handling is now much simpler, we can cut down on some > overhead code. > > Cc: Paul Cercueil <paul@crapouillou.net> > Cc: linux-mips@linux-mips.org > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Applied for next, thanks! Kind regards Uffe > --- > .../mips/include/asm/mach-jz4740/jz4740_mmc.h | 2 - > arch/mips/jz4740/board-qi_lb60.c | 6 +- > drivers/mmc/host/jz4740_mmc.c | 65 +++++-------------- > 3 files changed, 18 insertions(+), 55 deletions(-) > > diff --git a/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h b/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h > index ff50aeb1a933..9a7de47c7c79 100644 > --- a/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h > +++ b/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h > @@ -3,10 +3,8 @@ > #define __LINUX_MMC_JZ4740_MMC > > struct jz4740_mmc_platform_data { > - int gpio_power; > unsigned card_detect_active_low:1; > unsigned read_only_active_low:1; > - unsigned power_active_low:1; > > unsigned data_1bit:1; > }; > diff --git a/arch/mips/jz4740/board-qi_lb60.c b/arch/mips/jz4740/board-qi_lb60.c > index 705593d40d12..6718efb400f4 100644 > --- a/arch/mips/jz4740/board-qi_lb60.c > +++ b/arch/mips/jz4740/board-qi_lb60.c > @@ -43,8 +43,6 @@ > #include "clock.h" > > /* GPIOs */ > -#define QI_LB60_GPIO_SD_VCC_EN_N JZ_GPIO_PORTD(2) > - > #define QI_LB60_GPIO_KEYOUT(x) (JZ_GPIO_PORTC(10) + (x)) > #define QI_LB60_GPIO_KEYIN(x) (JZ_GPIO_PORTD(18) + (x)) > #define QI_LB60_GPIO_KEYIN8 JZ_GPIO_PORTD(26) > @@ -385,14 +383,14 @@ static struct platform_device qi_lb60_gpio_keys = { > }; > > static struct jz4740_mmc_platform_data qi_lb60_mmc_pdata = { > - .gpio_power = QI_LB60_GPIO_SD_VCC_EN_N, > - .power_active_low = 1, > + /* Intentionally left blank */ > }; > > static struct gpiod_lookup_table qi_lb60_mmc_gpio_table = { > .dev_id = "jz4740-mmc.0", > .table = { > GPIO_LOOKUP("GPIOD", 0, "cd", GPIO_ACTIVE_HIGH), > + GPIO_LOOKUP("GPIOD", 2, "power", GPIO_ACTIVE_LOW), > { }, > }, > }; > diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c > index 44ea452add8e..6f7a99e54af0 100644 > --- a/drivers/mmc/host/jz4740_mmc.c > +++ b/drivers/mmc/host/jz4740_mmc.c > @@ -21,7 +21,7 @@ > #include <linux/dmaengine.h> > #include <linux/dma-mapping.h> > #include <linux/err.h> > -#include <linux/gpio.h> > +#include <linux/gpio/consumer.h> > #include <linux/interrupt.h> > #include <linux/io.h> > #include <linux/irq.h> > @@ -136,6 +136,7 @@ struct jz4740_mmc_host { > struct platform_device *pdev; > struct jz4740_mmc_platform_data *pdata; > struct clk *clk; > + struct gpio_desc *power; > > enum jz4740_mmc_version version; > > @@ -903,18 +904,16 @@ static void jz4740_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) > switch (ios->power_mode) { > case MMC_POWER_UP: > jz4740_mmc_reset(host); > - if (host->pdata && gpio_is_valid(host->pdata->gpio_power)) > - gpio_set_value(host->pdata->gpio_power, > - !host->pdata->power_active_low); > + if (host->power) > + gpiod_set_value(host->power, 1); > host->cmdat |= JZ_MMC_CMDAT_INIT; > clk_prepare_enable(host->clk); > break; > case MMC_POWER_ON: > break; > default: > - if (host->pdata && gpio_is_valid(host->pdata->gpio_power)) > - gpio_set_value(host->pdata->gpio_power, > - host->pdata->power_active_low); > + if (host->power) > + gpiod_set_value(host->power, 0); > clk_disable_unprepare(host->clk); > break; > } > @@ -947,30 +946,9 @@ static const struct mmc_host_ops jz4740_mmc_ops = { > .enable_sdio_irq = jz4740_mmc_enable_sdio_irq, > }; > > -static int jz4740_mmc_request_gpio(struct device *dev, int gpio, > - const char *name, bool output, int value) > -{ > - int ret; > - > - if (!gpio_is_valid(gpio)) > - return 0; > - > - ret = gpio_request(gpio, name); > - if (ret) { > - dev_err(dev, "Failed to request %s gpio: %d\n", name, ret); > - return ret; > - } > - > - if (output) > - gpio_direction_output(gpio, value); > - else > - gpio_direction_input(gpio); > - > - return 0; > -} > - > -static int jz4740_mmc_request_gpios(struct mmc_host *mmc, > - struct platform_device *pdev) > +static int jz4740_mmc_request_gpios(struct jz4740_mmc_host *host, > + struct mmc_host *mmc, > + struct platform_device *pdev) > { > struct jz4740_mmc_platform_data *pdata = dev_get_platdata(&pdev->dev); > int ret = 0; > @@ -995,19 +973,12 @@ static int jz4740_mmc_request_gpios(struct mmc_host *mmc, > if (ret == -EPROBE_DEFER) > return ret; > > - return jz4740_mmc_request_gpio(&pdev->dev, pdata->gpio_power, > - "MMC read only", true, pdata->power_active_low); > -} > - > -static void jz4740_mmc_free_gpios(struct platform_device *pdev) > -{ > - struct jz4740_mmc_platform_data *pdata = dev_get_platdata(&pdev->dev); > - > - if (!pdata) > - return; > + host->power = devm_gpiod_get_optional(&pdev->dev, "power", > + GPIOD_OUT_HIGH); > + if (IS_ERR(host->power)) > + return PTR_ERR(host->power); > > - if (gpio_is_valid(pdata->gpio_power)) > - gpio_free(pdata->gpio_power); > + return 0; > } > > static const struct of_device_id jz4740_mmc_of_match[] = { > @@ -1053,7 +1024,7 @@ static int jz4740_mmc_probe(struct platform_device* pdev) > mmc->caps |= MMC_CAP_SDIO_IRQ; > if (!(pdata && pdata->data_1bit)) > mmc->caps |= MMC_CAP_4_BIT_DATA; > - ret = jz4740_mmc_request_gpios(mmc, pdev); > + ret = jz4740_mmc_request_gpios(host, mmc, pdev); > if (ret) > goto err_free_host; > } > @@ -1104,7 +1075,7 @@ static int jz4740_mmc_probe(struct platform_device* pdev) > dev_name(&pdev->dev), host); > if (ret) { > dev_err(&pdev->dev, "Failed to request irq: %d\n", ret); > - goto err_free_gpios; > + goto err_free_host; > } > > jz4740_mmc_clock_disable(host); > @@ -1135,8 +1106,6 @@ static int jz4740_mmc_probe(struct platform_device* pdev) > jz4740_mmc_release_dma_channels(host); > err_free_irq: > free_irq(host->irq, host); > -err_free_gpios: > - jz4740_mmc_free_gpios(pdev); > err_free_host: > mmc_free_host(mmc); > > @@ -1155,8 +1124,6 @@ static int jz4740_mmc_remove(struct platform_device *pdev) > > free_irq(host->irq, host); > > - jz4740_mmc_free_gpios(pdev); > - > if (host->use_dma) > jz4740_mmc_release_dma_channels(host); > > -- > 2.17.2 >
Le 2018-11-20 10:30, Ulf Hansson a écrit : > On 12 November 2018 at 15:12, Linus Walleij <linus.walleij@linaro.org> > wrote: >> The power GPIO line is passed with inversion flags and all from >> the platform data. Switch to using an optional GPIO descriptor and >> use this to switch the power. >> >> Augment the only boardfile to pass in the proper "power" descriptor >> in the GPIO descriptor machine table instead. >> >> As the GPIO handling is now much simpler, we can cut down on some >> overhead code. >> >> Cc: Paul Cercueil <paul@crapouillou.net> >> Cc: linux-mips@linux-mips.org >> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> > > Applied for next, thanks! > > Kind regards > Uffe Sorry for being late to the party. I would have NACK'd this :( I think the driver should just call mmc_regulator_get_supply() in the probe function, and then call mmc_regulator_set_ocr() to power ON or OFF the card. The board file would then provide the power regulator that triggers the GPIO line. -Paul >> --- >> .../mips/include/asm/mach-jz4740/jz4740_mmc.h | 2 - >> arch/mips/jz4740/board-qi_lb60.c | 6 +- >> drivers/mmc/host/jz4740_mmc.c | 65 >> +++++-------------- >> 3 files changed, 18 insertions(+), 55 deletions(-) >> >> diff --git a/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h >> b/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h >> index ff50aeb1a933..9a7de47c7c79 100644 >> --- a/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h >> +++ b/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h >> @@ -3,10 +3,8 @@ >> #define __LINUX_MMC_JZ4740_MMC >> >> struct jz4740_mmc_platform_data { >> - int gpio_power; >> unsigned card_detect_active_low:1; >> unsigned read_only_active_low:1; >> - unsigned power_active_low:1; >> >> unsigned data_1bit:1; >> }; >> diff --git a/arch/mips/jz4740/board-qi_lb60.c >> b/arch/mips/jz4740/board-qi_lb60.c >> index 705593d40d12..6718efb400f4 100644 >> --- a/arch/mips/jz4740/board-qi_lb60.c >> +++ b/arch/mips/jz4740/board-qi_lb60.c >> @@ -43,8 +43,6 @@ >> #include "clock.h" >> >> /* GPIOs */ >> -#define QI_LB60_GPIO_SD_VCC_EN_N JZ_GPIO_PORTD(2) >> - >> #define QI_LB60_GPIO_KEYOUT(x) (JZ_GPIO_PORTC(10) + (x)) >> #define QI_LB60_GPIO_KEYIN(x) (JZ_GPIO_PORTD(18) + (x)) >> #define QI_LB60_GPIO_KEYIN8 JZ_GPIO_PORTD(26) >> @@ -385,14 +383,14 @@ static struct platform_device qi_lb60_gpio_keys >> = { >> }; >> >> static struct jz4740_mmc_platform_data qi_lb60_mmc_pdata = { >> - .gpio_power = QI_LB60_GPIO_SD_VCC_EN_N, >> - .power_active_low = 1, >> + /* Intentionally left blank */ >> }; >> >> static struct gpiod_lookup_table qi_lb60_mmc_gpio_table = { >> .dev_id = "jz4740-mmc.0", >> .table = { >> GPIO_LOOKUP("GPIOD", 0, "cd", GPIO_ACTIVE_HIGH), >> + GPIO_LOOKUP("GPIOD", 2, "power", GPIO_ACTIVE_LOW), >> { }, >> }, >> }; >> diff --git a/drivers/mmc/host/jz4740_mmc.c >> b/drivers/mmc/host/jz4740_mmc.c >> index 44ea452add8e..6f7a99e54af0 100644 >> --- a/drivers/mmc/host/jz4740_mmc.c >> +++ b/drivers/mmc/host/jz4740_mmc.c >> @@ -21,7 +21,7 @@ >> #include <linux/dmaengine.h> >> #include <linux/dma-mapping.h> >> #include <linux/err.h> >> -#include <linux/gpio.h> >> +#include <linux/gpio/consumer.h> >> #include <linux/interrupt.h> >> #include <linux/io.h> >> #include <linux/irq.h> >> @@ -136,6 +136,7 @@ struct jz4740_mmc_host { >> struct platform_device *pdev; >> struct jz4740_mmc_platform_data *pdata; >> struct clk *clk; >> + struct gpio_desc *power; >> >> enum jz4740_mmc_version version; >> >> @@ -903,18 +904,16 @@ static void jz4740_mmc_set_ios(struct mmc_host >> *mmc, struct mmc_ios *ios) >> switch (ios->power_mode) { >> case MMC_POWER_UP: >> jz4740_mmc_reset(host); >> - if (host->pdata && >> gpio_is_valid(host->pdata->gpio_power)) >> - gpio_set_value(host->pdata->gpio_power, >> - >> !host->pdata->power_active_low); >> + if (host->power) >> + gpiod_set_value(host->power, 1); >> host->cmdat |= JZ_MMC_CMDAT_INIT; >> clk_prepare_enable(host->clk); >> break; >> case MMC_POWER_ON: >> break; >> default: >> - if (host->pdata && >> gpio_is_valid(host->pdata->gpio_power)) >> - gpio_set_value(host->pdata->gpio_power, >> - >> host->pdata->power_active_low); >> + if (host->power) >> + gpiod_set_value(host->power, 0); >> clk_disable_unprepare(host->clk); >> break; >> } >> @@ -947,30 +946,9 @@ static const struct mmc_host_ops jz4740_mmc_ops = >> { >> .enable_sdio_irq = jz4740_mmc_enable_sdio_irq, >> }; >> >> -static int jz4740_mmc_request_gpio(struct device *dev, int gpio, >> - const char *name, bool output, int value) >> -{ >> - int ret; >> - >> - if (!gpio_is_valid(gpio)) >> - return 0; >> - >> - ret = gpio_request(gpio, name); >> - if (ret) { >> - dev_err(dev, "Failed to request %s gpio: %d\n", name, >> ret); >> - return ret; >> - } >> - >> - if (output) >> - gpio_direction_output(gpio, value); >> - else >> - gpio_direction_input(gpio); >> - >> - return 0; >> -} >> - >> -static int jz4740_mmc_request_gpios(struct mmc_host *mmc, >> - struct platform_device *pdev) >> +static int jz4740_mmc_request_gpios(struct jz4740_mmc_host *host, >> + struct mmc_host *mmc, >> + struct platform_device *pdev) >> { >> struct jz4740_mmc_platform_data *pdata = >> dev_get_platdata(&pdev->dev); >> int ret = 0; >> @@ -995,19 +973,12 @@ static int jz4740_mmc_request_gpios(struct >> mmc_host *mmc, >> if (ret == -EPROBE_DEFER) >> return ret; >> >> - return jz4740_mmc_request_gpio(&pdev->dev, pdata->gpio_power, >> - "MMC read only", true, >> pdata->power_active_low); >> -} >> - >> -static void jz4740_mmc_free_gpios(struct platform_device *pdev) >> -{ >> - struct jz4740_mmc_platform_data *pdata = >> dev_get_platdata(&pdev->dev); >> - >> - if (!pdata) >> - return; >> + host->power = devm_gpiod_get_optional(&pdev->dev, "power", >> + GPIOD_OUT_HIGH); >> + if (IS_ERR(host->power)) >> + return PTR_ERR(host->power); >> >> - if (gpio_is_valid(pdata->gpio_power)) >> - gpio_free(pdata->gpio_power); >> + return 0; >> } >> >> static const struct of_device_id jz4740_mmc_of_match[] = { >> @@ -1053,7 +1024,7 @@ static int jz4740_mmc_probe(struct >> platform_device* pdev) >> mmc->caps |= MMC_CAP_SDIO_IRQ; >> if (!(pdata && pdata->data_1bit)) >> mmc->caps |= MMC_CAP_4_BIT_DATA; >> - ret = jz4740_mmc_request_gpios(mmc, pdev); >> + ret = jz4740_mmc_request_gpios(host, mmc, pdev); >> if (ret) >> goto err_free_host; >> } >> @@ -1104,7 +1075,7 @@ static int jz4740_mmc_probe(struct >> platform_device* pdev) >> dev_name(&pdev->dev), host); >> if (ret) { >> dev_err(&pdev->dev, "Failed to request irq: %d\n", >> ret); >> - goto err_free_gpios; >> + goto err_free_host; >> } >> >> jz4740_mmc_clock_disable(host); >> @@ -1135,8 +1106,6 @@ static int jz4740_mmc_probe(struct >> platform_device* pdev) >> jz4740_mmc_release_dma_channels(host); >> err_free_irq: >> free_irq(host->irq, host); >> -err_free_gpios: >> - jz4740_mmc_free_gpios(pdev); >> err_free_host: >> mmc_free_host(mmc); >> >> @@ -1155,8 +1124,6 @@ static int jz4740_mmc_remove(struct >> platform_device *pdev) >> >> free_irq(host->irq, host); >> >> - jz4740_mmc_free_gpios(pdev); >> - >> if (host->use_dma) >> jz4740_mmc_release_dma_channels(host); >> >> -- >> 2.17.2 >>
On Thu, Nov 22, 2018 at 5:26 PM Paul Cercueil <paul@crapouillou.net> wrote: > I think the driver should just call mmc_regulator_get_supply() in the > probe function, > and then call mmc_regulator_set_ocr() to power ON or OFF the card. The > board file would > then provide the power regulator that triggers the GPIO line. One does not exclude the other, feel free (or anyone else) to switch this to a fixed regulator. (Using descriptors!) I feel insecure about cold-coding that without being able to test it, I think I am on deep waters already. Someone with the proper hardware should do radical semantic patches like that. Introducing the regulator abstraction can lead to probe deferrals and whatnot. Yours, Linus Walleij
diff --git a/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h b/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h index ff50aeb1a933..9a7de47c7c79 100644 --- a/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h +++ b/arch/mips/include/asm/mach-jz4740/jz4740_mmc.h @@ -3,10 +3,8 @@ #define __LINUX_MMC_JZ4740_MMC struct jz4740_mmc_platform_data { - int gpio_power; unsigned card_detect_active_low:1; unsigned read_only_active_low:1; - unsigned power_active_low:1; unsigned data_1bit:1; }; diff --git a/arch/mips/jz4740/board-qi_lb60.c b/arch/mips/jz4740/board-qi_lb60.c index 705593d40d12..6718efb400f4 100644 --- a/arch/mips/jz4740/board-qi_lb60.c +++ b/arch/mips/jz4740/board-qi_lb60.c @@ -43,8 +43,6 @@ #include "clock.h" /* GPIOs */ -#define QI_LB60_GPIO_SD_VCC_EN_N JZ_GPIO_PORTD(2) - #define QI_LB60_GPIO_KEYOUT(x) (JZ_GPIO_PORTC(10) + (x)) #define QI_LB60_GPIO_KEYIN(x) (JZ_GPIO_PORTD(18) + (x)) #define QI_LB60_GPIO_KEYIN8 JZ_GPIO_PORTD(26) @@ -385,14 +383,14 @@ static struct platform_device qi_lb60_gpio_keys = { }; static struct jz4740_mmc_platform_data qi_lb60_mmc_pdata = { - .gpio_power = QI_LB60_GPIO_SD_VCC_EN_N, - .power_active_low = 1, + /* Intentionally left blank */ }; static struct gpiod_lookup_table qi_lb60_mmc_gpio_table = { .dev_id = "jz4740-mmc.0", .table = { GPIO_LOOKUP("GPIOD", 0, "cd", GPIO_ACTIVE_HIGH), + GPIO_LOOKUP("GPIOD", 2, "power", GPIO_ACTIVE_LOW), { }, }, }; diff --git a/drivers/mmc/host/jz4740_mmc.c b/drivers/mmc/host/jz4740_mmc.c index 44ea452add8e..6f7a99e54af0 100644 --- a/drivers/mmc/host/jz4740_mmc.c +++ b/drivers/mmc/host/jz4740_mmc.c @@ -21,7 +21,7 @@ #include <linux/dmaengine.h> #include <linux/dma-mapping.h> #include <linux/err.h> -#include <linux/gpio.h> +#include <linux/gpio/consumer.h> #include <linux/interrupt.h> #include <linux/io.h> #include <linux/irq.h> @@ -136,6 +136,7 @@ struct jz4740_mmc_host { struct platform_device *pdev; struct jz4740_mmc_platform_data *pdata; struct clk *clk; + struct gpio_desc *power; enum jz4740_mmc_version version; @@ -903,18 +904,16 @@ static void jz4740_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) switch (ios->power_mode) { case MMC_POWER_UP: jz4740_mmc_reset(host); - if (host->pdata && gpio_is_valid(host->pdata->gpio_power)) - gpio_set_value(host->pdata->gpio_power, - !host->pdata->power_active_low); + if (host->power) + gpiod_set_value(host->power, 1); host->cmdat |= JZ_MMC_CMDAT_INIT; clk_prepare_enable(host->clk); break; case MMC_POWER_ON: break; default: - if (host->pdata && gpio_is_valid(host->pdata->gpio_power)) - gpio_set_value(host->pdata->gpio_power, - host->pdata->power_active_low); + if (host->power) + gpiod_set_value(host->power, 0); clk_disable_unprepare(host->clk); break; } @@ -947,30 +946,9 @@ static const struct mmc_host_ops jz4740_mmc_ops = { .enable_sdio_irq = jz4740_mmc_enable_sdio_irq, }; -static int jz4740_mmc_request_gpio(struct device *dev, int gpio, - const char *name, bool output, int value) -{ - int ret; - - if (!gpio_is_valid(gpio)) - return 0; - - ret = gpio_request(gpio, name); - if (ret) { - dev_err(dev, "Failed to request %s gpio: %d\n", name, ret); - return ret; - } - - if (output) - gpio_direction_output(gpio, value); - else - gpio_direction_input(gpio); - - return 0; -} - -static int jz4740_mmc_request_gpios(struct mmc_host *mmc, - struct platform_device *pdev) +static int jz4740_mmc_request_gpios(struct jz4740_mmc_host *host, + struct mmc_host *mmc, + struct platform_device *pdev) { struct jz4740_mmc_platform_data *pdata = dev_get_platdata(&pdev->dev); int ret = 0; @@ -995,19 +973,12 @@ static int jz4740_mmc_request_gpios(struct mmc_host *mmc, if (ret == -EPROBE_DEFER) return ret; - return jz4740_mmc_request_gpio(&pdev->dev, pdata->gpio_power, - "MMC read only", true, pdata->power_active_low); -} - -static void jz4740_mmc_free_gpios(struct platform_device *pdev) -{ - struct jz4740_mmc_platform_data *pdata = dev_get_platdata(&pdev->dev); - - if (!pdata) - return; + host->power = devm_gpiod_get_optional(&pdev->dev, "power", + GPIOD_OUT_HIGH); + if (IS_ERR(host->power)) + return PTR_ERR(host->power); - if (gpio_is_valid(pdata->gpio_power)) - gpio_free(pdata->gpio_power); + return 0; } static const struct of_device_id jz4740_mmc_of_match[] = { @@ -1053,7 +1024,7 @@ static int jz4740_mmc_probe(struct platform_device* pdev) mmc->caps |= MMC_CAP_SDIO_IRQ; if (!(pdata && pdata->data_1bit)) mmc->caps |= MMC_CAP_4_BIT_DATA; - ret = jz4740_mmc_request_gpios(mmc, pdev); + ret = jz4740_mmc_request_gpios(host, mmc, pdev); if (ret) goto err_free_host; } @@ -1104,7 +1075,7 @@ static int jz4740_mmc_probe(struct platform_device* pdev) dev_name(&pdev->dev), host); if (ret) { dev_err(&pdev->dev, "Failed to request irq: %d\n", ret); - goto err_free_gpios; + goto err_free_host; } jz4740_mmc_clock_disable(host); @@ -1135,8 +1106,6 @@ static int jz4740_mmc_probe(struct platform_device* pdev) jz4740_mmc_release_dma_channels(host); err_free_irq: free_irq(host->irq, host); -err_free_gpios: - jz4740_mmc_free_gpios(pdev); err_free_host: mmc_free_host(mmc); @@ -1155,8 +1124,6 @@ static int jz4740_mmc_remove(struct platform_device *pdev) free_irq(host->irq, host); - jz4740_mmc_free_gpios(pdev); - if (host->use_dma) jz4740_mmc_release_dma_channels(host);
The power GPIO line is passed with inversion flags and all from the platform data. Switch to using an optional GPIO descriptor and use this to switch the power. Augment the only boardfile to pass in the proper "power" descriptor in the GPIO descriptor machine table instead. As the GPIO handling is now much simpler, we can cut down on some overhead code. Cc: Paul Cercueil <paul@crapouillou.net> Cc: linux-mips@linux-mips.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- .../mips/include/asm/mach-jz4740/jz4740_mmc.h | 2 - arch/mips/jz4740/board-qi_lb60.c | 6 +- drivers/mmc/host/jz4740_mmc.c | 65 +++++-------------- 3 files changed, 18 insertions(+), 55 deletions(-)