| Message ID | 20181122151834.6194-1-rui.silva@linaro.org (mailing list archive) |
|---|---|
| Headers | show |
| Series | media: staging/imx7: add i.MX7 media driver | expand |
On 11/22/2018 04:18 PM, Rui Miguel Silva wrote: > Hi, > This series introduces the Media driver to work with the i.MX7 SoC. it uses the > already existing imx media core drivers but since the i.MX7, contrary to > i.MX5/6, do not have an IPU and because of that some changes in the imx media > core are made along this series to make it support that case. > > This patches adds CSI and MIPI-CSI2 drivers for i.MX7, along with several > configurations changes for this to work as a capture subsystem. Some bugs are > also fixed along the line. And necessary documentation. > > For a more detailed view of the capture paths, pads links in the i.MX7 please > take a look at the documentation in PATCH 10. > > The system used to test and develop this was the Warp7 board with an OV2680 > sensor, which output format is 10-bit bayer. So, only MIPI interface was > tested, a scenario with an parallel input would nice to have. I got a few checkpatch warnings about coding style: CHECK: Alignment should match open parenthesis #953: FILE: drivers/staging/media/imx/imx7-media-csi.c:911: +static struct v4l2_mbus_framefmt *imx7_csi_get_format(struct imx7_csi *csi, + struct v4l2_subdev_pad_config *cfg, CHECK: Alignment should match open parenthesis #1341: FILE: drivers/staging/media/imx/imx7-media-csi.c:1299: + ret = v4l2_async_register_fwnode_subdev(&csi->sd, + sizeof(struct v4l2_async_subdev), CHECK: Lines should not end with a '(' #684: FILE: drivers/staging/media/imx/imx7-mipi-csis.c:669: +static struct csis_pix_format const *mipi_csis_try_format( CHECK: Alignment should match open parenthesis #708: FILE: drivers/staging/media/imx/imx7-mipi-csis.c:693: +static struct v4l2_mbus_framefmt *mipi_csis_get_format(struct csi_state *state, + struct v4l2_subdev_pad_config *cfg, CHECK: Alignment should match open parenthesis #936: FILE: drivers/staging/media/imx/imx7-mipi-csis.c:921: + ret = v4l2_async_register_fwnode_subdev(mipi_sd, + sizeof(struct v4l2_async_subdev), &sink_port, 1, Apparently the latest coding style is that alignment is more important than line length, although I personally do not agree. But since you need to respin in any case due to the wrong SPDX identifier you used you might as well take this into account. I was really hoping I could merge this, but the SPDX license issue killed it. Regards, Hans > > > Bellow goes an example of the output of the pads and links and the output of > v4l2-compliance testing. > > The v4l-utils version used is: > v4l2-compliance SHA : 044d5ab7b0d02683070d01a369c73d462d7a0cee from Nov 19th > > The Media Driver fail some tests but this failures are coming from code out of > scope of this series (imx-capture), and some from the sensor OV2680 > but that I think not related with the sensor driver but with the testing and > core. > > The csi and mipi-csi entities pass all compliance tests. > > Cheers, > Rui > > v8->v9: > Hans Verkuil: > - Fix issues detected by checkpatch strict, still some left: > - bigger kconfig option description > - some alignement parenthesis that were left as they are, to be more > readable > - added new patch (PATCH13) for Maintainers update > - SPDX in documentation rst file > Sakari Ailus: > - remove pad check in csi, this is done by core already > - destroy mutex in probe error path (add label) > - swap order in driver release > - initialize endpoint in stack > - use clk_bulk > kbuild test robot: > - add the missing imx-media-dev-common.c in patch 1/13 > - remove OWNER of module csis > Myself: > - add MAINTAINERS entries - new patch > > v7->v8: > Myself: > - rebase to latest linux-next (s/V4L2_MBUS_CSI2/V4L2_MBUS_CSI2_DPHY/) > - Rebuild and test with latest v4l2-compliance > - add Sakari reviewed-by tag to dt-bindings > > v6->v7: > Myself: > - Clock patches removed from this version since they were already merged > - Rebuild and test with the latest v4l2-compliance > - Add patch to video-mux regarding bayer formats > - remove reference to dependent patch serie (was already merged) > > Sakari Ailus: > - add port and endpoint explanantions > - fix some wording should -> shall > > v5->v6: > Rob Herring: > - rename power-domain node name from: pgc-power-domain to power-domain > - change mux-control-cells to 0 > - remove bus-width from mipi bindings and dts > - remove err... regarding clock names line > - remove clk-settle from example > - split mipi-csi2 and csi bindings per file > - add OF graph description to CSI > > Philipp Zabel: > - rework group IDs and rename them with an _IPU_ prefix, this allowed to remove > the ipu_present flag need. > > v4->v5: > Sakari Ailus: > - fix remove of the capture entries in dts bindings in the right patch > > Stephen Boyd: > - Send all series to clk list > > v3->v4: > Philipp Zabel: > - refactor initialization code from media device probe to be possible to used > from other modules > - Remove index of csi from all accurrencs (dts, code, documentation) > - Remove need for capture node for imx7 > - fix pinctrl for ov2680 > - add reviewed tag to add multiplexer controls patch > > Fabio Estevam: > - remove always on from new regulator > > Randy Dunlap: > - several text editing fixes in documentation > > Myself: > - rebase on top of v4 of Steve series > - change CSI probe to initialize imx media device > - remove csi mux parallel endpoint from mux to avoid warning message > > v2->v3: > Philipp Zabel: > - use of_match_device in imx-media-dev instead of of_device_match > - fix number of data lanes from 4 to 2 > - change the clock definitions and use of mipi > - move hs-settle from endpoint > > Rob Herring: > - fix phy-supply description > - add vendor properties > - fix examples indentations > > Stephen Boyd: patch 3/14 > - fix double sign-off > - add fixes tag > > Dong Aisheng: patch 3/14 > - fix double sign-off > - add Acked-by tag > > Shawn Guo: > patch 4/14 > - remove line breakage in parent redifiniton > - added Acked-by tag > > - dropped CMA area increase and add more verbose information in case of > dma allocation failure > patch 9/14 > - remove extra line between cells and reg masks > > Myself: > - rework on frame end in csi > - add rxcount in csi driver > - add power supplies to ov2680 node and fix gpio polarity > > v1->v2: > Dan Carpenter: > - fix return paths and codes; > - fix clk_frequency validation and return code; > - handle the csi remove (release resources that was missing) > - revert the logic arround the ipu_present flag > > Philipp Zabel: > - drop patch that changed the rgb formats and address the pixel/bus format in > mipi_csis code. > > MySelf: > - add patch that add ov2680 node to the warp7 dts, so the all data path is > complete. > - add linux-clk mailing list to the clock patches cc: > > v4l2-compliance SHA: 044d5ab7b0d02683070d01a369c73d462d7a0cee, 32 bits > > Compliance test for device /dev/media0: > > Media Driver Info: > Driver name : imx7-csi > Model : imx-media > Serial : > Bus info : > Media version : 4.20.0 > Hardware revision: 0x00000000 (0) > Driver version : 4.20.0 > > Required ioctls: > test MEDIA_IOC_DEVICE_INFO: OK > > Allow for multiple opens: > test second /dev/media0 open: OK > test MEDIA_IOC_DEVICE_INFO: OK > test for unlimited opens: OK > > Media Controller ioctls: > test MEDIA_IOC_G_TOPOLOGY: OK > Entities: 5 Interfaces: 5 Pads: 9 Links: 9 > test MEDIA_IOC_ENUM_ENTITIES/LINKS: OK > test MEDIA_IOC_SETUP_LINK: OK > > -------------------------------------------------------------------------------- > Compliance test for device /dev/video0: > > Driver Info: > Driver name : imx-media-captu > Card type : imx-media-capture > Bus info : platform:csi > Driver version : 4.20.0 > Capabilities : 0x84200001 > Video Capture > Streaming > Extended Pix Format > Device Capabilities > Device Caps : 0x04200001 > Video Capture > Streaming > Extended Pix Format > Media Driver Info: > Driver name : imx7-csi > Model : imx-media > Serial : > Bus info : > Media version : 4.20.0 > Hardware revision: 0x00000000 (0) > Driver version : 4.20.0 > Interface Info: > ID : 0x03000005 > Type : V4L Video > Entity Info: > ID : 0x00000004 (4) > Name : csi capture > Function : V4L2 I/O > Pad 0x01000007 : 0: Sink > Link 0x02000008: from remote pad 0x1000003 of entity 'csi': Data, Enabled > > Required ioctls: > test MC information (see 'Media Driver Info' above): OK > test VIDIOC_QUERYCAP: OK > > Allow for multiple opens: > test second /dev/video0 open: OK > test VIDIOC_QUERYCAP: OK > test VIDIOC_G/S_PRIORITY: OK > test for unlimited opens: OK > > Debug ioctls: > test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported) > test VIDIOC_LOG_STATUS: OK (Not Supported) > > Input ioctls: > test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) > test VIDIOC_ENUMAUDIO: OK (Not Supported) > fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-input-output.cpp(420): G_INPUT not supported for a capture dev > ice > test VIDIOC_G/S/ENUMINPUT: FAIL > test VIDIOC_G/S_AUDIO: OK (Not Supported) > Inputs: 0 Audio Inputs: 0 Tuners: 0 > > Output ioctls: > test VIDIOC_G/S_MODULATOR: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_ENUMAUDOUT: OK (Not Supported) > test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) > test VIDIOC_G/S_AUDOUT: OK (Not Supported) > Outputs: 0 Audio Outputs: 0 Modulators: 0 > > Input/Output configuration ioctls: > test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) > test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) > test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) > test VIDIOC_G/S_EDID: OK (Not Supported) > > Control ioctls: > test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK > test VIDIOC_QUERYCTRL: OK > test VIDIOC_G/S_CTRL: OK > test VIDIOC_G/S/TRY_EXT_CTRLS: OK > fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-controls.cpp(816): subscribe event for control 'User Controls' > failed > test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL > test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) > Standard Controls: 10 Private Controls: 0 > > Format ioctls: > test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK > test VIDIOC_G/S_PARM: OK (Not Supported) > test VIDIOC_G_FBUF: OK (Not Supported) > test VIDIOC_G_FMT: OK > test VIDIOC_TRY_FMT: OK > test VIDIOC_S_FMT: OK > test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) > test Cropping: OK (Not Supported) > test Composing: OK (Not Supported) > test Scaling: OK (Not Supported) > > Codec ioctls: > test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) > test VIDIOC_G_ENC_INDEX: OK (Not Supported) > test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) > > Buffer ioctls: > test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK > test VIDIOC_EXPBUF: OK > > -------------------------------------------------------------------------------- > Compliance test for device /dev/v4l-subdev0: > > Media Driver Info: > Driver name : imx7-csi > Model : imx-media > Serial : > Bus info : > Media version : 4.20.0 > Hardware revision: 0x00000000 (0) > Driver version : 4.20.0 > Interface Info: > ID : 0x03000019 > Type : V4L Sub-Device > Entity Info: > ID : 0x00000001 (1) > Name : csi > Function : Video Interface Bridge > Pad 0x01000002 : 0: Sink > Link 0x02000015: from remote pad 0x100000d of entity 'csi_mux': Data, Enabled > Pad 0x01000003 : 1: Source > Link 0x02000008: to remote pad 0x1000007 of entity 'csi capture': Data, Enabled > > Required ioctls: > test MC information (see 'Media Driver Info' above): OK > > Allow for multiple opens: > test second /dev/v4l-subdev0 open: OK > test for unlimited opens: OK > > Debug ioctls: > test VIDIOC_LOG_STATUS: OK (Not Supported) > > Input ioctls: > test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) > test VIDIOC_ENUMAUDIO: OK (Not Supported) > test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) > test VIDIOC_G/S_AUDIO: OK (Not Supported) > Inputs: 0 Audio Inputs: 0 Tuners: 0 > > Output ioctls: > test VIDIOC_G/S_MODULATOR: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_ENUMAUDOUT: OK (Not Supported) > test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) > test VIDIOC_G/S_AUDOUT: OK (Not Supported) > Outputs: 0 Audio Outputs: 0 Modulators: 0 > > Input/Output configuration ioctls: > test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) > test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) > test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) > test VIDIOC_G/S_EDID: OK (Not Supported) > > Sub-Device ioctls (Sink Pad 0): > test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK > test Try VIDIOC_SUBDEV_G/S_FMT: OK > test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK > test Active VIDIOC_SUBDEV_G/S_FMT: OK > test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) > > Sub-Device ioctls (Source Pad 1): > test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK > test Try VIDIOC_SUBDEV_G/S_FMT: OK > test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK > test Active VIDIOC_SUBDEV_G/S_FMT: OK > test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) > > Control ioctls: > test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK > test VIDIOC_QUERYCTRL: OK > test VIDIOC_G/S_CTRL: OK > test VIDIOC_G/S/TRY_EXT_CTRLS: OK > test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK (Not Supported) > test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) > Standard Controls: 0 Private Controls: 0 > > Format ioctls: > test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported) > test VIDIOC_G/S_PARM: OK (Not Supported) > test VIDIOC_G_FBUF: OK (Not Supported) > test VIDIOC_G_FMT: OK (Not Supported) > test VIDIOC_TRY_FMT: OK (Not Supported) > test VIDIOC_S_FMT: OK (Not Supported) > test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) > test Cropping: OK (Not Supported) > test Composing: OK (Not Supported) > test Scaling: OK (Not Supported) > > Codec ioctls: > test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) > test VIDIOC_G_ENC_INDEX: OK (Not Supported) > test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) > > Buffer ioctls: > test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported) > test VIDIOC_EXPBUF: OK (Not Supported) > > -------------------------------------------------------------------------------- > Compliance test for device /dev/v4l-subdev1: > > Media Driver Info: > Driver name : imx7-csi > Model : imx-media > Serial : > Bus info : > Media version : 4.20.0 > Hardware revision: 0x00000000 (0) > Driver version : 4.20.0 > Interface Info: > ID : 0x0300001b > Type : V4L Sub-Device > Entity Info: > ID : 0x0000000a (10) > Name : csi_mux > Function : Video Muxer > Pad 0x0100000b : 0: Sink > Pad 0x0100000c : 1: Sink > Link 0x02000013: from remote pad 0x1000010 of entity 'imx7-mipi-csis.0': Data, Enabled > Pad 0x0100000d : 2: Source > Link 0x02000015: to remote pad 0x1000002 of entity 'csi': Data, Enabled > > Required ioctls: > test MC information (see 'Media Driver Info' above): OK > > Allow for multiple opens: > test second /dev/v4l-subdev1 open: OK > test for unlimited opens: OK > > Debug ioctls: > test VIDIOC_LOG_STATUS: OK (Not Supported) > > Input ioctls: > test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) > test VIDIOC_ENUMAUDIO: OK (Not Supported) > test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) > test VIDIOC_G/S_AUDIO: OK (Not Supported) > Inputs: 0 Audio Inputs: 0 Tuners: 0 > > Output ioctls: > test VIDIOC_G/S_MODULATOR: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_ENUMAUDOUT: OK (Not Supported) > test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) > test VIDIOC_G/S_AUDOUT: OK (Not Supported) > Outputs: 0 Audio Outputs: 0 Modulators: 0 > > Input/Output configuration ioctls: > test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) > test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) > test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) > test VIDIOC_G/S_EDID: OK (Not Supported) > > Sub-Device ioctls (Sink Pad 0): > test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) > test Try VIDIOC_SUBDEV_G/S_FMT: OK > test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) > test Active VIDIOC_SUBDEV_G/S_FMT: OK > test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) > > Sub-Device ioctls (Sink Pad 1): > test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) > test Try VIDIOC_SUBDEV_G/S_FMT: OK > test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) > test Active VIDIOC_SUBDEV_G/S_FMT: OK > test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) > > Sub-Device ioctls (Source Pad 2): > test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) > fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(370): s_fmt.format.width != fmt.format.width > test Try VIDIOC_SUBDEV_G/S_FMT: FAIL > test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) > test Active VIDIOC_SUBDEV_G/S_FMT: OK > test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) > > Control ioctls: > test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK (Not Supported) > test VIDIOC_QUERYCTRL: OK (Not Supported) > test VIDIOC_G/S_CTRL: OK (Not Supported) > test VIDIOC_G/S/TRY_EXT_CTRLS: OK (Not Supported) > test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK (Not Supported) > test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) > Standard Controls: 0 Private Controls: 0 > > Format ioctls: > test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported) > test VIDIOC_G/S_PARM: OK (Not Supported) > test VIDIOC_G_FBUF: OK (Not Supported) > test VIDIOC_G_FMT: OK (Not Supported) > test VIDIOC_TRY_FMT: OK (Not Supported) > test VIDIOC_S_FMT: OK (Not Supported) > test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) > test Cropping: OK (Not Supported) > test Composing: OK (Not Supported) > test Scaling: OK (Not Supported) > > Codec ioctls: > test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) > test VIDIOC_G_ENC_INDEX: OK (Not Supported) > test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) > > Buffer ioctls: > test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported) > test VIDIOC_EXPBUF: OK (Not Supported) > > -------------------------------------------------------------------------------- > Compliance test for device /dev/v4l-subdev2: > > Media Driver Info: > Driver name : imx7-csi > Model : imx-media > Serial : > Bus info : > Media version : 4.20.0 > Hardware revision: 0x00000000 (0) > Driver version : 4.20.0 > Interface Info: > ID : 0x0300001d > Type : V4L Sub-Device > Entity Info: > ID : 0x0000000e (14) > Name : imx7-mipi-csis.0 > Function : Video Interface Bridge > Pad 0x0100000f : 0: Sink > Link 0x02000017: from remote pad 0x1000012 of entity 'ov2680 1-0036': Data, Enabled > Pad 0x01000010 : 1: Source > Link 0x02000013: to remote pad 0x100000c of entity 'csi_mux': Data, Enabled > > Required ioctls: > test MC information (see 'Media Driver Info' above): OK > > Allow for multiple opens: > test second /dev/v4l-subdev2 open: OK > test for unlimited opens: OK > > Debug ioctls: > test VIDIOC_LOG_STATUS: OK > > Input ioctls: > test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) > test VIDIOC_ENUMAUDIO: OK (Not Supported) > test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) > test VIDIOC_G/S_AUDIO: OK (Not Supported) > Inputs: 0 Audio Inputs: 0 Tuners: 0 > > Output ioctls: > test VIDIOC_G/S_MODULATOR: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_ENUMAUDOUT: OK (Not Supported) > test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) > test VIDIOC_G/S_AUDOUT: OK (Not Supported) > Outputs: 0 Audio Outputs: 0 Modulators: 0 > > Input/Output configuration ioctls: > test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) > test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) > test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) > test VIDIOC_G/S_EDID: OK (Not Supported) > > Sub-Device ioctls (Sink Pad 0): > test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) > test Try VIDIOC_SUBDEV_G/S_FMT: OK > test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) > test Active VIDIOC_SUBDEV_G/S_FMT: OK > test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) > > Sub-Device ioctls (Source Pad 1): > test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) > test Try VIDIOC_SUBDEV_G/S_FMT: OK > test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) > test Active VIDIOC_SUBDEV_G/S_FMT: OK > test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) > > Control ioctls: > test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK (Not Supported) > test VIDIOC_QUERYCTRL: OK (Not Supported) > test VIDIOC_G/S_CTRL: OK (Not Supported) > test VIDIOC_G/S/TRY_EXT_CTRLS: OK (Not Supported) > test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK (Not Supported) > test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) > Standard Controls: 0 Private Controls: 0 > > Format ioctls: > test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported) > test VIDIOC_G/S_PARM: OK (Not Supported) > test VIDIOC_G_FBUF: OK (Not Supported) > test VIDIOC_G_FMT: OK (Not Supported) > test VIDIOC_TRY_FMT: OK (Not Supported) > test VIDIOC_S_FMT: OK (Not Supported) > test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) > test Cropping: OK (Not Supported) > test Composing: OK (Not Supported) > test Scaling: OK (Not Supported) > > Codec ioctls: > test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) > test VIDIOC_G_ENC_INDEX: OK (Not Supported) > test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) > > Buffer ioctls: > test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported) > test VIDIOC_EXPBUF: OK (Not Supported) > > -------------------------------------------------------------------------------- > Compliance test for device /dev/v4l-subdev3: > > Media Driver Info: > Driver name : imx7-csi > Model : imx-media > Serial : > Bus info : > Media version : 4.20.0 > Hardware revision: 0x00000000 (0) > Driver version : 4.20.0 > Interface Info: > ID : 0x0300001f > Type : V4L Sub-Device > Entity Info: > ID : 0x00000011 (17) > Name : ov2680 1-0036 > Function : Camera Sensor > Pad 0x01000012 : 0: Source > Link 0x02000017: to remote pad 0x100000f of entity 'imx7-mipi-csis.0': Data, Enabled > > Required ioctls: > test MC information (see 'Media Driver Info' above): OK > > Allow for multiple opens: > test second /dev/v4l-subdev3 open: OK > test for unlimited opens: OK > > Debug ioctls: > test VIDIOC_LOG_STATUS: OK (Not Supported) > > Input ioctls: > test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) > test VIDIOC_ENUMAUDIO: OK (Not Supported) > test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) > test VIDIOC_G/S_AUDIO: OK (Not Supported) > Inputs: 0 Audio Inputs: 0 Tuners: 0 > > Output ioctls: > test VIDIOC_G/S_MODULATOR: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_ENUMAUDOUT: OK (Not Supported) > test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) > test VIDIOC_G/S_AUDOUT: OK (Not Supported) > Outputs: 0 Audio Outputs: 0 Modulators: 0 > > Input/Output configuration ioctls: > test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) > test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) > test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) > test VIDIOC_G/S_EDID: OK (Not Supported) > > Sub-Device ioctls (Source Pad 0): > fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(57): node->enum_frame_interval_pad >= 0 > fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(183): ret && ret != ENOTTY > fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(248): ret && ret != ENOTTY > test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: FAIL > fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(311): fmt.width == 0 || fmt.width > 65536 > fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(356): checkMBusFrameFmt(node, fmt.format) > test Try VIDIOC_SUBDEV_G/S_FMT: FAIL > test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK > test Active VIDIOC_SUBDEV_G/S_FMT: OK > test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) > test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK > > Control ioctls: > test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK > test VIDIOC_QUERYCTRL: OK > test VIDIOC_G/S_CTRL: OK > test VIDIOC_G/S/TRY_EXT_CTRLS: OK > fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-controls.cpp(816): subscribe event for control 'User Controls' > failed > test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL > test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) > Standard Controls: 10 Private Controls: 0 > > Format ioctls: > test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported) > test VIDIOC_G/S_PARM: OK (Not Supported) > test VIDIOC_G_FBUF: OK (Not Supported) > test VIDIOC_G_FMT: OK (Not Supported) > test VIDIOC_TRY_FMT: OK (Not Supported) > test VIDIOC_S_FMT: OK (Not Supported) > test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) > test Cropping: OK (Not Supported) > test Composing: OK (Not Supported) > test Scaling: OK (Not Supported) > > Codec ioctls: > test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) > test VIDIOC_G_ENC_INDEX: OK (Not Supported) > test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) > > Buffer ioctls: > test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported) > test VIDIOC_EXPBUF: OK (Not Supported) > > Total: 267, Succeeded: 261, Failed: 6, Warnings: 0 > > Rui Miguel Silva (13): > media: staging/imx: refactor imx media device probe > media: staging/imx: rearrange group id to take in account IPU > media: staging/imx7: add imx7 CSI subdev driver > media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7 > media: dt-bindings: add bindings for i.MX7 media driver > ARM: dts: imx7s: add mipi phy power domain > ARM: dts: imx7s: add multiplexer controls > ARM: dts: imx7: Add video mux, csi and mipi_csi and connections > ARM: dts: imx7s-warp: add ov2680 sensor node > media: imx7.rst: add documentation for i.MX7 media driver > media: staging/imx: add i.MX7 entries to TODO file > media: video-mux: add bayer formats > media: MAINTAINERS: add entry for Freescale i.MX7 media driver > > .../devicetree/bindings/media/imx7-csi.txt | 45 + > .../bindings/media/imx7-mipi-csi2.txt | 90 ++ > Documentation/media/v4l-drivers/imx7.rst | 157 ++ > Documentation/media/v4l-drivers/index.rst | 1 + > MAINTAINERS | 11 + > arch/arm/boot/dts/imx7s-warp.dts | 95 ++ > arch/arm/boot/dts/imx7s.dtsi | 44 +- > drivers/media/platform/video-mux.c | 20 + > drivers/staging/media/imx/Kconfig | 9 +- > drivers/staging/media/imx/Makefile | 4 + > drivers/staging/media/imx/TODO | 9 + > drivers/staging/media/imx/imx-ic-common.c | 6 +- > drivers/staging/media/imx/imx-ic-prp.c | 16 +- > drivers/staging/media/imx/imx-media-csi.c | 6 +- > .../staging/media/imx/imx-media-dev-common.c | 102 ++ > drivers/staging/media/imx/imx-media-dev.c | 110 +- > .../staging/media/imx/imx-media-internal-sd.c | 20 +- > drivers/staging/media/imx/imx-media-of.c | 6 +- > drivers/staging/media/imx/imx-media-utils.c | 12 +- > drivers/staging/media/imx/imx-media.h | 38 +- > drivers/staging/media/imx/imx7-media-csi.c | 1354 +++++++++++++++++ > drivers/staging/media/imx/imx7-mipi-csis.c | 1135 ++++++++++++++ > 22 files changed, 3166 insertions(+), 124 deletions(-) > create mode 100644 Documentation/devicetree/bindings/media/imx7-csi.txt > create mode 100644 Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt > create mode 100644 Documentation/media/v4l-drivers/imx7.rst > create mode 100644 drivers/staging/media/imx/imx-media-dev-common.c > create mode 100644 drivers/staging/media/imx/imx7-media-csi.c > create mode 100644 drivers/staging/media/imx/imx7-mipi-csis.c >
On Fri, Dec 07, 2018 at 01:44:00PM +0100, Hans Verkuil wrote: > CHECK: Alignment should match open parenthesis > #936: FILE: drivers/staging/media/imx/imx7-mipi-csis.c:921: > + ret = v4l2_async_register_fwnode_subdev(mipi_sd, > + sizeof(struct v4l2_async_subdev), &sink_port, 1, > > Apparently the latest coding style is that alignment is more important than > line length, although I personally do not agree. But since you need to > respin in any case due to the wrong SPDX identifier you used you might as > well take this into account. I'm pretty sure it complains about both equally. If you make fix one warning it will complain about the other. So you just have to pick which warning to not care about. regards, dan carpenter
Hi Hans and Dan, On Fri 07 Dec 2018 at 13:38, Dan Carpenter wrote: > On Fri, Dec 07, 2018 at 01:44:00PM +0100, Hans Verkuil wrote: >> CHECK: Alignment should match open parenthesis >> #936: FILE: drivers/staging/media/imx/imx7-mipi-csis.c:921: >> + ret = v4l2_async_register_fwnode_subdev(mipi_sd, >> + sizeof(struct >> v4l2_async_subdev), &sink_port, 1, >> >> Apparently the latest coding style is that alignment is more >> important than >> line length, although I personally do not agree. But since you >> need to >> respin in any case due to the wrong SPDX identifier you used >> you might as >> well take this into account. I added this in the cover letter: - some alignment parenthesis that were left as they are, to be more readable this ones were left as they are as they seem impossible to fit all rules. I hope you really do not mind about this checks. if you have a strong opinion about this let me know, otherwise I will leave this as it is. > > I'm pretty sure it complains about both equally. If you make > fix one > warning it will complain about the other. So you just have to > pick > which warning to not care about. Yeah, I agree with you, I normally like to avoid at all cost the line length issue. --- Cheers, Rui > > regards, > dan carpenter
Hi Rui, On Fri, Dec 7, 2018 at 10:44 AM Hans Verkuil <hverkuil@xs4all.nl> wrote: > I got a few checkpatch warnings about coding style: > > CHECK: Alignment should match open parenthesis > #953: FILE: drivers/staging/media/imx/imx7-media-csi.c:911: > +static struct v4l2_mbus_framefmt *imx7_csi_get_format(struct imx7_csi *csi, > + struct v4l2_subdev_pad_config *cfg, > > CHECK: Alignment should match open parenthesis > #1341: FILE: drivers/staging/media/imx/imx7-media-csi.c:1299: > + ret = v4l2_async_register_fwnode_subdev(&csi->sd, > + sizeof(struct v4l2_async_subdev), > > CHECK: Lines should not end with a '(' > #684: FILE: drivers/staging/media/imx/imx7-mipi-csis.c:669: > +static struct csis_pix_format const *mipi_csis_try_format( > > CHECK: Alignment should match open parenthesis > #708: FILE: drivers/staging/media/imx/imx7-mipi-csis.c:693: > +static struct v4l2_mbus_framefmt *mipi_csis_get_format(struct csi_state *state, > + struct v4l2_subdev_pad_config *cfg, > > CHECK: Alignment should match open parenthesis > #936: FILE: drivers/staging/media/imx/imx7-mipi-csis.c:921: > + ret = v4l2_async_register_fwnode_subdev(mipi_sd, > + sizeof(struct v4l2_async_subdev), &sink_port, 1, > > Apparently the latest coding style is that alignment is more important than > line length, although I personally do not agree. But since you need to > respin in any case due to the wrong SPDX identifier you used you might as > well take this into account. > > I was really hoping I could merge this, but the SPDX license issue killed it. Do you plan to submit a new version? Thanks
Oi Fabio, On Fri 18 Jan 2019 at 16:49, Fabio Estevam wrote: > Hi Rui, > > On Fri, Dec 7, 2018 at 10:44 AM Hans Verkuil > <hverkuil@xs4all.nl> wrote: > >> I got a few checkpatch warnings about coding style: >> >> CHECK: Alignment should match open parenthesis >> #953: FILE: drivers/staging/media/imx/imx7-media-csi.c:911: >> +static struct v4l2_mbus_framefmt *imx7_csi_get_format(struct >> imx7_csi *csi, >> + struct >> v4l2_subdev_pad_config *cfg, >> >> CHECK: Alignment should match open parenthesis >> #1341: FILE: drivers/staging/media/imx/imx7-media-csi.c:1299: >> + ret = v4l2_async_register_fwnode_subdev(&csi->sd, >> + sizeof(struct >> v4l2_async_subdev), >> >> CHECK: Lines should not end with a '(' >> #684: FILE: drivers/staging/media/imx/imx7-mipi-csis.c:669: >> +static struct csis_pix_format const *mipi_csis_try_format( >> >> CHECK: Alignment should match open parenthesis >> #708: FILE: drivers/staging/media/imx/imx7-mipi-csis.c:693: >> +static struct v4l2_mbus_framefmt *mipi_csis_get_format(struct >> csi_state *state, >> + struct >> v4l2_subdev_pad_config *cfg, >> >> CHECK: Alignment should match open parenthesis >> #936: FILE: drivers/staging/media/imx/imx7-mipi-csis.c:921: >> + ret = v4l2_async_register_fwnode_subdev(mipi_sd, >> + sizeof(struct >> v4l2_async_subdev), &sink_port, 1, >> >> Apparently the latest coding style is that alignment is more >> important than >> line length, although I personally do not agree. But since you >> need to >> respin in any case due to the wrong SPDX identifier you used >> you might as >> well take this into account. >> >> I was really hoping I could merge this, but the SPDX license >> issue killed it. > > Do you plan to submit a new version? Yeah, I will try to send one next week. I think have all this addressed in a branch, I will need to rebase again. --- Cheers, Rui
Hi, This series introduces the Media driver to work with the i.MX7 SoC. it uses the already existing imx media core drivers but since the i.MX7, contrary to i.MX5/6, do not have an IPU and because of that some changes in the imx media core are made along this series to make it support that case. This patches adds CSI and MIPI-CSI2 drivers for i.MX7, along with several configurations changes for this to work as a capture subsystem. Some bugs are also fixed along the line. And necessary documentation. For a more detailed view of the capture paths, pads links in the i.MX7 please take a look at the documentation in PATCH 10. The system used to test and develop this was the Warp7 board with an OV2680 sensor, which output format is 10-bit bayer. So, only MIPI interface was tested, a scenario with an parallel input would nice to have. Bellow goes an example of the output of the pads and links and the output of v4l2-compliance testing. The v4l-utils version used is: v4l2-compliance SHA : 044d5ab7b0d02683070d01a369c73d462d7a0cee from Nov 19th The Media Driver fail some tests but this failures are coming from code out of scope of this series (imx-capture), and some from the sensor OV2680 but that I think not related with the sensor driver but with the testing and core. The csi and mipi-csi entities pass all compliance tests. Cheers, Rui v8->v9: Hans Verkuil: - Fix issues detected by checkpatch strict, still some left: - bigger kconfig option description - some alignement parenthesis that were left as they are, to be more readable - added new patch (PATCH13) for Maintainers update - SPDX in documentation rst file Sakari Ailus: - remove pad check in csi, this is done by core already - destroy mutex in probe error path (add label) - swap order in driver release - initialize endpoint in stack - use clk_bulk kbuild test robot: - add the missing imx-media-dev-common.c in patch 1/13 - remove OWNER of module csis Myself: - add MAINTAINERS entries - new patch v7->v8: Myself: - rebase to latest linux-next (s/V4L2_MBUS_CSI2/V4L2_MBUS_CSI2_DPHY/) - Rebuild and test with latest v4l2-compliance - add Sakari reviewed-by tag to dt-bindings v6->v7: Myself: - Clock patches removed from this version since they were already merged - Rebuild and test with the latest v4l2-compliance - Add patch to video-mux regarding bayer formats - remove reference to dependent patch serie (was already merged) Sakari Ailus: - add port and endpoint explanantions - fix some wording should -> shall v5->v6: Rob Herring: - rename power-domain node name from: pgc-power-domain to power-domain - change mux-control-cells to 0 - remove bus-width from mipi bindings and dts - remove err... regarding clock names line - remove clk-settle from example - split mipi-csi2 and csi bindings per file - add OF graph description to CSI Philipp Zabel: - rework group IDs and rename them with an _IPU_ prefix, this allowed to remove the ipu_present flag need. v4->v5: Sakari Ailus: - fix remove of the capture entries in dts bindings in the right patch Stephen Boyd: - Send all series to clk list v3->v4: Philipp Zabel: - refactor initialization code from media device probe to be possible to used from other modules - Remove index of csi from all accurrencs (dts, code, documentation) - Remove need for capture node for imx7 - fix pinctrl for ov2680 - add reviewed tag to add multiplexer controls patch Fabio Estevam: - remove always on from new regulator Randy Dunlap: - several text editing fixes in documentation Myself: - rebase on top of v4 of Steve series - change CSI probe to initialize imx media device - remove csi mux parallel endpoint from mux to avoid warning message v2->v3: Philipp Zabel: - use of_match_device in imx-media-dev instead of of_device_match - fix number of data lanes from 4 to 2 - change the clock definitions and use of mipi - move hs-settle from endpoint Rob Herring: - fix phy-supply description - add vendor properties - fix examples indentations Stephen Boyd: patch 3/14 - fix double sign-off - add fixes tag Dong Aisheng: patch 3/14 - fix double sign-off - add Acked-by tag Shawn Guo: patch 4/14 - remove line breakage in parent redifiniton - added Acked-by tag - dropped CMA area increase and add more verbose information in case of dma allocation failure patch 9/14 - remove extra line between cells and reg masks Myself: - rework on frame end in csi - add rxcount in csi driver - add power supplies to ov2680 node and fix gpio polarity v1->v2: Dan Carpenter: - fix return paths and codes; - fix clk_frequency validation and return code; - handle the csi remove (release resources that was missing) - revert the logic arround the ipu_present flag Philipp Zabel: - drop patch that changed the rgb formats and address the pixel/bus format in mipi_csis code. MySelf: - add patch that add ov2680 node to the warp7 dts, so the all data path is complete. - add linux-clk mailing list to the clock patches cc: v4l2-compliance SHA: 044d5ab7b0d02683070d01a369c73d462d7a0cee, 32 bits Compliance test for device /dev/media0: Media Driver Info: Driver name : imx7-csi Model : imx-media Serial : Bus info : Media version : 4.20.0 Hardware revision: 0x00000000 (0) Driver version : 4.20.0 Required ioctls: test MEDIA_IOC_DEVICE_INFO: OK Allow for multiple opens: test second /dev/media0 open: OK test MEDIA_IOC_DEVICE_INFO: OK test for unlimited opens: OK Media Controller ioctls: test MEDIA_IOC_G_TOPOLOGY: OK Entities: 5 Interfaces: 5 Pads: 9 Links: 9 test MEDIA_IOC_ENUM_ENTITIES/LINKS: OK test MEDIA_IOC_SETUP_LINK: OK -------------------------------------------------------------------------------- Compliance test for device /dev/video0: Driver Info: Driver name : imx-media-captu Card type : imx-media-capture Bus info : platform:csi Driver version : 4.20.0 Capabilities : 0x84200001 Video Capture Streaming Extended Pix Format Device Capabilities Device Caps : 0x04200001 Video Capture Streaming Extended Pix Format Media Driver Info: Driver name : imx7-csi Model : imx-media Serial : Bus info : Media version : 4.20.0 Hardware revision: 0x00000000 (0) Driver version : 4.20.0 Interface Info: ID : 0x03000005 Type : V4L Video Entity Info: ID : 0x00000004 (4) Name : csi capture Function : V4L2 I/O Pad 0x01000007 : 0: Sink Link 0x02000008: from remote pad 0x1000003 of entity 'csi': Data, Enabled Required ioctls: test MC information (see 'Media Driver Info' above): OK test VIDIOC_QUERYCAP: OK Allow for multiple opens: test second /dev/video0 open: OK test VIDIOC_QUERYCAP: OK test VIDIOC_G/S_PRIORITY: OK test for unlimited opens: OK Debug ioctls: test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported) test VIDIOC_LOG_STATUS: OK (Not Supported) Input ioctls: test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) test VIDIOC_ENUMAUDIO: OK (Not Supported) fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-input-output.cpp(420): G_INPUT not supported for a capture dev ice test VIDIOC_G/S/ENUMINPUT: FAIL test VIDIOC_G/S_AUDIO: OK (Not Supported) Inputs: 0 Audio Inputs: 0 Tuners: 0 Output ioctls: test VIDIOC_G/S_MODULATOR: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_ENUMAUDOUT: OK (Not Supported) test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) test VIDIOC_G/S_AUDOUT: OK (Not Supported) Outputs: 0 Audio Outputs: 0 Modulators: 0 Input/Output configuration ioctls: test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) test VIDIOC_G/S_EDID: OK (Not Supported) Control ioctls: test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK test VIDIOC_QUERYCTRL: OK test VIDIOC_G/S_CTRL: OK test VIDIOC_G/S/TRY_EXT_CTRLS: OK fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-controls.cpp(816): subscribe event for control 'User Controls' failed test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 10 Private Controls: 0 Format ioctls: test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK test VIDIOC_G/S_PARM: OK (Not Supported) test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK test VIDIOC_TRY_FMT: OK test VIDIOC_S_FMT: OK test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) test Cropping: OK (Not Supported) test Composing: OK (Not Supported) test Scaling: OK (Not Supported) Codec ioctls: test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) Buffer ioctls: test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK test VIDIOC_EXPBUF: OK -------------------------------------------------------------------------------- Compliance test for device /dev/v4l-subdev0: Media Driver Info: Driver name : imx7-csi Model : imx-media Serial : Bus info : Media version : 4.20.0 Hardware revision: 0x00000000 (0) Driver version : 4.20.0 Interface Info: ID : 0x03000019 Type : V4L Sub-Device Entity Info: ID : 0x00000001 (1) Name : csi Function : Video Interface Bridge Pad 0x01000002 : 0: Sink Link 0x02000015: from remote pad 0x100000d of entity 'csi_mux': Data, Enabled Pad 0x01000003 : 1: Source Link 0x02000008: to remote pad 0x1000007 of entity 'csi capture': Data, Enabled Required ioctls: test MC information (see 'Media Driver Info' above): OK Allow for multiple opens: test second /dev/v4l-subdev0 open: OK test for unlimited opens: OK Debug ioctls: test VIDIOC_LOG_STATUS: OK (Not Supported) Input ioctls: test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) test VIDIOC_ENUMAUDIO: OK (Not Supported) test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) test VIDIOC_G/S_AUDIO: OK (Not Supported) Inputs: 0 Audio Inputs: 0 Tuners: 0 Output ioctls: test VIDIOC_G/S_MODULATOR: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_ENUMAUDOUT: OK (Not Supported) test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) test VIDIOC_G/S_AUDOUT: OK (Not Supported) Outputs: 0 Audio Outputs: 0 Modulators: 0 Input/Output configuration ioctls: test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) test VIDIOC_G/S_EDID: OK (Not Supported) Sub-Device ioctls (Sink Pad 0): test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK test Try VIDIOC_SUBDEV_G/S_FMT: OK test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK test Active VIDIOC_SUBDEV_G/S_FMT: OK test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) Sub-Device ioctls (Source Pad 1): test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK test Try VIDIOC_SUBDEV_G/S_FMT: OK test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK test Active VIDIOC_SUBDEV_G/S_FMT: OK test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) Control ioctls: test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK test VIDIOC_QUERYCTRL: OK test VIDIOC_G/S_CTRL: OK test VIDIOC_G/S/TRY_EXT_CTRLS: OK test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK (Not Supported) test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 0 Private Controls: 0 Format ioctls: test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported) test VIDIOC_G/S_PARM: OK (Not Supported) test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK (Not Supported) test VIDIOC_TRY_FMT: OK (Not Supported) test VIDIOC_S_FMT: OK (Not Supported) test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) test Cropping: OK (Not Supported) test Composing: OK (Not Supported) test Scaling: OK (Not Supported) Codec ioctls: test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) Buffer ioctls: test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported) test VIDIOC_EXPBUF: OK (Not Supported) -------------------------------------------------------------------------------- Compliance test for device /dev/v4l-subdev1: Media Driver Info: Driver name : imx7-csi Model : imx-media Serial : Bus info : Media version : 4.20.0 Hardware revision: 0x00000000 (0) Driver version : 4.20.0 Interface Info: ID : 0x0300001b Type : V4L Sub-Device Entity Info: ID : 0x0000000a (10) Name : csi_mux Function : Video Muxer Pad 0x0100000b : 0: Sink Pad 0x0100000c : 1: Sink Link 0x02000013: from remote pad 0x1000010 of entity 'imx7-mipi-csis.0': Data, Enabled Pad 0x0100000d : 2: Source Link 0x02000015: to remote pad 0x1000002 of entity 'csi': Data, Enabled Required ioctls: test MC information (see 'Media Driver Info' above): OK Allow for multiple opens: test second /dev/v4l-subdev1 open: OK test for unlimited opens: OK Debug ioctls: test VIDIOC_LOG_STATUS: OK (Not Supported) Input ioctls: test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) test VIDIOC_ENUMAUDIO: OK (Not Supported) test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) test VIDIOC_G/S_AUDIO: OK (Not Supported) Inputs: 0 Audio Inputs: 0 Tuners: 0 Output ioctls: test VIDIOC_G/S_MODULATOR: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_ENUMAUDOUT: OK (Not Supported) test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) test VIDIOC_G/S_AUDOUT: OK (Not Supported) Outputs: 0 Audio Outputs: 0 Modulators: 0 Input/Output configuration ioctls: test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) test VIDIOC_G/S_EDID: OK (Not Supported) Sub-Device ioctls (Sink Pad 0): test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) test Try VIDIOC_SUBDEV_G/S_FMT: OK test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) test Active VIDIOC_SUBDEV_G/S_FMT: OK test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) Sub-Device ioctls (Sink Pad 1): test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) test Try VIDIOC_SUBDEV_G/S_FMT: OK test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) test Active VIDIOC_SUBDEV_G/S_FMT: OK test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) Sub-Device ioctls (Source Pad 2): test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(370): s_fmt.format.width != fmt.format.width test Try VIDIOC_SUBDEV_G/S_FMT: FAIL test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) test Active VIDIOC_SUBDEV_G/S_FMT: OK test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) Control ioctls: test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK (Not Supported) test VIDIOC_QUERYCTRL: OK (Not Supported) test VIDIOC_G/S_CTRL: OK (Not Supported) test VIDIOC_G/S/TRY_EXT_CTRLS: OK (Not Supported) test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK (Not Supported) test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 0 Private Controls: 0 Format ioctls: test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported) test VIDIOC_G/S_PARM: OK (Not Supported) test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK (Not Supported) test VIDIOC_TRY_FMT: OK (Not Supported) test VIDIOC_S_FMT: OK (Not Supported) test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) test Cropping: OK (Not Supported) test Composing: OK (Not Supported) test Scaling: OK (Not Supported) Codec ioctls: test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) Buffer ioctls: test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported) test VIDIOC_EXPBUF: OK (Not Supported) -------------------------------------------------------------------------------- Compliance test for device /dev/v4l-subdev2: Media Driver Info: Driver name : imx7-csi Model : imx-media Serial : Bus info : Media version : 4.20.0 Hardware revision: 0x00000000 (0) Driver version : 4.20.0 Interface Info: ID : 0x0300001d Type : V4L Sub-Device Entity Info: ID : 0x0000000e (14) Name : imx7-mipi-csis.0 Function : Video Interface Bridge Pad 0x0100000f : 0: Sink Link 0x02000017: from remote pad 0x1000012 of entity 'ov2680 1-0036': Data, Enabled Pad 0x01000010 : 1: Source Link 0x02000013: to remote pad 0x100000c of entity 'csi_mux': Data, Enabled Required ioctls: test MC information (see 'Media Driver Info' above): OK Allow for multiple opens: test second /dev/v4l-subdev2 open: OK test for unlimited opens: OK Debug ioctls: test VIDIOC_LOG_STATUS: OK Input ioctls: test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) test VIDIOC_ENUMAUDIO: OK (Not Supported) test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) test VIDIOC_G/S_AUDIO: OK (Not Supported) Inputs: 0 Audio Inputs: 0 Tuners: 0 Output ioctls: test VIDIOC_G/S_MODULATOR: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_ENUMAUDOUT: OK (Not Supported) test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) test VIDIOC_G/S_AUDOUT: OK (Not Supported) Outputs: 0 Audio Outputs: 0 Modulators: 0 Input/Output configuration ioctls: test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) test VIDIOC_G/S_EDID: OK (Not Supported) Sub-Device ioctls (Sink Pad 0): test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) test Try VIDIOC_SUBDEV_G/S_FMT: OK test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) test Active VIDIOC_SUBDEV_G/S_FMT: OK test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) Sub-Device ioctls (Source Pad 1): test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) test Try VIDIOC_SUBDEV_G/S_FMT: OK test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK (Not Supported) test Active VIDIOC_SUBDEV_G/S_FMT: OK test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK (Not Supported) Control ioctls: test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK (Not Supported) test VIDIOC_QUERYCTRL: OK (Not Supported) test VIDIOC_G/S_CTRL: OK (Not Supported) test VIDIOC_G/S/TRY_EXT_CTRLS: OK (Not Supported) test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK (Not Supported) test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 0 Private Controls: 0 Format ioctls: test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported) test VIDIOC_G/S_PARM: OK (Not Supported) test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK (Not Supported) test VIDIOC_TRY_FMT: OK (Not Supported) test VIDIOC_S_FMT: OK (Not Supported) test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) test Cropping: OK (Not Supported) test Composing: OK (Not Supported) test Scaling: OK (Not Supported) Codec ioctls: test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) Buffer ioctls: test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported) test VIDIOC_EXPBUF: OK (Not Supported) -------------------------------------------------------------------------------- Compliance test for device /dev/v4l-subdev3: Media Driver Info: Driver name : imx7-csi Model : imx-media Serial : Bus info : Media version : 4.20.0 Hardware revision: 0x00000000 (0) Driver version : 4.20.0 Interface Info: ID : 0x0300001f Type : V4L Sub-Device Entity Info: ID : 0x00000011 (17) Name : ov2680 1-0036 Function : Camera Sensor Pad 0x01000012 : 0: Source Link 0x02000017: to remote pad 0x100000f of entity 'imx7-mipi-csis.0': Data, Enabled Required ioctls: test MC information (see 'Media Driver Info' above): OK Allow for multiple opens: test second /dev/v4l-subdev3 open: OK test for unlimited opens: OK Debug ioctls: test VIDIOC_LOG_STATUS: OK (Not Supported) Input ioctls: test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) test VIDIOC_ENUMAUDIO: OK (Not Supported) test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) test VIDIOC_G/S_AUDIO: OK (Not Supported) Inputs: 0 Audio Inputs: 0 Tuners: 0 Output ioctls: test VIDIOC_G/S_MODULATOR: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_ENUMAUDOUT: OK (Not Supported) test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) test VIDIOC_G/S_AUDOUT: OK (Not Supported) Outputs: 0 Audio Outputs: 0 Modulators: 0 Input/Output configuration ioctls: test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) test VIDIOC_G/S_EDID: OK (Not Supported) Sub-Device ioctls (Source Pad 0): fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(57): node->enum_frame_interval_pad >= 0 fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(183): ret && ret != ENOTTY fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(248): ret && ret != ENOTTY test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: FAIL fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(311): fmt.width == 0 || fmt.width > 65536 fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-subdevs.cpp(356): checkMBusFrameFmt(node, fmt.format) test Try VIDIOC_SUBDEV_G/S_FMT: FAIL test Try VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test Active VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: OK test Active VIDIOC_SUBDEV_G/S_FMT: OK test Active VIDIOC_SUBDEV_G/S_SELECTION/CROP: OK (Not Supported) test VIDIOC_SUBDEV_G/S_FRAME_INTERVAL: OK Control ioctls: test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK test VIDIOC_QUERYCTRL: OK test VIDIOC_G/S_CTRL: OK test VIDIOC_G/S/TRY_EXT_CTRLS: OK fail: ../../../../../../../../../../v4l-utils/utils/v4l2-compliance/v4l2-test-controls.cpp(816): subscribe event for control 'User Controls' failed test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 10 Private Controls: 0 Format ioctls: test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported) test VIDIOC_G/S_PARM: OK (Not Supported) test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK (Not Supported) test VIDIOC_TRY_FMT: OK (Not Supported) test VIDIOC_S_FMT: OK (Not Supported) test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) test Cropping: OK (Not Supported) test Composing: OK (Not Supported) test Scaling: OK (Not Supported) Codec ioctls: test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) Buffer ioctls: test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported) test VIDIOC_EXPBUF: OK (Not Supported) Total: 267, Succeeded: 261, Failed: 6, Warnings: 0 Rui Miguel Silva (13): media: staging/imx: refactor imx media device probe media: staging/imx: rearrange group id to take in account IPU media: staging/imx7: add imx7 CSI subdev driver media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7 media: dt-bindings: add bindings for i.MX7 media driver ARM: dts: imx7s: add mipi phy power domain ARM: dts: imx7s: add multiplexer controls ARM: dts: imx7: Add video mux, csi and mipi_csi and connections ARM: dts: imx7s-warp: add ov2680 sensor node media: imx7.rst: add documentation for i.MX7 media driver media: staging/imx: add i.MX7 entries to TODO file media: video-mux: add bayer formats media: MAINTAINERS: add entry for Freescale i.MX7 media driver .../devicetree/bindings/media/imx7-csi.txt | 45 + .../bindings/media/imx7-mipi-csi2.txt | 90 ++ Documentation/media/v4l-drivers/imx7.rst | 157 ++ Documentation/media/v4l-drivers/index.rst | 1 + MAINTAINERS | 11 + arch/arm/boot/dts/imx7s-warp.dts | 95 ++ arch/arm/boot/dts/imx7s.dtsi | 44 +- drivers/media/platform/video-mux.c | 20 + drivers/staging/media/imx/Kconfig | 9 +- drivers/staging/media/imx/Makefile | 4 + drivers/staging/media/imx/TODO | 9 + drivers/staging/media/imx/imx-ic-common.c | 6 +- drivers/staging/media/imx/imx-ic-prp.c | 16 +- drivers/staging/media/imx/imx-media-csi.c | 6 +- .../staging/media/imx/imx-media-dev-common.c | 102 ++ drivers/staging/media/imx/imx-media-dev.c | 110 +- .../staging/media/imx/imx-media-internal-sd.c | 20 +- drivers/staging/media/imx/imx-media-of.c | 6 +- drivers/staging/media/imx/imx-media-utils.c | 12 +- drivers/staging/media/imx/imx-media.h | 38 +- drivers/staging/media/imx/imx7-media-csi.c | 1354 +++++++++++++++++ drivers/staging/media/imx/imx7-mipi-csis.c | 1135 ++++++++++++++ 22 files changed, 3166 insertions(+), 124 deletions(-) create mode 100644 Documentation/devicetree/bindings/media/imx7-csi.txt create mode 100644 Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt create mode 100644 Documentation/media/v4l-drivers/imx7.rst create mode 100644 drivers/staging/media/imx/imx-media-dev-common.c create mode 100644 drivers/staging/media/imx/imx7-media-csi.c create mode 100644 drivers/staging/media/imx/imx7-mipi-csis.c