diff mbox series

[v3,3/6] dt-bindings: ap806: document the thermal interrupt capabilities

Message ID 20181204190332.10351-4-miquel.raynal@bootlin.com (mailing list archive)
State Superseded, archived
Delegated to: Eduardo Valentin
Headers show
Series Add hw overheat IRQ support to Marvell thermal driver | expand

Commit Message

Miquel Raynal Dec. 4, 2018, 7:03 p.m. UTC
The thermal IP can produce interrupts on overheat situation.
Describe them.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 .../bindings/arm/marvell/ap806-system-controller.txt      | 8 ++++++++
 1 file changed, 8 insertions(+)

Comments

Rob Herring (Arm) Dec. 10, 2018, 11:03 p.m. UTC | #1
On Tue, Dec 04, 2018 at 08:03:29PM +0100, Miquel Raynal wrote:
> The thermal IP can produce interrupts on overheat situation.
> Describe them.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>  .../bindings/arm/marvell/ap806-system-controller.txt      | 8 ++++++++
>  1 file changed, 8 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
> index 3fd21bb7cb37..35e8dd2edfd2 100644
> --- a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
> +++ b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
> @@ -114,12 +114,18 @@ Documentation/devicetree/bindings/thermal/thermal.txt
>  The thermal IP can probe the temperature all around the processor. It
>  may feature several channels, each of them wired to one sensor.
>  
> +It is possible to setup an overheat interrupt by giving at least one
> +critical point to any subnode of the thermal-zone node.
> +
>  Required properties:
>  - compatible: must be one of:
>    * marvell,armada-ap806-thermal
>  - reg: register range associated with the thermal functions.
>  
>  Optional properties:
> +- interrupt-parent/interrupts: overheat interrupt handle. Should point to
> +  line 18 of the SEI irqchip.
> +  See interrupt-controller/interrupts.txt

Don't document interrupt-parent as it is implied and may be in a parent 
node.

>  - #thermal-sensor-cells: shall be <1> when thermal-zones subnodes refer
>    to this IP and represents the channel ID. There is one sensor per
>    channel. O refers to the thermal IP internal channel, while positive
> @@ -133,6 +139,8 @@ ap_syscon1: system-controller@6f8000 {
>  	ap_thermal: thermal-sensor@80 {
>  		compatible = "marvell,armada-ap806-thermal";
>  		reg = <0x80 0x10>;
> +		interrupt-parent = <&sei>;
> +		interrupts = <18>;
>  		#thermal-sensor-cells = <1>;
>  	};
>  };
> -- 
> 2.19.1
>
Miquel Raynal Dec. 12, 2018, 9:32 a.m. UTC | #2
Hi Rob,

Rob Herring <robh@kernel.org> wrote on Mon, 10 Dec 2018 17:03:54 -0600:

> On Tue, Dec 04, 2018 at 08:03:29PM +0100, Miquel Raynal wrote:
> > The thermal IP can produce interrupts on overheat situation.
> > Describe them.
> > 
> > Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> > ---
> >  .../bindings/arm/marvell/ap806-system-controller.txt      | 8 ++++++++
> >  1 file changed, 8 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
> > index 3fd21bb7cb37..35e8dd2edfd2 100644
> > --- a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
> > +++ b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
> > @@ -114,12 +114,18 @@ Documentation/devicetree/bindings/thermal/thermal.txt
> >  The thermal IP can probe the temperature all around the processor. It
> >  may feature several channels, each of them wired to one sensor.
> >  
> > +It is possible to setup an overheat interrupt by giving at least one
> > +critical point to any subnode of the thermal-zone node.
> > +
> >  Required properties:
> >  - compatible: must be one of:
> >    * marvell,armada-ap806-thermal
> >  - reg: register range associated with the thermal functions.
> >  
> >  Optional properties:
> > +- interrupt-parent/interrupts: overheat interrupt handle. Should point to
> > +  line 18 of the SEI irqchip.
> > +  See interrupt-controller/interrupts.txt  
> 
> Don't document interrupt-parent as it is implied and may be in a parent 
> node.

Sure, I will send a v4.

> 
> >  - #thermal-sensor-cells: shall be <1> when thermal-zones subnodes refer
> >    to this IP and represents the channel ID. There is one sensor per
> >    channel. O refers to the thermal IP internal channel, while positive
> > @@ -133,6 +139,8 @@ ap_syscon1: system-controller@6f8000 {
> >  	ap_thermal: thermal-sensor@80 {
> >  		compatible = "marvell,armada-ap806-thermal";
> >  		reg = <0x80 0x10>;
> > +		interrupt-parent = <&sei>;
> > +		interrupts = <18>;
> >  		#thermal-sensor-cells = <1>;
> >  	};
> >  };
> > -- 
> > 2.19.1
> >   


Thanks,
Miquèl
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
index 3fd21bb7cb37..35e8dd2edfd2 100644
--- a/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
+++ b/Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
@@ -114,12 +114,18 @@  Documentation/devicetree/bindings/thermal/thermal.txt
 The thermal IP can probe the temperature all around the processor. It
 may feature several channels, each of them wired to one sensor.
 
+It is possible to setup an overheat interrupt by giving at least one
+critical point to any subnode of the thermal-zone node.
+
 Required properties:
 - compatible: must be one of:
   * marvell,armada-ap806-thermal
 - reg: register range associated with the thermal functions.
 
 Optional properties:
+- interrupt-parent/interrupts: overheat interrupt handle. Should point to
+  line 18 of the SEI irqchip.
+  See interrupt-controller/interrupts.txt
 - #thermal-sensor-cells: shall be <1> when thermal-zones subnodes refer
   to this IP and represents the channel ID. There is one sensor per
   channel. O refers to the thermal IP internal channel, while positive
@@ -133,6 +139,8 @@  ap_syscon1: system-controller@6f8000 {
 	ap_thermal: thermal-sensor@80 {
 		compatible = "marvell,armada-ap806-thermal";
 		reg = <0x80 0x10>;
+		interrupt-parent = <&sei>;
+		interrupts = <18>;
 		#thermal-sensor-cells = <1>;
 	};
 };