Message ID | 1539337244-9505-5-git-send-email-govinds@codeaurora.org (mailing list archive) |
---|---|
State | Not Applicable, archived |
Delegated to: | Andy Gross |
Headers | show |
Series | Add non PAS wcss Q6 support for QCS404 | expand |
Quoting Govind Singh (2018-10-12 02:40:42) > Add support for the WCSS QDSP clock control used on qcs404 > based devices. This would allow wcss remoteproc driver to > control the required WCSS QDSP clock/reset controls to > bring the subsystem out of reset and shutdown the WCSS QDSP. > > Signed-off-by: Govind Singh <govinds@codeaurora.org> > --- This needs to be sent to the clk mailing list and maintainers. > diff --git a/drivers/clk/qcom/wcsscc-qcs404.c b/drivers/clk/qcom/wcsscc-qcs404.c > new file mode 100644 > index 0000000..9a0c864 > --- /dev/null > +++ b/drivers/clk/qcom/wcsscc-qcs404.c > @@ -0,0 +1,290 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (c) 2018, The Linux Foundation. All rights reserved. > + */ > + > +#include <linux/bitops.h> > +#include <linux/err.h> > +#include <linux/platform_device.h> > +#include <linux/module.h> > +#include <linux/of_address.h> > +#include <linux/clk.h> > +#include <linux/clk-provider.h> > +#include <linux/regmap.h> > +#include <linux/regulator/consumer.h> > + > +#include <dt-bindings/clock/qcom,wcss-qcs404.h> > +#include <linux/reset-controller.h> > + > +#include "clk-regmap.h" > +#include "clk-branch.h" > +#include "common.h" > +#include "reset.h" > + > +/* Q6SSTOP clocks */ > +static struct clk_branch lcc_ahbfabric_cbc_clk = { > + .halt_reg = 0x1b004, > + .halt_check = BRANCH_VOTED, > + .clkr = { > + .enable_reg = 0x1b004, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "lcc_ahbfabric_cbc_clk", > + .ops = &clk_branch2_ops, > + .flags = CLK_IGNORE_UNUSED, > + }, > + }, > +}; > + > +static struct clk_branch lcc_q6ss_ahbs_cbc_clk = { > + .halt_reg = 0x22000, > + .halt_check = BRANCH_VOTED, > + .clkr = { > + .enable_reg = 0x22000, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "lcc_q6ss_ahbs_cbc_clk", > + .ops = &clk_branch2_ops, > + .flags = CLK_IGNORE_UNUSED, > + }, > + }, > +}; > + > +static struct clk_branch lcc_q6ss_tcm_slave_cbc_clk = { > + .halt_reg = 0x1c000, > + .halt_check = BRANCH_VOTED, > + .clkr = { > + .enable_reg = 0x1c000, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "lcc_q6ss_tcm_slave_cbc_clk", > + .ops = &clk_branch2_ops, > + .flags = CLK_IGNORE_UNUSED, > + }, > + }, > +}; > + > +static struct clk_branch lcc_q6ss_ahbm_cbc_clk = { > + .halt_reg = 0x22004, > + .halt_check = BRANCH_VOTED, > + .clkr = { > + .enable_reg = 0x22004, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "lcc_q6ss_ahbm_cbc_clk", > + .ops = &clk_branch2_ops, > + .flags = CLK_IGNORE_UNUSED, > + }, > + }, > +}; > + > +static struct clk_branch lcc_q6ss_axim_cbc_clk = { > + .halt_reg = 0x1c004, > + .halt_check = BRANCH_VOTED, > + .clkr = { > + .enable_reg = 0x1c004, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "lcc_q6ss_axim_cbc_clk", > + .ops = &clk_branch2_ops, > + .flags = CLK_IGNORE_UNUSED, > + }, > + }, > +}; > + > +static struct clk_branch lcc_q6ss_bcr_sleep_clk = { > + .halt_reg = 0x6004, > + .halt_check = BRANCH_VOTED, > + .clkr = { > + .enable_reg = 0x6004, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "lcc_q6ss_bcr_sleep_clk", > + .ops = &clk_branch2_ops, > + .flags = CLK_IGNORE_UNUSED, > + }, > + }, > +}; > + > +/* TCSR clock */ > +static struct clk_branch wcss_lcc_csr_cbcr_clk = { > + .halt_reg = 0x8008, > + .halt_check = BRANCH_VOTED, > + .clkr = { > + .enable_reg = 0x8008, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "wcss_lcc_csr_cbcr_clk", > + .ops = &clk_branch2_ops, > + .flags = CLK_IGNORE_UNUSED, > + }, > + }, > +}; > + > +/* Q6SSTOP_QDSP6SS clock */ > +static struct clk_branch q6ss_xo_clk = { > + .halt_reg = 0x38, > + .halt_check = BRANCH_HALT_SKIP, Why? > + .clkr = { > + .enable_reg = 0x38, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "q6ss_xo_clk", > + .ops = &clk_branch2_ops, > + .flags = CLK_IGNORE_UNUSED, > + }, > + }, > +}; > + > +static struct clk_branch q6ss_slp_clk = { > + .halt_reg = 0x3c, > + .halt_check = BRANCH_HALT_SKIP, Ditto. Please add a comment. > + .clkr = { > + .enable_reg = 0x3c, > + .enable_mask = BIT(0), > + .hw.init = &(struct clk_init_data){ > + .name = "q6ss_slp_clk", > + .ops = &clk_branch2_ops, > + .flags = CLK_IGNORE_UNUSED, > + }, > + }, > +}; > + > +static struct clk_branch q6sstop_q6ss_gfmux_clk_src = { > + .halt_reg = 0x20, > + .halt_check = BRANCH_HALT_SKIP, > + .clkr = { > + .enable_reg = 0x20, > + .enable_mask = (BIT(1) | BIT(3) | BIT(8)), Drop useless parenthesis please. And this is actually three clks in one? > + .hw.init = &(struct clk_init_data){ > + .name = "q6sstop_q6ss_gfmux_clk_src", > + .ops = &clk_branch2_ops, > + .flags = CLK_IGNORE_UNUSED, Why? Please explain with comment, etc. > + }, > + }, > +}; > + > +static struct regmap_config wcss_regmap_config = { > + .reg_bits = 32, > + .reg_stride = 4, > + .val_bits = 32, > + .fast_io = true, max register? Or that gets set later on somewhere? > +}; > + > +static struct clk_regmap *wcss_q6sstop_qcs405_clocks[] = { > + [WCSS_AHBFABRIC_CBCR_CLK] = &lcc_ahbfabric_cbc_clk.clkr, > + [WCSS_AHBS_CBCR_CLK] = &lcc_q6ss_ahbs_cbc_clk.clkr, > + [WCSS_TCM_CBCR_CLK] = &lcc_q6ss_tcm_slave_cbc_clk.clkr, > + [WCSS_AHBM_CBCR_CLK] = &lcc_q6ss_ahbm_cbc_clk.clkr, > + [WCSS_AXIM_CBCR_CLK] = &lcc_q6ss_axim_cbc_clk.clkr, > + [WCSS_BCR_CBCR_CLK] = &lcc_q6ss_bcr_sleep_clk.clkr, > +}; > + > +static const struct qcom_reset_map qdsp6ss_qcs405_resets[] = { > + [Q6SSTOP_QDSP6SS_RESET] = {0x14, 0}, > + [Q6SSTOP_QDSP6SS_CORE_RESET] = {0x14, 1}, > + [Q6SSTOP_QDSP6SS_BUS_RESET] = {0x14, 2}, > +}; > + > +static const struct qcom_reset_map q6sstop_qcs405_resets[] = { > + [Q6SSTOP_BCR_RESET] = {0x6000}, > +}; > + > +static const struct qcom_cc_desc wcss_q6sstop_qcs405_desc = { > + .config = &wcss_regmap_config, > + .clks = wcss_q6sstop_qcs405_clocks, > + .num_clks = ARRAY_SIZE(wcss_q6sstop_qcs405_clocks), > + .resets = q6sstop_qcs405_resets, > + .num_resets = ARRAY_SIZE(q6sstop_qcs405_resets), > +}; > + > +static struct clk_regmap *wcnss_tcsr_qcs405_clocks[] = { > + [WCSS_LCC_CBCR_CLK] = &wcss_lcc_csr_cbcr_clk.clkr, > +}; > + > +static const struct qcom_cc_desc wcnss_tcsr_qcs405_desc = { > + .config = &wcss_regmap_config, > + .clks = wcnss_tcsr_qcs405_clocks, > + .num_clks = ARRAY_SIZE(wcnss_tcsr_qcs405_clocks), > +}; > + > +static struct clk_regmap *wcnss_qdsp6ss_qcs405_clocks[] = { > + [WCSS_QDSP6SS_XO_CBCR_CLK] = &q6ss_xo_clk.clkr, > + [WCSS_QDSP6SS_SLEEP_CBCR_CLK] = &q6ss_slp_clk.clkr, > + [WCSS_QDSP6SS_GFMMUX_CLK] = &q6sstop_q6ss_gfmux_clk_src.clkr, > +}; > + > +static const struct qcom_cc_desc wcnss_qdsp6ss_qcs405_desc = { > + .config = &wcss_regmap_config, > + .clks = wcnss_qdsp6ss_qcs405_clocks, > + .num_clks = ARRAY_SIZE(wcnss_qdsp6ss_qcs405_clocks), > + .resets = qdsp6ss_qcs405_resets, > + .num_resets = ARRAY_SIZE(qdsp6ss_qcs405_resets), > +}; > + > +static int wcss_clocks_qcs405_probe(struct platform_device *pdev, int index, > + const struct qcom_cc_desc *desc) > +{ > + struct regmap *regmap; > + struct resource *res; > + void __iomem *base; > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, index); > + base = devm_ioremap_resource(&pdev->dev, res); > + if (IS_ERR(base)) > + return -ENOMEM; > + > + regmap = devm_regmap_init_mmio(&pdev->dev, base, desc->config); > + if (IS_ERR(regmap)) > + return PTR_ERR(regmap); > + > + return qcom_cc_really_probe(pdev, desc, regmap); > +} > + > +/* WCSS CC clock controller */ Please drop the obvious comment! > +static const struct of_device_id wcss_cc_qcs405_match_table[] = { > + { .compatible = "qcom,qcs405-wcsscc" }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, wcss_cc_qcs405_match_table); > + > +static int wcss_cc_qcs405_probe(struct platform_device *pdev) > +{ > + const struct qcom_cc_desc *desc; > + int ret; > + > + wcss_regmap_config.name = "wcss_q6sstop"; > + desc = &wcss_q6sstop_qcs405_desc; > + > + ret = wcss_clocks_qcs405_probe(pdev, 0, desc); > + if (ret) > + return ret; > + > + wcss_regmap_config.name = "wcnss_tcsr"; > + desc = &wcnss_tcsr_qcs405_desc; > + > + ret = wcss_clocks_qcs405_probe(pdev, 1, desc); > + if (ret) > + return ret; > + > + wcss_regmap_config.name = "wcss_qdsp6ss"; > + desc = &wcnss_qdsp6ss_qcs405_desc; > + > + return wcss_clocks_qcs405_probe(pdev, 2, desc); > +} And this is the second clk driver in qcom land to do this, so we need to add this to style of clk driver to clk/qcom/common.c
Thanks Stephen for the review. On 2018-10-16 06:30, Stephen Boyd wrote: > Quoting Govind Singh (2018-10-12 02:40:42) >> Add support for the WCSS QDSP clock control used on qcs404 >> based devices. This would allow wcss remoteproc driver to >> control the required WCSS QDSP clock/reset controls to >> bring the subsystem out of reset and shutdown the WCSS QDSP. >> >> Signed-off-by: Govind Singh <govinds@codeaurora.org> >> --- > > This needs to be sent to the clk mailing list and maintainers. > sure. >> diff --git a/drivers/clk/qcom/wcsscc-qcs404.c >> b/drivers/clk/qcom/wcsscc-qcs404.c >> new file mode 100644 >> index 0000000..9a0c864 >> --- /dev/null >> +++ b/drivers/clk/qcom/wcsscc-qcs404.c >> @@ -0,0 +1,290 @@ >> +// SPDX-License-Identifier: GPL-2.0 >> +/* >> + * Copyright (c) 2018, The Linux Foundation. All rights reserved. >> + */ >> + >> +#include <linux/bitops.h> >> +#include <linux/err.h> >> +#include <linux/platform_device.h> >> +#include <linux/module.h> >> +#include <linux/of_address.h> >> +#include <linux/clk.h> >> +#include <linux/clk-provider.h> >> +#include <linux/regmap.h> >> +#include <linux/regulator/consumer.h> >> + >> +#include <dt-bindings/clock/qcom,wcss-qcs404.h> >> +#include <linux/reset-controller.h> >> + >> +#include "clk-regmap.h" >> +#include "clk-branch.h" >> +#include "common.h" >> +#include "reset.h" >> + >> +/* Q6SSTOP clocks */ >> +static struct clk_branch lcc_ahbfabric_cbc_clk = { >> + .halt_reg = 0x1b004, >> + .halt_check = BRANCH_VOTED, >> + .clkr = { >> + .enable_reg = 0x1b004, >> + .enable_mask = BIT(0), >> + .hw.init = &(struct clk_init_data){ >> + .name = "lcc_ahbfabric_cbc_clk", >> + .ops = &clk_branch2_ops, >> + .flags = CLK_IGNORE_UNUSED, >> + }, >> + }, >> +}; >> + >> +static struct clk_branch lcc_q6ss_ahbs_cbc_clk = { >> + .halt_reg = 0x22000, >> + .halt_check = BRANCH_VOTED, >> + .clkr = { >> + .enable_reg = 0x22000, >> + .enable_mask = BIT(0), >> + .hw.init = &(struct clk_init_data){ >> + .name = "lcc_q6ss_ahbs_cbc_clk", >> + .ops = &clk_branch2_ops, >> + .flags = CLK_IGNORE_UNUSED, >> + }, >> + }, >> +}; >> + >> +static struct clk_branch lcc_q6ss_tcm_slave_cbc_clk = { >> + .halt_reg = 0x1c000, >> + .halt_check = BRANCH_VOTED, >> + .clkr = { >> + .enable_reg = 0x1c000, >> + .enable_mask = BIT(0), >> + .hw.init = &(struct clk_init_data){ >> + .name = "lcc_q6ss_tcm_slave_cbc_clk", >> + .ops = &clk_branch2_ops, >> + .flags = CLK_IGNORE_UNUSED, >> + }, >> + }, >> +}; >> + >> +static struct clk_branch lcc_q6ss_ahbm_cbc_clk = { >> + .halt_reg = 0x22004, >> + .halt_check = BRANCH_VOTED, >> + .clkr = { >> + .enable_reg = 0x22004, >> + .enable_mask = BIT(0), >> + .hw.init = &(struct clk_init_data){ >> + .name = "lcc_q6ss_ahbm_cbc_clk", >> + .ops = &clk_branch2_ops, >> + .flags = CLK_IGNORE_UNUSED, >> + }, >> + }, >> +}; >> + >> +static struct clk_branch lcc_q6ss_axim_cbc_clk = { >> + .halt_reg = 0x1c004, >> + .halt_check = BRANCH_VOTED, >> + .clkr = { >> + .enable_reg = 0x1c004, >> + .enable_mask = BIT(0), >> + .hw.init = &(struct clk_init_data){ >> + .name = "lcc_q6ss_axim_cbc_clk", >> + .ops = &clk_branch2_ops, >> + .flags = CLK_IGNORE_UNUSED, >> + }, >> + }, >> +}; >> + >> +static struct clk_branch lcc_q6ss_bcr_sleep_clk = { >> + .halt_reg = 0x6004, >> + .halt_check = BRANCH_VOTED, >> + .clkr = { >> + .enable_reg = 0x6004, >> + .enable_mask = BIT(0), >> + .hw.init = &(struct clk_init_data){ >> + .name = "lcc_q6ss_bcr_sleep_clk", >> + .ops = &clk_branch2_ops, >> + .flags = CLK_IGNORE_UNUSED, >> + }, >> + }, >> +}; >> + >> +/* TCSR clock */ >> +static struct clk_branch wcss_lcc_csr_cbcr_clk = { >> + .halt_reg = 0x8008, >> + .halt_check = BRANCH_VOTED, >> + .clkr = { >> + .enable_reg = 0x8008, >> + .enable_mask = BIT(0), >> + .hw.init = &(struct clk_init_data){ >> + .name = "wcss_lcc_csr_cbcr_clk", >> + .ops = &clk_branch2_ops, >> + .flags = CLK_IGNORE_UNUSED, >> + }, >> + }, >> +}; >> + >> +/* Q6SSTOP_QDSP6SS clock */ >> +static struct clk_branch q6ss_xo_clk = { >> + .halt_reg = 0x38, >> + .halt_check = BRANCH_HALT_SKIP, > > Why? > CLK_OFF would not toggle until WCSS is out of reset. >> +static struct clk_branch q6sstop_q6ss_gfmux_clk_src = { >> + .halt_reg = 0x20, >> + .halt_check = BRANCH_HALT_SKIP, >> + .clkr = { >> + .enable_reg = 0x20, >> + .enable_mask = (BIT(1) | BIT(3) | BIT(8)), > > Drop useless parenthesis please. And this is actually three clks in > one? > Addressed in v3. >> + .hw.init = &(struct clk_init_data){ >> + .name = "q6sstop_q6ss_gfmux_clk_src", >> + .ops = &clk_branch2_ops, >> + .flags = CLK_IGNORE_UNUSED, > > Why? Please explain with comment, etc. > Added comment in the v3 version for CLK_IGNORE_UNUSED flag. >> + }, >> + }, >> +}; >> + >> +static struct regmap_config wcss_regmap_config = { >> + .reg_bits = 32, >> + .reg_stride = 4, >> + .val_bits = 32, >> + .fast_io = true, > > max register? Or that gets set later on somewhere? > Addressed in v3. >> +}; >> + >> +static struct clk_regmap *wcss_q6sstop_qcs405_clocks[] = { >> + [WCSS_AHBFABRIC_CBCR_CLK] = &lcc_ahbfabric_cbc_clk.clkr, >> + [WCSS_AHBS_CBCR_CLK] = &lcc_q6ss_ahbs_cbc_clk.clkr, >> + [WCSS_TCM_CBCR_CLK] = &lcc_q6ss_tcm_slave_cbc_clk.clkr, >> + [WCSS_AHBM_CBCR_CLK] = &lcc_q6ss_ahbm_cbc_clk.clkr, >> + [WCSS_AXIM_CBCR_CLK] = &lcc_q6ss_axim_cbc_clk.clkr, >> + [WCSS_BCR_CBCR_CLK] = &lcc_q6ss_bcr_sleep_clk.clkr, >> +}; >> + >> +static const struct qcom_reset_map qdsp6ss_qcs405_resets[] = { >> + [Q6SSTOP_QDSP6SS_RESET] = {0x14, 0}, >> + [Q6SSTOP_QDSP6SS_CORE_RESET] = {0x14, 1}, >> + [Q6SSTOP_QDSP6SS_BUS_RESET] = {0x14, 2}, >> +}; >> + >> +static const struct qcom_reset_map q6sstop_qcs405_resets[] = { >> + [Q6SSTOP_BCR_RESET] = {0x6000}, >> +}; >> + >> +static const struct qcom_cc_desc wcss_q6sstop_qcs405_desc = { >> + .config = &wcss_regmap_config, >> + .clks = wcss_q6sstop_qcs405_clocks, >> + .num_clks = ARRAY_SIZE(wcss_q6sstop_qcs405_clocks), >> + .resets = q6sstop_qcs405_resets, >> + .num_resets = ARRAY_SIZE(q6sstop_qcs405_resets), >> +}; >> + >> +static struct clk_regmap *wcnss_tcsr_qcs405_clocks[] = { >> + [WCSS_LCC_CBCR_CLK] = &wcss_lcc_csr_cbcr_clk.clkr, >> +}; >> + >> +static const struct qcom_cc_desc wcnss_tcsr_qcs405_desc = { >> + .config = &wcss_regmap_config, >> + .clks = wcnss_tcsr_qcs405_clocks, >> + .num_clks = ARRAY_SIZE(wcnss_tcsr_qcs405_clocks), >> +}; >> + >> +static struct clk_regmap *wcnss_qdsp6ss_qcs405_clocks[] = { >> + [WCSS_QDSP6SS_XO_CBCR_CLK] = &q6ss_xo_clk.clkr, >> + [WCSS_QDSP6SS_SLEEP_CBCR_CLK] = &q6ss_slp_clk.clkr, >> + [WCSS_QDSP6SS_GFMMUX_CLK] = &q6sstop_q6ss_gfmux_clk_src.clkr, >> +}; >> + >> +static const struct qcom_cc_desc wcnss_qdsp6ss_qcs405_desc = { >> + .config = &wcss_regmap_config, >> + .clks = wcnss_qdsp6ss_qcs405_clocks, >> + .num_clks = ARRAY_SIZE(wcnss_qdsp6ss_qcs405_clocks), >> + .resets = qdsp6ss_qcs405_resets, >> + .num_resets = ARRAY_SIZE(qdsp6ss_qcs405_resets), >> +}; >> + >> +static int wcss_clocks_qcs405_probe(struct platform_device *pdev, int >> index, >> + const struct qcom_cc_desc *desc) >> +{ >> + struct regmap *regmap; >> + struct resource *res; >> + void __iomem *base; >> + >> + res = platform_get_resource(pdev, IORESOURCE_MEM, index); >> + base = devm_ioremap_resource(&pdev->dev, res); >> + if (IS_ERR(base)) >> + return -ENOMEM; >> + >> + regmap = devm_regmap_init_mmio(&pdev->dev, base, >> desc->config); >> + if (IS_ERR(regmap)) >> + return PTR_ERR(regmap); >> + >> + return qcom_cc_really_probe(pdev, desc, regmap); >> +} >> + >> +/* WCSS CC clock controller */ > > Please drop the obvious comment! > Addressed in v3. >> +static const struct of_device_id wcss_cc_qcs405_match_table[] = { >> + { .compatible = "qcom,qcs405-wcsscc" }, >> + { } >> +}; >> +MODULE_DEVICE_TABLE(of, wcss_cc_qcs405_match_table); >> + >> +static int wcss_cc_qcs405_probe(struct platform_device *pdev) >> +{ >> + const struct qcom_cc_desc *desc; >> + int ret; >> + >> + wcss_regmap_config.name = "wcss_q6sstop"; >> + desc = &wcss_q6sstop_qcs405_desc; >> + >> + ret = wcss_clocks_qcs405_probe(pdev, 0, desc); >> + if (ret) >> + return ret; >> + >> + wcss_regmap_config.name = "wcnss_tcsr"; >> + desc = &wcnss_tcsr_qcs405_desc; >> + >> + ret = wcss_clocks_qcs405_probe(pdev, 1, desc); >> + if (ret) >> + return ret; >> + >> + wcss_regmap_config.name = "wcss_qdsp6ss"; >> + desc = &wcnss_qdsp6ss_qcs405_desc; >> + >> + return wcss_clocks_qcs405_probe(pdev, 2, desc); >> +} > > And this is the second clk driver in qcom land to do this, so we need > to > add this to style of clk driver to clk/qcom/common.c Seems LPASS clk driver is still under review, can i address this comment as separate patch. BR, Govind
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig index 5cdcb37..9ffc003 100644 --- a/drivers/clk/qcom/Kconfig +++ b/drivers/clk/qcom/Kconfig @@ -253,6 +253,15 @@ config QCS_GCC_404 Say Y if you want to use peripheral devices such as UART, SPI, I2C, USB, SD/eMMC, PCIe, etc. +config QCS_WCSS_404 + tristate "QCS404 WCSS Clock Controller" + depends on COMMON_CLK_QCOM + select QCS_GCC_404 + help + Support for the WCSS clock controller on QCS404 devices. + Say Y if you want to use the WCSS branch clocks of the WCSS clock + controller to reset the WCSS subsystem. + config SDM_GCC_845 tristate "SDM845 Global Clock Controller" select QCOM_GDSC diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile index 0a4790e..d258d4f 100644 --- a/drivers/clk/qcom/Makefile +++ b/drivers/clk/qcom/Makefile @@ -44,6 +44,7 @@ obj-$(CONFIG_QCOM_CLK_RPMH) += clk-rpmh.o obj-$(CONFIG_QCOM_CLK_SMD_RPM) += clk-smd-rpm.o obj-$(CONFIG_SDM_DISPCC_845) += dispcc-sdm845.o obj-$(CONFIG_QCS_GCC_404) += gcc-qcs404.o +obj-$(CONFIG_QCS_WCSS_404) += wcsscc-qcs404.o obj-$(CONFIG_SDM_GCC_845) += gcc-sdm845.o obj-$(CONFIG_SDM_VIDEOCC_845) += videocc-sdm845.o obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o diff --git a/drivers/clk/qcom/wcsscc-qcs404.c b/drivers/clk/qcom/wcsscc-qcs404.c new file mode 100644 index 0000000..9a0c864 --- /dev/null +++ b/drivers/clk/qcom/wcsscc-qcs404.c @@ -0,0 +1,290 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2018, The Linux Foundation. All rights reserved. + */ + +#include <linux/bitops.h> +#include <linux/err.h> +#include <linux/platform_device.h> +#include <linux/module.h> +#include <linux/of_address.h> +#include <linux/clk.h> +#include <linux/clk-provider.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> + +#include <dt-bindings/clock/qcom,wcss-qcs404.h> +#include <linux/reset-controller.h> + +#include "clk-regmap.h" +#include "clk-branch.h" +#include "common.h" +#include "reset.h" + +/* Q6SSTOP clocks */ +static struct clk_branch lcc_ahbfabric_cbc_clk = { + .halt_reg = 0x1b004, + .halt_check = BRANCH_VOTED, + .clkr = { + .enable_reg = 0x1b004, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "lcc_ahbfabric_cbc_clk", + .ops = &clk_branch2_ops, + .flags = CLK_IGNORE_UNUSED, + }, + }, +}; + +static struct clk_branch lcc_q6ss_ahbs_cbc_clk = { + .halt_reg = 0x22000, + .halt_check = BRANCH_VOTED, + .clkr = { + .enable_reg = 0x22000, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "lcc_q6ss_ahbs_cbc_clk", + .ops = &clk_branch2_ops, + .flags = CLK_IGNORE_UNUSED, + }, + }, +}; + +static struct clk_branch lcc_q6ss_tcm_slave_cbc_clk = { + .halt_reg = 0x1c000, + .halt_check = BRANCH_VOTED, + .clkr = { + .enable_reg = 0x1c000, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "lcc_q6ss_tcm_slave_cbc_clk", + .ops = &clk_branch2_ops, + .flags = CLK_IGNORE_UNUSED, + }, + }, +}; + +static struct clk_branch lcc_q6ss_ahbm_cbc_clk = { + .halt_reg = 0x22004, + .halt_check = BRANCH_VOTED, + .clkr = { + .enable_reg = 0x22004, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "lcc_q6ss_ahbm_cbc_clk", + .ops = &clk_branch2_ops, + .flags = CLK_IGNORE_UNUSED, + }, + }, +}; + +static struct clk_branch lcc_q6ss_axim_cbc_clk = { + .halt_reg = 0x1c004, + .halt_check = BRANCH_VOTED, + .clkr = { + .enable_reg = 0x1c004, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "lcc_q6ss_axim_cbc_clk", + .ops = &clk_branch2_ops, + .flags = CLK_IGNORE_UNUSED, + }, + }, +}; + +static struct clk_branch lcc_q6ss_bcr_sleep_clk = { + .halt_reg = 0x6004, + .halt_check = BRANCH_VOTED, + .clkr = { + .enable_reg = 0x6004, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "lcc_q6ss_bcr_sleep_clk", + .ops = &clk_branch2_ops, + .flags = CLK_IGNORE_UNUSED, + }, + }, +}; + +/* TCSR clock */ +static struct clk_branch wcss_lcc_csr_cbcr_clk = { + .halt_reg = 0x8008, + .halt_check = BRANCH_VOTED, + .clkr = { + .enable_reg = 0x8008, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "wcss_lcc_csr_cbcr_clk", + .ops = &clk_branch2_ops, + .flags = CLK_IGNORE_UNUSED, + }, + }, +}; + +/* Q6SSTOP_QDSP6SS clock */ +static struct clk_branch q6ss_xo_clk = { + .halt_reg = 0x38, + .halt_check = BRANCH_HALT_SKIP, + .clkr = { + .enable_reg = 0x38, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "q6ss_xo_clk", + .ops = &clk_branch2_ops, + .flags = CLK_IGNORE_UNUSED, + }, + }, +}; + +static struct clk_branch q6ss_slp_clk = { + .halt_reg = 0x3c, + .halt_check = BRANCH_HALT_SKIP, + .clkr = { + .enable_reg = 0x3c, + .enable_mask = BIT(0), + .hw.init = &(struct clk_init_data){ + .name = "q6ss_slp_clk", + .ops = &clk_branch2_ops, + .flags = CLK_IGNORE_UNUSED, + }, + }, +}; + +static struct clk_branch q6sstop_q6ss_gfmux_clk_src = { + .halt_reg = 0x20, + .halt_check = BRANCH_HALT_SKIP, + .clkr = { + .enable_reg = 0x20, + .enable_mask = (BIT(1) | BIT(3) | BIT(8)), + .hw.init = &(struct clk_init_data){ + .name = "q6sstop_q6ss_gfmux_clk_src", + .ops = &clk_branch2_ops, + .flags = CLK_IGNORE_UNUSED, + }, + }, +}; + +static struct regmap_config wcss_regmap_config = { + .reg_bits = 32, + .reg_stride = 4, + .val_bits = 32, + .fast_io = true, +}; + +static struct clk_regmap *wcss_q6sstop_qcs405_clocks[] = { + [WCSS_AHBFABRIC_CBCR_CLK] = &lcc_ahbfabric_cbc_clk.clkr, + [WCSS_AHBS_CBCR_CLK] = &lcc_q6ss_ahbs_cbc_clk.clkr, + [WCSS_TCM_CBCR_CLK] = &lcc_q6ss_tcm_slave_cbc_clk.clkr, + [WCSS_AHBM_CBCR_CLK] = &lcc_q6ss_ahbm_cbc_clk.clkr, + [WCSS_AXIM_CBCR_CLK] = &lcc_q6ss_axim_cbc_clk.clkr, + [WCSS_BCR_CBCR_CLK] = &lcc_q6ss_bcr_sleep_clk.clkr, +}; + +static const struct qcom_reset_map qdsp6ss_qcs405_resets[] = { + [Q6SSTOP_QDSP6SS_RESET] = {0x14, 0}, + [Q6SSTOP_QDSP6SS_CORE_RESET] = {0x14, 1}, + [Q6SSTOP_QDSP6SS_BUS_RESET] = {0x14, 2}, +}; + +static const struct qcom_reset_map q6sstop_qcs405_resets[] = { + [Q6SSTOP_BCR_RESET] = {0x6000}, +}; + +static const struct qcom_cc_desc wcss_q6sstop_qcs405_desc = { + .config = &wcss_regmap_config, + .clks = wcss_q6sstop_qcs405_clocks, + .num_clks = ARRAY_SIZE(wcss_q6sstop_qcs405_clocks), + .resets = q6sstop_qcs405_resets, + .num_resets = ARRAY_SIZE(q6sstop_qcs405_resets), +}; + +static struct clk_regmap *wcnss_tcsr_qcs405_clocks[] = { + [WCSS_LCC_CBCR_CLK] = &wcss_lcc_csr_cbcr_clk.clkr, +}; + +static const struct qcom_cc_desc wcnss_tcsr_qcs405_desc = { + .config = &wcss_regmap_config, + .clks = wcnss_tcsr_qcs405_clocks, + .num_clks = ARRAY_SIZE(wcnss_tcsr_qcs405_clocks), +}; + +static struct clk_regmap *wcnss_qdsp6ss_qcs405_clocks[] = { + [WCSS_QDSP6SS_XO_CBCR_CLK] = &q6ss_xo_clk.clkr, + [WCSS_QDSP6SS_SLEEP_CBCR_CLK] = &q6ss_slp_clk.clkr, + [WCSS_QDSP6SS_GFMMUX_CLK] = &q6sstop_q6ss_gfmux_clk_src.clkr, +}; + +static const struct qcom_cc_desc wcnss_qdsp6ss_qcs405_desc = { + .config = &wcss_regmap_config, + .clks = wcnss_qdsp6ss_qcs405_clocks, + .num_clks = ARRAY_SIZE(wcnss_qdsp6ss_qcs405_clocks), + .resets = qdsp6ss_qcs405_resets, + .num_resets = ARRAY_SIZE(qdsp6ss_qcs405_resets), +}; + +static int wcss_clocks_qcs405_probe(struct platform_device *pdev, int index, + const struct qcom_cc_desc *desc) +{ + struct regmap *regmap; + struct resource *res; + void __iomem *base; + + res = platform_get_resource(pdev, IORESOURCE_MEM, index); + base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(base)) + return -ENOMEM; + + regmap = devm_regmap_init_mmio(&pdev->dev, base, desc->config); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + return qcom_cc_really_probe(pdev, desc, regmap); +} + +/* WCSS CC clock controller */ +static const struct of_device_id wcss_cc_qcs405_match_table[] = { + { .compatible = "qcom,qcs405-wcsscc" }, + { } +}; +MODULE_DEVICE_TABLE(of, wcss_cc_qcs405_match_table); + +static int wcss_cc_qcs405_probe(struct platform_device *pdev) +{ + const struct qcom_cc_desc *desc; + int ret; + + wcss_regmap_config.name = "wcss_q6sstop"; + desc = &wcss_q6sstop_qcs405_desc; + + ret = wcss_clocks_qcs405_probe(pdev, 0, desc); + if (ret) + return ret; + + wcss_regmap_config.name = "wcnss_tcsr"; + desc = &wcnss_tcsr_qcs405_desc; + + ret = wcss_clocks_qcs405_probe(pdev, 1, desc); + if (ret) + return ret; + + wcss_regmap_config.name = "wcss_qdsp6ss"; + desc = &wcnss_qdsp6ss_qcs405_desc; + + return wcss_clocks_qcs405_probe(pdev, 2, desc); +} + +static struct platform_driver wcss_cc_qcs405_driver = { + .probe = wcss_cc_qcs405_probe, + .driver = { + .name = "qcs405-wcsscc", + .of_match_table = wcss_cc_qcs405_match_table, + }, +}; + +static int __init wcss_cc_qcs405_init(void) +{ + return platform_driver_register(&wcss_cc_qcs405_driver); +} +subsys_initcall(wcss_cc_qcs405_init); + +MODULE_LICENSE("GPL v2");
Add support for the WCSS QDSP clock control used on qcs404 based devices. This would allow wcss remoteproc driver to control the required WCSS QDSP clock/reset controls to bring the subsystem out of reset and shutdown the WCSS QDSP. Signed-off-by: Govind Singh <govinds@codeaurora.org> --- drivers/clk/qcom/Kconfig | 9 ++ drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/wcsscc-qcs404.c | 290 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 300 insertions(+) create mode 100644 drivers/clk/qcom/wcsscc-qcs404.c