@@ -8,7 +8,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include <linux/slab.h>
@@ -79,14 +79,14 @@ static int init_display(struct fbtft_par *par)
static void reset(struct fbtft_par *par)
{
- if (par->gpio.reset == -1)
+ if (!par->gpio.reset)
return;
dev_dbg(par->info->device, "%s()\n", __func__);
- gpio_set_value(par->gpio.reset, 0);
+ gpiod_set_value(par->gpio.reset, 0);
udelay(20);
- gpio_set_value(par->gpio.reset, 1);
+ gpiod_set_value(par->gpio.reset, 1);
mdelay(120);
}
@@ -98,30 +98,30 @@ static int verify_gpios(struct fbtft_par *par)
dev_dbg(par->info->device,
"%s()\n", __func__);
- if (par->EPIN < 0) {
+ if (!par->EPIN) {
dev_err(par->info->device,
"Missing info about 'wr' (aka E) gpio. Aborting.\n");
return -EINVAL;
}
for (i = 0; i < 8; ++i) {
- if (par->gpio.db[i] < 0) {
+ if (!par->gpio.db[i]) {
dev_err(par->info->device,
"Missing info about 'db[%i]' gpio. Aborting.\n",
i);
return -EINVAL;
}
}
- if (par->CS0 < 0) {
+ if (!par->CS0) {
dev_err(par->info->device,
"Missing info about 'cs0' gpio. Aborting.\n");
return -EINVAL;
}
- if (par->CS1 < 0) {
+ if (!par->CS1) {
dev_err(par->info->device,
"Missing info about 'cs1' gpio. Aborting.\n");
return -EINVAL;
}
- if (par->RW < 0) {
+ if (!par->RW) {
dev_err(par->info->device,
"Missing info about 'rw' gpio. Aborting.\n");
return -EINVAL;
@@ -139,22 +139,22 @@ request_gpios_match(struct fbtft_par *par, const struct fbtft_gpio *gpio)
if (strcasecmp(gpio->name, "wr") == 0) {
/* left ks0108 E pin */
par->EPIN = gpio->gpio;
- return GPIOF_OUT_INIT_LOW;
+ return GPIOD_OUT_LOW;
} else if (strcasecmp(gpio->name, "cs0") == 0) {
/* left ks0108 controller pin */
par->CS0 = gpio->gpio;
- return GPIOF_OUT_INIT_HIGH;
+ return GPIOD_OUT_HIGH;
} else if (strcasecmp(gpio->name, "cs1") == 0) {
/* right ks0108 controller pin */
par->CS1 = gpio->gpio;
- return GPIOF_OUT_INIT_HIGH;
+ return GPIOD_OUT_HIGH;
}
/* if write (rw = 0) e(1->0) perform write */
/* if read (rw = 1) e(0->1) set data on D0-7*/
else if (strcasecmp(gpio->name, "rw") == 0) {
par->RW = gpio->gpio;
- return GPIOF_OUT_INIT_LOW;
+ return GPIOD_OUT_LOW;
}
return FBTFT_GPIO_NO_MATCH;
@@ -194,15 +194,15 @@ static void write_reg8_bus8(struct fbtft_par *par, int len, ...)
/* select chip */
if (*buf) {
/* cs1 */
- gpio_set_value(par->CS0, 1);
- gpio_set_value(par->CS1, 0);
+ gpiod_set_value(par->CS0, 1);
+ gpiod_set_value(par->CS1, 0);
} else {
/* cs0 */
- gpio_set_value(par->CS0, 0);
- gpio_set_value(par->CS1, 1);
+ gpiod_set_value(par->CS0, 0);
+ gpiod_set_value(par->CS1, 1);
}
- gpio_set_value(par->RS, 0); /* RS->0 (command mode) */
+ gpiod_set_value(par->RS, 0); /* RS->0 (command mode) */
len--;
if (len) {
@@ -364,7 +364,7 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
write_reg(par, 0x00, (0x17 << 3) | (u8)y);
/* write bitmap */
- gpio_set_value(par->RS, 1); /* RS->1 (data mode) */
+ gpiod_set_value(par->RS, 1); /* RS->1 (data mode) */
ret = par->fbtftops.write(par, buf, len);
if (ret < 0)
dev_err(par->info->device,
@@ -387,7 +387,7 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
write_reg(par, 0x01, (0x17 << 3) | (u8)y);
/* write bitmap */
- gpio_set_value(par->RS, 1); /* RS->1 (data mode) */
+ gpiod_set_value(par->RS, 1); /* RS->1 (data mode) */
par->fbtftops.write(par, buf, len);
if (ret < 0)
dev_err(par->info->device,
@@ -397,8 +397,8 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
}
kfree(convert_buf);
- gpio_set_value(par->CS0, 1);
- gpio_set_value(par->CS1, 1);
+ gpiod_set_value(par->CS0, 1);
+ gpiod_set_value(par->CS1, 1);
return ret;
}
@@ -408,7 +408,7 @@ static int write(struct fbtft_par *par, void *buf, size_t len)
fbtft_par_dbg_hex(DEBUG_WRITE, par, par->info->device, u8, buf, len,
"%s(len=%d): ", __func__, len);
- gpio_set_value(par->RW, 0); /* set write mode */
+ gpiod_set_value(par->RW, 0); /* set write mode */
while (len--) {
u8 i, data;
@@ -417,12 +417,12 @@ static int write(struct fbtft_par *par, void *buf, size_t len)
/* set data bus */
for (i = 0; i < 8; ++i)
- gpio_set_value(par->gpio.db[i], data & (1 << i));
+ gpiod_set_value(par->gpio.db[i], data & (1 << i));
/* set E */
- gpio_set_value(par->EPIN, 1);
+ gpiod_set_value(par->EPIN, 1);
udelay(5);
/* unset E - write */
- gpio_set_value(par->EPIN, 0);
+ gpiod_set_value(par->EPIN, 0);
udelay(1);
}
@@ -12,7 +12,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include "fbtft.h"
@@ -24,8 +24,8 @@
static int init_display(struct fbtft_par *par)
{
- if (par->gpio.cs != -1)
- gpio_set_value(par->gpio.cs, 0); /* Activate chip */
+ if (!par->gpio.cs)
+ gpiod_set_value(par->gpio.cs, 0); /* Activate chip */
par->fbtftops.reset(par);
@@ -11,7 +11,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include <video/mipi_display.h>
@@ -77,8 +77,8 @@ static int init_display(struct fbtft_par *par)
{
par->fbtftops.reset(par);
- if (par->gpio.cs != -1)
- gpio_set_value(par->gpio.cs, 0); /* Activate chip */
+ if (!par->gpio.cs)
+ gpiod_set_value(par->gpio.cs, 0); /* Activate chip */
write_reg(par, MIPI_DCS_SOFT_RESET); /* software reset */
mdelay(500);
@@ -8,7 +8,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include <linux/delay.h>
@@ -10,7 +10,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include "fbtft.h"
@@ -85,8 +85,8 @@ static int init_display(struct fbtft_par *par)
{
par->fbtftops.reset(par);
- if (par->gpio.cs != -1)
- gpio_set_value(par->gpio.cs, 0); /* Activate chip */
+ if (!par->gpio.cs)
+ gpiod_set_value(par->gpio.cs, 0); /* Activate chip */
bt &= 0x07;
vc &= 0x07;
@@ -8,7 +8,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include <video/mipi_display.h>
@@ -11,7 +11,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include <linux/delay.h>
@@ -119,7 +119,7 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
}
/* Write data */
- gpio_set_value(par->gpio.dc, 1);
+ gpiod_set_value(par->gpio.dc, 1);
ret = par->fbtftops.write(par, par->txbuf.buf, 6 * 84);
if (ret < 0)
dev_err(par->info->device, "write failed and returned: %d\n",
@@ -9,7 +9,7 @@
#include <linux/init.h>
#include <linux/delay.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include "fbtft.h"
#define DRVNAME "fb_ra8875"
@@ -39,7 +39,7 @@ static int write_spi(struct fbtft_par *par, void *buf, size_t len)
static int init_display(struct fbtft_par *par)
{
- gpio_set_value(par->gpio.dc, 1);
+ gpiod_set_value(par->gpio.dc, 1);
fbtft_par_dbg(DEBUG_INIT_DISPLAY, par,
"%s()\n", __func__);
@@ -12,7 +12,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include "fbtft.h"
@@ -29,8 +29,8 @@ static int init_display(struct fbtft_par *par)
{
par->fbtftops.reset(par);
- if (par->gpio.cs != -1)
- gpio_set_value(par->gpio.cs, 0); /* Activate chip */
+ if (!par->gpio.cs)
+ gpiod_set_value(par->gpio.cs, 0); /* Activate chip */
/* Initialization sequence from Lib_UTFT */
@@ -9,7 +9,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include "fbtft.h"
@@ -10,7 +10,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include "fbtft.h"
@@ -28,8 +28,8 @@ static int init_display(struct fbtft_par *par)
{
par->fbtftops.reset(par);
- if (par->gpio.cs != -1)
- gpio_set_value(par->gpio.cs, 0); /* Activate chip */
+ if (!par->gpio.cs)
+ gpiod_set_value(par->gpio.cs, 0); /* Activate chip */
write_reg(par, 0x00, 0x0001);
write_reg(par, 0x03, 0xA8A4);
@@ -8,7 +8,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include "fbtft.h"
@@ -168,7 +168,7 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
}
/* Write data */
- gpio_set_value(par->gpio.dc, 1);
+ gpiod_set_value(par->gpio.dc, 1);
ret = par->fbtftops.write(par, par->txbuf.buf,
par->info->var.xres * par->info->var.yres /
8);
@@ -8,7 +8,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include "fbtft.h"
@@ -190,7 +190,7 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
}
/* Write data */
- gpio_set_value(par->gpio.dc, 1);
+ gpiod_set_value(par->gpio.dc, 1);
ret = par->fbtftops.write(par, par->txbuf.buf, xres * yres / 8);
if (ret < 0)
dev_err(par->info->device, "write failed and returned: %d\n",
@@ -6,7 +6,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include "fbtft.h"
@@ -35,7 +35,7 @@ static int init_display(struct fbtft_par *par)
{
par->fbtftops.reset(par);
- gpio_set_value(par->gpio.cs, 0);
+ gpiod_set_value(par->gpio.cs, 0);
write_reg(par, 0xb3);
write_reg(par, 0xf0);
@@ -155,7 +155,7 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
}
}
- gpio_set_value(par->gpio.dc, 1);
+ gpiod_set_value(par->gpio.dc, 1);
/* Write data */
ret = par->fbtftops.write(par, par->txbuf.buf,
@@ -2,7 +2,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include <linux/delay.h>
@@ -80,8 +80,8 @@ static void write_reg8_bus8(struct fbtft_par *par, int len, ...)
va_start(args, len);
*buf = (u8)va_arg(args, unsigned int);
- if (par->gpio.dc != -1)
- gpio_set_value(par->gpio.dc, 0);
+ if (!par->gpio.dc)
+ gpiod_set_value(par->gpio.dc, 0);
ret = par->fbtftops.write(par, par->buf, sizeof(u8));
if (ret < 0) {
va_end(args);
@@ -103,8 +103,8 @@ static void write_reg8_bus8(struct fbtft_par *par, int len, ...)
return;
}
}
- if (par->gpio.dc != -1)
- gpio_set_value(par->gpio.dc, 1);
+ if (!par->gpio.dc)
+ gpiod_set_value(par->gpio.dc, 1);
va_end(args);
}
@@ -2,7 +2,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include <linux/delay.h>
@@ -12,7 +12,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include <linux/delay.h>
@@ -94,7 +94,7 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
/* The display is 102x68 but the LCD is 84x48.
* Set the write pointer at the start of each row.
*/
- gpio_set_value(par->gpio.dc, 0);
+ gpiod_set_value(par->gpio.dc, 0);
write_reg(par, 0x80 | 0);
write_reg(par, 0x40 | y);
@@ -109,7 +109,7 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
*buf++ = ch;
}
/* Write the row */
- gpio_set_value(par->gpio.dc, 1);
+ gpiod_set_value(par->gpio.dc, 1);
ret = par->fbtftops.write(par, par->txbuf.buf, WIDTH);
if (ret < 0) {
dev_err(par->info->device,
@@ -10,7 +10,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include <linux/delay.h>
@@ -251,7 +251,7 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
}
break;
}
- gpio_set_value(par->gpio.dc, 1);
+ gpiod_set_value(par->gpio.dc, 1);
/* Write data */
ret = par->fbtftops.write(par, par->txbuf.buf, len / 2);
@@ -11,7 +11,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include <linux/delay.h>
@@ -136,9 +136,9 @@ static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
write_reg(par, LCD_PAGE_ADDRESS | (u8)y);
write_reg(par, 0x00);
write_reg(par, LCD_COL_ADDRESS);
- gpio_set_value(par->gpio.dc, 1);
+ gpiod_set_value(par->gpio.dc, 1);
ret = par->fbtftops.write(par, par->txbuf.buf, WIDTH);
- gpio_set_value(par->gpio.dc, 0);
+ gpiod_set_value(par->gpio.dc, 0);
}
if (ret < 0)
@@ -12,7 +12,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include "fbtft.h"
@@ -26,8 +26,8 @@ static int init_display(struct fbtft_par *par)
{
par->fbtftops.reset(par);
- if (par->gpio.cs != -1)
- gpio_set_value(par->gpio.cs, 0); /* Activate chip */
+ if (!par->gpio.cs)
+ gpiod_set_value(par->gpio.cs, 0); /* Activate chip */
/* Initialization sequence from Lib_UTFT */
@@ -8,7 +8,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include "fbtft.h"
@@ -213,7 +213,7 @@ static int set_var(struct fbtft_par *par)
static int verify_gpios(struct fbtft_par *par)
{
- if (par->gpio.reset < 0) {
+ if (!par->gpio.reset) {
dev_err(par->info->device, "Missing 'reset' gpio. Aborting.\n");
return -EINVAL;
}
@@ -1,7 +1,7 @@
// SPDX-License-Identifier: GPL-2.0
#include <linux/export.h>
#include <linux/errno.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include "fbtft.h"
@@ -135,8 +135,8 @@ int fbtft_write_vmem16_bus8(struct fbtft_par *par, size_t offset, size_t len)
remain = len / 2;
vmem16 = (u16 *)(par->info->screen_buffer + offset);
- if (par->gpio.dc != -1)
- gpio_set_value(par->gpio.dc, 1);
+ if (!par->gpio.dc)
+ gpiod_set_value(par->gpio.dc, 1);
/* non buffered write */
if (!par->txbuf.buf)
@@ -16,7 +16,7 @@
#include <linux/slab.h>
#include <linux/init.h>
#include <linux/fb.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include <linux/delay.h>
#include <linux/uaccess.h>
@@ -24,7 +24,6 @@
#include <linux/platform_device.h>
#include <linux/spinlock.h>
#include <linux/of.h>
-#include <linux/of_gpio.h>
#include <video/mipi_display.h>
#include "fbtft.h"
@@ -38,8 +37,8 @@ int fbtft_write_buf_dc(struct fbtft_par *par, void *buf, size_t len, int dc)
{
int ret;
- if (gpio_is_valid(par->gpio.dc))
- gpio_set_value(par->gpio.dc, dc);
+ if (par->gpio.dc)
+ gpiod_set_value(par->gpio.dc, dc);
ret = par->fbtftops.write(par, buf, len);
if (ret < 0)
@@ -71,127 +70,27 @@ void fbtft_dbg_hex(const struct device *dev, int groupsize,
}
EXPORT_SYMBOL(fbtft_dbg_hex);
-static unsigned long fbtft_request_gpios_match(struct fbtft_par *par,
- const struct fbtft_gpio *gpio)
-{
- int ret;
- unsigned int val;
-
- fbtft_par_dbg(DEBUG_REQUEST_GPIOS_MATCH, par, "%s('%s')\n",
- __func__, gpio->name);
-
- if (strcasecmp(gpio->name, "reset") == 0) {
- par->gpio.reset = gpio->gpio;
- return GPIOF_OUT_INIT_HIGH;
- } else if (strcasecmp(gpio->name, "dc") == 0) {
- par->gpio.dc = gpio->gpio;
- return GPIOF_OUT_INIT_LOW;
- } else if (strcasecmp(gpio->name, "cs") == 0) {
- par->gpio.cs = gpio->gpio;
- return GPIOF_OUT_INIT_HIGH;
- } else if (strcasecmp(gpio->name, "wr") == 0) {
- par->gpio.wr = gpio->gpio;
- return GPIOF_OUT_INIT_HIGH;
- } else if (strcasecmp(gpio->name, "rd") == 0) {
- par->gpio.rd = gpio->gpio;
- return GPIOF_OUT_INIT_HIGH;
- } else if (strcasecmp(gpio->name, "latch") == 0) {
- par->gpio.latch = gpio->gpio;
- return GPIOF_OUT_INIT_LOW;
- } else if (gpio->name[0] == 'd' && gpio->name[1] == 'b') {
- ret = kstrtouint(&gpio->name[2], 10, &val);
- if (ret == 0 && val < 16) {
- par->gpio.db[val] = gpio->gpio;
- return GPIOF_OUT_INIT_LOW;
- }
- } else if (strcasecmp(gpio->name, "led") == 0) {
- par->gpio.led[0] = gpio->gpio;
- return GPIOF_OUT_INIT_LOW;
- } else if (strcasecmp(gpio->name, "led_") == 0) {
- par->gpio.led[0] = gpio->gpio;
- return GPIOF_OUT_INIT_HIGH;
- }
-
- return FBTFT_GPIO_NO_MATCH;
-}
-
-static int fbtft_request_gpios(struct fbtft_par *par)
-{
- struct fbtft_platform_data *pdata = par->pdata;
- const struct fbtft_gpio *gpio;
- unsigned long flags;
- int ret;
-
- if (!(pdata && pdata->gpios))
- return 0;
-
- gpio = pdata->gpios;
- while (gpio->name[0]) {
- flags = FBTFT_GPIO_NO_MATCH;
- /* if driver provides match function, try it first,
- * if no match use our own
- */
- if (par->fbtftops.request_gpios_match)
- flags = par->fbtftops.request_gpios_match(par, gpio);
- if (flags == FBTFT_GPIO_NO_MATCH)
- flags = fbtft_request_gpios_match(par, gpio);
- if (flags != FBTFT_GPIO_NO_MATCH) {
- ret = devm_gpio_request_one(par->info->device,
- gpio->gpio, flags,
- par->info->device->driver->name);
- if (ret < 0) {
- dev_err(par->info->device,
- "%s: gpio_request_one('%s'=%d) failed with %d\n",
- __func__, gpio->name,
- gpio->gpio, ret);
- return ret;
- }
- fbtft_par_dbg(DEBUG_REQUEST_GPIOS, par,
- "%s: '%s' = GPIO%d\n",
- __func__, gpio->name, gpio->gpio);
- }
- gpio++;
- }
-
- return 0;
-}
-
#ifdef CONFIG_OF
static int fbtft_request_one_gpio(struct fbtft_par *par,
- const char *name, int index, int *gpiop)
+ const char *name, int index,
+ struct gpio_desc **gpiop)
{
struct device *dev = par->info->device;
struct device_node *node = dev->of_node;
- int gpio, flags, ret = 0;
- enum of_gpio_flags of_flags;
+ int ret = 0;
if (of_find_property(node, name, NULL)) {
- gpio = of_get_named_gpio_flags(node, name, index, &of_flags);
- if (gpio == -ENOENT)
- return 0;
- if (gpio == -EPROBE_DEFER)
- return gpio;
- if (gpio < 0) {
+ *gpiop = devm_gpiod_get_index(dev, dev->driver->name, index,
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(*gpiop)) {
+ ret = PTR_ERR(*gpiop);
dev_err(dev,
- "failed to get '%s' from DT\n", name);
- return gpio;
- }
-
- /* active low translates to initially low */
- flags = (of_flags & OF_GPIO_ACTIVE_LOW) ? GPIOF_OUT_INIT_LOW :
- GPIOF_OUT_INIT_HIGH;
- ret = devm_gpio_request_one(dev, gpio, flags,
- dev->driver->name);
- if (ret) {
- dev_err(dev,
- "gpio_request_one('%s'=%d) failed with %d\n",
- name, gpio, ret);
+ "Failed to request %s GPIO:%d\n", name, ret);
return ret;
+
}
- if (gpiop)
- *gpiop = gpio;
- fbtft_par_dbg(DEBUG_REQUEST_GPIOS, par, "%s: '%s' = GPIO%d\n",
- __func__, name, gpio);
+ fbtft_par_dbg(DEBUG_REQUEST_GPIOS, par, "%s: '%s' GPIO\n",
+ __func__, name);
}
return ret;
@@ -254,9 +153,9 @@ static int fbtft_backlight_update_status(struct backlight_device *bd)
if ((bd->props.power == FB_BLANK_UNBLANK) &&
(bd->props.fb_blank == FB_BLANK_UNBLANK))
- gpio_set_value(par->gpio.led[0], polarity);
+ gpiod_set_value(par->gpio.led[0], polarity);
else
- gpio_set_value(par->gpio.led[0], !polarity);
+ gpiod_set_value(par->gpio.led[0], !polarity);
return 0;
}
@@ -286,7 +185,7 @@ void fbtft_register_backlight(struct fbtft_par *par)
struct backlight_device *bd;
struct backlight_properties bl_props = { 0, };
- if (par->gpio.led[0] == -1) {
+ if (!par->gpio.led[0]) {
fbtft_par_dbg(DEBUG_BACKLIGHT, par,
"%s(): led pin not set, exiting.\n", __func__);
return;
@@ -295,7 +194,7 @@ void fbtft_register_backlight(struct fbtft_par *par)
bl_props.type = BACKLIGHT_RAW;
/* Assume backlight is off, get polarity from current state of pin */
bl_props.power = FB_BLANK_POWERDOWN;
- if (!gpio_get_value(par->gpio.led[0]))
+ if (!gpiod_get_value(par->gpio.led[0]))
par->polarity = true;
bd = backlight_device_register(dev_driver_string(par->info->device),
@@ -333,12 +232,12 @@ static void fbtft_set_addr_win(struct fbtft_par *par, int xs, int ys, int xe,
static void fbtft_reset(struct fbtft_par *par)
{
- if (par->gpio.reset == -1)
+ if (!par->gpio.reset)
return;
fbtft_par_dbg(DEBUG_RESET, par, "%s()\n", __func__);
- gpio_set_value_cansleep(par->gpio.reset, 0);
+ gpiod_set_value_cansleep(par->gpio.reset, 0);
usleep_range(20, 40);
- gpio_set_value_cansleep(par->gpio.reset, 1);
+ gpiod_set_value_cansleep(par->gpio.reset, 1);
msleep(120);
}
@@ -663,7 +562,7 @@ struct fb_info *fbtft_framebuffer_alloc(struct fbtft_display *display,
int txbuflen = display->txbuflen;
unsigned int bpp = display->bpp;
unsigned int fps = display->fps;
- int vmem_size, i;
+ int vmem_size;
const s16 *init_sequence = display->init_sequence;
char *gamma = display->gamma;
u32 *gamma_curves = NULL;
@@ -841,19 +740,6 @@ struct fb_info *fbtft_framebuffer_alloc(struct fbtft_display *display,
par->txbuf.len = txbuflen;
}
- /* Initialize gpios to disabled */
- par->gpio.reset = -1;
- par->gpio.dc = -1;
- par->gpio.rd = -1;
- par->gpio.wr = -1;
- par->gpio.cs = -1;
- par->gpio.latch = -1;
- for (i = 0; i < 16; i++) {
- par->gpio.db[i] = -1;
- par->gpio.led[i] = -1;
- par->gpio.aux[i] = -1;
- }
-
/* default fbtft operations */
par->fbtftops.write = fbtft_write_spi;
par->fbtftops.read = fbtft_read_spi;
@@ -863,7 +749,6 @@ struct fb_info *fbtft_framebuffer_alloc(struct fbtft_display *display,
par->fbtftops.reset = fbtft_reset;
par->fbtftops.mkdirty = fbtft_mkdirty;
par->fbtftops.update_display = fbtft_update_display;
- par->fbtftops.request_gpios = fbtft_request_gpios;
if (display->backlight)
par->fbtftops.register_backlight = fbtft_register_backlight;
@@ -1035,8 +920,8 @@ static int fbtft_init_display_dt(struct fbtft_par *par)
return -EINVAL;
par->fbtftops.reset(par);
- if (par->gpio.cs != -1)
- gpio_set_value(par->gpio.cs, 0); /* Activate chip */
+ if (!par->gpio.cs)
+ gpiod_set_value(par->gpio.cs, 0); /* Activate chip */
while (p) {
if (val & FBTFT_OF_INIT_CMD) {
@@ -1126,8 +1011,8 @@ int fbtft_init_display(struct fbtft_par *par)
}
par->fbtftops.reset(par);
- if (par->gpio.cs != -1)
- gpio_set_value(par->gpio.cs, 0); /* Activate chip */
+ if (!par->gpio.cs)
+ gpiod_set_value(par->gpio.cs, 0); /* Activate chip */
i = 0;
while (i < FBTFT_MAX_INIT_SEQUENCE) {
@@ -1227,7 +1112,7 @@ static int fbtft_verify_gpios(struct fbtft_par *par)
fbtft_par_dbg(DEBUG_VERIFY_GPIOS, par, "%s()\n", __func__);
if (pdata->display.buswidth != 9 && par->startbyte == 0 &&
- par->gpio.dc < 0) {
+ !par->gpio.dc) {
dev_err(par->info->device,
"Missing info about 'dc' gpio. Aborting.\n");
return -EINVAL;
@@ -1236,12 +1121,12 @@ static int fbtft_verify_gpios(struct fbtft_par *par)
if (!par->pdev)
return 0;
- if (par->gpio.wr < 0) {
+ if (!par->gpio.wr) {
dev_err(par->info->device, "Missing 'wr' gpio. Aborting.\n");
return -EINVAL;
}
for (i = 0; i < pdata->display.buswidth; i++) {
- if (par->gpio.db[i] < 0) {
+ if (!par->gpio.db[i]) {
dev_err(par->info->device,
"Missing 'db%02d' gpio. Aborting.\n", i);
return -EINVAL;
@@ -1,7 +1,7 @@
// SPDX-License-Identifier: GPL-2.0
#include <linux/export.h>
#include <linux/errno.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include "fbtft.h"
@@ -142,30 +142,30 @@ int fbtft_write_gpio8_wr(struct fbtft_par *par, void *buf, size_t len)
data = *(u8 *)buf;
/* Start writing by pulling down /WR */
- gpio_set_value(par->gpio.wr, 0);
+ gpiod_set_value(par->gpio.wr, 0);
/* Set data */
#ifndef DO_NOT_OPTIMIZE_FBTFT_WRITE_GPIO
if (data == prev_data) {
- gpio_set_value(par->gpio.wr, 0); /* used as delay */
+ gpiod_set_value(par->gpio.wr, 0); /* used as delay */
} else {
for (i = 0; i < 8; i++) {
if ((data & 1) != (prev_data & 1))
- gpio_set_value(par->gpio.db[i],
- data & 1);
+ gpiod_set_value(par->gpio.db[i],
+ data & 1);
data >>= 1;
prev_data >>= 1;
}
}
#else
for (i = 0; i < 8; i++) {
- gpio_set_value(par->gpio.db[i], data & 1);
+ gpiod_set_value(par->gpio.db[i], data & 1);
data >>= 1;
}
#endif
/* Pullup /WR */
- gpio_set_value(par->gpio.wr, 1);
+ gpiod_set_value(par->gpio.wr, 1);
#ifndef DO_NOT_OPTIMIZE_FBTFT_WRITE_GPIO
prev_data = *(u8 *)buf;
@@ -192,30 +192,30 @@ int fbtft_write_gpio16_wr(struct fbtft_par *par, void *buf, size_t len)
data = *(u16 *)buf;
/* Start writing by pulling down /WR */
- gpio_set_value(par->gpio.wr, 0);
+ gpiod_set_value(par->gpio.wr, 0);
/* Set data */
#ifndef DO_NOT_OPTIMIZE_FBTFT_WRITE_GPIO
if (data == prev_data) {
- gpio_set_value(par->gpio.wr, 0); /* used as delay */
+ gpiod_set_value(par->gpio.wr, 0); /* used as delay */
} else {
for (i = 0; i < 16; i++) {
if ((data & 1) != (prev_data & 1))
- gpio_set_value(par->gpio.db[i],
- data & 1);
+ gpiod_set_value(par->gpio.db[i],
+ data & 1);
data >>= 1;
prev_data >>= 1;
}
}
#else
for (i = 0; i < 16; i++) {
- gpio_set_value(par->gpio.db[i], data & 1);
+ gpiod_set_value(par->gpio.db[i], data & 1);
data >>= 1;
}
#endif
/* Pullup /WR */
- gpio_set_value(par->gpio.wr, 1);
+ gpiod_set_value(par->gpio.wr, 1);
#ifndef DO_NOT_OPTIMIZE_FBTFT_WRITE_GPIO
prev_data = *(u16 *)buf;
@@ -27,7 +27,7 @@
*/
struct fbtft_gpio {
char name[FBTFT_GPIO_NAME_SIZE];
- unsigned int gpio;
+ struct gpio_desc *gpio;
};
struct fbtft_par;
@@ -134,7 +134,6 @@ struct fbtft_display {
*/
struct fbtft_platform_data {
struct fbtft_display display;
- const struct fbtft_gpio *gpios;
unsigned int rotate;
bool bgr;
unsigned int fps;
@@ -207,15 +206,15 @@ struct fbtft_par {
unsigned int dirty_lines_start;
unsigned int dirty_lines_end;
struct {
- int reset;
- int dc;
- int rd;
- int wr;
- int latch;
- int cs;
- int db[16];
- int led[16];
- int aux[16];
+ struct gpio_desc *reset;
+ struct gpio_desc *dc;
+ struct gpio_desc *rd;
+ struct gpio_desc *wr;
+ struct gpio_desc *latch;
+ struct gpio_desc *cs;
+ struct gpio_desc *db[16];
+ struct gpio_desc *led[16];
+ struct gpio_desc *aux[16];
} gpio;
const s16 *init_sequence;
struct {
@@ -8,7 +8,7 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include <video/mipi_display.h>
@@ -45,11 +45,6 @@ static int mode = -1;
module_param(mode, int, 0000);
MODULE_PARM_DESC(mode, "SPI mode (override device default)");
-static char *gpios;
-module_param(gpios, charp, 0000);
-MODULE_PARM_DESC(gpios,
- "List of gpios. Comma separated with the form: reset:23,dc:24 (when overriding the default, all gpios must be specified)");
-
static unsigned int fps;
module_param(fps, uint, 0000);
MODULE_PARM_DESC(fps, "Frames per second (override driver default)");
@@ -101,7 +96,7 @@ MODULE_PARM_DESC(debug,
static unsigned int verbose = 3;
module_param(verbose, uint, 0000);
MODULE_PARM_DESC(verbose,
- "0 silent, >0 show gpios, >1 show devices, >2 show devices before (default=3)");
+ "0 silent, >1 show devices, >2 show devices before (default=3)");
struct fbtft_device_display {
char *name;
@@ -279,12 +274,6 @@ static struct fbtft_device_display displays[] = {
.buswidth = 8,
.backlight = 1,
},
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 18 },
- {},
- },
.gamma = ADAFRUIT18_GAMMA,
}
}
@@ -302,12 +291,6 @@ static struct fbtft_device_display displays[] = {
adafruit18_green_tab_set_addr_win,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 18 },
- {},
- },
.gamma = ADAFRUIT18_GAMMA,
}
}
@@ -323,11 +306,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "led", 23 },
- {},
- },
}
}
}, {
@@ -342,12 +320,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 18 },
- {},
- },
}
}
}, {
@@ -362,12 +334,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 18 },
- {},
- },
}
}
}, {
@@ -380,11 +346,6 @@ static struct fbtft_device_display displays[] = {
.display = {
.buswidth = 8,
},
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- {},
- },
}
}
}, {
@@ -399,12 +360,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
.init_sequence = cberry28_init_sequence,
},
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 22 },
- { "led", 18 },
- {},
- },
.gamma = CBERRY28_GAMMA,
}
}
@@ -420,9 +375,6 @@ static struct fbtft_device_display displays[] = {
.buswidth = 8,
.backlight = FBTFT_ONBOARD_BACKLIGHT,
},
- .gpios = (const struct fbtft_gpio []) {
- {},
- },
},
}
}
@@ -437,11 +389,6 @@ static struct fbtft_device_display displays[] = {
.buswidth = 8,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 13 },
- { "dc", 6 },
- {},
- },
}
}
}, {
@@ -458,11 +405,6 @@ static struct fbtft_device_display displays[] = {
.height = 272,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- {},
- },
}
}
}, {
@@ -479,11 +421,6 @@ static struct fbtft_device_display displays[] = {
.height = 480,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- {},
- },
}
}
}, {
@@ -496,10 +433,6 @@ static struct fbtft_device_display displays[] = {
.display = {
.buswidth = 8,
},
- .gpios = (const struct fbtft_gpio []) {
- { "dc", 24 },
- {},
- },
}
}
}, {
@@ -512,9 +445,6 @@ static struct fbtft_device_display displays[] = {
.display = {
.buswidth = 9,
},
- .gpios = (const struct fbtft_gpio []) {
- {},
- },
}
}
}, {
@@ -523,13 +453,6 @@ static struct fbtft_device_display displays[] = {
.modalias = "flexfb",
.max_speed_hz = 32000000,
.mode = SPI_MODE_0,
- .platform_data = &(struct fbtft_platform_data) {
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- {},
- },
- }
}
}, {
.name = "flexpfb",
@@ -538,24 +461,6 @@ static struct fbtft_device_display displays[] = {
.id = 0,
.dev = {
.release = fbtft_device_pdev_release,
- .platform_data = &(struct fbtft_platform_data) {
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 17 },
- { "dc", 1 },
- { "wr", 0 },
- { "cs", 21 },
- { "db00", 9 },
- { "db01", 11 },
- { "db02", 18 },
- { "db03", 23 },
- { "db04", 24 },
- { "db05", 25 },
- { "db06", 8 },
- { "db07", 7 },
- { "led", 4 },
- {},
- },
- },
}
}
}, {
@@ -570,11 +475,6 @@ static struct fbtft_device_display displays[] = {
.backlight = FBTFT_ONBOARD_BACKLIGHT,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 24 },
- { "dc", 25 },
- {},
- },
}
}
}, {
@@ -588,12 +488,6 @@ static struct fbtft_device_display displays[] = {
.buswidth = 8,
.backlight = 1,
},
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 23 },
- {},
- },
}
}
}, {
@@ -609,11 +503,6 @@ static struct fbtft_device_display displays[] = {
},
.startbyte = 0x70,
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "led", 18 },
- {},
- },
}
}
}, {
@@ -631,11 +520,6 @@ static struct fbtft_device_display displays[] = {
.startbyte = 0x70,
.bgr = true,
.fps = 50,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "led", 18 },
- {},
- },
.gamma = HY28B_GAMMA,
}
}
@@ -652,12 +536,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 22 },
- {},
- },
}
}
}, {
@@ -673,22 +551,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = false,
- .gpios = (const struct fbtft_gpio []) {
- /* Wiring for LCD adapter kit */
- { "reset", 7 },
- { "dc", 0 }, /* rev 2: 2 */
- { "wr", 1 }, /* rev 2: 3 */
- { "cs", 8 },
- { "db00", 17 },
- { "db01", 18 },
- { "db02", 21 }, /* rev 2: 27 */
- { "db03", 22 },
- { "db04", 23 },
- { "db05", 24 },
- { "db06", 25 },
- { "db07", 4 },
- {}
- },
},
}
}
@@ -705,9 +567,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- {},
- },
},
}
}
@@ -723,11 +582,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- {},
- },
}
}
}, {
@@ -743,12 +597,6 @@ static struct fbtft_device_display displays[] = {
},
.startbyte = 0x70,
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 18 },
- {},
- },
}
}
}, {
@@ -763,11 +611,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "led", 18 },
- {},
- },
}
}
}, {
@@ -777,10 +620,6 @@ static struct fbtft_device_display displays[] = {
.max_speed_hz = 4000000,
.mode = SPI_MODE_3,
.platform_data = &(struct fbtft_platform_data) {
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- {},
- },
}
}
}, {
@@ -793,12 +632,6 @@ static struct fbtft_device_display displays[] = {
.display = {
.buswidth = 8,
},
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 23 },
- {},
- },
}
}
}, {
@@ -811,12 +644,6 @@ static struct fbtft_device_display displays[] = {
.display = {
.buswidth = 8,
},
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 23 },
- {},
- },
}
}
}, {
@@ -831,9 +658,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- {},
- },
}
}
}, {
@@ -849,12 +673,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 22 },
- {},
- },
}
}
}, {
@@ -871,10 +689,6 @@ static struct fbtft_device_display displays[] = {
.init_sequence = pitft_init_sequence,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "dc", 25 },
- {},
- },
}
}
}, {
@@ -888,11 +702,6 @@ static struct fbtft_device_display displays[] = {
.buswidth = 8,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 24 },
- { "dc", 25 },
- {},
- },
.gamma = PIOLED_GAMMA
}
}
@@ -908,12 +717,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 23 },
- { "dc", 24 },
- { "led", 18 },
- {},
- },
}
}
}, {
@@ -928,12 +731,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 23 },
- {},
- },
}
}
}, {
@@ -946,11 +743,6 @@ static struct fbtft_device_display displays[] = {
.display = {
.buswidth = 8,
},
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- {},
- },
}
}
}, {
@@ -968,9 +760,6 @@ static struct fbtft_device_display displays[] = {
.fbtftops.write = write_gpio16_wr_slow,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- {},
- },
},
},
}
@@ -988,9 +777,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- {},
- },
},
},
}
@@ -1010,9 +796,6 @@ static struct fbtft_device_display displays[] = {
fbtft_write_gpio16_wr_latched,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- {},
- },
},
},
}
@@ -1028,11 +811,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- {},
- },
}
}
}, {
@@ -1044,9 +822,6 @@ static struct fbtft_device_display displays[] = {
.chip_select = 0,
.mode = SPI_MODE_0,
.platform_data = &(struct fbtft_platform_data) {
- .gpios = (const struct fbtft_gpio []) {
- {},
- },
}
}
}, {
@@ -1059,11 +834,6 @@ static struct fbtft_device_display displays[] = {
.display = {
.buswidth = 8,
},
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 24 },
- { "dc", 25 },
- {},
- },
}
}
}, {
@@ -1078,12 +848,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 18 },
- {},
- },
}
}
}, {
@@ -1098,12 +862,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 25 },
- { "dc", 24 },
- { "led", 18 },
- {},
- },
}
}
}, {
@@ -1118,12 +876,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 15 },
- { "dc", 25 },
- { "led_", 18 },
- {},
- },
}
}
}, {
@@ -1138,12 +890,6 @@ static struct fbtft_device_display displays[] = {
.backlight = 1,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 15 },
- { "dc", 25 },
- { "led_", 18 },
- {},
- },
}
}
}, {
@@ -1156,11 +902,6 @@ static struct fbtft_device_display displays[] = {
.display = {
.buswidth = 8,
},
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 24 },
- { "dc", 25 },
- {},
- },
}
}
}, {
@@ -1177,11 +918,6 @@ static struct fbtft_device_display displays[] = {
waveshare32b_init_sequence,
},
.bgr = true,
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 27 },
- { "dc", 22 },
- {},
- },
}
}
}, {
@@ -1194,11 +930,6 @@ static struct fbtft_device_display displays[] = {
.display = {
.buswidth = 8,
},
- .gpios = (const struct fbtft_gpio []) {
- { "reset", 24 },
- { "dc", 25 },
- {},
- },
}
}
}, {
@@ -1211,9 +942,6 @@ static struct fbtft_device_display displays[] = {
.max_speed_hz = 0,
.mode = SPI_MODE_0,
.platform_data = &(struct fbtft_platform_data) {
- .gpios = (const struct fbtft_gpio []) {
- {},
- },
}
},
.pdev = &(struct platform_device) {
@@ -1222,9 +950,6 @@ static struct fbtft_device_display displays[] = {
.dev = {
.release = fbtft_device_pdev_release,
.platform_data = &(struct fbtft_platform_data) {
- .gpios = (const struct fbtft_gpio []) {
- {},
- },
},
},
},
@@ -1246,30 +971,30 @@ static int write_gpio16_wr_slow(struct fbtft_par *par, void *buf, size_t len)
data = *(u16 *)buf;
/* Start writing by pulling down /WR */
- gpio_set_value(par->gpio.wr, 0);
+ gpiod_set_value(par->gpio.wr, 0);
/* Set data */
#ifndef DO_NOT_OPTIMIZE_FBTFT_WRITE_GPIO
if (data == prev_data) {
- gpio_set_value(par->gpio.wr, 0); /* used as delay */
+ gpiod_set_value(par->gpio.wr, 0); /* used as delay */
} else {
for (i = 0; i < 16; i++) {
if ((data & 1) != (prev_data & 1))
- gpio_set_value(par->gpio.db[i],
- data & 1);
+ gpiod_set_value(par->gpio.db[i],
+ data & 1);
data >>= 1;
prev_data >>= 1;
}
}
#else
for (i = 0; i < 16; i++) {
- gpio_set_value(par->gpio.db[i], data & 1);
+ gpiod_set_value(par->gpio.db[i], data & 1);
data >>= 1;
}
#endif
/* Pullup /WR */
- gpio_set_value(par->gpio.wr, 1);
+ gpiod_set_value(par->gpio.wr, 1);
#ifndef DO_NOT_OPTIMIZE_FBTFT_WRITE_GPIO
prev_data = *(u16 *)buf;
@@ -1289,9 +1014,6 @@ static void adafruit18_green_tab_set_addr_win(struct fbtft_par *par,
write_reg(par, 0x2C);
}
-/* used if gpios parameter is present */
-static struct fbtft_gpio fbtft_device_param_gpios[MAX_GPIOS + 1] = { };
-
static void fbtft_device_pdev_release(struct device *dev)
{
/* Needed to silence this message:
@@ -1382,11 +1104,8 @@ static int __init fbtft_device_init(void)
{
struct spi_board_info *spi = NULL;
struct fbtft_platform_data *pdata;
- const struct fbtft_gpio *gpio = NULL;
- char *p_gpio, *p_name, *p_num;
bool found = false;
int i = 0;
- long val;
int ret = 0;
if (!name) {
@@ -1404,38 +1123,6 @@ static int __init fbtft_device_init(void)
return -EINVAL;
}
- /* parse module parameter: gpios */
- while ((p_gpio = strsep(&gpios, ","))) {
- if (!strchr(p_gpio, ':')) {
- pr_err("error: missing ':' in gpios parameter: %s\n",
- p_gpio);
- return -EINVAL;
- }
- p_num = p_gpio;
- p_name = strsep(&p_num, ":");
- if (!p_name || !p_num) {
- pr_err("something bad happened parsing gpios parameter: %s\n",
- p_gpio);
- return -EINVAL;
- }
- ret = kstrtol(p_num, 10, &val);
- if (ret) {
- pr_err("could not parse number in gpios parameter: %s:%s\n",
- p_name, p_num);
- return -EINVAL;
- }
- strncpy(fbtft_device_param_gpios[i].name, p_name,
- FBTFT_GPIO_NAME_SIZE - 1);
- fbtft_device_param_gpios[i++].gpio = (int)val;
- if (i == MAX_GPIOS) {
- pr_err("gpios parameter: exceeded max array size: %d\n",
- MAX_GPIOS);
- return -EINVAL;
- }
- }
- if (fbtft_device_param_gpios[0].name[0])
- gpio = fbtft_device_param_gpios;
-
if (verbose > 2) {
pr_spi_devices(); /* print list of registered SPI devices */
pr_p_devices(); /* print list of 'fb' platform devices */
@@ -1516,8 +1203,6 @@ static int __init fbtft_device_init(void)
pdata->txbuflen = txbuflen;
if (init_num)
pdata->display.init_sequence = init;
- if (gpio)
- pdata->gpios = gpio;
if (custom) {
pdata->display.width = width;
pdata->display.height = height;
@@ -1549,19 +1234,6 @@ static int __init fbtft_device_init(void)
return -EINVAL;
}
- if (verbose && pdata && pdata->gpios) {
- gpio = pdata->gpios;
- pr_info("GPIOS used by '%s':\n", name);
- found = false;
- while (verbose && gpio->name[0]) {
- pr_info("'%s' = GPIO%d\n", gpio->name, gpio->gpio);
- gpio++;
- found = true;
- }
- if (!found)
- pr_info("(none)\n");
- }
-
if (spi_device && (verbose > 1))
pr_spi_devices();
if (p_device && (verbose > 1))
@@ -9,7 +9,7 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/vmalloc.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/spi/spi.h>
#include <linux/delay.h>
@@ -521,7 +521,7 @@ static int flexfb_verify_gpios_dc(struct fbtft_par *par)
{
fbtft_par_dbg(DEBUG_VERIFY_GPIOS, par, "%s()\n", __func__);
- if (par->gpio.dc < 0) {
+ if (!par->gpio.dc) {
dev_err(par->info->device,
"Missing info about 'dc' gpio. Aborting.\n");
return -EINVAL;
@@ -537,22 +537,22 @@ static int flexfb_verify_gpios_db(struct fbtft_par *par)
fbtft_par_dbg(DEBUG_VERIFY_GPIOS, par, "%s()\n", __func__);
- if (par->gpio.dc < 0) {
+ if (!par->gpio.dc) {
dev_err(par->info->device, "Missing info about 'dc' gpio. Aborting.\n");
return -EINVAL;
}
- if (par->gpio.wr < 0) {
+ if (!par->gpio.wr) {
dev_err(par->info->device, "Missing info about 'wr' gpio. Aborting.\n");
return -EINVAL;
}
- if (latched && (par->gpio.latch < 0)) {
+ if (latched && !par->gpio.latch) {
dev_err(par->info->device, "Missing info about 'latch' gpio. Aborting.\n");
return -EINVAL;
}
if (latched)
num_db = buswidth / 2;
for (i = 0; i < num_db; i++) {
- if (par->gpio.db[i] < 0) {
+ if (!par->gpio.db[i]) {
dev_err(par->info->device,
"Missing info about 'db%02d' gpio. Aborting.\n",
i);
This switches the fbtft driver to use GPIO descriptors rather than numerical gpios: Utilize the GPIO library's intrinsic handling of OF GPIOs and polarity. If the line is flagged active low, gpiolib will deal with this. Remove gpios from platform device structure. Neither assign statically numbers to gpios in platform device nor allow gpios to be parsed as module parameters. Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com> Changes in v2: - Merge all patches in a single patch. This is because the first patch changes par->gpio from an int to a pointer so all the checks have to be updated in the same patch. Otherwie it breaks 'git bisect'. --- drivers/staging/fbtft/fb_agm1264k-fl.c | 52 ++-- drivers/staging/fbtft/fb_bd663474.c | 6 +- drivers/staging/fbtft/fb_ili9163.c | 6 +- drivers/staging/fbtft/fb_ili9320.c | 2 +- drivers/staging/fbtft/fb_ili9325.c | 6 +- drivers/staging/fbtft/fb_ili9340.c | 2 +- drivers/staging/fbtft/fb_pcd8544.c | 4 +- drivers/staging/fbtft/fb_ra8875.c | 4 +- drivers/staging/fbtft/fb_s6d1121.c | 6 +- drivers/staging/fbtft/fb_sh1106.c | 2 +- drivers/staging/fbtft/fb_ssd1289.c | 6 +- drivers/staging/fbtft/fb_ssd1305.c | 4 +- drivers/staging/fbtft/fb_ssd1306.c | 4 +- drivers/staging/fbtft/fb_ssd1325.c | 6 +- drivers/staging/fbtft/fb_ssd1331.c | 10 +- drivers/staging/fbtft/fb_ssd1351.c | 2 +- drivers/staging/fbtft/fb_tls8204.c | 6 +- drivers/staging/fbtft/fb_uc1611.c | 4 +- drivers/staging/fbtft/fb_uc1701.c | 6 +- drivers/staging/fbtft/fb_upd161704.c | 6 +- drivers/staging/fbtft/fb_watterott.c | 4 +- drivers/staging/fbtft/fbtft-bus.c | 6 +- drivers/staging/fbtft/fbtft-core.c | 173 +++---------- drivers/staging/fbtft/fbtft-io.c | 26 +- drivers/staging/fbtft/fbtft.h | 21 +- drivers/staging/fbtft/fbtft_device.c | 344 +------------------------ drivers/staging/fbtft/flexfb.c | 12 +- 27 files changed, 143 insertions(+), 587 deletions(-)